Search NASA⌕ Search

SEARCH · Search NASA

Results for “Shear Zone”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Microstructural, Corrosion, and Mechanical Characterization of Friction Stir Welded Al 6022-to-ZEK100 Mg Joints

Friction stir welded (FSW) aluminum–magnesium lightweight vehicle joints have gained significant interest due to their high strength-to-weight ratio. In this work, the corrosion resistance of this material is analyzed through electrochemical tests, which include open circuit potential (OCP) inspection and potentiodynamic polarization (PD) scanning. Weight loss measurements tested the corrosion rate of the FSW weld through cyclic corrosion testing (CCT) according to the standard SAEJ 2334. Mechanical properties were also investigated, including lap-shear strength, micro- and nano-hardness mapping, and true stress–strain curves as a function of local processing history. The electrochemical results indicate that the center weld zone’s corrosion property stays between the two base alloys. Indentation-based testing demonstrated that the weld zone behaves differently from base alloys. Lap shear strength surprisingly did not drop much even after eight weeks of cyclic corrosion tests, indicating that the joint did not allow any ingress of the electrolyte.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Pervasive low-velocity layer atop the 410-km discontinuity beneath the northwest Pacific subduction zone: Implications for rheology and geodynamics

Regional triplication waveforms of five intermediate-depth events are modeled to simultaneously obtain the compressional (P) and shear (SH) wave velocity structure beneath northwestern Pacific subduction zone. Both the P- and SH-wave velocity models for three different sub-regions show a low-velocity layer (LVL) with a thickness of ~55-80 km lying above the 410-km discontinuity with a ~900 km lateral extent from the Japan Sea to the northeastern Asian continental margin. With the dihedral angle approaching to zero around 400 km, a minute amount of melt atop the 410-km discontinuity caused by the hydrous slab might completely wet olivine grain boundaries and result in a low seismic velocity layer in this specific subduction zone. This mechanism suggests that the 410-LVL is a low viscosity zone that would partially decouple the upper mantle from the transition zone. We infer that the widespread 410-LVL provides evidence for a water-bearing mantle transition zone beneath the western Pacific subduction zone.

58 GEOSCIENCES↗
DOE OSTI2021

Signature of transition to supershear rupture speed in the coseismic off-fault damage zone

Most earthquake ruptures propagate at speeds below the shear wave velocity within the crust, but in some rare cases, ruptures reach supershear speeds. The physics underlying the transition of natural subshear earthquakes to supershear ones is currently not fully understood. Most observational studies of supershear earthquakes have focused on determining which fault segments sustain fully grown supershear ruptures. Experimentally cross-validated numerical models have identified some of the key ingredients required to trigger a transition to supershear speed. However, the conditions for such a transition in nature are still unclear, including the precise location of this transition. In this work, we provide theoretical and numerical insights to identify the precise location of such a transition in nature. We use fracture mechanics arguments with multiple numerical models to identify the signature of supershear transition in coseismic off-fault damage. Furthermore, we then cross-validate this signature with high-resolution observations of fault zone width and early aftershock distributions. We confirm that the location of the transition from subshear to supershear speed is characterized by a decrease in the width of the coseismic off-fault damage zone. We thus help refine the precise location of such a transition for natural supershear earthquakes.

42 ENGINEERING↗
DOE OSTI2023

Microstructural, Corrosion and Mechanical Characterization of Friction-Stir Welded Joints Between Aluminum and Magnesium Alloys

