SEARCH · Search NASA

Results for “STOL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Lessons learned in the development of the STOL intelligent tutoring system

Lessons learned during the development of the NASA Systems Test and Operations Language (STOL) Intelligent Tutoring System (ITS), being developed at NASA Goddard Space Flight Center are presented. The purpose of the intelligent tutor is to train STOL users by adapting tutoring based on inferred student strengths and weaknesses. This system has been under development for over one year and numerous lessons learned have emerged. These observations are presented in three sections, as follows. The first section addresses the methodology employed in the development of the STOL ITS and briefly presents the ITS architecture. The second presents lessons learned, in the areas of: intelligent tutor development; documentation and reporting; cost and schedule control; and tools and shells effectiveness. The third section presents recommendations which may be considered by other ITS developers, addressing: access, use and selection of subject matter experts; steps involved in ITS development; use of ITS interface design prototypes as part of knowledge engineering; and tools and shells effectiveness.

Seamster, Thomas↗

NASA NTRS1965

Some Performance and Handling-Qualities Considerations for Operation of STOL Aircraft

Studies of a number of STOL aircraft show that relatively high maximum lift-coefficients and large increases in lift due to power are within the present state of the art. With these lift characteristics, approach speeds of the order of 60 knots for aircraft of moderate wing loading can be realized. Full advantage of the STOL performance of aircraft such as those discussed herein may not be realized on a routine operational basis, however, without some form of damping augmentation system because of lateral-directional handling considerations, particularly for large aircraft operating under instrument flight conditions. Satisfactory characteristics can be obtained by use of only a servodriven rudder. Additional experience is needed to determine how the STOL aircraft is to be operated before more firm requirements for augmentation systems can be established.

Anderson, Seth B.↗

NASA NTRS2002

Development of Pneumatic Channel Wing Powered-Lift Advanced Super-STOL Aircraft

The powered-lift Channel Wing concept has been combined with pneumatic Circulation Control aerodynamic and propulsive technology to generate a Pneumatic Channel Wing configuration intended to have Super-STOL or VSTOL capability while eliminating many of the operational problem areas of the original Channel Wing vehicle. A preliminary design study of this pneumatic vehicle based on previous wind-tunnel and flight-test data for the two technologies integrated into a simple Pneumatic Channel Wing (PCW) configuration showed very strong Super-STOL potential. Wind-tunnel development and evaluations of a PCW powered model conducted at Georgia Tech Research Institute (GTRI) have shown substantial lift capabilities for the blown configuration (C(sub L) values of 8.5 to 9.0). Variation in blowing of the channel was shown to be more efficient than variation in propeller thrust. Also revealed was the ability to operate unstalled at very high angles of attack of 40 deg-45 deg, or to achieve very high lift at much lower angle of attack to increase visibility and controllability. In order to provide greater flexibility in Super-STOL takeoffs and landings, the blown model also displayed the ability to interchange thrust and drag by varying blowing without any moving parts. This paper presents these experimental results, discusses variations in the configuration geometry under development, and extends this integrated technology to advanced design studies of PCW-type vehicles.

Englar, Robert J.↗

NASA NTRS1961

A Flight Examination of Operating Problems of V/STOL Aircraft in STOL-Type Landing and Approach

A flight investigation has been conducted using a large twin-engine cargo aircraft to isolate the problems associated with operating propeller-driven aircraft in the STOL speed range where appreciable engine power is used to augment aerodynamic lift. The problems considered would also be representative of those of a large overloaded VTOL aircraft operating in an STOL manner with comparable thrust-to-weight ratios. The study showed that operation at low approach speeds was compromised by the necessity of maintaining high thrust to generate high lift and yet achieving the low lift-drag ratios needed for steep descents. The useable range of airspeed and flight path angle was limited by the pilot's demand for a positive climb margin at the approach speed, a suitable stall margin, and a control and/or performance margin for one engine inoperative. The optimum approach angle over an obstacle was found to be a compromise between obtaining the shortest air distance and the lowest touchdown velocity. In order to realize the greatest low-speed potential from STOL designs, the stability and control characteristics must be satisfactory.

Innis, Robert C.↗

NASA NTRS2005

Experimental Development and Evaluation of Pneumatic Powered-Lift Super-STOL Aircraft

The powered-lift Channel Wing concept has been combined with pneumatic Circulation Control aerodynamic and propulsive technology to generate a Pneumatic Channel Wing (PCW) configuration intended to have Super-STOL or VSTOL capability while eliminating many of the operational problem areas of the original Channel Wing vehicle. Wind-tunnel development and evaluations of a PCW powered model conducted at Georgia Tech Research Institute (GTRI) have shown substantial lift capabilities for the blown configuration (CL values of 10 to 11). Variation in blowing of the channel was shown to be more efficient than variation in propeller thrust in terms of lift generation. Also revealed was the ability to operate unstalled at very high angles of attack of 40 deg - 45 deg, or to achieve very high lift at much lower angle of attack to increase visibility and controllability. In order to provide greater flexibility in Super-STOL takeoffs and landings, the blown model also displayed the ability to interchange thrust and drag by varying blowing without any moving parts. A preliminary design study of this pneumatic vehicle based on the two technologies integrated into a simple Pneumatic Channel Wing configuration showed very strong Super-STOL potential. This paper presents these experimental results, discusses variations in the configuration geometry under development, and addresses additional considerations to extend this integrated technology to advanced design studies of PCW-type vehicles.

