Search NASA⌕ Search

SEARCH · Search NASA

Results for “Solid state oxidation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

High Temperature Thick Film Sensor Development Based on Refractory Oxide Semiconductors

Solid-state, high-temperature sensing devices are required for accurate temperature, strain/stress, and failure monitoring for a range of advanced manufacturing, transportation, and military applications. High temperature conditions limit sensing strategies, where typically traditional metal and semiconductor materials are unstable, and the sensing options are limited to optical spectroscopy methods. In addition, strategies to embed the sensors directly within active components and protective thermal refractory are of interest that permit near-environment sensing which is not possible with the traditional electronic materials and components. Rare-earth chromite semiconductors exhibit some properties of interest for high temperature sensing technologies, such as: high microstructure and chemical stability, relatively high electronic conductivity at high temperatures, and relative thermal expansion coefficient matching to refractory thermal protective insulation (such as high-zirconia and -alumina ceramics). In this work, n-type and p-type doped lanthanum chromites compositions were computationally modelled and prepared, and the electrical, thermoelectric, and thermomechanical properties were measured for the obtained material systems. A few compositions were then processed into thick film health and temperature sensors and tested at high temperatures. To establish relative stability under harsh environment conditions, post- mortem microstructure and chemical composition was characterized after extended and cycle testing at high temperatures.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Review of Solid State Consolidation Processing Techniques of ODS Steels (Hot Extrusion, Hot Isostatic Pressing, Spark Plasma Sintering, and Stir Friction Consolidation): Resulting Microstructures and Mechanical Properties

This paper reviews the solid-state consolidation processing techniques for Oxide Dispersion Strengthened steels and compares them in terms of the resulting microstructure and reported mechanical properties. Synthesis techniques include hot extrusion, hot isostatic pressing, spark plasma sintering and friction consolidation. The effects of process parameters on the resulting microstructures and performance are discussed for each technique. Average oxide size, average grain size, and porosity are compared across techniques, as well as mechanical strength and ductility. Across consolidation techniques where temperature can be controlled, a low sintering temperature with a high sintering pressure is favorable for keeping oxide sizes, grain sizes, and porosity low. The use of yttrium and titanium for oxide formation has been evidenced to reduce oxide sizes, and tungsten additions have been shown to improve strength. Current literature suggests that the more mature hot extrusion technique produces stronger steel with consistently fine oxides, while other alternative solid-state consolidation, while promising, offer margin for improvement.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Probing the elastic modulus and hardness of superionic boron cluster solid electrolytes

Polyhedral borane salts are highly tunable compounds with the potential to be used as solid electrolytes due to their high Li and Na superionic conductivity and relatively wide electrochemical stability window. In considering their application to all solid-state batteries, their mechanical properties play a critical role in their operation due to stresses the solid electrolyte is subjected to during battery operation. Density functional theory (DFT) calculations have provided an initial assessment of bulk and elastic moduli for some selected boron cluster solid electrolytes, but direct measurements are still scarce. Here, in this paper, we report the elastic moduli and hardnesses of LiCB 11 H 12 , LiCB 9 H 10 , NaCB 11 H 12 , and NaCB 9 H 10 for the first time using nanoindentation continuous stiffness method (CSM) measurements under inert atmosphere. Experimental modulus values ranging 8.8–12.3 GPa and hardness values ranging 0.15–0.38 GPa are lower than that of other inorganic solid-state electrolytes such as oxide- and sulfide-based solid electrolytes. DFT calculations on the expected moduli of these compounds are also presented and discussed. Analysis of the indentation plasticity index reveals that these compounds have higher plasticity index compared to other common oxide and sulfide solid electrolytes. According to the calculated Pugh's ratio, all compounds in this study except LiCB 11 H 12 are considered ductile.

