Search NASA⌕ Search

SEARCH · Search NASA

Results for “Strain characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Characterization of High Strain Rate Mechanical behavior of AZ31 magnesium alloy using 3D Digital Image Correlation

Characterization of the material mechanical behavior at sub-Hopkinson regime (0.1 to 1000 s{sup -1}) is very challenging due to instrumentation limitations and the complexity of data analysis involved in dynamic loading. In this study, AZ31 magnesium alloy sheet specimens are tested using a custom designed servo-hydraulic machine in tension at nominal strain rates up to 1000 s{sup -1}. In order to resolve strain measurement artifacts, the specimen displacement is measured using 3D Digital Image correlation instead from actuator motion. The total strain is measured up to {approx} 30%, which is far beyond the measurable range of electric resistance strain gages. Stresses are calculated based on the elastic strains in the tab of a standard dog-bone shaped specimen. Using this technique, the stresses measured for strain rates of 100 s{sup -1} and lower show little or no noise comparing to load cell signals. When the strain rates are higher than 250 s{sup -1}, the noises and oscillations in the stress measurements are significantly decreased from {approx} 250 to 50 MPa. Overall, it is found that there are no significant differences in the elongation, although the material exhibits slight work hardening when the strain rate is increased from 1 to 100 s{sup -1}.

36 MATERIALS SCIENCE↗

Non-destructive depth-resolved characterization of residual strain fields in high electron mobility transistors using differential aperture x-ray microscopy

Localized residual stress and elastic strain concentrations in microelectronic devices often affect the electronic performance, resistance to thermomechanical damage, and, likely, radiation tolerance. A primary challenge for the characterization of these concentrations is that they exist over sub-μm length-scales, precluding their characterization by more traditional residual stress measurement techniques. Here, in this study, we demonstrate the use of synchrotron x-ray-based differential aperture x-ray microscopy (DAXM) as a viable, non-destructive means to characterize these stress and strain concentrations in a depth-resolved manner. DAXM is used to map two-dimensional strain fields between the source and the drain in a gallium nitride (GaN) layer within high electron mobility transistors (HEMTs) with sub-μm spatial resolution. Strain fields at various positions in both pristine and irradiated HEMT specimens are presented in addition to a preliminary stress analysis to estimate the distribution of various stress components within the GaN layer. γ-irradiation is found to significantly reduce the lattice plane spacing in the GaN along the sample normal direction, which is attributed to radiation damage in transistor components bonded to the GaN during irradiation.

42 ENGINEERING↗

AFRL Additive Manufacturing Modeling Series: Challenge 1, Characterization of Residual Strain Distribution in Additively-Manufactured Metal Parts Using Energy-Dispersive Diffraction

A machine component fabricated by additive manufacturing (AM) of metal powders often possesses steep residual stress gradients with significant magnitudes due to large temperature gradients that transpire within a localized area during fabrication. These processing-induced residual stresses can cause distortion of the part, and if they are of significant magnitude, they could induce cracking of the component, degrade printability, and/or diminish subsequent mechanical performance. The ability to predict these residual stresses imparted by AM is an important step in permeating AM technology for advanced manufacturing. Calibration and validation of AM process models used for prediction are, therefore, a critical step in understanding the origin and mitigating the challenges associated with residual stresses inherent to the AM process. In the present work, the residual strain distributions in components with simple geometries fabricated by a laser powder bed fusion (LBPF) process were characterized non-destructively using energy-dispersive X-ray diffraction in support of the US Air Force Research Laboratory Additive Manufacturing Modeling Challenge Series Groeber et al. (JOM 70:441-448, 2018). The measurement setup and approach are described in detail so that the data can be used as a benchmark to calibrate and validate models for the prediction of macro-scale residual stresses due to the LPBF process.

