Search NASA⌕ Search

SEARCH · Search NASA

Results for “Size distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Development of Parameters for the Particle Size Distribution of TATB

Laser light scattering (LLS), manual counting of scanning electron microscopy (SEM) images, and reduction of SEM images using ImageJ (open source program) to determine Feret (caliper) diameters were applied to determine particle size distribution (PSD) of four preparations of 1,3,5‐triamino‐2,4,6‐trinitrobenzene (TATB) and yttria‐stabilized zirconia (YSZ), an SEM certified standard. Mie theory was used to reduce the LLS data. The spherical nature of the YSZ made it a good candidate for LLS. Variations in n , the refractive index, and iκ, the imaginary component, produced very little change in the PSD. However, changing the carrier liquid from H 2 O to a 40% aqueous sucrose solution, thereby changing the carrier refractive index, n 0 , substantially affected the PSD. The Mie complex refractive indices for the YSZ were n = 2.200, iκ = 0.100, with a 40% aqueous sucrose solution, n 0 = 1.400. The triclinic crystal structure of TATB made refractive index determinations more difficult, so a study was conducted varying Mie parameters and comparing them to the same data reduced using the Fraunhofer theory. Changing the n and κ parameters produced PSD with a small concentration of particles less than 1 µm in size or none in this range. SEM images, Feret data, manual counting, and Fraunhofer data reduction indicate particles less than 1 µm are probably < 5% in concentration. The final selection of Mie parameters for TATB was n = 2.283, iκ = 0.1, and suspension medium, n 0 = 1.330. Finally, computations, using density functional theory produced similar parameters.

Feret diameter↗
DOE OSTI2023

Nanoparticle Catalyst Formation and Subsequent Sintering: Size-Distribution Fundamental Understanding and Catalyst Control via Mechanism-Enabled Population Balance Modeling (Final Report)

The challenge of elucidating the chemical mechanisms by which nano- and other particles form, and then using those mechanisms to understand, analyze, and ideally predict particle-size and particle-size distributions, was undertaken. Thanks to multi-year, longer-term DOE support each of these challenges was successfully met. The community is now able to both predict, and control in cases where the underlying mechanism of particle formation has been determined, the key PS and PSD that are, in turn, critical properties that strongly influence the catalytic and other physical properties of nano- and larger particles across nature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Drop size distribution broadening mechanisms in a bin microphysics Eulerian model

In this study, processes that broaden drop size distributions (DSDs) in Eulerian models with two-moment bin microphysics are analyzed. Numerous tests are performed to isolate the effects of different physical mechanisms that broaden DSDs in two- and three-dimensional Weather Research and Forecasting model simulations of an idealized ice-free cumulus cloud. Additionally, sensitivity of these effects to modifying horizontal and vertical model grid spacings is also examined. As expected, collision-coalescence is a key process broadening the modeled DSDs. In-cloud droplet activation also contributes substantially to DSD broadening, whereas evaporation has only a minor effect and sedimentation has little effect. Cloud dilution (mixing of cloud-free and cloudy air) also broadens the DSDs considerably, whether or not it is accompanied by evaporation. This mechanism involves the reduction of droplet concentration from dilution along the cloud’s lateral edges, leading to locally high supersaturation and enhanced drop growth when this air is subsequently lifted in the updraft. DSD broadening ensues when the DSDs are mixed with those from the cloud core. Decreasing the horizontal and vertical model grid spacings from 100 m to 30 m has limited impact on the DSDs. However, when these physical broadening mechanisms (in-cloud activation, collision-coalescence, dilution, etc.) are turned off, there is a reduction of DSD width by up to ~20-50% when the vertical grid spacing is decreased from 100 m to 30 m, consistent with effects of artificial broadening from vertical numerical diffusion. Nonetheless, this artificial numerical broadening appears to be relatively unimportant overall for DSD broadening when physically based broadening mechanisms in the model are included for this cumulus case.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Effects of Particle Size Distribution with Efficient Packing on Powder Flowability and Selective Laser Melting Process