Englar, Robert J.↗

NASA NTRS2008

Wind Tunnel Testing of Powered Lift, All-Wing STOL Model

Short take-off and landing (STOL) systems can offer significant capabilities to warfighters and, for civil operators thriving on maximizing efficiencies they can improve airspace use while containing noise within airport environments. In order to provide data for next generation systems, a wind tunnel test of an all-wing cruise efficient, short take-off and landing (CE STOL) configuration was conducted in the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) 14- by 22-foot Subsonic Wind Tunnel. The test s purpose was to mature the aerodynamic aspects of an integrated powered lift system within an advanced mobility configuration capable of CE STOL. The full-span model made use of steady flap blowing and a lifting centerbody to achieve high lift coefficients. The test occurred during April through June of 2007 and included objectives for advancing the state-of-the-art of powered lift testing through gathering force and moment data, on-body pressure data, and off-body flow field measurements during automatically controlled blowing conditions. Data were obtained for variations in model configuration, angles of attack and sideslip, blowing coefficient, and height above ground. The database produced by this effort is being used to advance design techniques and computational tools for developing systems with integrated powered lift technologies.

Collins, Scott W.↗

NASA NTRS1966

Conference on V/STOL and STOL aircraft

This compilation contains results of recent NASA research on problems associated with V/STOL and STOL aircraft. The first three sections include papers presented at the NASA Conference on V/STOL and STOL Aircraft held at the Ames Research Center, Moffett Field, California, on April 4 and 5, 1966. The fourth section presents three additional papers on research testing techniques that are particularly pertinent to the subject matter, but were not presented orally at the conference. Contributors include staff members from the Ames and Langley Research Centers of NASA and industrial representatives from Lockheed Aircraft Corporation; Ling-Temco-Vought, Incorporated; and The Boeing Company.

STOL AIRCRAFT↗

NASA NTRS1971

A preliminary study of containment concepts for aircraft landing on elevated STOL-ports

A preliminary study of containment systems for aircraft landing on elevated STOL-ports was conducted as part of an overall study of human acceptance problems associated with STOL operations. The study included a survey and feasibility study of different concepts and a computer analysis of four arrestment systems. The principal conclusion was that a system referred to as the FAA system appears to offer the greatest promise. In this system, standard arresting gear cables are stretched across the roof-top, at roughly 100-foot intervals, but are shielded over the 100-foot-wide primary landing strip. Thus a pilot can land with an arresting hook down, but will not contact the cable unless he swerves off the landing strip, either because he has made a bad landing, or because his landing gear has failed. It was also noted that a suitable curb or guard rail should be developed. Presently available arresting gears and nylon net barriers were considered satisfactory for the overshoot problem.

Haviland, J. K.↗

NASA NTRS1972

A design support simulation of the augmentor wing jet STOL research aircraft

The modification of a C-8A (De Havilland Buffalo) aircraft to a STOL configuration is discussed. The modification consisted of the installation of an augmentor-wing jet flap system. System design requirements were investigated for the lateral and directional flight control systems, the lateral and directional axes stability augmentation systems, the engine and Pegasus nozzle control systems, and the hydraulic systems. Operational techniques for STOL landings, control of engine failures, and pilot techniques for improving engine-out go-around performance were examined. Design changes have been identified to correct deficiencies in areas of the airplane control sytems and to improve the airplane flying qualities.

Rumsey, P. C.↗

NASA NTRS1972

Experimental measurements of motion cue effects on STOL approach tasks

An experimental program to investigate the effects of motion cues on STOL approach is presented. The simulator used was the Six-Degrees-of-Freedom Motion Simulator (S.01) at Ames Research Center of NASA which has ?2.7 m travel longitudinally and laterally and ?2.5 m travel vertically. Three major experiments, characterized as tracking tasks, were conducted under fixed and moving base conditions: (1) A simulated IFR approach of the Augmentor Wing Jet STOL Research Aircraft (AWJSRA), (2) a simulated VFR task with the same aircraft, and (3) a single-axis task having only linear acceleration as the motion cue. Tracking performance was measured in terms of the variances of several motion variables, pilot vehicle describing functions, and pilot commentary.

Ringland, R. F.↗

NASA NTRS1972

Predicted upwash angles at engine inlets for STOL aircraft

Upwash angles were predicted for a STOL lifting system by using a two-dimensional potential flow analysis. Upwash angles are presented for distances ahead of the wing leading edge of 50, 75, and 100 percent of wing chord. The upwash angle was determined to be insensitive to the vertical location of the engine inlet. For a wide range of takeoff and landing conditions, the upwash angle was found to be a function of the total two-dimensional lift coefficient. Upwash angles, along with typical flow fields, are presented for a range of total two-dimensional lift coefficients from 2 to 12. Three-dimensional effects were considered in estimating upwash angles for an unswept-wing externally blown flap aircraft. For this STOL configuration, effective upwash angles during takeoff, approach, and waveoff conditions were found to be 22 deg, 26 deg, and 36 deg, respectively.

