Search NASA⌕ Search

SEARCH · Search NASA

Results for “TAIL SURFACES, HORIZONTAL - CHAR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1937

Full-scale Wind-tunnel and Flight Tests of a Fairchild 22 Airplane Equipped with External-airfoil Flaps

Wind-tunnel and flight tests have been made of a Fairchild 22 airplane equipped with a wing having external-airfoil flaps that also perform the function of ailerons. Lift, drag, and pitching-moment coefficients of the airplane with several flap settings, and the rolling- and yawing-moment coefficients with the flaps deflected as ailerons were measured in the full-scale tunnel with the horizontal tail surfaces and propeller removed. The effect of the flaps on the low speed and on the take-off and landing characteristics, the effectiveness of flaps when used as ailerons, and the forces required to operate them as ailerons were determined in flight. The wind-tunnel tests showed that the flaps increased the maximum lift coefficient of the airplane from 1.51 with the flap in the minimum drag position to 2.12 with the flap in the minimum drag position to 2.12 with the flap deflected 30 degrees. In the flight tests the minimum speed decreased from 46.8 miles per hour with the flaps up to 41.3 miles per hour with the flaps deflected. The required take-off run to attain a height of 50 feet was reduced from 820 to 750 feet and the landing run from a height of 50 feet was reduced from 930 to 480 feet. The flaps for this installation gave lateral control that was not entirely satisfactory. Their rolling action was good but the adverse yaw resulting from their use was greater than is considerable, and the stick forces required to operate them increased too rapidly with speed.

Reed, Warren D↗
NASA NTRS1938

Flight and Wind-tunnel Tests of an XBM-1 Dive Bomber

Results are given of pressure-distribution measurements made in flight over the right wing cellule and the right half of the horizontal tail surfaces of a dive-bombing biplane. Simultaneous measurements were also taken of the air speed, control-surface positions, control forces, and normal accelerations during various abrupt maneuvers in vertical plane. These maneuvers consisted of push-downs and pull-ups from level flight, dives and dive pull-ups from inverted flight. Besides the pressure measurements, flight tests were made to obtain (1) wing-fabric deflections during dives and (2) variation of the minimum drag coefficient with Reynolds Number. Supplementary tests were also done in the full-scale wind tunnel to obtain the characteristics of the airplane under various propeller conditions and with various tail settings. The results indicate that: (1) by increasing the fabric deflection between pressure ribs, the span load distribution was considerably modified near the center and the wing moment relations were changed; and (2) the minimum drag was less for the idling propeller than for the propeller locked in a vertical position. The value of C(sub D sub min) was equal to K(Reynolds Number)(exp -0.03) for a range from 2,800,000 to 13,100,000.

Donely, Philip↗
NASA NTRS1940

Transient Effects of the Wing Wake on the Horizontal Tail

An investigation was made of the effect of the wing wake on the lift of the horizontal tail surfaces. In the development of expressions for this effect, the growth of wing circulation and wing wake, the time interval represented by the tail length, and the development of lift by the rail were considered. The theory has been applied to a specific case to show the magnitude of the effect to be expected. It is shown that, for motions below a certain frequency, the development of lift by the tail may be represented by a simple lag function. The lag is, however, somewhat greater than that indicated by the rail length.

Jones, Robert T↗
NASA NTRS1926

Slip stream effect

The horizontal tail surfaces of a new airplane usually are proportional so that the curve of moment about the center of gravity, combined with a similar curve for the wings alone, gives a composite curve which provides a certain specified degree of static stability. With the application of power three additional factors must be considered in calculations: the moment of the propeller thrust; the change in the velocity of the air over the tail due to the slipstream; and the change in direction of the air over the tail due to the slipstream. The last two factors are considered in this report.

STABILITY↗
NASA NTRS1928

Pressure Distribution over a Wing and Tail Rib of a VE-7 and of a TS Airplane in Flight

This investigation was made to determine the pressure distribution over a rib of the wing and over a rib of the horizontal tail surface of an airplane in flight and to obtain information as to the time correlation of the loads occurring on these ribs. Two airplanes, VE-7 and TS, were selected in order to obtain the information for a thin and a thick wing section. In each case the pressure distribution was recorded for the full range of angle of attack in level flight and throughout violent maneuvers. The results show: (a) that the present rib load specifications in use by the Army Air Corps and the Bureau of Aeronautics, Navy Department, are in fair agreement with the loads actually occurring in flight, but could be slightly improved; (b) that there appears to be no definite sequence in which wing and tail surface ribs reach their respective maximum loads in different maneuvers; (c) that in accelerated flight, at air speeds less than or equal to 60 per cent of the maximum speed, the accelerations measured agree very closely with the theoretically possible maximum accelerations. In maneuvers at higher air speeds the observed accelerations were smaller than those theoretically possible. (author)

Crowley, J W , Jr↗
NASA NTRS1937

Pressure-Distribution Measurements on O-2H Airplane in Flight

Results are given of pressure-distribution measurements made over two different horizontal tail surfaces and the right wing cellule, including the slipstream area, of an observation-type biplane. Measurements were also taken of air speed, control-surface positions, control-stick forces, angular velocities, and accelerations during various abrupt maneuvers. These maneuvers consisted of push-downs and pull-ups from level flight, dive pull-outs, and aileron rolls with various thrust conditions. The results from the pressure-distribution measurements over the wing cellule are given on charts showing the variation of individual rib coefficients with wing coefficients; the data from the tail-surface pressure-distribution measurements are given mainly as total loads and moments. These data are supplemented by time histories of the measured quantities and isometric views of the rib pressure distributions occurring in abrupt maneuvers.