25 ENERGY STORAGE↗
DOE OSTI2021

SISGR: Chemomechanics of Far-From-Equilibrium Interfaces (COFFEI)

Portable, reliable, and deployable devices for energy storage and conversion require fundamental changes in design of solid-state composites comprising ceramics and metals. These materials comprise the electrodes and electrolytes of next-generation solid-oxide fuel cells and all solid-state batteries, forming solid-state functional composites. The advent of solid-state batteries – which replace liquid electrolytes with solid electrolytes capable of lithium ion transport for reliable energy storage in portable batteries – and the increased demand space for all solid-state fuel cells capable of oxygen reduction at intermediate temperatures remain important challenges for improved material stability and decreased system cost. However, little is understood about three fundamental facets of materials that enable such solid-state energy applications. First, how do such materials deform, fracture, or delaminate under operando conditions? Second, how does such mechanical deformation limit or facilitate electronic and ionic transport within and across such material interfaces? Third, how we can predictably design interface-rich composites to engineer both structural and electrochemical stability? This COFFEI Group comprised expertise from Materials Science & Engineering and Nuclear Science & Engineering to integrate unique in situ experiments, simulations, and fabricated interfaces that address these fundamental questions in solid-state interfaces of nanoscale composites that will guide solid-state electrochemistry, transport kinetics, and mechanical deformation for nonstoichiometric materials that enable such applications. In particular, we built on COFFEI’s understanding of chemomechanical coupling among defect concentrations, ionic transport, electron transport, and stored elastic energy that is particularly acute in the far-from-equilibrium conditions typical of energy device applications. By tailoring our focus to solid-state interfaces, we addressed these important issues by (a) developing and applying advanced in situ and ex situ characterization tools to characterize model materials and interfaces synthesized with molecular-level control, under both laboratory-controlled and extreme environments representative of energy device operation; and (b) employing computational modeling and simulation frameworks to predict transport mechanisms, reactivity and stability of these model materials and interfaces under significant chemical strains typical of energy device operation. Recent progress provided insights to additional materials systems and electrochemomechanical fatigue and fracture that were not fully envisioned when the program was initiated. Specifically, in the final three years of COFFEI we pursued two integrated thrusts, with complementary focus. Thrust I focused on failure-resistant electrochemomechanical composites, while Thrust II focused on strain-modulated conductivity and reactivity across interfaces. In contrast to our initial COFFEI focus, these thrusts concentrated wholly on solid-state material interfacial interactions and included greater integration of multiscale visualization including in situ electron microscopy of strained structures/interactions and mesoscale simulations. Successful development of functionally superior and long-lived battery and fuel cell systems and stress adaptable oxides requires a deeper, fundamental understanding of the coupling among the historically important subfields of solid-state electrochemistry, transport kinetics, and mechanical deformation for nonstoichiometric metal oxide electrodes. In this program, the understanding and the application of chemomechanical coupling of defect concentrations, ionic transport, electro-catalytic activity and stored elastic energy, particularly acute in the far-from-equilibrium conditions typical of energy device applications, are being refined and implications for device operation clarified, including for miniaturized solid-state batteries and fuel cells.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Demonstration of Electroreduction Technology to Convert GNF Uranium Oxide Powder to Metal

Global Nuclear Fuel – Americas LLC (GNF) has partnered with Argonne National Laboratory to demonstrate electroreduction of uranium oxides produced by deconversion of UF 6 to uranium metal through the Gateway for Accelerated Innovation in Nuclear (GAIN) program under the U.S. Department of Energy to accelerate the domestic production of metallic advanced reactor fuels. Electroreduction of uranium oxide was first demonstrated and patented by Argonne in the early 2000s as a technology to convert used oxide nuclear fuel from light water reactors to metal for further fuel reprocessing. More recently, electroreduction has been proposed as a front-end technology for metallization of uranium oxides produced by deconversion of UF 6 and for scrap recovery of oxide materials. During the electroreduction process, UO 2 powder is contained in a stainless-steel mesh basket with a cathode lead located in the center of the UO 2 bed. The basket is immersed in lithium chloride molten salt electrolyte containing 1 wt% lithium oxide along with a platinum anode and a nickel/nickel oxide (Ni/NiO) reference electrode. Current is applied to the cell between the cathode and anode to reduce the UO 2 to metallic uranium via a solid-state reduction reaction. Oxide ions released from the UO 2 during reduction are transported through the salt to the anode where oxygen gas is evolved. Once reduction is complete, the basket containing the metallicized uranium is removed from the salt and can be processed to remove the salt and consolidate the uranium into an ingot for use in metallic fuel fabrication. This project was performed to provide evidence of the electroreduction technology readiness level for metallization of UO 2 powder, identify and retire technical risks for industrialization of electroreduction, and accelerate the path to commercialization for metallic fast reactor fuel production. To that end, five electroreduction tests were performed with UO 2 provided by GNF and the resulting product was analyzed for the extent of conversion to metal and for impurity contents of the metal product to verify that electroreduction does not introduce impurities that would prevent use of the product in metallic fuel fabrication.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1971

