Search NASA⌕ Search

SEARCH · Search NASA

Results for “SWEEP FREQUENCY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Low Frequency Waves in the Plasma Environment Around the Shuttle

As a part of the SAMPIE (The Solar Array Module Plasma Interaction Experiment) program, the Langmuir probe (LP) was employed to measure plasma characteristics during the flight of STS-62. The whole set of data could be divided into two parts: (1) low frequency sweeps to determine voltage-current characteristics and to find the electron temperature and number density; (2) high frequency turbulence (HFT) data caused by electromagnetic noise around the Shuttle. Broadband noise was observed at 250-20,000 Hz frequencies. Measurements were performed in ram conditions; thus, it seems reasonable to believe that the influence of spacecraft operations on plasma parameters was minimized. It is shown that ion acoustic waves were observed, and two kinds of instabilities are suggested for explanation of the origin of these waves. According to the purposes of SAMPIE, samples of solar cells were placed in the cargo bay of the Shuttle, and high negative bias voltages were applied to them to initiate arcing between these cells and the surrounding plasma. The arcing onset was registered by special counters, and data were obtained that included the amplitudes of current, duration of each arc, and the number of arcs per one experiment. The LP data were analyzed for two different situations: with arcing and without arcing. Electrostatic noise spectra for both situations and a theoretical explanation of the observed features are presented in this paper.

Vayner, Boris V.↗
NASA NTRS1998

A Methodology for Flight-Time Identification of Helicopter-Slung Load Frequency Response Characteristics Using CIFER

Helicopter slung load operations are common in both military and civil contexts. The slung load adds load rigid body modes, sling stretching, and load aerodynamics to the system dynamics, which can degrade system stability and handling qualities, and reduce the operating envelope of the combined system below that of the helicopter alone. Further, the effects of the load on system dynamics vary significantly among the large range of loads, slings, and flight conditions that a utility helicopter will encounter in its operating life. In this context, military helicopters and loads are often qualified for slung load operations via flight tests which can be time consuming and expensive. One way to reduce the cost and time required to carry out these tests and generate quantitative data more readily is to provide an efficient method for analysis during the flight, so that numerous test points can be evaluated in a single flight test, with evaluations performed in near real time following each test point and prior to clearing the aircraft to the next point. Methodology for this was implemented at Ames and demonstrated in slung load flight tests in 1997 and was improved for additional flight tests in 1999. The parameters of interest for the slung load tests are aircraft handling qualities parameters (bandwidth and phase delay), stability margins (gain and phase margin), and load pendulum roots (damping and natural frequency). A procedure for the identification of these parameters from frequency sweep data was defined using the CIFER software package. CIFER is a comprehensive interactive package of utilities for frequency domain analysis previously developed at Ames for aeronautical flight test applications. It has been widely used in the US on a variety of aircraft, including some primitive flight time analysis applications.

Sahai, Ranjana↗
NASA NTRS2004

Selected Flight Test Results for Online Learning Neural Network-Based Flight Control System

The NASA F-15 Intelligent Flight Control System project team developed a series of flight control concepts designed to demonstrate neural network-based adaptive controller benefits, with the objective to develop and flight-test control systems using neural network technology to optimize aircraft performance under nominal conditions and stabilize the aircraft under failure conditions. This report presents flight-test results for an adaptive controller using stability and control derivative values from an online learning neural network. A dynamic cell structure neural network is used in conjunction with a real-time parameter identification algorithm to estimate aerodynamic stability and control derivative increments to baseline aerodynamic derivatives in flight. This open-loop flight test set was performed in preparation for a future phase in which the learning neural network and parameter identification algorithm output would provide the flight controller with aerodynamic stability and control derivative updates in near real time. Two flight maneuvers are analyzed - pitch frequency sweep and automated flight-test maneuver designed to optimally excite the parameter identification algorithm in all axes. Frequency responses generated from flight data are compared to those obtained from nonlinear simulation runs. Flight data examination shows that addition of flight-identified aerodynamic derivative increments into the simulation improved aircraft pitch handling qualities.