The powder bed-based additive manufacturing (AM) process contains uncertainties in the powder spreading process and powder bed quality, leading to problems in repeatability and quality of the additively manufactured parts. This work focuses on identifying the uncertainty induced by particle size distribution (PSD) on powder flowability and the laser melting process, using Ti6Al4V as a model material. The flowability test results show that the effect of PSDs on flowability is not linear, rather the PSDs near dense packing ratios cause significant reductions in flowability (indicated by the increase in the avalanche angle and break energy of the powders measured by a revolution powder analyzer). The effects of PSDs on the selective laser melting (SLM) process are identified by using in-situ high-speed X-ray imaging to observe the melt pool dynamics during the melting process. The results show that the powder beds made of powders with dense packing ratios exhibit larger build height during laser melting. The effects of PSD with efficient packing on powder flowability and selective laser melting process revealed in this work are important for understanding process uncertainties induced by feedstock powders and for designing mitigation approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Revisiting the Hail Radar Reflectivity–Kinetic Energy Flux Relation by Combining T-Matrix and Discrete Dipole Approximation Calculations to Size Distribution Observations

The retrieval of hail kinetic energy with weather radars or its simulation in numerical models is challenging because of the shape complexity and variable density of hailstones. We combine 3D scans of individual hailstones with measurements of the particle size distributions (PSD) and T-matrix calculations to understand how hail reflectivity Z changes when approximating hailstones as spheroids, as compared to the realistic shapes obtained by 3D scanning technology. Additionally, recent terminal velocity relations are used to compare Z to the hail kinetic energy flux E ˙ . We parameterize the hail backscattering cross sections at L, S, C, and X bands as a function of size between 0.5 and 5.0 cm, matching the range of the observed PSDs. The scattering calculations use the T-matrix method for size parameters below 1.0 and the discrete dipole approximation (DDA) method otherwise. The DDA calculations are done for 48 digital models of realistic hailstones of sizes between 1 and 5 cm. The DDA cross sections are calculated for multiple orientations and averaged assuming a fully random orientation distribution to provide a single value per hailstone. The T-matrix reflectivity assuming solid ice spheres presents negligible differences to DDA results for size parameters below 1.0. Therefore, T matrix was used to fill in the gaps left by the DDA calculations. The results are mapped to the same size bins of the observed PSDs, allowing the calculation of the radar reflectivity. This is then correlated to E ˙ , allowing a potential improvement of past retrieval methods of E ˙ from Z in multiple wavelengths.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Drop Size Distribution Variability in Central Argentina during RELAMPAGO-CACTI

The Remote sensing of Electrification, Lightning, And Meso-scale/micro-scale Processes with Adaptive Ground Observations (RELAMPAGO) and the Cloud, Aerosol, and Complex Terrain Interactions Experiment Proposal (CACTI) field campaigns provided an unprecedented thirteen-disdrometer dataset in Central Argentina during the Intensive (IOP, 15 November to 15 December 2018) and Extended (EOP, 15 October 2018 to 30 April 2019) Observational Periods. The drop size distribution (DSD) parameters and their variability were analyzed across the region of interest, which was divided into three subregions characterized by the differing proximity to the Sierras de Córdoba (SDC), in order to assess the impact of complex terrain on the DSD parameters. A rigorous quality control of the data was first performed. The frequency distributions of DSD-derived parameters were analyzed, including the normalized intercept parameter (logN w ), the mean volume diameter (D 0 ), the mean mass diameter (D m ), the shape parameter (μ), the liquid water content (LWC), and the rain rate (R). The region closest to the SDC presented higher values of logN w , lower D 0 , and higher μ, while the opposite occurred in the farthest region, i.e., the concentration of small drops decreased while the concentration of bigger drops increased with the distance to the east of the SDC. Furthermore, the region closest to the SDC showed a bimodal distribution of D 0 : the lower values of D 0 were associated with higher values of logN w and were found more frequently during the afternoon, while the higher D 0 were associated with lower logN w and occurred more frequently during the night. The data were analyzed in comparison to the statistical analysis of Dolan et al. 2018 and sorted according to the classification proposed in the cited study. The logN w -D 0 and LWC-D 0 two-dimensional distributions allowed further discussion around the applicability of other mid-latitude and global precipitation classification schemes (startiform/convection) in the region of interest. Finally, three precipitation case studies were analyzed with supporting polarimetric radar data in order to relate the DSD characteristics to the precipitation type and the microphysical processes involved in each case.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

