Results for “Safety Performance Indicators” — Page 4

NASA NTRSDate not supplied

System Safety Analysis of Complex NASA Systems with Model-Based Engineering (REV B)

The emergence of model-based engineering is transforming design and analysis methodologies. A recognized benefit of model-based engineering is the existence of a “single source of truth” about the system that becomes the authoritative source of data and information for designers, analysts, and developers. This promotes consistency and efficiency as the design emerges and can be used to further optimize the design. Integrating System Safety Engineers to the “single source of truth” will ensure that the outputs of their assessments and analyses are relevant to the design as it evolves. Use of an integrated system model enables near immediate evaluation of a design change as well as development of operational processes for risk assessment and communication. Such models can enable efficient and timely analysis of system hazards (e.g., hazard fault tree analysis and procedure simulations) and produce complete, accurate, and more consistent products (e.g., hazard reports and safety requirement evaluations). Therefore, an agency-sponsored team at Goddard Space Flight Center (GSFC) recently completed a System Safety Study of modeling and testing capabilities as part of a Model-Based Safety and Mission Assurance Initiative (MBSMAI). Using an existing model developed for reliability analyses, GSFC modeling and system safety experts performed system safety analysis/modeling and produced safety products. The team evaluated model-based feasibility to support System Safety Engineering, developed safety analysis modeling processes, and identified tool capability advancement/development needs. These study results indicate model-based engineering is valid and useable for System Safety Engineering for NASA if adequate modeling processes and environment are established.

NASA↗

NASA NTRS1975

Evaluation of class 2 biological cabinets

Basic investigations, consisting primarily of airflow measurements and visual smoke tests, were made on four commercially available units. The results indicated that performance varied considerably between units. Therefore, it was decided to outline the performance desired and to include in the overall equipment specifications a set of performance tests to assure a clean air safety cabinet with respect to chemical usage. The evaluation was to be based on aerodynamic performance under the various modes of operation.

Chamberlin, R. E.↗

NASA NTRS1991

Autonomous guidance, navigation and control bridging program plan

A four-center NASA team has undertaken to develop and demonstrate mature technologies applicable to autonomous guidance, navigation, and control (GNC) systems for application to the National Space Transportation System in full cognizance of its operational, safety, and performance requirements, as well as its cost constraints. Attention is to be given to GNC launch/landing weather assessment, ascent guidance, ascent load relief, and system failure during ascent. Preliminary results indicate that a ground-computed atmospheric steering profile can achieve near-optimum performance as well as high cost effectiveness.

Mcswain, G. G.↗

NASA NTRS1976

Guidelines for advanced manned space vehicle program, June 1960

A very broad mission objective was established; i.e., manned circumlunar flight and return to earth. It is implicit that the Saturn will be the primary propulsion system for this mission. The following attempts to: (1) define the objective so as to achieve as much capability in the vehicle as possible; (2) draw on Mercury experience to provide broad guidelines for vehicle performance and safety; (3) provide flexibility in the vehicle capability in the event that the manned lunar mission is proved to be subject to unacceptable risk in the target time period; and (4) indicate problem areas where work appears to be particularly needed.

Gilruth, R. R.↗

NASA NTRS2016

Task Demand Variation in Air Traffic Control: Implications for Workload, Fatigue, and Performance

In air traffic control, task demand and workload have important implications for the safety and efficiency of air traffic, and remain dominant considerations. Within air traffic control, task demand is dynamic. However, research on demand transitions and subsequent controller perception and performance is limited. This research uses an air traffic control simulation to investigate the effect of task demand transitions, and the direction of those transitions, on workload and fatigue and one efficiency performance measure. Results indicate that a change in task demand appears to affect both workload and fatigue ratings, although not necessarily performance. In addition, participants' workload and fatigue ratings in equivalent task demand periods appear to change depending on the demand period preceding the time of the current ratings. Further research is needed to enhance understanding of demand transition and workload history effects on operator experience and performance, in both air traffic control and other safety-critical domains.

workload history↗

NASA NTRS2016

Task Demand Variation in Air Traffic Control: Implications for Controller Workload, Fatigue, and Performance

