Search NASA⌕ Search

SEARCH · Search NASA

Results for “TIP SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Design and performance of a 427-meter-per-second-tip-speed two-stage fan having a 2.40 pressure ratio

The aerodynamic design and the overall and blade-element performances are presented of a 427-meter-per-second-tip-speed two-stage fan designed with axially spaced blade rows to reduce noise transmitted upstream of the fan. At design speed the highest recorded adiabatic efficiency was 0.796 at a pressure of 2.30. Peak efficiency was not established at design speed because of a damper failure which terminated testing prematurely. The overall efficiencies, at 60 and 80 percent of design speed, peaked at approximately 0.83.

Cunnan, W. S.↗
NASA NTRS1980

Rotor redesign for a highly loaded 1800 ft/sec tip speed fan, 2

Tests were conducted on a 0.5 hub/tip ratio single-stage fan designed to produce a pressure ratio of 2.280 at an efficiency of 83.8 percent with a rotor tip speed of 548.6 m/sec (1800 ft/sec). The rotor was designed utilizing a quasi three dimensional design system and four-part, multiple-circular-arc airfoil sections. The rotor is the third in a series of single-stage fans that have included a precompression airfoil design and a multiple-circular-arc airfoil design. The stage achieved a peak efficiency of 82.8 percent after performance had deteriorated by 0.6 of a point. The design mass flow was achieved at the peak efficiency point, and the stage total pressure ratio was 2.20, which is lower than the design goal of 2.28. The surge margin of 13% from the peak efficiency point exceeded the design goal of 7%.

Bolt, C. R.↗
NASA NTRS1972

High loading, 1800 ft/sec tip speed, transonic compressor fan stage. 2: Final report

Tests were conducted on a 0.5 hub/tip ratio, single-stage fan-compressor designed to produce a pressure ratio of 2.285 an efficiency of 84 percent with a rotor tip speed of 1800 feet per second. A peak efficiency of 82 percent was achieved by the stage at a stall margin of 6.5 percent. Tests showed that stall-limit line was slightly sensitive to tip-radial distortion, but stall-line improvements were noted when the stage was subjected to circumferential and hub-radial flow distortions. Rotor blade passage and trailing edge shock positions were inferred from static pressure contours over the rotor tips.

Morris, A. L.↗
NASA NTRS1974

High-tip-speed fiber composite compressor blades: Vibration and strength analysis

An analytical procedure is described which couples composite mechanics computer codes with NASTRAN. This procedure was used to perform a detailed analysis of a high-tip-speed fiber composite compressor fan blade. The results indicate that the various vibration modes of this blade are highly coupled. Mechanical load ply stresses are well below the corresponding room temperature strengths. Lamination residual stresses are likely to cause transply cracks and interply delamination. Transply cracks and relaxation of root fixity decrease the vibrational frequencies whereas centrifugal stiffening increases them. Comparisons of results for various parameters are presented in tabular and graphical form.

Chamis, C. C.↗
NASA NTRS1974

High-tip-speed fiber composite compressor blades - Vibration and strength analyses

An analytical procedure is described which couples composite mechanics computer codes with NASTRAN. This procedure was used to perform a detailed analysis of a high-tip-speed fiber composite compressor fan blade. The results indicate that the various vibration modes of this blade are highly coupled. Mechanical load ply stresses are well below the corresponding room temperature strengths. Lamination residual stresses are likely to cause transply cracks and interply delamination. Transply cracks and relaxation of root fixity decrease the vibrational frequencies whereas centrifugal stiffening increases them. Comparisons of results for various parameters are presented in tabular and graphical form.

Chamis, C. C.↗
NASA NTRS1972

Performance of a 1380-foot-per-second-tip-speed axial-flow compressor rotor with a blade tip solidity of 1.3

Aerodynamic design parameters are presented along the overall and blade element performance, of an axial flow compressor rotor designed to study the effects of blade solidity on efficiency and stall margin. At design speed the peak efficiency was 0.844 and occurred at an equivalent weight flow of 63.5 lb/sec with a total pressure ratio of 1.801. Design efficiency, pressure ratio, and weight flow 0.814, 1.65, and 65.3(41.1 lb/sec/sq ft of annulus area), respectively. Stall margin for design speed was 6.4 percent based on the weight flow and pressure ratio values at peak efficiency and just prior to stall.