From Hydrometeor Size Distribution Measurements to Projections of Wind Turbine Blade Leading-Edge Erosion

Wind turbine blade leading-edge erosion (LEE) is a cause of increased operation and maintenance costs and decreased annual energy production. Thus, detailed, site-specific quantification of likely erosion conditions are critically needed to inform wind plant owner/operator decisions regarding mitigation strategies. Estimating the damage potential at a wind plant site requires accurate measurement of precipitation intensity, phase, droplet size distributions, wind speeds and their joint statistics. The current work quantifies the effect of disdrometer type on the characterization of LEE potential at a site in the US Southern Great Plains. using observations from three co-located disdrometers (an optical, an impact and a video disdrometer), along with hub-height wind-speed observations from a Doppler lidar and two LEE models: a kinetic energy model and the Springer model. Estimates of total kinetic energy of hydrometeor impacts over the four-year study period vary by as much as 38%, and coating lifetime derived from accumulated distance-to-failure estimates from the Springer model differ by an even greater amount, depending on disdrometer type. Damage potential at this site is concentrated in time, with 50% of impact kinetic energy occurring in 6–12 h per year, depending on which set of disdrometer observations is used. Rotor-speed curtailment during the most erosive 0.1–0.2% of 10 min periods is found to increase blade lifetimes and lead to the lowest levelized cost of energy.

17 WIND ENERGY↗
DOE OSTI2022

Evolution of Droplet Size Distributions During the Transition of an Ultraclean Stratocumulus Cloud System to Open Cell Structure: An LES Investigation Using Lagrangian Microphysics

Here, a state-of-the-art Lagrangian microphysics scheme is used in a large-eddy simulation to investigate the stratocumulus transition from closed to open cell structure. Processes controlling precipitation development, which is a key to the transition, are analyzed by leveraging unique benefits of Lagrangian microphysics, particularly the ability to track computational drops in the flow. Sufficient time is needed for coalescence growth of cloud drops to drizzle within the updraft-downdraft cycle of large eddies. This favors broad drop size distributions (DSDs) and drizzle growth in downdrafts, where drops are typically much older than in updrafts. During the closed cell stage, mean cloud drop radius is too small, and the DSDs are too narrow, so that the timescale for coalescence is much longer than the large eddy turnover time and drizzle growth is limited. The closed-to-open cell transition occurs when these timescales become comparable and the precipitation flux increases sharply.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Statistical Characteristics of Raindrop Size Distributions and Parameters in Central China during the Meiyu Seasons

The rain parameters measured by the laser OTT Parsivel raindrop disdrometer (Parsivel), the two-dimensional video disdrometer (2DVD) and DZZ5 tipping-bucket rain gauge (RG) during the Integrative Monsoon Frontal Rainfall Experiment (IMFRE) in summer 2018 are compared. The total rain amounts observed by Parsivel, 2DVD, and RG during IMFRE are 178.07 mm, 176.76 mm and 182.5 mm, while their total rainy hours are 113, 113 and 90. The mean Dm (mass-weighted mean diameter) and liquid water content values derived from Parsivel and 2DVD are 0.9 mm and 1.02 mm, and 0.247 g m-3 and 0.223 g m-3, respectively, and Parsivel is more sensitive to small raindrops (< 1 mm) than 2DVD. The raindrop spectra measured by Parsivel and 2DVD have excellent agreement for both convective rain (CR) and stratiform rain (SR) within a range of Dm from 1 to 3.5 mm. The rain samples from six Parsivel sites over the middle reaches of the Yangtze River during the 2016–2018 meiyu seasons have been collected and processed. The frequency occurrences for rain rates (RR) < 5 and > 10 mm h-1 are 83.9% and 7.4%, respectively, but they contribute 30.5% and 52.1 % of the total accumulated rainfall. Comparing the results with those over the lower reaches, the RR and total accumulated rainfall over the middle reaches are greater, especially for heavy rainfall. The rain drop size distributions (DSDs) in this study are wider and have higher number concentration than those from the lower reaches.