In air traffic control, task demand and workload have important implications for the safety and efficiency of air traffic, and remain dominant considerations. Within air traffic control, task demand is dynamic. However, research on demand transitions and subsequent controller perception and performance is limited. This research uses an air traffic control simulation to investigate the effect of task demand transitions, and the direction of those transitions, on workload and fatigue and one efficiency performance measure. Results indicate that a change in task demand appears to affect both workload and fatigue ratings, although not necessarily performance. In addition, participants workload and fatigue ratings in equivalent task demand periods appear to change depending on the demand period preceding the time of the current ratings. Further research is needed to enhance understanding of demand transition and workload history effects on operator experience and performance, in both air traffic control and other safety-critical domains.

workload history↗

NASA NTRS2014

Space Mission Human Reliability Analysis (HRA) Project

The purpose of the Space Mission Human Reliability Analysis (HRA) Project is to extend current ground-based HRA risk prediction techniques to a long-duration, space-based tool. Ground-based HRA methodology has been shown to be a reasonable tool for short-duration space missions, such as Space Shuttle and lunar fly-bys. However, longer-duration deep-space missions, such as asteroid and Mars missions, will require the crew to be in space for as long as 400 to 900 day missions with periods of extended autonomy and self-sufficiency. Current indications show higher risk due to fatigue, physiological effects due to extended low gravity environments, and others, may impact HRA predictions. For this project, Safety & Mission Assurance (S&MA) will work with Human Health & Performance (HH&P) to establish what is currently used to assess human reliabiilty for human space programs, identify human performance factors that may be sensitive to long duration space flight, collect available historical data, and update current tools to account for performance shaping factors believed to be important to such missions. This effort will also contribute data to the Human Performance Data Repository and influence the Space Human Factors Engineering research risks and gaps (part of the HRP Program). An accurate risk predictor mitigates Loss of Crew (LOC) and Loss of Mission (LOM).The end result will be an updated HRA model that can effectively predict risk on long-duration missions.

Boyer, Roger↗

NASA NTRS1986

Oxygen/hydrogen Space Station propulsion system concept definition for IOC

The potential for the reduction in propulsion system life cycle costs through the use of on-board water electrolysis to generate oxygen and hydrogen propellants, as well as the potential advantages of improved system safety and contamination impact, led to a study to evaluate candidate oxygen-/hydrogen-based propulsion systems. In this study a representative set of propulsion system requirements were compiled and candidate oxygen/hydrogen-based propulsion systems synthesized. These candidate concepts were screened and a systems evaluation was performed on the remaining eight candidate concepts. Detailed system schematics were prepared. Operational design conditions were determined and system weight, volume, energy requirements, and costs were calculated. Evaluation results indicated that the oxygen/hydrogen propulsion systems can provide simple, low cost, and viable systems for the IOC Space Station. Based on these data, a relative concept evaluation was conducted using as selection criteria reliability, safety, cost, technical risk, contamination, operational utility, growth potential, and integration potential. Top ranked candidate systems were recommended to NASA/MSFC for consideration for the IOC Space Station.

Shoji, J. M.↗

NASA NTRS2005

The Small Aircraft Transportation System Higher Volume Operations (SATS HVO) Flight Experiment

This paper provides a summary of conclusions from the Small Aircraft Transportation System (SATS) Higher Volume Operations (HVO) Flight Experiment which NASA conducted to determine pilot acceptability of the HVO concept for normal conditions. The SATS HVO concept improves efficiency at non-towered, non-radar airports in Instrument Meteorological Conditions (IMC) while achieving a level of safety equal to today s system. Reported are results from flight experiment data that indicate that the SATS HVO concept is viable. The success of the SATS HVO concept is based on acceptable pilot workload, performance, and subjective criteria when compared to the procedural control operations in use today at non-towered, non-radar controlled airfields in IMC. The HVO Flight Experiment, flown on NASA's Cirrus SR22, used a subset of the HVO Simulation Experiment scenarios and evaluation pilots in order to validate the simulation experiment results. HVO and Baseline (today s system) scenarios flown included: single aircraft arriving for a GPS non-precision approach; aircraft arriving for the approach with multiple traffic aircraft; and aircraft arriving for the approach with multiple traffic aircraft and then conducting a missed approach. Results reveal that all twelve low-time instrument-rated pilots preferred SATS HVO when compared to current procedural separation operations. These pilots also flew the HVO procedures safely and proficiently without additional workload in comparison to today s system (Baseline). Detailed results of pilot flight technical error, and their subjective assessments of workload and situation awareness are presented in this paper.