Albers, J. A.↗

NASA NTRS1972

Design integration and noise studies for jet STOL aircraft. Volume 1: Program summary

This program was undertaken to develop, through analysis, design, experimental static testing, wind tunnel testing, and design integration studies, an augmentor wing jet flap configuration for a jet STOL transport aircraft having maximum propulsion and aerodynamic performance with minimum noise generation. The program had three basic elements: (1) static testing of a scale wing section to demonstrate augmentor performance and noise characteristics; (2) two-dimensional wind tunnel testing to determine flight speed effects on performance; and (3) system design and evaluation which integrated the augmentor information obtained into a complete system and ensured that the design was compatible with the requirements for a large STOL transport having a 500-ft sideline noise of 95 PNdB or less. This objective has been achieved.

Okeefe, V. O.↗

NASA NTRS1972

Fixed base simulator study of an externally blown flap STOL transport airplane during approach and landing

A fixed-base simulator study was conducted to determine the flight characteristics of a representative STOL transport having a high wing and equipped with an external-flow jet flap in combination with four high-bypass-ratio fan-jet engines during the approach and landing. Real-time digital simulation techniques were used. The computer was programed with equations of motion for six degrees of freedom and the aerodynamic inputs were based on measured wind-tunnel data. A visual display of a STOL airport was provided for simulation of the flare and touchdown characteristics. The primary piloting task was an instrument approach to a breakout at a 200-ft ceiling with a visual landing.

Grantham, W. D.↗

NASA NTRS1972

Prospects for low wing-loading STOL transports with ride smoothing.

Airplanes with low wing-loadings provide STOL capability without reliance on auxiliary propulsion or augmented lift, but require a ride smoothing control system to provide acceptable passenger comfort. A parametric study produced a configuration having a .35 thrust-to-weight ratio and a 50 psf wing loading, and which satisfied specified mission requirements and airworthiness standards. A ride-smoothing control system (RCS) synthesis was then performed which consisted of ride quality criteria definition, RCS concept trades, and analysis of RCS performance benefits at significant flight conditions. Within the limitations of the study it is concluded that this is a viable approach to STOL airplane design.

Holloway, R. B.↗

NASA NTRS1972

An experimental investigation of STOL longitudinal flying qualities in the landing approach using the variable stability X-22A aircraft.

The first in-flight flying qualities experiment using the variable stability X-22A aircraft investigated longitudinal flying qualities requirements for STOL aircraft in terminal area operations. Emphasis was placed on defining minimum requirements for the short-term response in VFR and IFR landing approaches at representative steep STOL approach conditions of 65 and 80 knots. Evaluation flights were conducted in negligible and moderate turbulence for a wide range of short-term frequencies and dampings. The results were compared with the short-term requirements of MIL-F-83300. The specified Level 1 and 2 VFR boundaries were found to be approximately valid in moderate turbulence for both VFR and IFR flight conditions. In negligible turbulence, the specified VFR Level 2 boundary was also approximately valid but the Level 1 boundary was found to be too stringent. Pilot rating gradients with damping were more apparent than with frequency for the range investigated.

Schuler, J. M.↗

NASA NTRS1972

Use of the flight simulator in the design of a STOL research aircraft.

Piloted simulator tests on the NASA-Ames Flight Simulator for Advanced Aircraft motion base played a major role in guiding the design of the Modified C-8A 'Buffalo' augmentor wing jet flap STOL research airplane. Design results are presented for the flight control systems, lateral-directional SAS, hydraulic systems, and engine and thrust vector controls. Emphasis is given to lateral control characteristics on STOL landing approach, engine-out control and recovery techniques in the powered-lift regime, and operational flight procedures which affected airplane design.

Spitzer, R. E.↗

NASA NTRS1972

STOL noise sources and fan noise treatment

STOL noise goals, noise sources, and their affects on engine and propulsion systems design are considered. It is shown that major noise sources constitute the blown-flap system with its turbofan engine and the augmentor wing propulsion system. Most of the problem areas associated with STOL propulsion systems are defined and the development of a multistage fan engine with proper rotor-stator spacings and low noise core exhaust jet is illustrated. A variable-area acoustic inlet provides near sonic flow conditions during takeoff and landing.

Rulis, R. J.↗

NASA NTRS1972

Design integration and noise study for a large STOL augmentor wing transport

Analysis, design, experimental static testing, wind-tunnel testing, and design integration studies are used to develop an augmentor wing jet flap configuration for a jet STOL transport aircraft having maximum propulsion and aerodynamic performance with minimum noise generation. The program has three basic elements: (1) static testing of a scale wing section to demonstrate augmentor performance and noise characteristics; (2) two-dimensional wind-tunnel testing to determine flight-speed effects on performance, and (3) system design and evaluation that optimizes the complete system and ensures that the design is compatible with the requirements for a large STOL transport having a 500-foot sideline noise of 95 perceived noise decibels (PNdb) or less.

Okeeke, J. V.↗