Search NASA⌕ Search

SEARCH · Search NASA

Results for “Slip”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Coupled geomechanical investigation of depletion-induced fault reactivation

Fault reactivation during subsurface fluid production pose significant challenges to safe and sustainable resource extraction. Here, this study presents a three-dimensional coupled geomechanical framework to investigate the processes driving fault reactivation, capturing the interactions between reservoir dynamics and geomechanical responses. Verification against theoretical estimations based on linear poroelasticity confirms the model's capacity in representing reservoir background stress responses. However, the study reveals that relying solely on background stress states can underestimate or overestimate fault reactivation potential, emphasizing the importance of including localized stress perturbations such as differential compaction and stress redistribution. Applied to a fault (M1) inspired by the geological characteristics of the Groningen field, the model shows slip initiation at 2965 m depth with 16.0 MPa depletion, aligning with field observations where seismicity occurred at approximately 3 km depth after 15.8 MPa depletion. Parametric studies reveal: (1) inelastic reservoir compaction delays fault reactivation and mitigates fault slip by reducing stress concentration, (2) higher intermediate in-situ stress magnitudes decrease the Coulomb Failure Stress (CFS) increase rate and reduce fault slip, (3) larger fault offsets amplify shear stress near the offset zone, promoting earlier reactivation and longer rupture propagation, and (4) fault permeability significantly influences pressure diffusion, with low-permeability faults leading to sharper stress changes and earlier fault destabilization. These insights highlight the critical role of geological and mechanical parameters in fault reactivation and provide a predictive framework for mitigating induced seismicity risks.

Coupled geomechanical modeling↗
DOE OSTI2025

Hydrogen influences thermal activation parameters for dislocation glide during low cycle fatigue of 316L stainless steel

Measurements of activation areas are used to investigate the effect of hydrogen on the kinetics of dislocation glide during cyclic deformation in cold-worked 316L stainless steel. Non-charged and hydrogen-precharged (H-precharged) specimens were tested in low cycle fatigue (LCF) under plastic strain control. A series of plastic strain rate changes was performed periodically at the peak true plastic strain from the first cycle to half-life, and at various plastic strain values around stable hysteresis loops near half-life to determine the operational activation area, Δ a ∗. Both material conditions demonstrate a rapid increase in Δ a ∗ during the initial rapid softening followed by a region of approximately constant values coinciding with a reduced rate of softening. Near half-life, hydrogen reduces Δ a ∗ at a given true stress due to its effect on the activation distance and obstacle spacing. The magnitudes of Δ a ∗ reveal that bypassing solutes, cutting forest dislocations, and initiating cross slip are important mechanisms of thermally activated dislocation glide at all amplitudes, except hydrogen suppresses cross slip at the lowest plastic strain amplitudes. These results are supported by electron microscopy characterization of deformed microstructures. A Haasen plot analysis indicates that forest dislocations control the kinetics of deformation in both material conditions. It also reveals the presence of athermal obstacles in both non-charged and H-precharged conditions, likely dense dislocation tangles and cell walls. Additionally, the effect of hydrogen on microstructure evolution (by reducing the propensity for cross slip) leads to a dependence of athermal stress on plastic strain amplitude.

Activation area↗
DOE OSTI2025

Understanding the deformation behavior of the γ rich transformative Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy using in situ synchrotron diffraction

In situ tensile testing coupled with synchrotron x-ray diffraction was used to study the deformation behavior of metastability-engineered Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 complex concentrated alloy. Monitoring the evolution of phase fraction and strain hardening response allowed the determination of true critical stress for the onset of the transformation-induced plasticity (TRIP) to be ∼375 MPa, preceded by slip starting at ∼255 MPa. In situ EBSD was used to validate the critical stress for transformation at the microstructure level and observe slip traces to confirm prior slip activity before the transformation. Further, a modeling framework based on stacking fault energy (SFE) was developed to predict the critical stress for transformation. Modeling suggested the SFE of the alloy to fall nearly 15 mJ/m 2 , which agrees well with SFE values calculated using synchrotron peak shifting (12 mJ/m 2 ) and thermodynamic calculation (11 mJ/m 2 ). As a result of γ-fcc to ε-hcp phase transformation, new {0002} ε planes emerged parallel to unaligned {111} γ planes with the tensile loading following S-N orientation relationship. Such selective emergence of new diffraction rings corresponding to ε phase is understood based on the reorientation of γ crystals with reference to tensile axis. In conclusion, this approach can be extended to effectively design alloys based on critical stress required for activating different deformation mechanisms to further push the limits of the strength-ductility envelope.