Friction Stir Welding (FSW) of Aluminum-Magnesium (Al-Mg) alloys has garnered increasing attention due to its wide-ranging applications in the automotive and aerospace industries. The microstructural, corrosion, and mechanical properties of FSW Al-Mg welds under selected conditions are critical factors that must be well-investigated to ensure their durability and performance. In this study, electrochemical tests, including Open Circuit Potential (OCP), Linear Polarization Resistance (LPR), Potentiodynamic Polarization Scan (PD), and Electrochemical Impedance Spectroscopy (EIS), have been used to analyze the corrosion resistance of these welds, along with weight loss measurements through cyclic corrosion testing (CCT) and surface evolution via SEM over an 8-week period. Mechanical properties are evaluated through microindentation, nanoindentation, fatigue, and lap-shear tests. The results of the electrochemical tests reveal that the corrosion properties of the center weld zone differ from those of the two base alloys. Indentation tests indicate that the weld zone behaves differently from the base alloys. Surprisingly, the lap shear strength did not decrease significantly even after 8 weeks of cyclic corrosion testing, indicating that the joint prevented any ingress of the electrolyte. Fatigue testing showed that applying an adhesive between the Al and Mg joint improved the fatigue life to some extent, although the corrosion resistance reduced due to the discontinuous bonding of the adhesive layer. Overall, these findings highlight the importance of investigating the corrosion and mechanical properties of FSW Al-Mg welds and provide valuable insights for future modeling works.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2022

Elastic Anisotropy of Lizardite at Subduction Zone Conditions

Subduction zones transport water into Earth's deep interior through slab subduction. Serpentine minerals, the primary hydration product of ultramafic peridotite, are abundant in most subduction zones. Characterization of their high-temperature elasticity, particularly their anisotropy, will help us better estimate the extent of mantle serpentinization and the Earth's deep water cycle. Lizardite, the low-temperature polymorph of serpentine, is stable under the P-T conditions of cold subduction slabs (<260°C at 2 GPa), and its high-temperature elasticity remains unknown. Here we report ab initio elasticity and acoustic wave velocities of lizardite at P-T conditions of subduction zones. Our static results agree with previous studies. Its high-temperature velocities are much higher than previous experimental-based lizardite estimates with chrysotile but closer to antigorite velocities. The elastic anisotropy of lizardite is much larger than that of antigorite and could better account for the observed large shear-wave splitting in some cold slabs such as Tonga.

58 GEOSCIENCES↗
DOE OSTI2022

Simultaneous inference of plate boundary stresses and mantle rheology using adjoints: large-scale 2-D models

SUMMARY Plate motions are a primary surface constraint on plate and mantle dynamics and rheology, plate boundary stresses and the occurrence of great earthquakes. Within an optimization method, we use plate motion data to better constrain uncertain mantle parameters. For the optimization problem characterizing the maximum a posteriori rheological parameters we derive gradients using adjoints and expressions to approximate the posterior distributions for stresses within plate boundaries. We apply these methods to a 2-D cross section from the western to eastern Pacific, with temperature distributions and fault zone geometries developed primarily from seismic and plate motion data. We find that the best-fitting stress exponent, n, is about 2.8 and the yield stress about 100 MPa or less. The normal stress on the interplate fault zones is about 100 MPa and the shear stresses about 10 MPa or less.

Rudi, Johann (ORCID:0000000265639265)↗
DOE OSTI2020

Preseismic Fault Creep and Elastic Wave Amplitude Precursors Scale With Lab Earthquake Magnitude for the Continuum of Tectonic Failure Modes

Tectonic faults fail in a continuum of modes from slow earthquakes to elastodynamic rupture. Precursory variations in elastic wavespeed and amplitude, interpreted as indicators of imminent failure, have been observed in limited natural settings and lab experiments where they are thought to arise from contact rejuvenation and microcracking within and around the fault zone. However, the physical mechanisms and connections to fault creep are poorly understood. Here we vary loading stiffness during frictional shear to generate a range of slip modes and measure fault zone properties using transmitted elastic waves. We find that elastic wave amplitudes show clear changes before fault failure. The temporal onset of amplitude reduction scales with lab earthquake magnitude and the magnitude of this reduction varies with fault slip. Our data provide clear evidence of precursors to lab earthquakes and suggest that continuous seismic monitoring could be useful for assessing fault state and seismic hazard potential.