Williams, Daniel M.↗

NASA NTRS1975

The Airfloat HL project

A design study is described for a large low-cost rigid airship intended primarily for the movement of large indivisible loads (cargo) between industrial sites. A survey of the ship and its overall performance is followed by accounts of the operational procedures for the above function and for an alternative application to unit module transfer between fixed terminals. A final section indicates the estimated costs of construction and operation. Safety factors are also considered. Lifting devices such as winches, hoists are shown and described, and airship configurations are also shown.

Mowforth, E.↗

NASA NTRS1975

Astronaut activity

Human factors pertinent to the design and operation of spacecraft are considered. The geometric characteristics of spacecraft that define the degree and type of confinement imposed on the crew and the character of equipment management and housekeeping necessary for hygiene, comfort and safety are discussed. The controls and displays of various spacecraft are described to indicate the degree to which crew functions become integral to functions of the total spacecraft. The contributions of the crew to system reliability and performance are summarized and the increasing significance of the crew's role in scientific observation and experimentation is noted.

Loftus, J. P., Jr.↗

NASA NTRS2023

Software Error Incident Categorizations in Aerospace

Since the first use of computers in space and aircraft, software errors have occurred. These errors can manifest as loss-of-life or less catastrophically. As the demand for automation increases, software in safety-critical systems should be designed to be tolerant to the most likely software faults. This paper categorizes historic aerospace software errors to determine trends of how and where automation is most likely to fail. A distinction between software producing wrong (erroneous) output versus no output (fail-silent) is introduced. Of the historical incidents analyzed, 87% were from software acting unexpectedly rather than simply stopping. Rebooting was found to be ineffective to clear erroneous behavior, and only partially effective for silent software. Errors were traced back to the software logic itself in 62% of cases, 13% within configurable data, and 25% introduced through input. Thirty percent (30%) of unexpected software behavior was caused by the absence of software and 20% was due to “unknown-unknowns”. These findings indicate that to achieve fault tolerance in safety-critical systems, backup strategies must be employed to detect and respond to erroneous software behavior beyond only fail-silent cases, and robust off-nominal testing should be performed to uncover unanticipated situations.

Software↗

NASA NTRS2001

Scintillation Effects on Space Shuttle GPS Data

Irregularities in ionospheric electron density result in variation in amplitude and phase of Global Positioning System (GPS) signals, or scintillation. GPS receivers tracking scintillated signals may lose carrier phase or frequency lock in the case of phase sc intillation. Amplitude scintillation can cause "enhancement" or "fading" of GPS signals and result in loss of lock. Scintillation can occur over the equatorial and polar regions and is a function of location, time of day, season, and solar and geomagnetic activity. Mid latitude regions are affected only very rarely, resulting from highly disturbed auroral events. In the spring of 1998, due to increasing concern about scintillation of GPS signals during the upcoming solar maximum, the Space Shuttle Program began to assess the impact of scintillation on Collins Miniaturized Airborne GPS Receiver (MAGR) units that are to replace Tactical Air Control and Navigation (TACAN) units on the Space Shuttle orbiters. The Shuttle Program must determine if scintillation effects pose a threat to safety of flight and mission success or require procedural and flight rule changes. Flight controllers in Mission Control must understand scintillation effects on GPS to properly diagnose "off nominal" GPS receiver performance. GPS data from recent Space Shuttle missions indicate that the signals tracked by the Shuttle MAGR manifest scintillation. Scintillation is observed as anomalous noise in velocity measurements lasting for up to 20 minutes on Shuttle orbit passes and are not accounted for in the error budget of the MAGR accuracy parameters. These events are typically coincident with latitude and local time occurrence of previously identified equatorial spread F within about 20 degrees of the magnetic equator. The geographic and seasonal history of these events from ground-based observations and a simple theoretical model, which have potential for predicting events for operational purposes, are reviewed.