Complex concentrated alloy↗
DOE OSTI2025

Deformation of Hydrous Phases Egg [AlSiO 3 (OH)], δ [AlO(OH)] and Stishovite [Si 1‐n H 4n O 2 ] Relevant to Anisotropy of the Earth's Mantle

Seismic anisotropy of the Earth's mantle has been mostly attributed to crystallographic preferred orientation (CPO) generated during subduction and convection of an anhydrous mantle. But some hydrous phases are also stable at mantle conditions. Here we present results from diamond-anvil cell deformation experiments at high pressure and temperature on hydrous phases Egg [AlSiO 3 (OH)], δ [AlO(OH)] and hydrous stishovite [Si 1-n H 4n O 2 ], transformed from the clay mineral kaolinite. They develop strong CPO during axial compression, suggesting that they likely contribute to seismic anisotropy and heterogeneity in the mantle. Comparing experimental results with viscoplastic polycrystal plasticity models suggest that phase Egg deforms dominantly by (001) slip, δ by (010) slip and stishovite by {100} slip which could be incorporated in future models of mantle geodynamics.

58 GEOSCIENCES↗
DOE OSTI2024

Uncovering the phonon spectra and lattice dynamics of plastically deformable InSe van der Waals crystals

Stacking two-dimensional (2D) van der Waals (vdW) materials in a layered bulk structure provides an appealing platform for the emergence of exotic physical properties. As a vdW crystal with exceptional plasticity, InSe offers the opportunity to explore various effects arising from the coupling of its peculiar mechanical behaviors and other physical properties. Here, we employ neutron scattering techniques to investigate the correlations of plastic interlayer slip, lattice anharmonicity, and thermal transport in InSe crystals. Not only are the interlayer slip direction and magnitude well captured by shifts in the Bragg reflections, but we also observe a deviation from the expected Debye behaviour in the heat capacity and lattice thermal conductivity. Combining the experimental data with first-principles calculations, we tentatively attribute the observed evidence of strong phonon-phonon interactions to a combination of a large acoustic-optical frequency resonance and a nesting effect. These findings correlate the macroscopic plastic slip and the microscopic lattice dynamics, providing insights into the mechano-thermo coupling and modulation in 2D vdW materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Shape effects on the local dynamics of suspensions of spheroidal particles

The effect of shape on the dynamics of suspensions of non-spherical heavy particles is examined by fully resolved numerical simulations of oblate and prolate spheroids, as well as spheres, for a density ratio of ten, volume fractions ranging from 0.5% to 5%, and Reynolds numbers between 20 and 30. The dynamics is determined both by the interactions of the particles with the fluid as well as by collisions, with the number and importance of collisions increasing with volume fractions. A single isolated oblate or prolate spheroid falling under gravity generally falls broadside on, for the governing parameters examined here, and at low-volume fractions, the majority of particles in a suspension fall that way. At higher-volume fractions, the orientation is more random. The slip velocity decreases as the volume fraction increases for all shapes, as expected, but the effect of the shape is much less than seen for a single particle. Furthermore, this seems to be due to two effects. For all volume fractions, the most deformed particles cluster more than spheres and less deformed particles, which increases their slip velocity. As the concentration increases, the increased particle interactions also causes more particles to fall short side-on, which reduces the frontal area and the resulting drag, increasing the slip velocity. This second effect is, of course, absent for spherical particles.

