Search NASA⌕ Search

SEARCH · Search NASA

Results for “Swept”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Transonic transport wings - Oblique or swept

Oblique-wing twin- and single-fuselage transonic transport models were wind tunnel tested and showed superior aerodynamic efficiency to that of fixed-swept-wing, variable-sweep-wing, and delta-wing configurations similarly tested. The oblique-wing airplane had the smallest gross weight and lowest fuel consumption; it could achieve lower noise levels than swept- and delta-wing aircraft by engine-nacelle treatment; and it was aeroelastically less stable than a sweptback wing but more stable than a swept-forward wing. Graphite-epoxy met stability requirements without additional stiffening, whereas aluminum needed some additional stiffness. Further studies are called for to develop the full potential of the oblique-wing concept.

Jones, R. T.↗
NASA NTRS1979

Study of the feasibility aspects of flight testing an aeroelastically tailored forward swept research wing on a BQM-34F drone vehicle

The aspects of flight testing an aeroelastically tailored forward swept research wing on a BQM-34F drone vehicle are examined. The geometry of a forward swept wing, which is incorporated into the BQM-34F to maintain satisfactory flight performance, stability, and control is defined. A preliminary design of the aeroelastically tailored forward swept wing is presented.

Mourey, D. J.↗
NASA NTRS1980

Transonic swept-wing analysis using asymptotic and other numerical methods

The paper presents asymptotic methods for high-aspect-ratio wings in transonic flow developed for straight unyawed wings and for oblique wings. They show that the three-dimensional mixed-flow calculations may be reduced to solving a set of two-dimensional problems at each span station; the development of this theory and the related computational studies are reviewed. Differences between the piloted (oblique) wing, the swept-back wing, and the swept-forward-wing in the induced upwash are discussed; examples of similarity solutions are demonstrated for high subcritical and slightly supercritical component flows, and comparisons made with relaxation solutions of a full potential equation. The examples include oblique and symmetric swept wings, and the adequacy of the existing full-potential computer code is examined.

Cheng, H. K.↗
NASA NTRS1954

Effect of Ice Formations on Section Drag of Swept NACA 63A-009 Airfoil with Partial-Span Leading-Edge Slat for Various Modes of Thermal Ice Protection

The effects of primary and runback ice formations on the section drag of a 36 deg swept NACA 63A-009 airfoil section with a partial-span leading-edge slat were studied over a range of angles of attack from 2 to 8 deg and airspeeds up to 260 miles per hour for icing conditions with liquid-water contents ranging from 0.39 to 1.23 grams per cubic meter and datum air temperatures from 10 to 25 F. The results with slat retracted showed that glaze-ice formations caused large and rapid increases in section drag coefficient and that the rate of change in section drag coefficient for the swept 63A-009 airfoil was about 2-1 times that for an unswept 651-212 airfoil. Removal of the primary ice formations by cyclic de-icing caused the drag to return almost to the bare-airfoil drag value. A comprehensive study of the slat icing and de-icing characteristics was prevented by limitations of the heating system and wake interference caused by the slat tracks and hot-gas supply duct to the slat. In general, the studies showed that icing on a thin swept airfoil will result in more detrimental aerodynamic characteristics than on a thick unswept airfoil.

VonGlahn, Uwe H.↗
NASA NTRS1982

Evaluation of wind tunnel performance testings of an advanced 45 deg swept 8-bladed propeller at Mach numbers from 0.45 to 0.85

The increased emphasis of fuel conservation in the world and the rapid increase in the cost of jet fuel has stimulated a series of studies of both conventional and unconventional propulsion systems for commercial aircraft. The results of these studies indicate that a fuel saving of 15 to 30 percent may be realized by the use of an advanced high-speed turboprop (Prop-Fan) compared to aircraft equipped with high bypass turbofan engines of equivalent technology. The Prop-Fan propulsion system is being investigated as part of the NASA Aircraft Energy Efficient Program. This effort includes the wind tunnel testing of a series of 8 and 10-blade Prop-Fan models incorporate swept blades. Test results indicate efficiency levels near the goal of 80 percent at Mach 0.8 cruise and an altitude of 10.67 km (35,000 ft). Each successive swept model has shown improved efficiency relative to the straight blade model. The fourth model, with 45 deg swept blades reported herein, shows a net efficiency of 78.2 at the design point with a power loading of 301 kW/sq meter and a tip speed of 243.8 m/sec (800 ft/sec.).