58 GEOSCIENCES↗
DOE OSTI2022

Sand Migration Simulation during Gas Production from Gas Hydrate Reservoir at Kuparuk 7–11–12 site in the Prodhoe Bay Unit, Alaska

Uncontrolled sand production impedes continuous gas production from a hydrate reservoir as observed in the past field-scale gas production tests. Sand mobilization is strongly linked with sediment deformation and high pressure gradient. Sand production occurs when the mobilized sands reach the well. Throughout gas production from a hydrate reservoir, because of hydrate dissociation, deformation and pressure gradient change both in time and space. Therefore, it is necessary to consider the entire process to identify where sand is likely mobilized and how much mobilized sand could reach the well. Here, this study utilizes a coupled thermal, hydrological, chemical, and mechanical (thermo-hydro-chemo-mechanical) sand migration model to simulate a year long gas production from the hydrate reservoir at the Kuparuk 7–11–12 site in the Prodhoe Bay Unit, Alaska. It is found that sand would mainly come from the lower portion of the production zone where faster hydrate dissociation occurs. The relatively faster hydrate dissociation coupled with the fact that hydrate-bearing sediments and hydrate-free sediments have similar stiffness but different strengths causes complex stress transfer, which results in excessive shear deformation when the upper portion of the production zone starts to dissociate. This is evident not only near the well but also away from the well, leading to a large amount of sand mobilization. Another focus of the modeling study is evaluation of the effect of sand migration on gas production. The comparison of two extreme cases–with sandscreen and without sandscreen–suggests that migrated and settled solids around a sand control device can prevent pressure drop across the near-wellbore zone and lead to reduction of the gas production rate.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Effect of Molecular Weight and Layer Thickness on Dielectric Breakdown Strength of Neat and Homopolymer Swollen Lamellar Block Copolymer Films

Designing next-generation lightweight pulsed power devices hinges on understanding the factors influencing the energy storage performance of dielectric materials. Polymer dielectric films have a quadratic dependence of energy storage on the voltage breakdown strength and strategies to enhance the breakdown strength are expected to yield a path toward high energy storage densities. Highly stratified lamellar block copolymer (L-BCP) films of model polystyrene-b-polymethylmethacrylate (PS-b-PMMA) exhibited as much as ~50% enhancement in breakdown voltage (E BD ), (225 % increase in stored energy density, U~ E BD 2 ), compared to unordered as-cast L-BCP films. Such an energy density using amorphous polymer is on par with industry-standard semi-crystalline biaxially oriented polypropylene (BOPP), and as such a notable development in the field. This work develops a deeper understanding of the molecular mechanisms of E BD enhancement in L-BCP films, due to combination of interface formation and spatial isolation of the chain ends into segregated zones. We further confirm the role of chain ends in the breakdown process blending a low M n L-BCP with matched M n homopolymers to attain same layer spacing as neat L-BCP of higher M n . E BD shows a significant decrease at low homopolymer fractions due to increased net chain end density within swollen ordered L-BCP domains in wet-brush regime, followed by increased E BD due to layer thickness increase via segregated “interphase layer” formation by excess homopolymers. Notably, E BD of homopolymer swollen L-BCPs is always lower than neat L-BCP of the same domain spacing, due to overall adverse chain ends contribution from homopolymers. These findings provide important selection rules for L-BCPs for designing next-generation flexible electronics with high energy density solid-state BCP film capacitors.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stress Controls Rupture Extent and Maximum Magnitude of Induced Earthquakes

Abstract Seismic hazard forecasts of induced seismicity often require estimates of the maximum possible magnitude ( M max ). Empirical models suggest that maximum magnitudes, or expected number of earthquakes, are related to the volume of injected fluid. We perform a suite of 3D physics‐based earthquake simulations with rate‐ and state‐dependent friction, systematically varying the area of the pressurized region and the amplitude of the initial homogeneous or heterogeneous shear stress. Using the resulting catalog we explore the conditions that result in pressure‐controlled versus runaway ruptures that extend outside the pressurized zone. We find that proposed empirical scaling laws correctly predict M max when shear stresses are further from failure (≤90% of maximum shear stress) and for high amplitude stress fields. Runaway ruptures are observed for higher initial shear stresses and smoother stress fields. In these cases, runaway ruptures occur early after the onset of injection and rarely preceded by foreshock activity.