42 ENGINEERING↗
DOE OSTI2025

Spherical and sessile droplet dynamics by fluctuating hydrodynamics

We simulate the mesoscopic dynamics of droplets formed by phase-separated fluids at nanometer scales where thermal fluctuations are significant. Both spherical droplets fully immersed in a second fluid and sessile droplets which are also in contact with a solid surface are studied. Our model combines a Cahn–Hilliard formulation with incompressible fluctuating hydrodynamics; for sessile droplets, the fluid–solid contact angle is specified as a boundary condition. Deterministic simulations with an applied body force are used to measure the droplets' mobility from which a diffusion coefficient is obtained using the Einstein relation. Stochastic simulations are independently used to obtain a diffusion coefficient from a linear fit of the variance of a droplet's position with time. In some scenarios, these two measurements give the same value but not in the case of a spherical droplet initialized near a slip wall or in the case of sessile droplets with large contact angles (≥90°) on both slip and no-slip surfaces.

Bell, John B↗
DOE OSTI2025

Incorporating the molecular-scale into a hydrodynamic description of confined aqueous systems

Hydrodynamics provides a continuum-level description of fluid motion, but its applicability at the nanoscale becomes uncertain due to the emerging importance of molecular-level effects such as spatial heterogeneity. Hydrodynamic boundary conditions that incorporate molecular details allow us to partition the system into a near-wall region and a bulk fluid region. We identify a hydrodynamic wall located inside the fluid that determines where slip begins. By extending the hydrodynamic wall with the slip length, the position of the extrapolated wall is established. This offers a unified description of both slip and stagnant flow behaviors, with wall hydrophobicity characterized by the relative location of the extrapolated wall with respect to the physical wall. Employing this concept in analyses of equilibrium molecular dynamics (MD) and non-equilibrium MD simulations of Couette and Poiseuille flows, our results demonstrate consistency between equilibrium and non-equilibrium approaches across different flow types and confinement levels. This demonstrates the robust nature of linear response theory. We then explore the effects of fluid-wall and bulk fluid interactions on the hydrodynamic properties. These findings enhance the effectiveness of molecular-based simulations for investigating complex confined systems in nanofluidics, biology, and colloidal science, offering a complementary molecular-scale perspective to traditional continuum approaches.

flow simulations↗
DOE OSTI2025

High-Fidelity CFD Modeling of Cryogenic Hydrogen Isotope Extrusion for Fusion Reactor Pellet Fueling

This study investigates the extrusion processes of deuterium and protium using ANSYS-Polyflow. The geometries and computational fluid dynamics (CFD) settings closely replicate the experimental setups and data acquired from the extruder experiments at Oak Ridge National Laboratory (ORNL) for validation purposes. We explore the impacts of (1) slip versus non-slip boundary conditions and (2) the use of constant, temperature-, and shear rate–dependent viscosities, concluding that the implementation of non-slip wall boundary conditions combined with shear rate–dependent viscosity produced more accurate predictions. The simulations achieved excellent agreement with the experimental data, with relative differences of only 5% for deuterium, and 3% to 6% for protium. This is the first time that experimental extrusion data at ORNL have been accurately predicted through high-fidelity CFD modeling. In conclusion, the advancements offer valuable insights and a foundational modeling tool for optimizing pellet injectors for ITER and other future reactor-scale devices.