Moessbauer spectra of ferrite catalysts used in oxidative dehydrogenation

Room temperature Mossbauer spectroscopy was used to examine bulk changes which occur in low surface area CoFe2O4 and CuFe2O4 catalysts as a result of contact with various mixtures of trans-2-butene and O2 during oxidative dehydrogenation reactions at about 420 C. So long as there was at least some O2 in the gas phase, the CoFe2O4 spectrum was essentially unchanged. However, the spectrum changed from a random spinel in the oxidized state to an inverse spinel as it was reduced by oxide ion removal. The steady state catalyst lies very near the fully oxidized state. More dramatic solid state changes occurred as the CuFe2O4 underwent reduction. Under severe reduction, the ferrite was transformed into Cu and Fe3O4, but it could be reversibly recovered by oxidation. An intense doublet located near zero velocity persisted in all spectra of CuFe2O4 regardless of the state of reduction.

Cares, W. R.↗
DOE OSTI2024

Crack‐Free Single‐Crystalline LiNiO 2 for High Energy Density All‐Solid‐State Batteries

Abstract Single‐crystalline layered oxide (LiNi 1‐ x ‐ y Mn x Co y O 2 ) cathodes have been found to exhibit exceptional electrochemical properties when coupled with various inorganic solid electrolytes (ISEs) in all‐solid‐state batteries (ASSBs). Their advantages stem from the robust morphological integrity with the absence of grain boundaries and the high electrochemical oxidative stability. Here, ASSBs featuring single‐crystalline LiNiO 2 (LNO) with the highest Ni content are reported, offering a high theoretical specific capacity of 275 mAh g ‐1 alongside a high average discharge voltage (3.7 V vs Li + /Li). Through a careful investigation, it is demonstrated that micron‐sized single‐crystalline LNO (µSC‐LNO) composite cathodes with a halide ISE exhibit a high initial discharge capacity of 205 mAh g ‐1 with an outstanding cycle performance over 200 cycles in room‐temperature ASSBs. The significance of engineering parameters is emphasized, such as particle size and specific density, in promoting a homogeneous and fast Li + transport within the composite cathodes. Furthermore, the formation of undesirable interphase between the halide ISE in the cathode and sulfide ISE separator is elucidated, which may be a critical factor impeding long‐term cyclability of ASSBs. This work provides insights into the design of composite cathodes for high‐energy‐density ASSBs.

Chemistry↗
DOE OSTI2020

Interactions of Oxide Surfaces with Water Revealed with Solid-State NMR Spectroscopy

Hydrous materials are ubiquitous in the natural environment and efforts have previously been made to investigate the structures and dynamics of hydrated surfaces for their key roles in various chemical and physical applications, with the help of theoretical modeling and microscopy techniques. However, an overall atomic-scale understanding of the water–solid interface, including the effect of water on surface ions, is still lacking. Herein, we employ ceria nanorods with different amounts of water as an example and demonstrate a new approach to explore the water–surface interactions by using solid-state NMR in combination with density functional theory. NMR shifts and relaxation time analysis provide detailed information on the local structure of oxygen ions and the nature of water motion on the surface: the amount of molecularly adsorbed water decreases rapidly with increasing temperature (from room temperature to 150 °C), whereas hydroxyl groups are stable up to 150 °C, and dynamic water molecules are found to instantaneously coordinate to the surface oxygen ions. Additionally, the applicability of dynamic nuclear polarization for selective detection of surface oxygen species is also compared to conventional NMR with surface selective isotopic-labeling: the optimal method depends on the feasibility of enrichment and the concentration of protons in the sample. These results provide new insight into the interfacial structure of hydrated oxide nanostructures, which is important to improve performance for various applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Navigating phase diagram complexity to guide robotic inorganic materials synthesis