58 GEOSCIENCES↗
DOE OSTI2023

The effect of shear strain and shear localization on fault healing

The seismic cycle of repeated earthquake failure requires that faults regain frictional strength during the interseismic phase, when the fault is locked or undergoing quasi-static creep. Fault healing plays a central role in determining earthquake stress drop, recurrence interval, elastic radiation frequency and other source parameters. In particular, the longer a fault remains quasi-stationary, the stronger it becomes and the larger the potential stress drop can be for the next event. Here, we address the role of shear strain and strain localization on fault healing and healing rate. We performed slide-hold-slide friction experiments on quartz gouge in the double-direct shear configuration for shear strain up to 25 and hold times from 10 to 1000 s. The results show that both healing and healing rate increase nonlinearly with increasing shear strain. Frictional healing scales with volumetric strain within the laboratory fault zone. Using the volumetric strain upon reshear as a proxy for strain localization, we demonstrate that the capacity of a fault to heal is directly proportional to shear bandwidth and degree of strain localization. The more the deformation is localized, the higher are the healing and healing rate, and thus, the fault strength. Our data provide a framework for understanding variations in fault strength over the seismic cycle and the role of brecciation and strain localization on spatiotemporal variations in fault strength.

58 GEOSCIENCES↗
DOE OSTI2024

Stochastic modal velocity field in rough-wall turbulence

Stochastically generated instantaneous velocity profiles are used to reproduce the outer region of rough-wall turbulent boundary layers in a range of Reynolds numbers extending from the wind tunnel to field conditions. Each profile consists in a sequence of steps, defined by the modal velocities and representing uniform momentum zones (UMZs), separated by velocity jumps representing the internal shear layers. Height-dependent UMZ is described by a minimal set of attributes: thickness, mid-height elevation, and streamwise (modal) and vertical velocities. These are informed by experimental observations and reproducing the statistical behaviour of rough-wall turbulence and attached eddy scaling, consistent with the corresponding experimental datasets. Sets of independently generated profiles are reorganized in the streamwise direction to form a spatially consistent modal velocity field, starting from any randomly selected profile. The operation allows one to stretch or compress the velocity field in space, increases the size of the domain and adjusts the size of the largest emerging structures to the Reynolds number of the simulated flow. By imposing the autocorrelation function of the modal velocity field to be anchored on the experimental measurements, we obtain a physically based spatial resolution, which is employed in the computation of the velocity spectrum, and second-order structure functions. The results reproduce the Kolmogorov inertial range extending from the UMZ and their attached-eddy vertical organization to the very-large-scale motions (VLSMs) introduced with the reordering process. The dynamic role of VLSM is confirmed in the –u'w' co-spectra and in their vertical derivative, representing a scale-dependent pressure gradient contribution.

42 ENGINEERING↗
DOE OSTI2020

Finite Element Modeling of the Fiber-Matrix Interface in Polymer Composites

Polymer composites are used in numerous industries due to their high specific strength and high specific stiffness. Composites have markedly different properties than both the reinforcement and the matrix. Of the several factors that govern the final properties of the composite, the interface is an important factor that influences the stress transfer between the fiber and matrix. The present study is an effort to characterize and model the fiber-matrix interface in polymer matrix composites. Finite element models were developed to study the interfacial behavior during pull-out of a single fiber in continuous fiber-reinforced polymer composites. A three-dimensional (3D) unit-cell cohesive damage model (CDM) for the fiber/matrix interface debonding was employed to investigate the effect of interface/sizing coverage on the fiber. Furthermore, a two-dimensional (2D) axisymmetric model was used to (a) analyze the sensitivity of interface stiffness, interface strength, friction coefficient, and fiber length via a parametric study; and (b) study the shear stress distribution across the fiber-interface-matrix zone. It was determined that the force required to debond a single fiber from the matrix is three times higher if there is adequate distribution of the sizing on the fiber. The parametric study indicated that cohesive strength was the most influential factor in debonding. Moreover, the stress distribution model showed the debonding mechanism of the interface. It was observed that the interface debonded first from the matrix and remained in contact with the fiber even when the fiber was completely pulled out.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Isotropic seismic radiation from rock damage and dilatancy