Hager, R. D.↗
NASA NTRS1973

Effect of rotor design tip speed on noise of a 1.21 pressure ratio model fan under static conditions

Preliminary results are presented for a reverberant-field noise investigation of three fan stages designed for the same overall total pressure ratio of 1.21 at different rotor tip speeds (750, 900, and 1050 ft/sec). The stages were tested statically in a 15-inch-diameter model lift fan installed in a wing pod located in the test section of a wind tunnel. Although the fan stages produced essentially the same design pressure ratio, marked differences were observed in the variation of fan noise with fan operating speed. At design speed, the forward-radiated sound power level was approximately the same for the 750 ft/sec and 900 ft/sec stages. For the 1050 ft/sec stage, the design-speed forward-radiated power level was about 7 db higher due to the generation of multiple pure tone noise.

Loeffler, I. J.↗
NASA NTRS1973

Effect of rotor design tip speed on noise of a 1.21 pressure ratio model fan under static conditions

Preliminary results are presented for a reverberant-field noise investigation of three fan stages designed for the same overall total pressure ratio of 1.21 at different rotor tip speeds (750, 900, and 1050 fps). The stages were tested statically in a 15-in.-dia model lift fan installed in a wing pod located in the test section of a wind tunnel. Although the fan stages produced essentially the same design pressure ratio, marked differences were observed in the variation of fan noise with fan operating speed. At design speed, the forward-radiated sound power level was approximately the same for the 750 and 900 fps stages. For the 1050 fps stage, the design-speed forward-radiated power level was about 7 dB higher due to the generation of multiple pure tone noise.

Loeffler, I. J.↗
NASA NTRS2018

Acoustic Testing of a High-Tip-Speed Fan with Bypass-Duct Liners

Under a pair of Space Act Agreements between NASA and Honeywell Aerospace, a model-scale (22 in.-diameter fan) acoustic wind tunnel test was carried out in the fall of 2014 in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel. The goal was to obtain acoustic pressure measurements for far-field, inlet and exit rotating rake, and in-duct microphone locations. This supersonic-tip-speed fan was tested in three bypass duct configurations: hard-wall, traditional liner, and advanced multiple-degree-of-freedom. Limited aerodynamic data was collected to verify the expected operating conditions. Preliminary analysis of the acoustic data finds it suitable for use in evaluating current NASA and Honeywell Aerospace acoustic tools and liner design practices.

Noise↗
NASA NTRS2019

Acoustic Testing of a High-Tip-Speed Fan with Bypass-Duct Liners - Overview

Under a pair of Space Act Agreements between NASA and Honeywell Aerospace, a model-scale (22 in.-diameter fan) acoustic wind tunnel test was carried out in the fall of 2014 in the NASA Glenn Research Center 9- by 15-Foot Low-Speed Wind Tunnel. The goal was to obtain acoustic pressure measurements for far-field, inlet and exit rotating rake, and in-duct microphone locations. This supersonic-tip-speed fan was tested in three bypass duct configurations: hard-wall, traditional liner, and advanced multiple-degree-of-freedom. Limited aerodynamic data was collected to verify the expected operating conditions. Preliminary analysis of the acoustic data finds it suitable for use in evaluating current NASA and Honeywell Aerospace acoustic tools and liner design practices. This report provides an overview of the test and some preliminary findings.

Miller, Christopher J.↗
NASA NTRS1981

An evaluation of a simplified near field noise model for supersonic helical tip speed propellers

Existing propeller noise models are versatile and complex but require large computational times, therefore a simplified noise model that could be used to obtain quick noise estimates for these propellers was evaluated. This simplified noise model compared favorably with a complex model for a straight blade propeller and for swept propeller blades when the propeller sweep was properly considered. The simplified model can thus be used as an approximation to the complex model. Comparisons of either the complex or simplified noise models with the available noise data are not good for supersonic propeller helical tip speeds. By adjusting various constants in the simplified model, the noise estimates can be brought into the same range as the data at the propeller design point but the variation of the model with helical tip Mach number remains different than the data.