Rohrbach, C.↗
NASA NTRS1983

High angle-of-attack flight dynamics of a forward-swept wing fighter configuration

As part of a forward-swept wing technology development effort, the Defense Advanced Research Projects Agency (DARPA), and the NASA Langley Research Center are conducting a cooperative research program to investigate the high angle-of-attack, stall and spin characteristics associated with the forward-swept wing concept. The studies are centered around the X-29A configuration which is being built to flight demonstrate the application of forward-swept wing technology to a fighter class airplane. The program includes static and dynamic wind-tunnel force tests, free-flight model tests, drop-model tests, spin-tunnel tests, and piloted simulation studies. Selected results are presented from the Langley research program on the X-29A configuration with emphasis on the high-alpha aerodynamics and the vehicle component contributions to these characteristics. The effects of these aerodynamic characteristics on the overall high-alpha flying qualities of the configuration are discussed in terms of results of the wind-tunnel free-flight tests and the piloted simulation study.

Murri, D. G.↗
NASA NTRS1985

Comparison of advanced turboprop installation on swept and unswept supercritical wings at transonic speeds

A series of wind-tunnel investigations were conducted to determine the aerodynamic interference associated with the over wing and under wing installation of a turboprop nacelle on 20 deg swept and unswept supercritical wings. The purpose of the investigations was to increase the understanding of the flow interactions involved with the nacelle turboprop integration and to obtain experimental data for the verification of computational prediction techniques. The models were tested in the Langley 16-Foot Transonic Tunnel at Mach numbers from 0.50 to 0.80 and at angles-of-attack from 0 to 5 deg. In addition, data at several propeller pitch angles and advance ratio settings were obtained. This paper which presents only the results of the over-the-wing nacelle installations shows that wing sweep had considerable influence on the installation interference. Large scale flow separation was observed on the swept wing at M = 0.8. Less severe effects were observed at M = 0.7 on the swept wing and for both M = 0.7 and 0.8 on the unswept wing.

Carlson, J. R.↗
NASA NTRS1986

Drag-reduction characteristics of aft-swept wing tips

Results are presented of a study conducted to analyze the potential aerodynamic improvements which can be obtained with aft-swept wing tips at subsonic speeds. A review and summary of previous swept-tip applications and studies are given. Additionally, the through evolution optimized tail-fin shapes of fast-cruising aquatic animals are examined as well as the wing planform shapes of sea birds. These superior long-distance travellers both display lifting-surface planform shapes with increased leading-edge sweep towards the tip. These observations and analytical results obtained with a nonlinear surface-panel method demonstrate that substantial induced-drag improvements can be obtained through the adoption of planform shapes with highly-tapered aft-swept tips.

Van Dam, C. P.↗
NASA NTRS1990

Exploratory wind tunnel investigation of the stability and control characteristics of a three-surface, forward-swept wing advanced turboprop model

The purpose of the present investigation was to parametrically study the stability and control characteristics of a forward-swept wing three-surface turboprop model through an extended angle of attack range, including the deep-stall region. As part of a joint research program between North Carolina State University and NASA Langley Research Center, a low-speed wind tunnel investigation was conducted with a three-surface, forward-swept wing, aft-mounted, twin-pusher propeller, model, representative of an advanced turboprop configuration. The tests were conducted in the NASA Langley 12-Foot Low-Speed Wind Tunnel. The model parameters varied in the test were horizontal tail location, canard size, sweep and location, and wing position. The model was equipped with air turbines, housed within the nacelles and driven by compressed air, to model turboprop power effects. A three-surface, forward-swept wing configuration that provided satisfactory static longitudinal and lateral/directional stability was identified. The three-surface configuration was found to have greater longitudinal control and increased center of gravity range relative to a conventional (two-surface) design. The test showed that power had a large favorable effect on stability and control about all three axis in the post-stall regime.

