Search NASA⌕ Search

SEARCH · Search NASA

Results for “SURFACE LAYER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Strain energy density and surface layer energy for a crack-like ellipse

Some of the fundamental concepts of sharp crack fracture criteria are applied to cracks and narrow ellipses. The strain energy density theory is extended to notch boundaries, where the energy in a surface layer is calculated and the location of failure initiation is determined. The concept of a core region near the notch tip, and its consequences, are examined in detail. The example treated is that of an elliptical cavity loaded uniformly at a large distance from the hole, and at an angle to the hole; the results are shown to approach that of the crack solution for narrow ellipses, and to display quite satisfactory agreement with recently published experimental data under both tensile and compressive loading conditions. Results also indicate that in globally unstable configurations in brittle materials, the original loading and notch geometry are sufficient to predict the subsequent crack trajectory with considerable accuracy.

Kipp, M. E.↗
NASA NTRS1972

Thermal characteristics of the lunar surface layer.

The thermophysical properties of the fines from the Apollo 12 landing site have been determined as a function of their relevant parameters. These properties include the thermal conductivity, thermal diffusivity, directional reflectance and emittance. The density used was the same as that observed from the returned core-tube samples and so should be close to the true density of the surface layer at the Apollo 12 site. The measured properties are used to calculate the diurnal temperature variation of the moon's surface as well as for several depths below the surface. The maximum surface of 389 K is obtained at lunar noon while the minimum temperature of 86.1 K is obtained at sunrise. It is shown that the most significant effects on temperature, as compared with previous calculations, are caused by using the directional reflectance which controls the amount of solar energy absorption during the day in place of a constant hemispherical reflectance. The results are compared with previous analyses and remote measurements.

Cremers, C. J.↗
DOE OSTI2022

Engineering Caldicellulosiruptor bescii with Surface Layer Homology Domain-Linked Glycoside Hydrolases Improves Plant Biomass Solubilization

Caldicellulosiruptor species hold promise as microorganisms that can solubilize the carbohydrate portion of lignocellulose and subsequently convert fermentable sugars into bio-based chemicals and fuels. Members of the genus have surface layer (S-layer) homology domain-associated glycoside hydrolases (SLH-GHs) that mediate attachment to biomass as well as hydrolysis of carbohydrates. Caldicellulosiruptor bescii , the most studied member of the genus, has only one SLH-GH.

Biotechnology & Applied Microbiology↗
DOE OSTI2024

Reply to Comment on ‘Deuterium supersaturated surface layer in tungsten: ion energy dependence’

Abstract We reply to the comment by Li et al (submitted to Nucl. Fusion with this response) on our recent paper Nishijima et al (2023 Nucl. Fusion 63 126003). In this response, we address the existence of an incident ion energy, E i , threshold for the deuterium (D) supersaturated surface layer (DSSL) formation with a newly conducted D plasma exposure experiment at E i ∼ 20 eV. It is also further demonstrated, based on new experiments where the ion flux, fluence, and sample temperature are scanned, that non-kinetic (ballistic) processes play a role in the DSSL formation and growth. In addition, the effect of impurities in our plasma is discussed also with a new analysis of the surface composition made after a D plasma exposure.

Nishijima, D. (ORCID:0000000231194827)↗
NASA NTRS1996

Leaf Area Influence on Surface Layer in a Deciduous Forest: Detecting Leaf Area and Surface Resistance During Transition Seasons - Part 2

Temperate deciduous forest exhibit dramatic seasonal changes in surface exchange properties following on the seasonal changes in leaf area index. The canopy resistance to water vapor transport r(sub c) decreased abruptly at leaf emergence in each year but then also continued to decrease slowly during the remaining growing season due to slowly increasing LAI. Canopy resistance and PAR-albedo (albedo from photosynthetically active radiation) began to increase about one month before leaf fall with the diminishment of CO2 gradient above the canopy as well. At this time evaporation begun to be controlled as if the canopy were leafless.