SUMMARY We present semi-analytical and numerical results on isotropic radiation expected to be generated by seismic sources with damaged dilatant materials that sustain during failure an overall shear deformation. The results are derived for inclusions with different stiffness components, including those responsible for shear-volumetric coupling in dilatant material, and different geometries, in a surrounding elastic solid. The obtained relations indicate that the isotropic seismic potency and seismic moment components are proportional to the shear potency components multiplied by the aspect ratio between the thickness and length of the source zone. For a typical rupture zone with a thin tabular geometry, the expected small aspect ratio explains the general seismological observations of small isotropic radiation. However, isotropic radiation induced by dynamic dilation for short and thick sources is more pronounced and may reach for spherical sources sustaining shear deformation 18 per cent of the shear components. Sources that include also tensile components and explosions can produce larger isotropic radiation. The results provide rigorous relations that can be used to estimate different source properties in numerical simulations, experiments and field studies.

Geochemistry & Geophysics↗
DOE OSTI2022

Unveiling the origins of work-hardening enhancement and mechanical instability in laser shock peened titanium

Laser shock-peening (LSP) produces complex gradients in microstructures and residual stresses, which enables fabrication of metallic engineering components with superior mechanical properties. In this work, we use non-destructive and spatially resolved high-energy X-ray diffraction (HE-XRD) to investigate the influences of LSP on microstructure, surface topography, and residual stress for high purity titanium plates. LSP is found to produce large compressive in-plane residual stresses near the peened surface which monotonically decay to zero about 2.5 mm below the surface. These properties were also tracked during in-situ tensile loading, allowing stress partitioning and work-hardening rates to be measured as a function of depth. The surface region is found to have the highest work-hardening rate and remain mechanically stable up to sample failure. In addition, a crystal rigid rotation along a transversal axis of about 27 & nbsp; was observed at large applied strain near the surface region, which is attributed to the formation of denser dispersed shear bands. Furthermore, a sudden drop in tensile stress was observed at a depth of similar to 160 mu m from the LSP surface, indicating the formation of a localized mechanical instability zone (LMIZ). The origin of this LMIZ could be attributed to the increase in shear stress induced by a load transfer from LSP surface due to the formation of denser dispersed shear bands. These observations indicate a localized transition in deformation behavior has occurred from dispersed shear banding to LMIZ and homogeneous deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Frequency–Magnitude Statistics of Laboratory Foreshocks Vary With Shear Velocity, Fault Slip Rate, and Shear Stress

Understanding the nucleation phase of earthquakes is key for advancing earthquake hazard assessment and improving earthquake early warning systems. However, little progress has been made in this area due to a poor understanding of nucleation processes and incomplete seismic and fault zone measurements. The ability to integrate measured fault zone properties with seismic data could significantly improve our understanding of how earthquakes begin and whether there are systematic variations in seismic properties preceding failure. In this work, we use high-resolution laboratory measurements of fault zone properties along with acoustic emission data to document temporal variations of foreshock properties. Our data show that foreshock size increases with shear stress, loading rate, and fault slip rate. We propose that the preseismic fault slip rate and fault zone thickness (i.e., porosity) work in concert to modulate foreshock properties.