ANSYS-Polyflow↗
DOE OSTI2024

Androgynous { 10 1 ¯ 2 } twin in zinc

Under ambient conditions, Zn is a hexagonal metal with a large c / a ratio of 1.856. Plastic deformation is predominantly accommodated by basal 〈 a 〉 slip and compression twins on the { 10 1 ¯ 2 } planes. Increasing hydrostatic pressure drastically reduces the c / a ratio of Zn and, when a critical threshold of c / a = 3 at about 10 GPa is crossed, the { 10 1 ¯ 2 } twins are predicted to change from compressive to tensile in nature. What happens at the transition point, when c / a = 3 , remains unknown. Here, we strain-cycle a textured polycrystalline sample of pure Zn at uniform hydrostatic pressures ranging between 2 and 17 GPa, over which the c / a ratio crosses the c / a = 3 compressive-tensile transition for { 10 1 ¯ 2 } twins. During deformation, the state of the sample is monitored through x-ray diffraction to extract texture and internal strain evolution. By comparing the experimental results with the predictions of an elastoviscoplastic polycrystal simulation, we confirm the androgynous nature of { 10 1 ¯ 2 } twin response at low and high pressures. When c / a = 3 , polycrystalline Zn does not display any evidence of twinning and its plastic behavior is controlled by mostly basal and pyramidal 〈 c + a 〉 slip activity, with a very small contribution of prismatic 〈 a 〉 slip. Evidence for the activity of other { 10 1 ¯ n } twinning modes, which have been suggested for Zn under high pressure, are not observed. Published by the American Physical Society 2024

Merkel, Sébastien (ORCID:000000032767581X)↗
DOE OSTI2024

Impact of the Earthquake Rupture on Ground-Motion Variability of the 24 August 2016 M w 6.2 Amatrice, Italy, Earthquake

Here, the devastating 24 August 2016 M w 6.2 earthquake that struck Amatrice, Italy, marked the beginning of a prolonged seismic sequence dominated by three subsequent M w ≥6.0 events in the central Apennines region. The earthquake destroyed Amatrice’s historic center, claiming the lives of 299 individuals and causing widespread damage in the neighboring villages. The severity of the ground shaking, with a recorded maximum acceleration of 850 cm/s 2 on the east–west component at the Amatrice station, was far greater than the predicted acceleration based on the Italian ground-motion model (GMM). As pointed out by several investigations, the observed ground-motion amplitude and its spatial variability during the earthquake can be linked to specific rupture characteristics, including slip distribution and rupture directivity effects revealed by the observed data (Tinti et al., 2016; Pischiutta et al., 2021). In this study, we conducted physics-based 3D numerical simulations of ground motion for the Amatrice earthquake for frequencies up to 3 Hz. We employed a series of kinematic rupture models and a well-constrained local 3D velocity model incorporating surface topography. The kinematic rupture realizations were generated using multiscale hybrid and fully stochastic models, following the technique proposed by Graves and Pitarka (2016). We focused on assessing the sensitivity of near-fault ground-motion amplitudes to earthquake rupture characteristics, in particular, the spatial slip pattern. To evaluate the quality of our simulations, we employed goodness-of-fit measurements performed in comparisons of simulated and recorded ground motions. The simulated ground motions compare well with the recorded data and predictions from GMMs for Italy, ITA18 (Lanzano et al., 2019). However, we found that the simulated interevent ground-motion variability (randomness in the source process) of peak ground velocity, σ (PGV) is higher than the constant σ (PGV) predicted by conventional GMMs. Our simulations using several rupture scenarios demonstrate that the near-fault ground-motion amplification pattern is directly related to the slip distribution pattern.

3D Ground Motions Simulations↗
DOE OSTI2024

Rupture Model of the 5 April 2024 Tewksbury, New Jersey, Earthquake Based on Regional Lg -Wave Data

On 5 April 2024, an earthquake of magnitude 4.8 occurred in Tewksbury, New Jersey. It was the largest instrumentally recorded event since 1900 in New Jersey and southern New York. Millions of people around New York City, ~65 km east–northeast of Tewksbury, felt the shaking from the mainshock, but the epicentral area experienced no known significant property damages. We determine the focal mechanism, which is oblique faulting, and retrieve the Lg–wave relative source time functions (RSTFs) from the stations at regional distances to understand rupture processes and ground motions. Our fault–slip models well explain azimuthal variations of the RSTFs. The models show the rupture propagating toward the east–northeast (~50° to 60°), not along the fault strike. The slip distribution on the nodal plane striking north and dipping to the east shows a slip area of 1.1 km radius with the rupture propagating down–dip. The down–dip rupture may account for the observed lack of strong shaking in the epicentral area.