36 MATERIALS SCIENCE↗

New Strainmeters used to Monitor Deformation During Injection and Withdrawal

Injecting or removing fluids from reservoirs or aquifers causes deformation that can be used as a diagnostic signal in some cases, while it can interfere with geodetic interpretations in other cases. This has motivated us to develop instrumentation and methods to characterize the strain field resulting from injection and pumping. Three new instruments have been deployed at our field stations near Clemson University and at the Avant Field north of Tulsa, OK. Two use non-contact eddy current transducers configured to measure four components of strain and two tilts to 1 part-per-billion. One system is designed for permanent installation, the other is removable for short term deployments. Another system is a low cost volumetric strainmeter consisting of an embedded optical fiber that is interrogated using laser interferometry. This strainmeter is designed to be a permanently installed and has a resolution of several parts-per-trillion. The field sites are designed to characterize strains during pumping or injection over different scales and in different geologic settings. The Clemson field station is underlain by biotite gneiss, a low permeability crystalline rock overlain by moderate permeability, soft saprolite above 30m depth. The water table is at approximately 9m depth. The strainmeters are in the crystalline rock at approximately 40m depth, and pumping occurs in the overlying saprolite. In contrast, wells at the Avant Field site are much deeper. They are approximately 500m deep and completed in a 25-m-thick oil-bearing sandstone. Strainmeters at the Avant Field are at ~30m depth. These two sites provide contrasting approaches to characterizing strain at 30-40m depth. Water is pumped from an overlying formation at the Clemson site, whereas it is pumped from a much deeper underlying formation at the Avant Field. Preliminary results are available from a brief injection test, and from a longer shut-in test at the Avant Field. Injection is characterized by an increase in tensile strains in both the radial and circumferential directions approximately 220m from the well. The shut-in was characterized by radial tension and circumferential compression in response to a well approximately 1km from the strainmeter. These are the expected signals caused by injection and shut-in according to poroelastic simulations.

DeWolf, Scott↗

Using the Shallow Strain Tensor to Characterize Deep Geologic Reservoirs

Abstract Storing and recovering water, carbon, and heat from geologic reservoirs is central to managing resources in a changing climate. We tested the hypothesis that the strain tensor caused by injecting or producing fluids can be measured at shallow depths and interpreted to advance understanding of underlying deep aquifers or reservoirs. Geodetic‐grade strainmeters were deployed at 30 m depth overlying the Bartlesville Formation, a 500‐m‐deep sandstone near Tulsa, OK. The strainmeters are 220 m east of injection well 9A completed in a permeable lens at the base of the Bartlesville Formation. Water was injected into well 9A at approximately 1.0 L/s during four tests that ranged in duration from a few hours to a few weeks. The horizontal strain increased (tension) and the circumferential strain was a few times larger than the radial strain. The vertical strain decreased (compression) during injection. Strain rates were approximately 100 nε/day during the first few hours, but the rates decreased and were approximately 10 nε/day during most of the tests. Four independent methods of poroelastic simulation and inversion predict reservoir properties and geometries that are similar to each other and consistent with independent information about the reservoir. All strain interpretations predict that a boundary to the permeable lens occurs beneath the vicinity of the strainmeters, which is consistent with core data from the site. The boundary of the permeable lens is located by matching the vertical, radial and circumferential strains, which demonstrates the value of measuring the strain tensor.

Murdoch, Lawrence C.↗

The survivor strain: isolation and characterization of Phormidium yuhuli AB48, a filamentous phototactic cyanobacterium with biotechnological potential

Despite their recognized potential, current applications of cyanobacteria as microbial cell factories remain in early stages of development. This is partly due to the fact that engineered strains are often difficult to grow at scale. This technical challenge contrasts with the dense and highly productive cyanobacteria populations thriving in many natural environments. It has been proposed that the selection of strains pre-adapted for growth in industrial photobioreactors could enable more productive cultivation outcomes. Here, we described the initial morphological, physiological, and genomic characterization of Phormidium yuhuli AB48 isolated from an industrial photobioreactor environment. P. yuhuli AB48 is a filamentous phototactic cyanobacterium with a growth rate comparable to Synechocystis sp . PCC 6803. The isolate forms dense biofilms under high salinity and alkaline conditions and manifests a similar nutrient profile to Arthrospira platensis ( Spirulina ). We sequenced, assembled, and analyzed the P. yuhuli AB48 genome, the first closed circular isolate reference genome for a member of the Phormidium genus. We then used cultivation experiments in combination with proteomics and metabolomics to investigate growth characteristics and phenotypes related to industrial scale cultivation, including nitrogen and carbon utilization, salinity, and pH acclimation, as well as antibiotic resistance. These analyses provide insight into the biological mechanisms behind the desirable growth properties manifested by P. yuhuli AB48 and position it as a promising microbial cell factory for industrial-scale bioproduction[221, 1631].