Williams-Hayes, Peggy S.↗
NASA NTRS1988

Striated spectral activity in Jovian and Saturnian radio emission

Examination of high time resolution frequency-time spectrograms of radio emission measured near the Voyager 1 and 2 encounters with Jupiter reveals occasional striation patterns within the normally diffuse hectometric radiation. The patterns are characterized by distinctive banded structures of enhanced intensity meandering in frequency over time scales of minutes to tens of minutes. This banded form of striated spectral activity (SSA) has an occurrence probability of the order of 5 percent during the three weeks before and after Jupiter encounters. Plots of single 6-s frequency sweeps often exhibit a slow rise in intensity followed by a sharp drop-off in each band as frequency decreases. Banded SSA is often preceded or followed by chaotic SSA in which banding of the emission becomes discontinuous or unrecognizable, although the intensity modulation is still evident. Although SSA normally occurs in the frequency range of roughly 0.2-1.0 MHz, similar but longer-lasting patterns have been found occasionally in decametric emission above 10 MHz. Analogous modulation has also been observed in the Saturnian radio emission, suggesting that SSA may be a common feature intrinsic to the radio emission at both planets.

Thieman, James R.↗
NASA NTRS2004

Selected Flight Test Results for Online Learning Neural Network-Based Flight Control System

The NASA F-15 Intelligent Flight Control System project team has developed a series of flight control concepts designed to demonstrate the benefits of a neural network-based adaptive controller. The objective of the team is to develop and flight-test control systems that use neural network technology to optimize the performance of the aircraft under nominal conditions as well as stabilize the aircraft under failure conditions. Failure conditions include locked or failed control surfaces as well as unforeseen damage that might occur to the aircraft in flight. This report presents flight-test results for an adaptive controller using stability and control derivative values from an online learning neural network. A dynamic cell structure neural network is used in conjunction with a real-time parameter identification algorithm to estimate aerodynamic stability and control derivative increments to the baseline aerodynamic derivatives in flight. This set of open-loop flight tests was performed in preparation for a future phase of flights in which the learning neural network and parameter identification algorithm output would provide the flight controller with aerodynamic stability and control derivative updates in near real time. Two flight maneuvers are analyzed a pitch frequency sweep and an automated flight-test maneuver designed to optimally excite the parameter identification algorithm in all axes. Frequency responses generated from flight data are compared to those obtained from nonlinear simulation runs. An examination of flight data shows that addition of the flight-identified aerodynamic derivative increments into the simulation improved the pitch handling qualities of the aircraft.

Williams, Peggy S.↗
NASA NTRS1990

Acquisition of the QPSK demodulator in the presence of interference

The acquisition behavior of the tracking and data relay satellite system (TDRSS) receiver (a quadrative phase-shift keying (QPSK) demodulator using a dither lock detector) in the presence of interference from another user has been analyzed using a simulation model. The demodulator is composed of an automatic gain control, a QPSK Costas loop, a frequency sweep unit, lock test units, and a control unit. The simulation model has been tested for the following variables: signal and interference Doppler frequencies and phase offsets (with respect to initial voltage control oscillator setup), signal-to-interference ratio (SIR), and signal I/Q power ratio. The simulation results are discussed.

Ghazvinian, Farzad↗
DOE OSTI2025

Leveraging FPGA Advantages for Quicker Data Processing for LBNF

The Long Baseline Neutrino Facility (LBNF) will deliver a 2.4 MW muon neutrino beam from Fermilab to the Deep Underground Neutrino Experiment (DUNE), requiring unprecedented precision in beamline alignment to achieve DUNE's neutrino oscillation measurement goals. Vertical misalignments of beamline components as small as 0.5 mm can contribute 6-7\% uncertainty in predicted neutrino flux, necessitating sub-0.1 mm alignment monitoring capabilities. The Horn Location Sensor (HLS) system employs frequency sweep interferometry (FSI) in a distributed hydrostatic leveling network to achieve the required precision under harsh radiation conditions up to 5000 kRad/year. Traditional FSI implementations suffer from laser sweep nonlinearities that degrade resolution and require computationally intensive post-processing corrections using gas reference cells. This work presents a real-time FPGA-based implementation of the HLS data acquisition and processing system using a sweep tracker interferometer for dynamic sweep linearization. The system utilizes a PYNQ-Z2 FPGA with programmable logic implementing parallel 16k-point FFT processing across four channels, synchronized by the sweep tracker signal to eliminate post-processing requirements. Spectral performance testing demonstrates significant improvements in peak sharpness compared to traditional fixed-frequency digitization. The FPGA implementation enables real-time displacement monitoring with processing speeds orders of magnitude faster than software-based approaches, essential for the operational requirements of LBNF's eventual distributed sensor network. This advancement in real-time FSI processing directly supports DUNE's precision neutrino physics program by providing the rapid feedback necessary for maintaining stringent beamline alignment tolerances during high-power beam operations.