Dittmar, J. H.↗
NASA NTRS1990

Aeroacoustic effects of reduced aft tip speed at constant thrust for a model counterrotation turboprop at takeoff conditions

A model high-speed, advanced counterrotation propeller, F7/A7, was tested in the NASA Lewis Research Center's 9- by 15-foot anechoic wind tunnel at simulated takeoff and approach conditions of Mach 0.2. The propeller was operated in a baseline configuration with the forward and aft rotor blade setting angles (36.2deg and 35.4 deg) and forward and aft rotational speeds essentially equal. Two additional configurations were tested with the aft rotor at increased blade setting angles and the rotational speed reduced to achieve overall performance similar to that of the baseline configuration. The aft rotor blade angles were adjusted such that the thrust and power absorption for each rotor remained the same as for the baseline configuration. Acoustic data were taken with an axially translating microphone probe that was attached to the tunnel floor. Concurrent aerodynamic data were taken to define propeller operating conditions. The aft rotor fundamental tone was about 6 dB lower with the 36.2 deg and 38.4 deg blade setting angles, and about 9 dB lower with the 36.2 and 41.4 deg blade setting angles. Predicted noise reductions based on tip speed considerations were 5 and 9.5 dB, respectively, for the two altered blade setting angles.

Woodward, Richard P.↗
NASA NTRS1984

A parametric study of blade vortex interaction noise for two, three, and four-bladed model rotors at moderate tip speeds Theory and experiment

An investigation of blade slap due to blade vortex interaction (BVI) has been conducted. This investigation consisted of an examination of BVI blade slap for two, three, and four-bladed model rotors at tip Mach numbers ranging from 0.20 to 0.50. Blade slap contours have been obtained for each configuration tested. Differences in blade slap contours, peak sound pressure level, and directivity for each configuration tested are noted. Additional fundamental differences, such as multiple interaction BVI, are observed and occur for only specific rotor blade configurations. The effect of increasing the Mach number on the BVI blade slap for various rotor blade combinations has been quantified. A peak blade slap Mach number scaling law is proposed. Comparison of measured BVI blade slap with theory is made.

Leighton, K. P.↗
NASA NTRS1975

Fan noise reduction at subsonic and supersonic tip speeds with high Mach number inlets

Results are presented for an experimental study of two fixed geometry inlets and one translating centerbody type inlet tested in an anechoic-chamber transonic-compressor facility. The test vehicle was a 12-inch tip diameter single-stage transonic compressor with 19 rotor blades and 30 stator blades located approximately two chord lengths downstream of the rotor. It is shown that the translating centerbody type of inlet is superior to the collapsing cowl type for noise reduction at high subsonic Mach numbers, both acoustically and aerodynamically. The feasibility of using a high inlet Mach number depends largely on the maximum area ratio requirement (normally at landing). The high inlet Mach numbers are more effective in reducing high-frequency noise than low frequencies and more effective in reducing the blade passage frequency than the overall noise level.

Lumsdaine, E.↗
NASA NTRS1956

Investigation of Turbines Suitable for Use in a Turbojet Engine with High Compressor Pressure Ratio and Low Compressor-tip Speed VI: Experimental Performance of Two-stage Turbine

The brake internal efficiency of the highly loaded two-stage turbine was 0.79 equivalent design work and speed. The maximum brake internal efficiency was 0.84. A radial survey revealed these major defects: (1) the first-rotor throat area was too large, and a large area of underturned flow existed near the tip;(2) considerable underturning existed at the second-stator outlet; and (3) tangential components of velocity at the turbine outlet amounted to 2.5 points in turbine efficiency.

Davison, Elmer H↗
NASA NTRS1984

Detailed flow measurements in casing boundary layer of 429-meter-per-second-tip-speed two-stage fan

Detailed flow measurements between all blade rows were taken in the outer 30 percent of passage height of a two stage fan. Tabulations of the detailed flow measurements are included. Results of these measurements revealed the steep axial velocity profiles near the casing. The axial velocity profile near the casing at the rotor exists was much steeper than at the stator exits. The data also show overturning of the flow at the tip at the stator exits. The effect of mixing is shown by the redistribution of the first stage rotor exit total temperature profile as it passes through the following stator.

Gorrell, W. T.↗
NASA NTRS1983

A possible explanation for the present difference between linear noise theory and experimental data for supersonic helical tip speed propellers

High speed turboprops are attractive candidates for future aircraft because of their high propulsive efficiency. However, the noise of their propellers may create a cabin environment problem for the aircraft powered by these propellers. The noise of some propeller models was measured, and predictions of the noise using a method based on the Ffowcs Williams-Hawkins equation were made. The predictions and data agree well at lower helical tip Mach numbers but deviate above Mach 1.0. Some possible reasons why the theory does not predict the data and focuses on improvement of the aerodynamic inputs as the most likely remedy are investigated. In particular, it is proposed that an increase in the drag and a decrease in the lift near the tip of the blade where the majority of the noise is generated, is warranted in the input to the theory.

Dittmar, J. H.↗