59 BASIC BIOLOGICAL SCIENCES↗

Characterization and Strain-Hardening Behavior of Friction Stir-Welded Ferritic Stainless Steel

In this study, friction stir-welded joint of 3-mm-thick plates of 409 ferritic stainless steel (FSS) was characterized in light of microstructure, x-ray diffraction analysis, hardness, tensile strength, ductility, corrosion and work hardening properties. The FSW joint made of ferritic stainless steel comprises of three distinct regions including the base metal. In stir zone highly refined ferrite grains with martensite and some carbide precipitates at the grain boundaries were observed. X-ray diffraction analysis also revealed precipitation of Cr{sub 23}C{sub 6} and martensite formation in heat-affected zone and stir zone. In tensile testing of the transverse weld samples, the failure eventuated within the gauge length of the specimen from the base metal region having tensile properties overmatched to the as-received base metal. The tensile strength and elongation of the longitudinal (all weld) sample were found to be 1014 MPa and 9.47%, respectively. However, in potentiodynamic polarization test, the corrosion current density of the stir zone was highest among all the three zones. The strain-hardening exponent for base metal, transverse and longitudinal (all weld) weld samples was calculated using various equations. Both the transverse and longitudinal weld samples exhibited higher strain-hardening exponents as compared to the as-received base metal. In Kocks–Mecking plots for the base metal and weld samples at least two stages of strain hardening were observed.

36 MATERIALS SCIENCE↗

High Strain Rate Mechanical Characterization of Carbon Fiber Reinforced Polymer Composites Using Digital Image Correlations

We present that the introduction of carbon fiber reinforced polymer (CFRP) composites to structural components in lightweight automotive structures necessitates an assessment to evaluate that their crashworthiness dynamic response provides similar or higher levels of safety compared to conventional metallic structures. In order to develop, integrate and implement predictive computational models for CFRP composites that link the materials design, molding process and final performance requirements to enable optimal design and manufacturing vehicle systems for this study, the dynamic mechanical response of unidirectional (UD) and 2x2 twill weave CRFP composites was characterized at deformation rates applicable to crashworthiness performance. Non-standardized specimen geometries were tested on a standard uniaxial frame and an intermediate-to-high speed dynamic testing frame, equipped with high speed cameras for 3D digital image correlation (DIC). Specimen cross-sections, according to each fiber orientation tested, were consistent across strain rates to ensure results were comparable. Tensile strength and modulus were experimentally investigated over a wide range of strain rates (0.0001 to 200 s -1 ). DIC was used to estimate strain profiles on composites surfaces, and the modulus was calculated from those strain measurements. Experimental results demonstrated an increase in the tensile strength of UD CFRP composites in the longitudinal (0°) and transverse (90°) direction with increasing strain rates. In contrast, the tensile strength of 2x2 woven composites and the tensile modulus of the UD material were insensitive to increasing strain rates. Finally, comparison of failure modes provided insights on how loading rates influenced failure mechanisms.

36 MATERIALS SCIENCE↗

HolT Hunter: Software for Identifying and Characterizing Low-Strain DNA Holliday Triangles

Synthetic DNA nanostructures are most commonly held together via Holliday junctions. These junctions allow for a wide variety of different angles between the double helices they connect. Nevertheless, only constructs with a very limited selection of angles have been built, to date, because of the computational complexity of identifying structures that fit together with low strain at odd angles. I have developed an algorithm that finds over 95% of the possible solutions by breaking the problem down into two portions. First, there is a problem of how smooth rods can form triangles by lying across one another. This problem is easily handled by numerical computation. Second, there is the question of how distorted DNA double helices would need to be to fit onto the rod structure. This strain is calculated directly. The algorithm has been implemented in a Mathematica 8 notebook called Holliday Triangle Hunter. A large database of solutions has been identified. Additional interface software is available to facilitate drawing and viewing models.