Raindrop size distribution, Meiyu front, disdromet↗
DOE OSTI2023

Assessing the influence of microstructure on uranium hydride size distributions via small angle neutron scattering

Here, the effect of microstructure on the internal hydriding behavior of both cast (1 mm grain size) and rolled (25 μm grain size) uranium containing hydrogen concentrations between 0 and 1.8 wppm were evaluated via small angle neutron scattering (SANS). Increasing hydrogen content up to 1.8 wppm in the cast uranium only weakly affected the average uranium hydride (UH 3 ) precipitate size, calculated from the SANS data. Conversely, the UH 3 phase fraction was found to strongly depend on the hydrogen content in the same cast samples. A substantially reduced UH 3 particle size distribution was observed in the rolled uranium relative to cast uranium containing the same nominal hydrogen content. It is hypothesized that the suppression of UH 3 formation in the rolled uranium is driven by increased hydrogen trapping at grain boundaries, and theoretical calculations that account for trap density, potency, and hydrogen diffusion kinetics support this hypothesis.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Confronting Large‐Eddy Simulations With Stereo Camera Data by Means of Reconstructed Hemispheric Cloud Size Distributions

High-resolution hemispheric camera images at a meteorological site in western Germany are used to analyze the multi-dimensional spatial characteristics of continental cumulus cloud fields, and to evaluate Large-Eddy Simulations on this aspect. Traditional non-hemispheric cloud-detecting instruments provide additional reference data. The main model-observation comparison focuses on cloud size distributions (CSDs), employing two methods: (a) directly using three-dimensional model fields, direct CSDs, and (b) using rendered hemispheric images of the model fields as produced by a camera simulator based on path-tracing. In the latter method, both the real and rendered images are used to three-dimensionally reconstruct the cloud fields, yielding hemispheric CSDs. Advantages of hemispheric comparisons over more classic approaches include (a) fair comparisons between model and data, and (b) full use of the enhanced resolutions and hemispheric spatial coverage of the camera imagery. Basic evaluation of the simulations demonstrates good agreement on thermodynamic structure and its diurnal cycle. Cloud heights and cloud cover are intercompared between the model, camera data and other instrumentation, providing insight into their structural differences. A consistent alignment is found between the hemispheric CSDs from both the model and the cameras. Power law fits reveal structurally lower exponents in hemispheric CSDs compared to non-hemispheric CSDs, which particularly caution against directly comparing hemispheric CSDs to non-hemispheric distributions. This result is robust for sample size and fitting method. These findings inform future use of hemispheric camera systems for studying cumulus cloud field morphology and model evaluation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Phase Doppler Interferometry for Efficient Cloud Drop Size Distribution, Number Density, and LWC Measurements

Threats to aviation safety as a result of super-cooled large drops (SLD) has been addressed by the FAA rules change (14 CFR Part 25) with the additional icing certification requirement. SLD clouds often consist of bi-modal drop size spectra leading to significant problems in simulating and characterizing these conditions in situ and in icing wind tunnels. Legacy instrumentation for measuring drop size distributions and liquid water content are challenged under these conditions. The large size range measurement problem is addressed with the development of the Phase Doppler Interferometer, Flight Probe Dual-Range (PDI FPDR). The method is described in this report along with the measurement capabilities including the dynamic measurement range and overall working size range. The PDI instrument bases drop size measurements on the light wavelength as the measurement length scale. The light wavelength is a much more robust scale, especially as compared to the light scattering intensity. Additionally, methods for accurately characterizing the sample volume in situ based on measured drop velocity and transit time are reviewed, given the importance of this parameter for merging results and measuring LWC. Droplet coincidence in the sample volume can be problematic so this condition is treated with an innovative signal parsing approach. Measurement examples acquired in the NASA IRT are provided. Measurements of LWC showed good agreement with the Artium Particle Imaging (PI) instrument but diverged from the tunnel calibration results for larger MVD values.