Abstract Efficient synthesis recipes are needed to streamline the manufacturing of complex materials and to accelerate the realization of theoretically predicted materials. Often, the solid-state synthesis of multicomponent oxides is impeded by undesired by-product phases, which can kinetically trap reactions in an incomplete non-equilibrium state. Here we report a thermodynamic strategy to navigate high-dimensional phase diagrams in search of precursors that circumvent low-energy, competing by-products, while maximizing the reaction energy to drive fast phase transformation kinetics. Using a robotic inorganic materials synthesis laboratory, we perform a large-scale experimental validation of our precursor selection principles. For a set of 35 target quaternary oxides, with chemistries representative of intercalation battery cathodes and solid-state electrolytes, our robot performs 224 reactions spanning 27 elements with 28 unique precursors, operated by 1 human experimentalist. Our predicted precursors frequently yield target materials with higher phase purity than traditional precursors. Robotic laboratories offer an exciting platform for data-driven experimental synthesis science, from which we can develop fundamental insights to guide both human and robotic chemists.

Chen, Jiadong (ORCID:0009000476038838)↗
DOE OSTI2020

Semiconducting Small Molecules as Active Materials for p-Type Accumulation Mode Organic Electrochemical Transistors

A series of semiconducting small molecules with bithiophene or bis-3,4-ethylenedioxythiophene cores are designed and synthesized. The molecules display stable reversible oxidation in solution and can be reversibly oxidized in the solid state with aqueous electrolyte when functionalized with polar triethylene glycol side chains. Evidence of promising ion injection properties observed with cyclic voltammetry is complemented by strong electrochromism probed by spectroelectrochemistry. Blending these molecules with high molecular weight polyethylene oxide (PEO) is found to improve both ion injection and thin film stability. The molecules and their corresponding PEO blends are investigated as active layers in organic electrochemical transistors (OECTs). For the most promising molecule:polymer blend (P4E4:PEO), p-type accumulation mode OECTs with µA drain currents, μS peak transconductances, and a µC* figure-of-merit value of 0.81 F V -1 cm -1 s -1 are obtained.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Evaluating the bond strength and fracture mechanisms of cold-sprayed zinc coating on AZ91 magnesium substrate via a combined experimental and computational approach

Magnesium (Mg) alloys are ideal candidates for automotive applications due to their high strength to weight ratio, castability, recyclability etc., however, they lack corrosion and oxidation resistance. Solid-state deposition techniques, such as cold spray, have been demonstrated to enhance their corrosion resistance as it relies on the severe plastic deformation of powder particles upon impact with the substrate to form a metallurgical bond with the substrate and within the coating. At cold sprayed interfaces, a heterogeneous microstructure is formed that includes some porosity, oxides and intermetallics which can significantly affect coating performance. Thus, establishing a direct correlation between the interface microstructure and its properties can aid in designing optimal cold spray parameters. In this study, we investigated the microstructure and mechanical properties of a zinc (Zn) coating deposited on a high pressure die cast (HPDC) AZ91 Mg substrate via high resolution scanning transmission electron microscopy, in situ micro-tensile testing, and finite element method (FEM) modeling. Micro-tensile pillars fabricated using the plasma focused ion beam (PFIB) successfully isolates the coating-substrate interface within the gauge length. The average bond strength of Zn-Mg interface was determined to be ∼140 MPa with failure occurring partially at the interface and mostly into the coatings. A detailed microstructural characterization revealed evidence of a strong metallurgical bonding at the Zn-Mg interface and formation of the C14 MgZn 2 laves phase interlayer resulting in a mixed mode of fracture during the micro-tensile experiments. FEM modeling reveals the stress distribution along the interfaces and suggests that a MgZn 2 layer thickness between 200–400 nm is optimum to increase the bond strength and minimize the triaxiality. Such a site-specific interfacial analysis with correlative computational modeling provides crucial insight into the overall performance of cold spray interfaces.