Rossel, Jacob↗
DOE OSTI2019

Simultaneous mode locking and Q-switching in a solid-state laser with a travelling-wave acousto-optic modulator and retroreflector

This paper presents a numerical study of the dynamics of a mode-locked, Q-switched laser whose cavity contains a travelling-wave acousto-optic modulator (AOM) and a retroreflector which returns the zeroth- and first-order diffracted waves to the AOM. The reflectivity of the retroreflector depends on the order of diffraction. If the AOM is switched on once or periodically, lasing is characterised by a pulse train frequency sweep. Keeping the AOM constantly switched on leads to self-oscillations. Their characteristics can be controlled by varying the detuning of the operating frequency of the modulator from resonance. (paper)

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1989

Structural stability augmentation system design using BODEDIRECT: A quick and accurate approach

A methodology is presented for a modal suppression control law design using flight test data instead of mathematical models to obtain the required gain and phase information about the flexible airplane. This approach is referred to as BODEDIRECT. The purpose of the BODEDIRECT program is to provide a method of analyzing the modal phase relationships measured directly from the airplane. These measurements can be achieved with a frequency sweep at the control surface input while measuring the outputs of interest. The measured Bode-models can be used directly for analysis in the frequency domain, and for control law design. Besides providing a more accurate representation for the system inputs and outputs of interest, this method is quick and relatively inexpensive. To date, the BODEDIRECT program has been tested and verified for computational integrity. Its capabilities include calculation of series, parallel and loop closure connections between Bode-model representations. System PSD, together with gain and phase margins of stability may be calculated for successive loop closures of multi-input/multi-output systems. Current plans include extensive flight testing to obtain a Bode-model representation of a commercial aircraft for design of a structural stability augmentation system.

Goslin, T. J.↗
NASA NTRS1998

Galileo Direction Finding of Jovian Radio Emissions

The Galileo spacecraft, in orbit about Jupiter, has observed distinct spin modulation of plasma wave emissions near the Ganymede (G1 and G2) encounters in the frequency range from about 100 kHz to approximately 6 MHz. Assuming circularly polarized, transverse electromagnetic radiation, we have used the spin modulation of the sweep-frequency receivers of the electric dipole antenna over many spins to estimate the source location in the spin plane of the spacecraft. Hectometric (HOM) and decametric (DAM) emission is observed by Galileo as a general and continuous background with frequent bursts that last tens of minutes and can be separated by minutes or hours. We have analyzed HOM and DAM emissions observed near Jupiter just after the GI and G2 encounters, including two HOM/DAM "arc" signatures observed after the G2 encounter. These latter appear to be low-frequency extensions of DAM arcs, with source regions along either the Io or the Ganymede flux tube. While the uncertainties associated with the data analysis do not allow a precise source location, the HOM/DAM emission observed near the G1 and G2 encounters is consistent with a gyroresonant source region, but it is necessary to require refraction due to the Io torus to understand the results. To explain emission from apparent source regions above a gyroresonant source region, wave refraction from asymmetries in the Io plasma torus that extend along magnetic field lines is postulated. Alternatively, if such torus density asymmetries do not exist, emission with sources above a gyroresonant source region would require another free-energy source such as energetic plasma beams in the presence of density gradients or temperature anisotropies.

Menietti, J. D.↗
NASA NTRS1987

Frequency stabilization in injection controlled pulsed CO2 lasers

Longitudinal mode selection by injection has been demonstrated as a viable technique for tailoring a TEA-CO2 laser with pulse energies of a Joule or greater to fit the requirements of a coherent lidar transmitter. Once reliable generation of single-longitudinal-mode (SLM) pulses is obtained, one can study the intrapulse frequency variation and attempt to determine the sources of frequency sweeping, or chirp. These sources include the effect of the decaying plasma, the thermal gradient due to the energy dissipation associated with the laser mechanism itself, and the pressure shift of the center frequency of the laser transition. The use of the positive-branch unstable resonator as an efficient means of coupling a discharge with transverse spatial dimensions of the order of centimeters to an optical cavity mode introduces another concern: namely, what can be done to emphasize transverse mode discrimination in an unstable resonator cavity while maintaining high coupling efficiency. These issues are briefly discussed in the paper, and representative experimental examples are included.