Sakai, Ricardo K.↗
DOE OSTI2025

Friction surface layer deposition of triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high entropy alloy: Process optimization and microstructural evolution

A high-strength Co-free triple-phase Al 10 Cr 12 Fe 35 Mn 23 Ni 20 high-entropy alloy (HEA) was successfully fabricated using Friction Surface Layer Deposition (FSLD), a bulk manufacturing method. Multiple single-layer deposits were produced by varying forging force (F) and traverse speeds (T r ) to optimize the process parameters. The optimized conditions (F = 40 kN & T r = 200 mm/min) were then applied to manufacture a scaled-up multi-layer specimen. The initial microstructure of the HEA consisted of coarse grains of the soft FCC-phase, long columnar dendrites of the hard BCC-phase, and small precipitates of the harder B2-phase within the BCC-dendrites. During FSLD, the FCC-matrix underwent continuous dynamic recrystallization due to high-temperature severe plastic deformation, forming finer equiaxed grains. Simultaneously, the BCC-dendrites fractured into smaller fragments, some of which experienced partial growth and coarsening under applied stress, resulting in an hourglass morphology. In contrast, the small B2-precipitates within the BCC-fragments dissolved during the elevated temperatures of FSLD and reprecipitated as substantially finer precipitates during continuous cooling post-FSLD. Additionally, the orientation relationships between the FCC and BCC/B2 phases were completely destroyed by the severe thermoplastic deformation inherent to FSLD. The microstructural refinements led to a substantial improvement in hardness from 177 HV to 283 HV, driven by Hall-Petch strengthening. The increased number of interfaces, including coherent BCC-B2 interfaces, potentially enhances the sink strength and radiation tolerance of the HEA, making it a promising candidate for nuclear applications. In conclusion, this study also highlights FSLD as a versatile technique for achieving tunable properties in HEAs, with detailed schematics illustrating the complex mechanisms of phase transformations during processing.

Additive Manufacturing↗
DOE OSTI2022

Formation of carbon and oxygen rich surface layer on high purity magnesium by atmospheric carbon dioxide plasma

Carbon and oxygen-rich corrosion barrier layer formed on Mg by a simple and scalable CO 2 atmospheric plasma (CO 2 -AP) process. The reactive CO 2 -AP interacts with the Mg surface and forms a unique layered structure with the top MgCO 3 /MgO-intermixed particulates pillars and the bottom dense layer. The surface features were simultaneously formed on the nano-/micro-structured MgO layer by carbonate molecules, plasma-active CO 2 molecules, and/or other volatile organic compounds on the nano-/micro-structured MgO particle layer. The resulting surfaces after CO 2 -AP were either hydrophobic or hydrophilic and exhibited lower anodic current or high resistance for Mg corrosion. For the hydrophobic surfaces of CO 2 -AP treated Mg, molecular dynamic simulations were performed to understand the origin of hydrophobicity and identified that the amorphous carbon layers formed on the Mg surface are the source. The environmentally benign abundant-gas-based process enables the cost reduction associated with waste treatment, generation of by-product, and supply of raw material.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Measurement of the O-18 to O-16 isotope ratio for characterizing oxide surface layers on LDEF samples

The ratio of the density of the oxygen 18 isotope (O-18) to the density of the oxygen 16 isotope (O-16) is a strong function of altitude in the atmosphere because of the stronger gravitational attraction on the heavier isotope. It is proposed that the measurement of this ratio for oxide surface layers on LDEF samples can easily distinguish oxides formed in orbit from contaminative oxides formed during retrieval procedures. Since the satellite altitude is known as a function of time, it may be possible to use the measured ratio to determine the time of formation of oxide layers, the accuracy depending upon the stability of the atmosphere.