59 BASIC BIOLOGICAL SCIENCES↗

Microstructural Characterization and High Strain Rate Plastic Flow Behavior of SMAW Armox500T Steel Joints from Spherical Indentation Experiments

Static indentation and uniaxial compression tests have been conducted on Armox500T steel and its weldments to predict the constraint factor (CF), i.e., ratio of Meyer’s hardness to uniaxial flow stress. Series of dynamic indentation experiments were carried out at impact velocities ranging from 5 to 300 m/s to estimate dynamic hardness as a function of average strain. Subsequently, dynamic indentation (DI) test data and CF determined under static indentation conditions have been used to study the high strain rate plastic flow behavior of Armox500T weldments in comparison with the base metal. It was observed that flow stress for Armox500T and its weldments under dynamic loading conditions (10{sup 4} s{sup −1}) are significantly higher than flow stress measured under static loading conditions (10{sup −3} s{sup −1}). The plastic flow behavior computed from DI is in good agreement with the data evaluated through conventional split Hopkinson pressure bar technique. Further, the study of the microstructure of base metal and weldments by optical microscopy and SEM revealed a considerable variation in the microstructure.

36 MATERIALS SCIENCE↗

Characterization of vertical strain silicon MOSFET incorporating dielectric pocket (SDP-VMOSFET)

The vertical Metal-Oxide-Semiconductor Field-Effect-Transistor (MOSFET) leads to a double channel width that can increase the packaging density. The strained silicon MOSFET was introduced to modify the carrier transport properties of silicon in order to enhance transport of both electrons and holes within strained layer. Dielectric pocket was act to control encroachment of the drain doping into the channel and reduce short channel effects (SCE). SDP-VMOSFET which was a combination of those advantages was proposed to overcome the SCE in term of leakage current, threshold voltage roll-off also Drain Induce Barrier Lowering (DIBL). As a result, SDP-VMOSFET produces a better threshold voltage and DIBL compared to related structures. Meanwhile, it gives slightly increased for leakage current compared to Vertical MOSFET Incorporating Dielectric Pocket. The characteristics of the SDP-VMOSFET are analyzed in order to optimize the performance of the device and leading to the next generation of IC technology.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nano-scale characterization of GaAsP/GaAs strained superlattice structure by nano-beam electron diffraction

Distribution of lattice strain in a GaAsP/GaAs superlattice with a periodicity of 10 nm thickness, deposited on a 100 nm GaAs basal layer has been measured by nano-beam electron diffraction. The superlattice on the (001) plane of the basal GaAs layer shows a constant lattice strain from the bottom to the top layers, whereas the superlattice on the basal GaAs surface sloped by 16° from the (001) plane shows a variation of the lattice strain and crystal orientation. The difference of the strain distributions was discussed from the viewpoint of average strain. This tilt was explained by an atomistic model.

36 MATERIALS SCIENCE↗

Applied genomics for industrially relevant microalgal strain development & optimization: characterizing genotype-phenotype relationships towards scalable environment-enhancing energy systems

Multiple planetary boundaries considered a safe operating space for humanity have been exceeded in recent years, with twice as many boundaries transgressed in 2023 as in 2009. Bioenergy systems are unique in that they can interact with and improve many of the transgressed boundaries directly, including multiple geochemical cycles, water and land use, and climate change. Among bioenergy systems, microalgae-based environment enhancing energy (E 2 -energy) are promising bioenergy systems for drop-in biofuels, valuable materials, chemicals and therapeutics, while making deep emission cuts and remediating wastewater, all without competing for agricultural resources.

09 BIOMASS FUELS↗

Corrigendum: The survivor strain: Isolation and characterization of Phormidium yuhuli AB48, a filamentous phototactic cyanobacterium with biotechnological potential

In the published article, there was an error. The introduction to this manuscript includes a typographical error which misstates the maximum salinity and pH previously observed in related cyanobacterial species. This error does not impact any analyses or conclusions reached in this manuscript.

59 BASIC BIOLOGICAL SCIENCES↗