Search NASA⌕ Search

SEARCH · Search NASA

Results for “Stress analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Stress analysis of advanced attack helicopter composite main rotor blade root end lug

Stress analysis of the Advanced Attack Helicopter (AAH) composite main rotor blade root end lug is described. The stress concentration factor determined from a finite element analysis is compared to an empirical value used in the lug design. The analysis and test data indicate that the stress concentration is primarily a function of configuration and independent of the range of material properties typical of Kevlar-49/epoxy and glass epoxy.

Baker, D. J.↗
NASA NTRS1984

Thermal-stress analysis for a wood composite blade

A thermal-stress analysis of a wind turbine blade made of wood composite material is reported. First, the governing partial differential equation on heat conduction is derived, then, a finite element procedure using variational approach is developed for the solution of the governing equation. Thus, the temperature distribution throughout the blade is determined. Next, based on the temperature distribution, a finite element procedure using potential energy approach is applied to determine the thermal-stress distribution. A set of results is obtained through the use of a computer, which is considered to be satisfactory. All computer programs are contained in the report.

Fu, K. C.↗
NASA NTRS2018

Coupled Radiative Thermal and Nonlinear Stress Analysis for Thermal Deformation in Large Space Structures

Large space structures are capable of large thermal deformations in the space environment. A case of large-scale thermal deformation was observed in the analysis of the Near Earth Asteroid Scout solar sail, with predicted tip displacements of more than one meter in seven-meter booms. Experimental data supports the broad conclusions of the analysis, but shows poor agreement on the details of the thermal deformation. Prediction that is precise enough to drive engineering decisions will require coupled thermal-stress analysis with features that are not found in current multiphysics codes. This paper describes a simple method for stepwise coupling between commercial nonlinear stress analysis software and radiative thermal analysis software. Results are presented for a round stainless steel tube, which is a common case in existing literature.

Stohlman, Olive R.↗
NASA NTRS1985

Stress analysis of 27% scale model of AH-64 main rotor hub

Stress analysis of an AH-64 27% scale model rotor hub was performed. Component loads and stresses were calculated based upon blade root loads and motions. The static and fatigue analysis indicates positive margins of safety in all components checked. Using the format developed here, the hub can be stress checked for future application.

Hodges, R. V.↗
NASA NTRS1988

Stress analysis and life prediction of gas turbine blade

A stress analysis procedure is presented for a redesign of the Space Shuttle Main Engine high pressure fuel turbopump turbine blades. The analysis consists of the one-dimensional scoping analysis to support the design layout and the follow-on three-dimensional finite element analysis to confirm the blade design at operating loading conditions. Blade life is evaluated based on high-cycle fatigue and low-cycle fatigue.

Hsiung, H. C.↗
NASA NTRS1999

Stress Analysis and Permeability Testing of Cryogenic Composite Feed Line

For the next generation Single-Stage-To-Orbit (SSTO) Reusable Launch Vehicle (RLV), the use of advanced composite materials is highly desirable and critical to the success of the mission. NASA Marshall Space Flight Center (MSFC) has been working with the aerospace industry for many years to develop and demonstrate the cryogenic composite propellant tanks and feed lines technologies. A 50.8-mm diameter composite feed line for the Clipper Graham (DCY.A) was developed and tested. The purpose of the program is to demonstrate the LH2 permeability, composite to composite and metal joints, as well as composite flange interface of the composite feed line. Stress analysis and permeability testing have been performed on this article. Recently, a larger composite feed line design is being investigated and developed at MSFC for potential use in future RLV. The diameter of the feed line is 203 mm and the overall length is approximately 2.2 meters. This one piece unlined feed line consists of three straight tubular sections joined by two 90 degree elbows. The material chosen is IM7/977-3 prepreg fabric. The lay-up pattern is [0/90, plus or minus 45]s and is built up to 18 plies to the flanges at both ends. A preliminary stress analysis has been conducted to identify potential critical stresses and to develop the finite element analysis (FEA) capability of composite feed lines. As expected, the critical stresses occurred at the rims of some flange holes and the onset of the tapered tubular sections. Further analysis is required to determine the loads, flange deflection, vibration, and combined maximum loads. Two permeability-testing apparatuses were also designed for both flat panel specimens and curved feed line sections after impact damage. A larger permeant gas exposed area is required to accurately determine the effect of impact damage on the permeability of the feed line materials. The flat panel tester was fabricated and assembled. Three test coupons were made of graphite/epoxy plain weave prepreg and unidirectional prepreg. The flow rate was calculated by measuring the change of manometer fluid height per unit time. The permeability of the coupons is then calculated according to Darcy's Law. The pressure increase due to the head rise in the manometer was not considered for the initial estimation. The result of the unidirectional composite coupon agreed with that obtained from the DC-XA feed line testing of a similar material. Further improvement on the design may be required to improve the accuracy and efficiency of permeability testing.