42 ENGINEERING↗
DOE OSTI2023

Size distribution of polycyclic aromatic hydrocarbons in space: an old new light on the 11.2/3.3 μm intensity ratio

The intensity ratio of the 11.2/3.3 μm emission bands is considered to be a reliable tracer of the size distribution of polycyclic aromatic hydrocarbons (PAHs) in the interstellar medium (ISM). This paper describes the validation of the calculated intrinsic infrared (IR) spectra of PAHs that underlie the interpretation of the observed ratio. The comparison of harmonic calculations from the NASA Ames PAH IR spectroscopic database to gas-phase experimental absorption IR spectra reveals a consistent underestimation of the 11.2/3.3 μm intensity ratio by 34%. IR spectra based on higher level anharmonic calculations, on the other hand, are in very good agreement with the experiments. While there are indications that the 11.2/3.3 μm ratio increases systematically for PAHs in the relevant size range when using a larger basis set, it is unfortunately not yet possible to reliably calculate anharmonic spectra for large PAHs. Based on these considerations, we have adjusted the intrinsic ratio of these modes and incorporated this in an interstellar PAH emission model. This corrected model implies that typical PAH sizes in reflection nebulae such as NGC 7023 – previously inferred to be in the range of 50 to 70 carbon atoms per PAH are actually in the range of 40 to 55 carbon atoms. The higher limit of this range is close to the size of the C 60 fullerene (also detected in reflection nebulae), which would be in line with the hypothesis that, under appropriate conditions, large PAHs are converted into the more stable fullerenes in the ISM.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Consideration of Initial Cloud Droplet Size Distribution Shapes in Quantifying Different Entrainment-Mixing Mechanisms

Entrainment-mixing process significantly affects cloud micro/macrophysics and the evaluation of aerosol indirect effects. However, it remains an open question as to how to quantify entrainment-mixing mechanism for broad cloud droplet size distributions (CDSDs). Here, CDSDs with different spectral widths are used to initialize the Explicit Mixing Parcel Model to address this problem, and microphysical properties are compared for different CDSD widths. For relatively broad CDSDs, as the number concentration and liquid water content decrease, the volume-mean radius and mean radius increase, which is opposite to the scenario for relatively narrow CDSDs and the homogeneous/inhomogeneous conceptual model. For the relatively broad CDSDs, such relationships could be mistaken as inhomogeneous mixing with subsequent ascent in analysis of the conventional microphysical mixing diagram. This then causes traditional homogenous mixing degrees to be unrealistically negative and not applicable for relatively broad CDSDs. New measures are introduced to explicitly account for the effect of CDSD spectral shapes on quantifying entrainment-mixing mechanism. The new measures yield reasonable ranges of values that conform to the dynamical measures such as the Damköhler and transitional scale numbers, and their temporal variation can be explained physically. This study extends the measures of homogeneous mixing degrees from narrow to broad CDSDs, and sheds new light on the consideration of CDSD shapes in parameterizations of entrainment-mixing mechanism.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Updimensioning strategy derived from synthetic equiaxed grain structures for approximating 3D grain size distributions from 2D visualizations with 1D parameters

We generated synthetic equiaxed grain structures using computer graphics software to explore the relationship between various grain size determination methods and true three-dimensional (3D) grain diameters. Mirroring grain measurement techniques, the synthetic 3D grain structures are imaged as 2D micrographs which are measured to yield 1D grain size parameters. Synthetic grain structures provide data at a mass scale and permit exploration of both polished and fractured surface micrographs, revealing one-to-one correspondence between exposed 2D grain cross-sections and individual 3D grains. Analysis of this correspondence yielded a procedure to approximate 3D equiaxed grain size and volume distributions based on the mode of the 2D fractograph grain size distribution. The 3D approximation procedure is shown to be less susceptible to different imaging conditions that affect small, undiscernible grains compared to the standard planimetric and linear intercept methods, which by design also tend to underestimate the 3D grain diameter. The procedure requires larger sample sizes to lower variance and a deeper analysis which could become more practical with machine learning (ML) models for grain boundary segmentation, which synthetic grain structures can help train. This work lays the foundation for analyzing other grain distributions such as columnar and composite grains in similar depth.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Nuclear Waste Tank Emission Contributions to Particle Size Distribution