15 GEOTHERMAL ENERGY↗
DOE OSTI2021

Shear Strength and Release of Large Cryogenic Pellets from the Barrel of a Shattered Pellet Injector for Disruption Mitigation

Shattered pellet injection (SPI) has been chosen as the baseline disruption mitigation system on ITER due to its ability to rapidly inject material deep into the plasma to greatly increase the plasma density and radiate the thermal energy. SPI utilizes a mechanical punch or high-pressure gas to release and accelerate a pellet that has been cryogenically desublimated in the barrel of a pipe gun. Various material injection combinations could possibly be implemented during different phases of a disruption event to radiate plasma energy, reduce electromagnetic loads on machine components, avoid the formation of runaway electrons, or to dissipate runaway electrons that form. Each injection phase could possibly utilize combinations of deuterium, neon, or argon. In this paper we outline experimental measurements of pellet material shear strength at SPI operating temperatures to understand the force needed to release SPI pellets. Deuterium, neon, argon, and deuterium-neon mixture pellets with diameters of 8.5, 12.5, and 15.7 mm are formed at a range of relevant gas pressures and temperatures and dislodged from the cold zone with a slow-moving piston driven by a motor. The slow-moving piston is kept above the triple point temperature of the material while the pellet is forming, then cooled to below the triple point temperature before contacting the pellet to minimize any thermal conduction to the pellet. The piston incorporates a load cell to measure the force applied when the pellet breaks away from the cold zone in the barrel.The ability of the gas and punch methods to exceed the shear strength of the studied pellet materials for release has been analyzed. High pressure gas delivered by fast opening valves produce pressure shock to the pellet due to supersonic expansion of the propellant gas. Pressure (and therefore, force) oscillations are present due to transverse density propagation throughout the breech volume. Mechanical punches deliver an impact force through a high-kinetic energy impact. The effect of the mechanical shock on the pellet has been explored and will be presented in this paper. Scaling to larger ITER size SPI pellets will be described.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Non-Rare Earth Magnesium Bumper Beams

Magna will team with the Pacific Northwest National Laboratory (PNNL) to develop Shear Assisted Processing and Extrusion (ShAPE™) of rectangular and multi-zoned extrusion profiles using non-RE Mg. It is envisioned that the ShAPE™ process, developed during this project for non-circular profiles, will serve as the foundation for fabrication of full-scale bumper beams of the future where near net-shapes are extruded directly from castings in a single step, without the need for costly rare earth additives. In this project, the ShAPE™ process will be developed for a rectangular profile measuring 1” x 2” with a 0.06” wall thickness. Successful extrusion of rectangular cross sections is a critical step along the path toward profiles with multiple zones. With the process established for a rectangular profile, the project will then make advancements toward multi-zoned cross sections. A magnesium alloy bumper beam offers a 35% weight savings compared to aluminum alloys and 60% compared to high strength steels. The bumper beam was chosen as the first component to target because the geometry can have a fairly simple 0.6-0.12 inch wall/web thickness, generally compatible with PNNL’s knowledge base and equipment capability surrounding ShAPE™. The bumper component offers commercial value by providing mass reduction in the front of the vehicle along with ride and handling benefit. PNNL has demonstrated the ability to ShAPE™ process non-RE Mg tubing with high strength, ductility and energy absorption. It has been shown that ShAPE™ extruded ZK60 and Mg2Si tubing with 0.30 inch diameter and 0.03 inch wall thickness have similar energy absorption to AA6061-T6. This is due to significant grain refinement, breakdown and dispersion of second phases, and the ability to eliminate anisotropy in compressive/tensile strength by aligning texture 45 degrees to the extrusion axis. Scalability of the ShAPE™ process has been demonstrated in ZK60 by fabricating 2.0 inch diameter tubing with 0.06 and 0.12 inch wall thicknesses having concentricity as tight as 1.3%. These tubes exhibit an ultimate tensile strength of 260-300 MPa and room temperature ductility of >20% parallel, perpendicular and 45 degrees to the extrusion axis. Aluminum bumpers represent approximately 54% of the NA light vehicle market. If the research effort is successful, providing a 30% mass reduction at equal cost relative to aluminum bumpers, it is anticipated that 25% market penetration would be realized over the next 5 year and 50% market share by 2030. 100% of the aluminum automotive bumpers are sourced from the tier network, providing resourcing opportunity based on equal performance, reduced mass and cost equivalent lower than aluminum bumpers. Due to the relatively low vehicle content, magnesium components are currently shredded and 100% recycled with aluminum content in the US, presenting a positive life cycle impact.

42 ENGINEERING↗