58 GEOSCIENCES↗
DOE OSTI2025

Testing horizontal momentum boundary conditions in MPAS-Ocean

A rising concern within E3SM’s MPAS-Ocean is the implementation of boundary conditions. Currently, MPAS-Ocean utilizes a no-slip boundary condition, meaning that the velocity of fluid at the boundaries is zero; however, the model should should satisfy both no-slip and free-slip boundary conditions given the correct parameters. This study focuses on testing these boundary conditions in depth, determining the accuracy of the current implementation. To accomplish this, we focus on two test cases: the barotropic gyre and barotropic channel. By manipulating parameters and comparing the numerical to corresponding analytical solutions (when available), we show that MPAS-Ocean’s ability to satisfy both boundary conditions is promising.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Chloride-Induced Stress Corrosion Cracking of Friction Stir-Welded 304L Stainless Steel: Effect of Microstructure and Temperature

Dry storage canisters of used nuclear fuels are fabricated using SUS 304L stainless steel. Chloride-induced stress corrosion cracking (CISCC) is one of the major failure modes of dry storage canisters. The cracked canisters can be repaired by friction stir welding (FSW), a low-heat input ‘solid-phase’ welding process. It is important to evaluate the ClSCC resistance of the friction stir welded material. Stress corrosion cracking (SCC) studies were carried out on mill-annealed base materials and friction stir welded 304L stainless U-bend specimens in 3.5% NaCl + 5 N H2SO4 solution at room temperature and boiling MgCl2 solution at 155 °C. The engineering stress on the outer fiber of the FSW U-bend specimen was ~60% higher than that of the base metal (BM). In spite of the higher stress level of the FSW, both materials (FSW and BM) showed almost similar SCC failure times in the two different test solutions. The SCC occurred in the thermo-mechanically affected zone (TMAZ) of the FSW specimens in the 3.5% NaCl + 5 N H2SO4 solution at room temperature, while the stirred zone (SZ) was relatively crack-free. The failure occurred at the stirred zone when tested in the boiling MgCl2 solution. Hydrogen reduction was the cathodic reaction in the boiling MgCl2 solution, which promoted hydrogen-assisted cracking of the heavily deformed stirred zone. The emergence of the slip step followed by passive film rupture and dissolution of the slip step could be the SCC events in the 3.5% NaCl + 5 N H2SO4 solution at room temperature. However, the slip step height was not sufficient to cause passivity breakdown in the fine-grained SZ. Therefore, the SCC occurred in the partially recrystallized softer TMAZ. Overall, the friction-stirred 304L showed higher tolerance to ClSCC than the 304L base metal.

304L austenitic stainless steel↗
DOE OSTI2025

CFD modeling of near-wall combustion and unburned methane prediction in natural gas spark ignition engines

Natural gas-powered engines play a critical role in gas drilling, compression, and transmission sectors, but methane (CH 4 ) from engine combustion slip can be significant over their lifespan, contributing to atmospheric pollution and signaling reduced engine efficiency. Here, to address this challenge, computational fluid dynamics (CFD) simulations offer valuable insights into the in-cylinder combustion process, enabling the optimization of combustion strategies and engine designs to minimize unburned CH 4 slip. This study aims to evaluate and improve combustion models for simulating the combustion process and predicting unburned CH 4 concentrations in natural gas spark-ignition (SI) engines, including engines that are part of combined reformer-engine systems. Specifically, the performance of two flamelet-based combustion models—the Extended Coherent Flame Model (ECFM) and the G-equation model—was assessed using experimental engine data collected under varying excess-air ratio (λ) conditions and fuel compositions, including natural gas and syngas blends. In addition, to enhance the predictive capabilities of the G-equation model, a flame-wall interaction (FWI) sub-model was integrated into its framework. The effects of its model parameters, such as quenching and influence distance, on combustion behavior and unburned methane predictions were analyzed in detail. The ECFM tended to predict delayed combustion phasing under diluted mixture conditions, resulting in overprediction of unburned CH 4 concentrations. In contrast, the G-equation model provided reasonable predictions of combustion pressure, while representing higher the CH 4 reduction rate across the operating condition compared to experimental data. Incorporating the FWI sub-model—with the quenching distance calculated based on a pressure-dependent relation (P -0.48 ) and a fixed influence distance of 1.5 mm—further improved the G-equation model’s accuracy in predicting CH 4 reduction rates without compromising its ability to simulate the combustion process.