Pearson, H A↗
NASA NTRS1937

Pressure-Distribution Measurements at Large Angles of Pitch on Fins of Different Span-Chord Ratio on a 1/40-Scale Model of the U. S. Airship "Akron."

Report presents the results of pressure-distribution measurements on a 1/40-scale model of the U. S. Airship "Akron" conducted in the NACA 20-foot wind tunnel. The measurements were made on the starboard fin of each of four sets of horizontal tail surfaces, all of approximately the same area but differing in span-chord ratio, for five angles of pitch varying from 11.6 degrees to 34 degrees, for four elevator angles, and at air speeds ranging from 56 to 77 miles per hour. Pressures were also measured at 13 stations along the rear half of the port side of the hull at one elevator setting for the same five angles of pitch and at an air speed of approximately 91 miles per hour. The normal force on the fin and the moment of forces about the fin root were determined. The results indicate that, ignoring the effect on drag, it would be advantageous from structural considerations to use a fin of lower span-chord ratio than that used on the "Akron."

Mchugh, James G↗
NASA NTRS1940

Longitudinal stability and control with special reference to slipstream effects

Report presents the results of a study of data obtained in the NACA full-scale wind tunnel concerning the effects of interference and of propeller operation on longitudinal stability and control. The data include pitching moments for various power conditions for airplanes with tails removed and with tails set at various stabilizer and elevator angles. A number of surveys of the dynamic pressure and the flow direction in the region of the horizontal tail surface are also included. Results are given for eight airplanes, including a model of a four-engine airplane tested both as a tractor and as a pushed and a model of two-engine pusher. The effects are shown of propeller operation on the downwash angles and the dynamic pressures at the tail and on the pitching-moment contribution of the propeller and the wing.

Katzoff, S↗
NASA NTRS1954

Experimental investigation of the forces and moments due to sideslip of a series of triangular vertical and horizontal tail combinations at Mach numbers

An experimental investigation was made at Mach numbers of 1.62, 1.93, and 2.41 of a series of tail combinations consisting of triangular vertical tail attached symmetrically to a triangular horizontal tail to determine the lateral force, yawing moment, and rolling moment due to sideslip. The apex angles of both the vertical- and horizontal-tail surfaces were varied systematically in order to obtain results for an appreciable range of operating conditions. The results of the investigation indicated that, for tails having subsonic leading edges and supersonic trailing edges, the lateral-force derivative and the yawing-moment derivative were predicted satisfactorily by the method presented in NACA TN 3071 except when the leading edges approach a sonic condition. The theoretical rolling-moment derivative was in fair agreement with the experimental derivative. For the limited tests in which both the leading and trailing edges were supersonic, the prediction of the lateral-force derivative and the yawing-moment derivative obtained from NACA TN 2412 was in good agreement with the experimental derivatives, whereas the prediction of the rolling-moment derivative was fair.

Coletti, Donald E↗
NASA NTRS1946

Free-spinning-tunnel Tests of a 1/26th Scale Model of the Douglas XTB2D-1 Airplane

A spin-tunnel investigation of a 1/26 scale model of the Douglas XTB2D-1 airplane has been conducted in the Langley 20-foot free-spinning tunnel. The effects of control settings and movements upon the erect- and inverted-spin and recovery characteristics of the model were determined for various loading conditions. Tests were also performed to determine the effects of various tail modifications. The investigation included emergency spin-recovery parachute tests as well as crew-escape and rudder- and elevator-force tests. All tests were performed at an equivalent spin altitute of 20,000 feet. The recovery characteristics of the model in the original design were found to be unsatisfactory. Installation of a large ventral fin, installation of tip fins on the horizontal tail, or installation of a small ventral fin in combination with antispan fillets and a spanwise extension of the horizontal-tail surfaces satisfactorily improved the recovery characteristics of the model.

Stone, Ralph W↗
NASA NTRS1934

Effect of fuselage and engine nacelles on some aerodynamic properties of an airplane wing

With the aid of the method of J. Lotz, the writer undertook to solve theoretically the lift distribution along the span of an airplane wing, when the outline of the wing is uneven. This problem arises in the case of a mid-wing monoplane with embedded engine nacelles. The fuselage and the nacelles were considered as aerodynamically profiled, that is, as lift-producing parts. The task was therefore to determine not only the disturbance caused by the fuselage and nacelles, but also their share in the total lift of the wing. After the above-mentioned calculations, the induced velocity, due to the vortex system by which the wing was replaced, was also calculated and measured at the points corresponding, in an airplane, to the location of the horizontal tail surfaces.