Goodman, John L.↗

NASA NTRS2008

Ares I-X Upper Stage Simulator Structural Analyses Supporting the NESC Critical Initial Flaw Size Assessment

The structural analyses described in the present report were performed in support of the NASA Engineering and Safety Center (NESC) Critical Initial Flaw Size (CIFS) assessment for the ARES I-X Upper Stage Simulator (USS) common shell segment. The structural analysis effort for the NESC assessment had three thrusts: shell buckling analyses, detailed stress analyses of the single-bolt joint test; and stress analyses of two-segment 10 degree-wedge models for the peak axial tensile running load. Elasto-plastic, large-deformation simulations were performed. Stress analysis results indicated that the stress levels were well below the material yield stress for the bounding axial tensile design load. This report also summarizes the analyses and results from parametric studies on modeling the shell-to-gusset weld, flange-surface mismatch, bolt preload, and washer-bearing-surface modeling. These analyses models were used to generate the stress levels specified for the fatigue crack growth assessment using the design load with a factor of safety.

Knight, Norman F., Jr.↗

NASA NTRS1984

A high energy stage for the National Space Transporation System

The Shuttle/Centaur is an expendable hydrogen/oxygen cryogenic upper stage for use with the National Space Transportation System. It is a modification of the existing Atlas/Centaur which was used by NASA since 1966 to launch interplanetary and Earth orbital payloads for numerous organizations. Two configurations of the Shuttle/Centaur are being developed. Vehicle capability includes placing approximately 4500 kg (10,000 lb) in geostationary orbit, and initial applications will be for the interplanetary Galileo and Ulysses Missions in 1986. The Shuttle/Centaur development program is discussed, the configurations and performance are described, and the unique integration and operations requirements related to the Shuttle are indicated. Design changes to the current Atlas/Centaur required for Shuttle operation are described here, and include those related to Orbiter cargo bay dimensions, environment, and safety considerations.

Stofan, A. J.↗

NASA NTRS1984

A high energy stage for the National Space Transportation System

The Shuttle/Centaur is an expendable hydrogen/oxygen cryogenic upper stage for use with the National Space Transportation System. It is a modification of the existing Atlas/Centaur which was used by NASA since 1966 to launch interplanetary and earth orbital payloads for numerous organizations. Two configurations of the Shuttle/Centaur are being developed. Vehicle capability includes placing approximately 4500 kg (10,000 lb) in geostationary orbit, and initial applications will be for the interplanetary Galileo and Ulysses Missions in 1986. The Shuttle/Centaur development program is discussed, the configurations and performance are described, and the unique integration and operations requirements related to the Shuttle are indicated. Design changes to the current Atlas/Centaur required for Shuttle operation are described here, and include those related to Orbiter cargo bay dimensions, environment, and safety considerations.

Stofan, A. J.↗

NASA NTRSDate not supplied

Recommendations For Developing Space Suit Integrated Food Systems and Delivering Nutrition Before, During, and After Lunar Eva

INTRODUCTION Artemis missions will include a higher tempo and frequency of extravehicular activities (EVAs) than any previous space program. Because of the physical demands expected from the crew, future space suit designs are required to incorporate nutritional support to the astronauts during lunar surface EVAs lasting longer than 4 hours. The purpose of this project was to provide recommendations to aid the development of an in-suit system that can adequately, safely, and acceptably deliver nutrition to a crewmember while confined to a space suit during EVA. METHODS Physiological, logistical, and engineering aspects of potential in-suit nutrition approaches were assessed through literature reviews, assessments of commercial off the shelf (COTS) foods, suit volumetric modeling, and feedback from subject matter experts and crewmembers. Key driving factors in the development of in-suit nutrition requirements included how much and what type of nutrition should be included, what food formulations are appropriate and safe, what are inherent limitations of space suits, what are the potential risks to the crewmember in the suit, and what practices and preferences from astronauts should be considered. Design references were conceptualized and assessed for strengths and limitations as potential in-suit nutrition systems for surface EVA. RESULTS Acute exogenous energy demands vary greatly depending on activity intensity and duration, and partial energy replenishment (i.e., 60–80 kcal∙hr-1 of EVA, or 460–680 kcal for EVAs lasting up to 8 hours) during activities could improve performance, safety, and recovery. COTS foods capable of providing these energy requirements exist; however, no COTS foods have been identified that pass NASA flight standards for microbiological safety and stability. In-suit nutrition delivery design references that were considered included in-suit concepts for a prefilled drink bag, a hydratable drink bag, and a solid food stick. In addition, a helmet feed port concept was considered for use with drink bags external to the suit. Volumetric models of the in-suit drink bag concepts, based on xEMU dimensions, indicate challenges of fitting formulations > 200 ml (equating to approximately 200 kcal). Astronaut feedback on the four concepts indicated that despite some individual preferences for inclusion of solid foods and helmet port designs, the prefilled drink bag concept was the most preferred. A prefilled drink bag can only be used if food safety and stability can be ensured, possibly requiring advancements in food delivery hardware. CONCLUSION The ability to meet the increased need for nutrition during surface EVAs through provision of nutrients in the suited configuration would benefit overall crew health, performance, and morale, and thus increase the likelihood of mission success. It is recommended that in-suit nutrition capabilities provide at least 400–600 kcal within the suit during EVAs lasting > 4 hours and that suit designs include a dedicated volume for food grade nutrition systems. The developed food system should either allow for 1) installation of prefilled (sealed sterile) liquid nutrition in the suit and provide a mechanism to break the seal at the time that consumption is desired or 2) demonstrate that the unsealed food product shelf life allows for safe consumption after at least 12 hours of EVA.