Menzies, Robert T.↗
NASA NTRS1978

Swept group delay measurement

Direct recording of group delay measurements on a system under temperature and stress tests employs modulated carrier frequency sweep over an S or X band. Reference path and test paths to separate detectors utilize a power divider e.g., a directional coupler or a hybrid T junction. An initially balanced phase comparator is swept in frequency by modulated carrier over the band of interest for different conditions of temperature and/or mechanical stress to obtain characteristic group delay curves.

Trowbridge, D. L.↗
DOE OSTI2019

Modification of the Alfvén wave spectrum by pellet injection

Alfvén eigenmodes driven by energetic particles are routinely observed in tokamak plasmas. These modes consist of poloidal harmonics of shear Alfvén waves coupled by inhomogeneity in the magnetic field. In this work, further coupling is introduced by 3D inhomogeneities in the ion density during the assimilation of injected pellets. This additional coupling modifies the Alfvén continuum and discrete eigenmode spectrum. We find that the frequencies of Alfvén eigenmodes drop dramatically when a pellet is injected in JET. From these observations, information about the changes in the ion density caused by a pellet can be inferred. To use Alfvén eigenmodes for MHD spectroscopy of pellet injected plasmas, the 3D MHD codes Stellgap and AE3D were generalised to incorporate 3D density profiles. Additionally, a model for the expansion of the ionised pellet plasmoid along a magnetic field line was derived from the fluid equations. Thereby, the time evolution of the Alfvén eigenfrequency is reproduced. By comparing the numerical frequency drop of a toroidal Alfvén eigenmode (TAE) to experimental observations, the initial ion density of a cigar-shaped ablation region of length 4 cm is estimated to be n * =6.8×10 22 m -3 at the TAE location (r/a≈0.75). The frequency sweeping of an Alfvén eigenmode ends when the ion density homogenises poloidally. Modelling suggests that the time for poloidal homogenisation of the ion density at the TAE position is τ h =18±4 ms for inboard pellet injection, and τ h =26±2 ms for outboard pellet injection. By reproducing the frequency evolution of the elliptical Alfvén eigenmode (EAE), the initial ion density at the EAE location (r/a≈0.9) can be estimated to be n * =4.8×10 22 m -3 . Poloidal homogenisation of the ion density takes 2.7 times longer at the EAE location than at the TAE location for both inboard and outboard pellet injection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1980

Single-stage electrohydraulic servosystem for actuating on airflow valve with frequencies to 500 hertz

An airflow valve and its electrohydraulic actuation servosystem are described. The servosystem uses a high-power, single-stage servovalve to obtain a dynamic response beyond that of systems designed with conventional two-stage servovalves. The electrohydraulic servosystem is analyzed and the limitations imposed on system performance by such nonlinearities as signal saturations and power limitations are discussed. Descriptions of the mechanical design concepts and developmental considerations are included. Dynamic data, in the form of sweep-frequency test results, are presented and comparison with analytical results obtained with an analog computer model is made.

Webb, J. A., Jr.↗
NASA NTRS1995

Gravitational radiation from rapidly rotating nascent neutron stars

We study the secular evolution and gravitational wave signature of a newly formed, rapidly rotating neutron star. The neutron star may arise from core collapse in a massive star or from the accretion-induced collapse of a white dwarf. After a brief dynamical phase, the nascent neutron star settles into an axisymmetric, secularly unstable state. Gravitational radiation drives the star to a nonaxisymmetric, stationary equilibrium configuration via the bar-mode instability. The emitted quasi-periodic gravitational waves have a unique signature: the wave frequency sweeps downward from a few hundred Hertz to zero, while the wave amplitude increase from zero to a maximum and then decays back to zero. Such a wave signal could detected by broadband gravitational wave interferometers currently being constructed. We also characterize two other types of gravitational wave signals that could arise in principle from a rapidly rotating, secularly unstable neutron star: a high-frequency (f greater than or approximately = 1000 Hz) wave which increases the pattern-speed of the star, and a wave that actually increases the angular momentum of the star.