Pollutants from anthropogenic activities including industrial processes are ubiquitous to the environment. To understand the impact from industrial aerosol on climate and human health, industrial aerosol needs to be better characterized. Here, in this study, particle number concentrations were used as a proxy for atmospheric pollutants, which include both particles and gases. Particle concentration and size distribution were measured using a scanning mobility particle sizer (SMPS) approximately 4.5 km from primary industrial areas at the Savannah River Site in Aiken, SC. Industrial areas include numerous nuclear waste storage and processing tanks. The SMPS data were divided into two groups depending on the wind direction measured onsite to categorize transport from the industrial area or from elsewhere. Industrial contributions were found to have a higher concentration of particles with sizes less than 200 nm, 859 ± 564 cm -3 , in comparison to non-industrial attributed particles, 733 ± 495 cm -3 on average from March-July 2021. For sizes larger than 200 nm, industrial and non-industrial particles have a similar concentration, 89 ± 59 cm -3 and 99 ± 61 cm -3 , with non-industrial concentrations being slightly larger. To confirm that industrial particles could travel to the sampling location, air dispersion modeling was completed for specific case studies during the sampling period. The atmospheric dispersion modeling results confirmed that particles released at the industrial areas reached the sampling location when the wind direction was favorable for transport from the industrial areas. The greater concentration of smaller-sized particles in industrial emissions has implications for typical particulate measurements (PM2.5), heath impacts, and climatological influences.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Factors controlling marine aerosol size distributions and their climate effects over the northwest Atlantic Ocean region

Abstract. Aerosols over Earth's remote and spatially extensive ocean surfaces have important influences on planetary climate. However, these aerosols and their effects remain poorly understood, in part due to the remoteness and limited observations over these regions. In this study, we seek to understand factors that shape marine aerosol size distributions and composition in the northwest Atlantic Ocean region. We use the GEOS-Chem model with the TwO-Moment Aerosol Sectional (TOMAS) microphysics algorithm model to interpret measurements collected from ship and aircraft during the four seasonal campaigns of the North Atlantic Aerosols and Marine Ecosystems Study (NAAMES) conducted between 2015 and 2018. Observations from the NAAMES campaigns show enhancements in the campaign-median number of aerosols with diameters larger than 3 nm in the lower troposphere (below 6 km), most pronounced during the phytoplankton bloom maxima (May/June) below 2 km in the free troposphere. Our simulations, combined with NAAMES ship and aircraft measurements, suggest several key factors that contribute to aerosol number and size in the northwest Atlantic lower troposphere, with significant regional-mean (40–60∘ N and 20–50∘ W) cloud-albedo aerosol indirect effect (AIE) and direct radiative effect (DRE) processes during the phytoplankton bloom. These key factors and their associated simulated radiative effects in the region include the following: (1) particle formation near and above the marine boundary layer (MBL) top (AIE: −3.37 W m−2, DRE: −0.62 W m−2); (2) particle growth due to marine secondary organic aerosol (MSOA) as the nascent particles subside into the MBL, enabling them to become cloud-condensation-nuclei-sized particles (AIE: −2.27 W m−2, DRE: −0.10 W m−2); (3) particle formation and growth due to the products of dimethyl sulfide, above and within the MBL (−1.29 W m−2, DRE: −0.06 W m−2); (4) ship emissions (AIE: −0.62 W m−2, DRE: −0.05 W m−2); and (5) primary sea spray emissions (AIE: +0.04 W m−2, DRE: −0.79 W m−2). Our results suggest that a synergy of particle formation in the lower troposphere (particularly near and above the MBL top) and growth by MSOA contributes strongly to cloud-condensation-nuclei-sized particles with significant regional radiative effects in the northwest Atlantic. To gain confidence in radiative effect magnitudes, future work is needed to understand (1) the sources and temperature dependence of condensable marine vapors forming MSOA, (2) primary sea spray emissions, and (3) the species that can form new particles in the lower troposphere and grow these particles as they descend into the marine boundary layer.

54 ENVIRONMENTAL SCIENCES↗