E L Dillon↗

NASA NTRSDate not supplied

Recommendations for Developing Space Suit Integrated Food Systems and Delivering Nutrition Before, During, and After Lunar EVA

INTRODUCTION Artemis missions will include a higher tempo and frequency of extravehicular activities (EVAs) than any previous space program. Because of the physical demands expected from the crew, future space suit designs are required to incorporate nutritional support to the astronauts during lunar surface EVAs lasting longer than 4 hours. The purpose of this project was to provide recommendations to aid the development of an in-suit system that can adequately, safely, and acceptably deliver nutrition to a crewmember while confined to a space suit during EVA. METHODS Physiological, logistical, and engineering aspects of potential in-suit nutrition approaches were assessed through literature reviews, assessments of commercial off the shelf (COTS) foods, suit volumetric modeling, and feedback from subject matter experts and crewmembers. Key driving factors in the development of in-suit nutrition requirements included how much and what type of nutrition should be included, what food formulations are appropriate and safe, what are inherent limitations of space suits, what are the potential risks to the crewmember in the suit, and what practices and preferences from astronauts should be considered. Design references were conceptualized and assessed for strengths and limitations as potential in-suit nutrition systems for surface EVA. RESULTS Acute exogenous energy demands vary greatly depending on activity intensity and duration, and partial energy replenishment (i.e., 60–80 kcal∙hr-1 of EVA, or 460–680 kcal for EVAs lasting up to 8 hours) during activities could improve performance, safety, and recovery. COTS foods capable of providing these energy requirements exist; however, no COTS foods have been identified that pass NASA flight standards for microbiological safety and stability. In-suit nutrition delivery design references that were considered included in-suit concepts for a prefilled drink bag, a hydratable drink bag, and a solid food stick. In addition, a helmet feed port concept was considered for use with drink bags external to the suit. Volumetric models of the in-suit drink bag concepts, based on xEMU dimensions, indicate challenges of fitting formulations > 200 ml (equating to approximately 200 kcal). Astronaut feedback on the four concepts indicated that despite some individual preferences for inclusion of solid foods and helmet port designs, the prefilled drink bag concept was the most preferred. A prefilled drink bag can only be used if food safety and stability can be ensured, possibly requiring advancements in food delivery hardware. CONCLUSION The ability to meet the increased need for nutrition during surface EVAs through provision of nutrients in the suited configuration would benefit overall crew health, performance, and morale, and thus increase the likelihood of mission success. It is recommended that in-suit nutrition capabilities provide at least 400–600 kcal within the suit during EVAs lasting > 4 hours and that suit designs include a dedicated volume for food grade nutrition systems. The developed food system should either allow for 1) installation of prefilled (sealed sterile) liquid nutrition in the suit and provide a mechanism to break the seal at the time that consumption is desired or 2) demonstrate that the unsealed food product shelf life allows for safe consumption after at least 12 hours of EVA.

space suit↗