Vladea, Joan↗
NASA NTRS1995

Predictions Of Accretion Of Ice On A Commercial Airplane

Report presents computational study of accretion of ice on wings and on horizontal tail surfaces of simplified version of Boeing 737 airplane. Calculations performed by use of LEWICE3D computer code, which incorporates panel-method mathematical model of three-dimensional potential flow and mathematical models of trajectories of drops of water entrained in flow, impingement of drops on surfaces, and transfer of heat.

Bidwell, C. S.↗
NASA NTRS2014

A Summary of Revisions Applied to a Turbulence Response Analysis Method for Flexible Aircraft Configurations

A software program and associated methodology to study gust loading on aircraft exists for a classification of geometrically simplified flexible configurations. This program consists of a simple aircraft response model with two rigid and three flexible symmetric degrees-of - freedom and allows for the calculation of various airplane responses due to a discrete one-minus- cosine gust as well as continuous turbulence. Simplifications, assumptions, and opportunities for potential improvements pertaining to the existing software program are first identified, then a revised version of the original software tool is developed with improved methodology to include more complex geometries, additional excitation cases, and additional output data so as to provide a more useful and precise tool for gust load analysis. In order to improve the original software program to enhance usefulness, a wing control surface and horizontal tail control surface is added, an extended application of the discrete one-minus-cosine gust input is employed, a supplemental continuous turbulence spectrum is implemented, and a capability to animate the total vehicle deformation response to gust inputs is included. These revisions and enhancements are implemented and an analysis of the results is used to validate the modifications.

Funk, Christie J.↗
NASA NTRS2022

X-59 Sonic Boom Test Results from the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

A wind tunnel test was conducted to investigate near-field sonic boom pressure signatures from a model of the X-59 Low-Boom Flight Demonstrator aircraft. A 1.62%-scale model of the aircraft in the C612A configuration was fabricated for the wind tunnel test, which took place in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel in September and October 2021. The model had provisions for two different mounting options: a swept blade strut that attached at the top of model ahead of the inlet, and rear-entry sting that was made as one piece with a dummy nacelle, and which had a 2”-long cylindrical segment aft of the nozzle exit before tapering up in size. The blade strut allowed for a clean aft end of the model for evaluation of the shocks from that region, while the sting avoided the significant distortions of the flow and shocks from the blade strut along the top of the model. Both the sting and the strut had adapters that attached to a force balance. The model had alternate parts for ±0.5° deflections of the flaps, ailerons, and stabilator, and ±1° deflections of the T-tail horizontal surface. Off-body static pressure measurements of the flow field below the model were made by use of a pressure rail which had 420 orifices along its tip. The model was positioned at various heights from the rail by vertical movement of the wind tunnel strut, and at various longitudinal stations relative to the rail by means of a linear actuator mounted between the tunnel strut and the balance. The longitudinal positioning allowed multiple pressure signatures to be obtained along different portions of the rail. These signatures were aligned by accounting for the model longitudinal movement and then averaged to take out the effects of tunnel flow distortions and the interference of the rail flow field and shocks on the model pressure signatures. The test was run at approximate Mach numbers of 1.36, 1.4, and 1.47, and the model was set at various angles of attack and roll relative to the rail. Plots of the model signatures for all the variations of Mach number, model angles, control deflections, and height relative to the rail are provided throughout the report. Repeatability was generally very good and gave confidence in the quality of the measurements. The signatures measured at various heights from the rail provided insight into the aging of the model shocks as they propagated from 1.2 to 3 body lengths from the model. Off-track signatures up to 45° from centerline obtained by rolling the model gave indications of the shock flow fields across the width of the sonic boom carpet. The deflections of the various control surfaces allowed assessment of the boom sensitivity to the control surface movements.

Sonic boom↗
NASA NTRS1929

The Pressure Distribution over the Horizontal and Vertical Tail Surfaces of the F6C-4 Pursuit Airplane in Violent Maneuvers

This investigation of the pressure distribution on the tail surfaces of a pursuit airplane in violent maneuvers was conducted for the purpose of determining the maximum loads likely to be encountered on these surfaces in flight. The information is a part of that needed for a revision of existing loading specifications to bring these into closer agreement with the actual flight conditions. A standard F6C-4 airplane was used and the pressure distribution over the right horizontal and complete vertical tail surfaces was recorded throughout violent maneuvers. The results show that the existing loading specifications do not conform satisfactorily to the loadings existent in critical conditions, and in some cases were exceeded by the loads obtained. An acceleration of 10.5 G. Was recorded in one maneuver in which the pilot suffered severely; it is therefore indicated that the limits of the physical resistance of the pilot to violent maneuvers are being approached. Navy specifications for the structural design of tail surfaces are included as an appendix. (author)

Rhode, R V↗