Bond strength↗
DOE OSTI2023

Engineering Functionalized 2D Metal-Organic Frameworks Nanosheets with Fast Li + Conduction for Advanced Solid Li Batteries

Solid-state batteries can ensure high energy density and safety in lithium metal batteries, while polymer electrolytes are plagued by slow ion kinetics and low selective transport of Li + . Metal-organic frameworks (MOFs) are proposed as emerging fillers for solid-state poly(ethylene oxide)(PEO) electrolytes, however, developing functionalized MOFs and understanding their roles on ion transfer has proven challenging. Herein, combining computational and experimental results, the functional group regulation in MOFs can effectively change surficial charge distribution and limit anion movement is revealed, providing a potential solution to these issues. Specifically, functionalized 2D MOF sheets are designed through molecular engineering to construct high-performance composite electrolytes, where the electron-donating effect of substituents in 2D-MOFs effectively limits the movement of ClO 4 - and promotes mechanical properties and ion migration numbers (0.36 up to 0.64) of PEO. As a result, Li/Li cells with composite electrolyte exhibit superior cyclability for 1000 h at a current density of 0.2 mA cm -2 . Meanwhile, the solid LiFePO 4 /Li battery delivers highly reversible capacities of 148.8 mAh g -1 after 200 cycles. In conclusion, these findings highlight a new approach for anion confinement through the use of functional group electronic effects, leading to enhanced ionic conductivity, and a feasible direction for high-performance solid-state batteries.

25 ENERGY STORAGE↗
DOE OSTI2020

Unveiling the critical role of interfacial ionic conductivity in all-solid-state lithium batteries

Advancement of all-solid-state lithium-ion (Li + ) batteries (ASSLIBs) has been hindered by the large interfacial resistance mainly originating from interfacial reactions between oxide cathodes and solid-state sulfide electrolytes (SEs). To suppress the interfacial reactions, an interfacial coating layer between cathodes and SEs is indispensable. However, the kinetics of interfacial Li + transport across the coating layer has not been well understood yet. Herein, we tune the interfacial ionic conductivity of the coating layer LiNb 0.5 Ta 0.5 O 3 (LNTO) by manipulating post-annealing temperature. It is found that the interfacial ionic conductivity determines interfacial Li + transport kinetics and enhancing the interfacial ionic conductivity can significantly boost the electrochemical performance of SE-based ASSLIBs. A representative cathode LiNi 0.5 Mn 0.3 Co 0.2 O 2 coated by LNTO with the highest interfacial ionic conductivity exhibits a high initial capacity of 152 mAh.g -1 at 0.1 C and 107.5 mAh.g -1 at 1C. This work highlights the importance of increasing interfacial ionic conductivity for high-performance SE-based ASSLIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Simulated field-modulated x-ray absorption in titania

Here, we present a method to compute the x-ray absorption near-edge structure (XANES) spectra of solid-state transition metal oxides using real-time time-dependent density functional theory, including spin–orbit coupling effects. This was performed on bulk-mimicking anatase titania (TiO 2 ) clusters, which allows for the use of hybrid functionals and atom-centered all electron basis sets. Furthermore, this method was employed to calculate the shifts in the XANES spectra of the Ti L-edge in the presence of applied electric fields to understand how external fields can modify the electronic structure, and how this can be probed using x-ray absorption spectroscopy. Specifically, the onset of t 2g peaks in the Ti L-edge was observed to red shift and the e g peaks were observed to blue shift with increasing fields, attributed to changes in the hybridization of the conduction band (3d) orbitals.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

In Situ Visualization of the Pinning Effect of Planar Defects on Li Ion Insertion

Longevity of Li ion batteries strongly depends on the interaction of transporting Li ions in electrode crystals with defects. However, detailed interactions between the Li ion flux and structural defects in the host crystal remain obscure due to the transient nature of such interactions. Here, by in situ transmission electron microscopy and density function theory calculations, we reveal how the diffusion pathways and transport kinetics of a Li ion can be affected by planar defects in a tungsten trioxide lattice. We uncover that changes in charge distribution and lattice spacing along the planar defects disrupt the continuity of ion conduction channels and dramatically increase the energy barrier of Li diffusion, thus, arresting Li ions at the defect sites and twisting the lithiation front. In conclusion, the atomic-scale understanding holds critical implications for rational interface design in solid-state batteries and solid oxide fuel cells.

25 ENERGY STORAGE↗