Coe, Paul L., Jr.↗
NASA NTRS1993

Takeoff/approach noise for a model counterrotation propeller with a forward-swept upstream rotor

A scale model of a counterrotating propeller with forward-swept blades in the forward rotor and aft-swept blades in the aft rotor (designated F39/A31) has been tested in the NASA Lewis 9- by 15-Foot Anechoic Wind Tunnel. This paper presents aeroacoustic results at a takeoff/approach condition of Mach 0.20. Laser Doppler Velocimeter results taken in a plane between the two rotors are also included to quantify the interaction flow field. The intention of the forward-swept design is to reduce the magnitude of the forward rotor tip vortex and/or wakes which impinge on the aft rotor, thus lowering the interaction tone levels.

Woodward, Richard P.↗
NASA NTRS1993

Numerical study of the performance of swept, curved compression surface scramjet inlets

The paper describes a computational performance-enhancement study in which systematic modifications were applied to a planar-sidewall compression scramjet inlet operating at an entrance Mach number of 4 and at a dynamic pressure of 2040 lbs/sq ft, and the performance of the modified inlet was compared to that of the original geometry by evaluating numerical flowfield solutions. The planar-sidewall compression angle was modified as a function of height using sidewall curvature and simultaneously employing both forward-swept and reverse-swept compression surfaces. The results of calculations illustrate the feasibility of obtaining enhanced performance via contour modifications of a baseline swept-sidewall compression scramjet inlet operating at an entrance Mach number of 4.

Korte, John J.↗
NASA NTRS1993

Laser velocimeter measurements of the flow field generated by a forward-swept propfan during flutter

Results are presented from an investigation to measure the flow field generated by a forward-swept propfan operating in flutter at a low forward velocity. For comparison to the flutter condition, flow field data are also presented for a slightly reduced rotational speed just below flutter. The forward-swept propfan was tested as the front rotor of a counterrotating pusher propeller. A laser Doppler velocimeter (LDV) was used to measure the velocity field in planes normal to the model centerline downstream of the rotor and in planes of constant radius within the blade passages at each operating condition. The mean time-averaged flow about the blades did not change drastically as the propfan rotational speed was increased from the stable operating point to the flutter condition. No regions of flow separation could be identified in the data plots of the mean intrablade flow field. The relative flow about the blades remained subsonic during flutter operation. The blades were found to have a higher than expected tip loading at both operating conditions. This is thought to have been caused by the outer blade sections twisting under load to higher than expected effective blade angles. This high tip loading resulted in strong vortices and a very nonuniform flow downstream of the tips of the forward-swept blades. This high tip loading may also have caused the blade flutter.

Podboy, Gary G.↗
NASA NTRS1950

A Description of the Design of Highly Swept Propeller Blades

A description of the two swept propellers investigated in the Langley 8-foot high-speed tunnel is presented, together with the discussions of the numerous assumptions and analyses on which the designs of these propellers are based. The blades are swept considerably along the entire blade radius and, in order to allow for reductions in the maximum stresses, are swept forward inboard and backward outboard. The blades have been designed on the basis of the blade-element method primarily to have subcritical efficiencies at the highest possible forward speed. The designs have been controlled primarily by the stresses in the blades. (author)

Whitcomb, Richard T↗
NASA NTRS1950

The longitudinal stability of elastic swept wings at supersonic speed

The longitudinal stability characteristics of elastic swept wings of high aspect ratio experiencing bending and torsional deformations are calculated for supersonic speed by the application of linearized lifting-surface theory. A parabolic wing deflection curve is assumed and the analysis is simplified by a number of structural approximations. The method is thereby limited in application to wings of high aspect ratio for which the root effects are small. Expressions for the lift, pitching-moment, and span load distribution characteristics are derived in terms of the elastic properties of the wing; namely, the design stress, the modulus of elasticity, the shearing modulus, and the maximum design load factor. The analysis applies to wings with leading edges swept behind the Mach lines. In all cases, however, the trailing edge is sonic or supersonic. Application of the method of analysis to wings with leading edges swept ahead of the Mach lines is discussed.