Lai, Dong↗
DOE OSTI2025

Detecting isolated resonance curves using fixed frequency voltage control tests

Isolated resonance curves, or isolas, are resonance branches of the harmonically forced system that exist separately from the main nonlinear forced response curve, leading to excessive vibrations. Traditional stepped or swept sine simulations and tests rely on continuation along the frequency parameter, typically resulting in a jump phenomenon along the primary resonance branch, prior to the disconnected isola. The main objective of this research is to propose an approach to identify isolated resonance curves by performing continuation along the input amplitude that initializes the response from a low-amplitude solution in the linear regime. Furthermore, this is achieved with the open-loop fixed frequency voltage control method that continues along the shaker voltage parameter and measures the so-called S-curves, which are theoretically a continuous solution branch that connect to the isola. The methodology is demonstrated on a fixture-wing-pylon assembly with a vibro-impact nonlinearity localized in a pylon subcomponent attachment. Multi-harmonic balance simulations are deployed to compute both the nonlinear forced response curves and S-curves to demonstrate the isola detection strategy on a reduced-order finite element model of the nonlinear system. Swept sine and fixed frequency voltage control tests are then conducted on the physical structure to demonstrate the isola detection experimentally, revealing the existence of the large amplitude vibrations that are undetected in the forces levels and frequencies measured with traditional frequency sweeping.

Characterization and Analytical Technique↗
DOE OSTI2024

Numerical simulation of RHIC polarized proton run 17 spin flipper experiments

RHIC nine-magnet spin flipper has been operated successfully during RHIC polarized proton Run 17, with 97% spin flip efficiency achieved. The results show the importance of mirror resonance removal, small spin tune spread, and proper spin flipper driving tune sweep speed. Detailed spin tracking simulations, based on a Lorentz force and Thomas-BMT differential equation numerical solver code for accuracy, have been carried out to understand the experimental results. Agreement within measurement accuracy is obtained at injection energy, 23.8 GeV. It is not as tight at 255 GeV, reasons for that are exposed. These measurements and numerical studies allow to determine the sensitivity of spin-flip efficiency to the dispersion slopes at the two Siberian snakes and to the ac dipole frequency sweep speed. They also provide guidance for future developments at BNL’s electron-ion collider. Published by the American Physical Society 2024

43 PARTICLE ACCELERATORS↗
NASA NTRS2009

Synthesis of Submillimeter Radiation for Spectroscopy

The frequency-multiplier submillimeter spectrometer (FMSS) is a laboratory apparatus for far-infrared molecular spectroscopy, embodying several advances over prior such apparatuses. The most innovative part of the FMSS is a source of monochromatic submillimeter- wavelength radiation that can be tuned over a wide frequency range, as needed for trace gas analyses and molecular- structure studies for which such apparatuses are typically used. The radiation source features a modular design and is built mostly from commercially available components. It includes a computer-controlled radio-frequency synthesizer, amplifiers, and frequency multipliers of a type heretofore used in local oscillators for heterodyne far-infrared receivers. In conjunction with the rest of the apparatus, this source makes it possible to perform measurements over large portions of the submillimeter-wavelength spectrum with resolution, accuracy, and sensitivity greater than those achievable in Fourier-transform infrared spectroscopy. In comparison with prior laboratory submillimeter- wavelength radiation sources, this source is much lighter in weight, less cumbersome, less power-hungry, and capable of sustained operation with less intervention by laboratory personnel. Also, unlike some prior submillimeter-wavelength sources, this source does not require a high-voltage power source. As shown in more detail in the figure, the radiation source includes a sweep frequency synthesizer connected to an external waveform generator, the output of which is used as a reference signal. The synthesizer is computer-controlled through a standard general-purpose interface bus (GPIB) and is operated in phase-locked continuous- wave mode for all measurements. The synthesizer output ranges in frequency from 11 to 18 GHz. For suppression of frequency spurs and harmonics, the output of the frequency synthesizer is fed through a tunable yttrium iron garnet (YIG) filter, which is swept in frequency simultaneously with the frequency synthesizer.

Maiwald, Frank↗