Sagalyn, Paul L.↗
NASA NTRS1973

Modeling of turbulent transport in the surface layer

The turbulence equations as written by Donaldson using the method of invariant modeling have been applied to the following limiting cases of the surface or constant flux layer of the planetary boundary layer: (1) Neutrally stable; (2) stable (above influence of surface roughness); (3) nearly neutrally stable; and (4) very unstable (free convection). For the neutrally stable case, the equations are shown to admit as a solution the familiar logarithmic profile. By use of this result, boundary conditions suitable for the surface layer are defined and are simple to apply to rough surfaces.

Smith, G. L.↗
DOE OSTI2023

Merging flux-variance with surface renewal methods in the roughness sublayer and the atmospheric surface layer

In this article, Two micrometeorological methods utilizing high-frequency sampled air temperature were tested against eddy covariance (EC) sensible heat flux (𝐻) measurements at three sites representing agricultural, agro-forestry, and forestry systems. The two methods cover conventional and newly proposed forms of the flux-variance (FV) and surface renewal (SR) schemes of differing complexities. The sites represent measurements in surface, roughness, and roughness to surface transitional layers. Regression analyzes against EC show that the most reliable FV and SR forms estimate 𝐻 with slopes within ±10% from unity and coefficient of determination 𝑅2 > 0.9 across all the three sites. The best performance of both FV and SR was found at the agricultural site with measurements well within the surface layer, while the worst was found for the tall forest with measurements within the roughness sublayer where its thickness needed to be additionally estimated. The main variable driving 𝐻 in FV is the temperature variance, whereas in SR, it is the geometry of ramp-like structures. Since these structures are also responsible for most of the temperature variance, a novel FV-SR approach emerging from combining the methods is proposed and evaluated against EC measurements and conventional FV and SR schemes. The proposed FV-SR approach requiring only a single fast response thermocouple is potentially independent of calibration and ameliorates some of the theoretical objections that arise when combining ramp statistics with similarity arguments. The combination of methods also provides new insights into the contribution of coherent structures to the temperature variance and its dependence on atmospheric stratification. Other potential utility of the new method is to include it in multi-tool assessments of surface energy fluxes, since a convergence or divergence of the results has a high diagnostic value.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1991

Measurement of the O18 to O16 isotope ratio for characterizing oxide surface layers on LDEF samples

Calculations indicate that measurement of the O-16 to O-18 isotope ratio in oxide layers formed on the surfaces of the Long Duration Exposure Facility (LDEF) samples would provide a powerful tool for distinguishing between layers formed at high altitudes and layers formed at low altitudes, as for example during the retrieval of a satellite. In principle, this ratio may be used to date the formation of the oxide layers.

Sagalyn, Paul L.↗
NASA NTRS1996

Leaf Area Influence on Surface Layer in a Deciduous Forest: Site Description - Part I

A study over a deciduous forest located in middle Massachusetts (USA) has been performed to examine the role of leaves in the forest-atmosphere interaction. Due to the seasonal presence of leaves, a deciduous forest is a 'good laboratory' to study this interaction. In this first part, a description of a 30 m micrometeorological tower as well a qualitative description of some meteorological parameters are presented. The presence of leaves affects the forest in several ways. There is a decrease of upward PAR (Photosynthetically Active Radiation) due to absorption of visible light in the canopy. Water vapor concentration increases, and the CO2 concentration decreases in the surface layer as the canopy starts to be foliated. The physical presence of the leaves is felt in other quantities such as the global albedo and the subcanopy environment.

Sakai, Ricardo K.↗
DOE OSTI2026

Modulation induced by very-large-scale motions on the inclination angle of wall-attached eddies: an atmospheric surface layer experiment