Chu, Tsuchin Philip↗
NASA NTRS1983

A new strategy for stress analysis using the finite element method

In the paper the authors examine the effectiveness of the Powell-Toint strategy for evaluating the Hessian of the potential energy surface of a finite element model that can be used for linear stress analysis and transient response predictions of structures. Cases for which the Powell-Toint strategy may be cost-effective with the conventional method of stress analysis are identified.

Kamat, M. P.↗
NASA NTRS1952

Investigations of Air-cooled Turbine Rotors for Turbojet Engines II : Mechanical Design, Stress Analysis, and Burst Test of Modified J33 Split-disk Rotor / Richard H. Kemp and Merland L. Moseson

A full-scale J33 air-cooled split turbine rotor was designed and spin-pit tested to destruction. Stress analysis and spin-pit results indicated that the rotor in a J33 turbojet engine, however, showed that the rear disk of the rotor operated at temperatures substantially higher than the forward disk. An extension of the stress analysis to include the temperature difference between the two disks indicated that engine modifications are required to permit operation of the two disks at more nearly the same temperature level.

TURBINES - WHEELS, DISK - STRENGTH↗
NASA NTRS1993

Contact stress analysis of spiral bevel gears using nonlinear finite element static analysis

A procedure is presented for performing three-dimensional stress analysis of spiral bevel gears in mesh using the finite element method. The procedure involves generating a finite element model by solving equations that identify tooth surface coordinates. Coordinate transformations are used to orientate the gear and pinion for gear meshing. Contact boundary conditions are simulated with gap elements. A solution technique for correct orientation of the gap elements is given. Example models and results are presented.

Bibel, G. D.↗
NASA NTRS1993

Contact stress analysis of spiral bevel gears using nonlinear finite element static analysis

A procedure is presented for performing three-dimensional stress analysis of spiral bevel gears in mesh using the finite element method. The procedure involves generating a finite element model by solving equations that identify tooth surface coordinates. Coordinate transformations are used to orientate the gear and pinion for gear meshing. Contact boundary conditions are simulated with gap elements. A solution technique for correct orientation of the gap elements is given. Example models and results are presented.

Bibel, G. D.↗
NASA NTRS1995

Contact Stress Analysis of Spiral Bevel Gears Using Finite Element Analysis

A procedure is presented for performing three-dimensional stress analysis of spiral bevel gears in mesh using the finite element method. The procedure involves generating a finite element model by solving equations that identify tooth surface coordinates. Coordinate transformations are used to orientate the gear and pinion for gear meshing. Contact boundary conditions are simulated with gap elements. A solution technique for correct orientation of the gap elements is given. Example models and results are presented.

Bibel, G. D.↗
NASA NTRS1989

Structural zooming research and development of an interactive computer graphical interface for stress analysis of cracks

Engineering problems sometimes involve the numerical solution of boundary value problems over domains containing geometric feature with widely varying scales. Often, a detailed solution is required at one or more of these features. Small details in large structures may have profound effects upon global performance. Conversely, large-scale conditions may effect local performance. Many man-hours and CPU-hours are currently spent in modeling such problems. With the structural zooming technique, it is now possible to design an integrated program which allows the analyst to interactively focus upon a small region of interest, to modify the local geometry, and then to obtain highly accurate responses in that region which reflect both the properties of the overall structure and the local detail. A boundary integral equation analysis program, called BOAST, was recently developed for the stress analysis of cracks. This program can accurately analyze two-dimensional linear elastic fracture mechanics problems with far less computational effort than existing finite element codes. An interactive computer graphical interface to BOAST was written. The graphical interface would have several requirements: it would be menu-driven, with mouse input; all aspects of input would be entered graphically; the results of a BOAST analysis would be displayed pictorially but also the user would be able to probe interactively to get numerical values of displacement and stress at desired locations within the analysis domain; the entire procedure would be integrated into a single, easy to use package; and it would be written using calls to the graphic package called HOOPS. The program is nearing completion. All of the preprocessing features are working satisfactorily and were debugged. The postprocessing features are under development, and rudimentary postprocessing should be available by the end of the summer. The program was developed and run on a VAX workstation, and must be ported to the SUN workstation. This activity is currently underway.

Gerstle, Walter↗