Search NASA⌕ Search

SEARCH · Search NASA

Results for “TURBOPROP ENGINE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Experimental Investigation of Water Droplet Impingement on Airfoils, Finite Wings, and an S-duct Engine Inlet

Validation of trajectory computer codes, for icing analysis, requires experimental water droplet impingement data for a wide range of aircraft geometries as well as flow and icing conditions. This report presents improved experimental and data reduction methods for obtaining water droplet impingement data and provides a comprehensive water droplet impingement database for a range of test geometries including an MS(1)-0317 airfoil, a GLC-305 airfoil, an NACA 65(sub 2)-415 airfoil, a commercial transport tail section, a 36-inch chord natural laminar flow NLF(1)-0414 airfoil, a 48-inch NLF(1)-0414 section with a 25 percent chord simple flap, a state-of-the-art three-element high lift system, a NACA 64A008 finite span swept business jet tail, a full-scale business jet horizontal tail section, a 25 percent-scale business jet empennage, and an S-duct turboprop engine inlet. The experimental results were obtained at the NASA Glenn Icing Research Tunnel (IRT) for spray clouds with median volumetric diameter (MVD) of 11, 11.5, 21, 92, and 94 microns and for a range of angles of attack. The majority of the impingement experiments were conducted at an air speed of 175 mph corresponding to a Reynolds number of approximately 1.6 million per foot. The maximum difference of repeated tests from the average ranged from 0.24 to 12 percent for most of the experimental results presented. This represents a significant improvement in test repeatability compared to previous experimental studies. The increase in test repeatability was attributed to improvements made to the experimental and data reduction methods. Computations performed with the LEWICE-2D and LEWICE-3D computer codes for all test configurations are presented in this report. For the test cases involving median volumetric diameters of 11 and 21 microns, the correlation between the analytical and experimental impingement efficiency distributions was good. For the median volumetric diameters of 92 and 94-micron cases, however, the analysis produced higher impingement efficiencies and larger impingement limits than the experiment. It is speculated that this discrepancy is due to droplet splashing and breakup experienced by large droplets during impingement.

Papadakis, Michael↗
NASA NTRS1997

Fatigue Reliability of Gas Turbine Engine Structures

The results of an investigation are described for fatigue reliability in engine structures. The description consists of two parts. Part 1 is for method development. Part 2 is a specific case study. In Part 1, the essential concepts and practical approaches to damage tolerance design in the gas turbine industry are summarized. These have evolved over the years in response to flight safety certification requirements. The effect of Non-Destructive Evaluation (NDE) methods on these methods is also reviewed. Assessment methods based on probabilistic fracture mechanics, with regard to both crack initiation and crack growth, are outlined. Limit state modeling techniques from structural reliability theory are shown to be appropriate for application to this problem, for both individual failure mode and system-level assessment. In Part 2, the results of a case study for the high pressure turbine of a turboprop engine are described. The response surface approach is used to construct a fatigue performance function. This performance function is used with the First Order Reliability Method (FORM) to determine the probability of failure and the sensitivity of the fatigue life to the engine parameters for the first stage disk rim of the two stage turbine. A hybrid combination of regression and Monte Carlo simulation is to use incorporate time dependent random variables. System reliability is used to determine the system probability of failure, and the sensitivity of the system fatigue life to the engine parameters of the high pressure turbine. 'ne variation in the primary hot gas and secondary cooling air, the uncertainty of the complex mission loading, and the scatter in the material data are considered.

Cruse, Thomas A.↗
NASA NTRS1980

The NASA high-speed turboprop program

Technology readiness for Mach 0.7 to 0.8 turboprop powered aircraft with the potential for fuel savings and DOC reductions of up to 30 and 15 percent respectively relative to current in-service aircraft is addressed. The areas of propeller aeroacoustics, propeller structures, turboprop installed performance, aircraft cabin environment, and turboprop engine and aircraft studies are emphasized. Large scale propeller characteristics and high speed propeller flight research tests using a modified testbed aircraft are also considered.

Dugan, J. F.↗
NASA NTRS1980

Application of advanced technologies to small, short-haul transport aircraft

The performance and economic benefits available by incorporation of advanced technologies into the small, short haul air transport were assessed. Low cost structure and advanced composite material, advanced turboprop engines and new propellers, advanced high lift systems and active controls; and alternate aircraft configurations with aft mounted engines were investigated. Improvements in fuel consumed and aircraft economics (acquisition cost and direct operating cost) are available by incorporating selected advanced technologies into the small, short haul aircraft.

Coussens, T. G.↗
NASA NTRS1980

The NASA high-speed turboprop program

NASA's Advanced Turboprop Project is a three-phase effort initiated in 1978 to provide technology readiness for Mach 0.7 to 0.8 turboprop-powered aircraft; with the potential for fuel savings and DOC reductions of up to 30 and 15%, respectively, relative to current in-service aircraft. This paper reviews the status of Phase I in the areas of propeller aeroacoustics, propeller structures, turboprop installed performance, aircraft cabin environment, and turboprop engine and aircraft studies. Current plans to establish large-scale propeller characteristics and to conduct high-speed propeller flight research tests using a modified testbed aircraft are also presented.