Frick, C W↗
NASA NTRS1957

Theoretical and Experimental Investigation of the Subsonic-Flow Fields Beneath Swept and Unswept Wings with Tables or Vortex-induced Velocities

The flow-field characteristics beneath swept and unswept wings as determined by potential-flow theory are compared with the experimentally determined flow fields beneath swept and unswept wing-fuselage combinations. The potential-flow theory utilized considered both spanwise and chordwise distributions of vorticity as well as the wing-thickness effects. The perturbation velocities induced by a unit horseshoe vortex are included in tabular form. The theoretical predictions of the flow-field characteristics were qualitatively correct in all cases considered, although there were indications that the magnitudes of the downwash angles tended to be overpredicted as the tip of the swept wing was approached and that the sidewash angles ahead of the unswept wing were underpredicted. The calculated effects of compressibility indicated that significant increases in the chordwise variation of flow angles and dynamic-pressure ratios should be expected in going from low to high subsonic speeds.

Alford, William J , Jr↗
NASA NTRS1993

Laser velocimeter measurements of the flow field generated by a forward-swept propfan during flutter

Results are presented from an investigation to measure the flow field generated by a forward-swept propfan operating in flutter at a low forward velocity. For comparison to the flutter condition, flow field data are also presented for a slightly reduced rotational speed just below flutter. The forward-swept propfan was tested as the front rotor of a counterrotating pusher propeller. A laser Doppler velocimeter (LDV) was used to measure the velocity field in planes normal to the model centerline downstream of the rotor and in planes of constant radius within the blade passages at each operating condition. A comparison of the data taken at the two different operating conditions indicated that the mean, time-averaged flow about the blades did not change drastically as the propfan rotational speed was increased from the stable operating point to the flutter condition. No regions of flow separation could be identified in the data plots of the mean intrablade flow field. The data also indicate that the relative flow about the blades remained subsonic during flutter operation. The blades were found to have a higher than expected tip loading at both operating conditions. This is thought to have been caused by the outer blade sections twisting under load to higher than expected effective blade angles. This high tip loading resulted in strong vortices and a very nonuniform flow downstream of the tips of the forward-swept blades. This high tip loading may also have caused the blade flutter.

Podboy, Gary G.↗
NASA NTRS1992

Aeroelastic modeling of composite rotor blades with straight and swept tips

This paper presents an analytical study of the aeroelastic behavior of composite rotor blades with straight and swept tips. The blade is modeled by beam type finite elements. A single finite element is used to model the swept tip. The nonlinear equations of motion for the FEM are derived using Hamilton's principle and based on a moderate deflection theory and accounts for: arbitrary cross-sectional shape, pretwist, generally anisotropic material behavior, transverse shears and out-of-plane warping. Numerical results illustrating the effects of tip sweep, anhedral and composite ply orientation on blade aeroelastic behavior are presented. It is shown that composite ply orientation has a substantial effect on blade stability. At low thrust conditions, certain ply orientations can cause instability in the lag mode. The flap-torsion coupling associated with tip sweep can also induce aeroelastic instability in the blade. This instability can be removed by appropriate ply orientation in the composite construction. These results illustrate the inherent potential for aeroelastic tailoring present in composite rotor blades with swept tips, which still remains to be exploited in the design process.

Yuan, Kuo-An↗
NASA NTRS1994

A spectrally accurate boundary-layer code for infinite swept wings

This report documents the development, validation, and application of a spectrally accurate boundary-layer code, WINGBL2, which has been designed specifically for use in stability analyses of swept-wing configurations. Currently, we consider only the quasi-three-dimensional case of an infinitely long wing of constant cross section. The effects of streamwise curvature, streamwise pressure gradient, and wall suction and/or blowing are taken into account in the governing equations and boundary conditions. The boundary-layer equations are formulated both for the attachment-line flow and for the evolving boundary layer. The boundary-layer equations are solved by marching in the direction perpendicular to the leading edge, for which high-order (up to fifth) backward differencing techniques are used. In the wall-normal direction, a spectral collocation method, based upon Chebyshev polynomial approximations, is exploited. The accuracy, efficiency, and user-friendliness of WINGBL2 make it well suited for applications to linear stability theory, parabolized stability equation methodology, direct numerical simulation, and large-eddy simulation. The method is validated against existing schemes for three test cases, including incompressible swept Hiemenz flow and Mach 2.4 flow over an airfoil swept at 70 deg to the free stream.

Pruett, C. David↗