Combustion model↗
DOE OSTI2024

Dynamic Deformation in Nuclear Graphite and Underlying Mechanisms

Time-dependent deformation in nuclear graphite is influenced by the creation and migration of radiation-induced defects in the reactor environment. This study investigates the role of pre-existing defects such as point defect clusters and Mrozowski cracks in nuclear graphite IG-110. Separate specimens were irradiated with a 2.8 MeV Au 2+ beam with a fluence of 4.38 × 10 14 cm −2 and an 8 MeV C 2+ beam with a fluence of 1.24 × 10 16 cm −2 . Microscopic specimens were either mechanically loaded inside a transmission electron microscope (TEM) or subjected to ex situ indentation-based creep loading. In situ TEM tests showed significant plasticity in regions highly localized around the Mrozowski cracks, resembling slip or ripplocation bands. Slip bands were also seen near regions without pre-existing defects but at very high stresses. Ex situ self-ion irradiation embrittled the specimens and decreased the creep displacement and rate, while heavy ion irradiation resulted in the opposite behavior. We hypothesize that the large-sized gold ions (compared to the carbon atoms) induced interplanar swelling as well as cross-plane channels for increased defect mobility. These findings illustrate the role of pre-existing defects in the dynamic relaxation of stresses during irradiation and the need for more studies into the radiation environment’s impact on the mechanical response of nuclear graphite.

creep deformation↗
DOE OSTI2025

Dislocation‐Driven Formation of Oriented Macroperiodic Metastructures of Curved Single Crystal Lattices in Glass

Abstract Single crystals fabricated in glass by localized heating can develop uniquely deformed lattices stabilized by the surrounding amorphous medium. The development of lattice curvature appears to be intrinsic to the crystal growth process in some systems, while the result of the locally changing crystallography in others. In this work, a model laser‐fabricated rotating lattice Sb 2 S 3 crystal grown in stoichiometric glass is used to demonstrate fabrication of novel macroperiodic metastructures that utilize intrinsic lattice curvature superimposed with subtle crystallographic influences. The limited availability of slip systems drives the lattice curvature magnitude to vary with crystal growth direction, maximizing for lattices aligned with the predominant Burgers vector along with corresponding increases in dislocation density. Misaligned lattice orientations form smaller secondary lattice curvatures arising from misaligned Burgers vectors with further elastic contributions. Over extended crystal growth, these secondary components align the lattice to rotate about either the <001> or <010> crystal axes forming repeating metastructures of lattice orientation with periodicity 20–160 microns in length. The mechanistic approach used in this work may be expanded to other systems with known slip systems to better understand and design macroperiodic metastructures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simultaneous Optimization of Crystal Plasticity Hardening Parameters

Crystal plasticity models relate macroscopic deformation behavior to the evolution of slip systems strength, but their parameterization is often non-unique, with multiple parameter sets being able to describe the same macroscopic behavior. To address this issue, the present work adopts a Bayesian optimization framework for the parameterization of face-centered cubic plasticity models while simultaneously considering multiple experimental datasets from the literature. For single crystal Cu, parameter optimization was guided by the tensile stress–strain curves along several crystallographic orientations, with an adequate fit being found for five orientations at once. While additional parameters allowed for the consideration of more physical mechanisms, like different slip system interaction strengths or misorientations inherent to the experimental data, the extra dimensionality was found to limit the efficiency of the global minimization procedure. For polycrystalline Ni, multiple grain sizes were considered together in a representative polycrystalline model, with the optimization able to reconcile the model with the data for three grain sizes at once. As meaningful interpretation of parameters relies on the uniqueness of their values, incorporating multiple datasets into this discerning parameterization procedure enables more robust prediction and application of crystal plasticity models.

36 MATERIALS SCIENCE↗