The forward leaning inclination angle, 𝛾, of coherent turbulent structures is a well-known feature of wall-bounded turbulent flows. Although invariant across friction Reynolds numbers within the range 𝑅𝑒 𝜏 =10 3 −10 6 , 𝛾 can vary significantly across turbulent scales within a high-Reynolds-number flow. Very-large-scale motions (VLSMs) are known to induce significant changes in the instantaneous shear profile, which is a conditioning event that could trigger variability in the inclination angle of smaller coherent turbulent structures. Although this aspect has been extensively studied via numerical and laboratory experiments, few studies have explored this feature for a very-high-Reynolds-number atmospheric flow. In this work, the inclination angle of turbulent structures within the atmospheric surface layer at a very high Reynolds number (𝑅𝑒 𝜏 =7.9 ×10 5 ) is investigated by deploying a scanning Doppler light detection and ranging and a super large particle image velocimetry (SLPIV) apparatus. The inclination angle of wall-attached eddies is inferred either from the two-point correlation of streamwise velocity (𝛾 =41.1∘) or with a scale-dependent approach through the spectral linear stochastic estimator (SLSE). The SLSE (and, thus, the scale-dependent inclination angle) is conditionally evaluated based on the high- and low-momentum events induced by VLSMs, both in the streamwise (𝑢′𝑉𝐿𝑆𝑀) and in the vertical (𝑤′ 𝑉𝐿𝑆𝑀) velocity components. As a result, lower inclination angles (𝛾 =30° −50°) are found for 𝑢$^{'}_{VLSM}$ >0 (𝑤$^{'}_{VLSM}$ <0), while higher values (50° −85°) are ascribed to 𝑢$^{'}_{VLSM}$ <0 (𝑤$^{'}_{VLSM}$ >0). This result emphasises the primary role that VLSMs play in shaping the wall-attached eddy geometry, which, in turn, is crucial to determine the Reynolds stress balance within the wall-attached eddy range.

42 ENGINEERING↗
DOE OSTI2023

Logarithmic scaling of higher-order temperature moments in the atmospheric surface layer

A generalized logarithmic law for high-order moments of homogeneous passive scalars is proposed for turbulent boundary layers. This law is analogous to the generalized log law that has been proposed for high-order moments of the turbulent longitudinal velocity and is derived by combining the random sweeping decorrelation hypothesis with a spectral model informed by the attached eddy hypothesis. The proposed theory predicts that the high-order moments of passive scalar fluctuations within the inertial sublayer will vary logarithmically with wall-normal distance (), and is evaluated using high frequency time-series measurements of temperature and streamwise velocity fluctuations obtained in the first meter of the atmospheric surface layer (ASL) under near-neutral thermal stratification. The logarithmic dependence with within the inertial sublayer is observed in both the air temperature and velocity moments, with good agreement to the predictions from the proposed theory. Surprisingly, the proposed theory appears to be as, if not more, valid for transported passive scalars than for the longitudinal velocity.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1995

Magnetic Or Optical Surface Layer Would Indicate Strain

In proposed method of obtaining information on strain at surface of material specimen, magnetic coat (like that on magnetic tape) or optical coat (like that on compact disk) applied to all or part of surface monitored. Coating layer and associated measuring equipment, taken together, constitute system called "material strain monitor" (MSM). MSM important in research in materials and mechanics; in particular, expected to compete strongly with systems based on image-analysis and laser techniques now being developed to obtain information on strain fields.

Heyman, Joseph S.↗
NASA NTRS1979

Formation of porous surface layers in reaction bonded silicon nitride during processing

An effort was undertaken to determine if the formation of the generally observed layer of large porosity adjacent to the as-nitride surfaces of reaction bonded silicon nitrides could be prevented during processing. Isostatically pressed test bars were prepared from wet vibratory milled Si powder. Sintering and nitriding were each done under three different conditions:(1) bars directly exposed to the furnance atmosphere; (2) bars packed in Si powder; (3) bars packed in Si3N4 powder. Packing the bars in either Si of Si3N4 powder during sintering retarded formation of the layer of large porosity. Only packing the bars in Si prevented formation of the layer during nitridation. The strongest bars (316 MPa) were those sintered in Si and nitrided in Si3N4 despite their having a layer of large surface porosity; failure initiated at very large pores and inclusions. The alpha/beta ratio was found to be directly proportional to the oxygen content; a possible explanation for this relationship is discussed.

Shaw, N. J.↗