Dugan, J. F.↗
NASA NTRS1982

CO, O3, and aerosol measurements from NASA Global Tropospheric Experiment - Test flights 1981

A series of four instrument test flights was conducted during July 1981 in preparation for the NASA Global Tropospheric Experiment. The purpose of the flights was to demonstrate the feasibility and value of simultaneously measuring several specific atmospheric pollutants over a 25 deg latitudinal range. Carbon monoxide and methane grab samples were obtained simultaneously with nearly continuous in situ ozone and remote ozone and aerosol optical radar measurements. The sampling platform was a NASA Electra, a four engine turboprop aircraft. Attention is given to CO and CH4 sample collection and analysis, ozone measurement methods, the aerosol measurement method, an interpretation of the optical radar display, and a synergistic consideration of results.

Hinton, R. R.↗
NASA NTRS1983

NASA Lewis Research Center's program on icing research

NASA is again actively involved in aircraft icing research. This paper briefly describes the new research activity in ice protection systems, icing instrumentation, experimental methods, analytical modeling for the above, and in-flight research. The renewed interest in aircraft icing has come about mainly because of the new need for all-weather helicopters and general aviation aircraft. Because of increased fuel costs, tomorrow's commercial transports also will require new types of ice protection systems compatible with the more efficient high by-pass and turboprop engines. And all types of aircraft require better estimates of the aeropenalties caused by ice on unprotected surfaces.

Reinmann, J. J.↗
NASA NTRS1984

Fuel savings potential of the NASA Advanced Turboprop Program

The NASA Advanced Turboprop (ATP) Program is directed at developing new technology for highly loaded, multibladed propellers for use at Mach 0.65 to 0.85 and at altitudes compatible with the air transport system requirements. Advanced turboprop engines offer the potential of 15 to 30 percent savings in aircraft block fuel relative to advanced turbofan engines (50 to 60 percent savings over today's turbofan fleet). The concept, propulsive efficiency gains, block fuel savings and other benefits, and the program objectives through a systems approach are described. Current program status and major accomplishments in both single rotation and counter rotation propeller technology are addressed. The overall program from scale model wind tunnel tests to large scale flight tests on testbed aircraft is discussed.

Whitlow, J. B., Jr.↗
NASA NTRS1984

Advanced propfan drive system characteristics and technology needs

Characteristics of a single-rotation drive system for an advanced turboprop engine are described. The gearbox is designed for a 10,000 shp three-spool, free-turbine engine and is installed in a wing-mounted nacelle. An offset gearbox from an earlier APET study provided the background for the preliminary design and benefit analysis for a 1990s advanced technology versus 1980s state-of-the-art gearbox. High efficiencies were achieved for both designs with inherently high life goals. Increases in design allowables for gears, bearings, and lubricants resulted in improvements for the 1990s design.

Anderson, R. D.↗
NASA NTRS1985

An improved source model for aircraft interior noise studies

There is concern that advanced turboprop engines currently being developed may produce excessive aircraft cabin noise levels. This concern has stimulated renewed interest in developing aircraft interior noise reduction methods that do not significantly increase take off weight. An existing analytical model for noise transmission into aircraft cabins was utilized to investigate the behavior of an improved propeller source model for use in aircraft interior noise studies. The new source model, a virtually rotating dipole, is shown to adequately match measured fuselage sound pressure distributions, including the correct phase relationships, for published data. The virtually rotating dipole is used to study the sensitivity of synchrophasing effectiveness to the fuselage sound pressure trace velocity distribution. Results of calculations are presented which reveal the importance of correctly modeling the surface pressure phase relations in synchrophasing and other aircraft interior noise studies.

Mahan, J. R.↗
NASA NTRS1985

Flight-measured laminar boundary-layer transition phenomena including stability theory analysis

Flight experiments were conducted on a single-engine turboprop aircraft fitted with a 92-in-chord, 3-ft-span natural laminar flow glove at glove section lift coefficients from 0.15 to 1.10. The boundary-layer transition measurement methods used included sublimating chemicals and surface hot-film sensors. Transition occurred downstream of the minimum pressure point. Hot-film sensors provided a well-defined indication of laminar, laminar-separation, transitional, and turbulent boundary layers. Theoretical calculations of the boundary-layer parameters provided close agreement between the predicted laminar-separation point and the measured transition location. Tollmien-Schlichting (T-S) wave growth n-factors between 15 and 17 were calculated at the predicted point of laminar separation. These results suggest that for many practical airplane cruise conditions, laminar separation (as opposed to T-S instability) is the major cause of transition in predominantly two-dimensional flows.

Obara, C. J.↗
NASA NTRS1985

Fundamental studies of structure borne noise for advanced turboprop applications

The transmission of sound generated by wing-mounted, advanced turboprop engines into the cabin interior via structural paths is considered. The structural model employed is a beam representation of the wing box carried into the fuselage via a representative frame type of carry through structure. The structure for the cabin cavity is a stiffened shell of rectangular or cylindrical geometry. The structure is modelled using a finite element formulation and the acoustic cavity is modelled using an analytical representation appropriate for the geometry. The structural and acoustic models are coupled by the use of hard wall cavity modes for the interior and vacuum structural modes for the shell. The coupling is accomplished using a combination of analytical and finite element models. The advantage is the substantial reduction in dimensionality achieved by modelling the interior analytically. The mathematical model for the interior noise problem is demonstrated with a simple plate/cavity system which has all of the features of the fuselage interior noise problem.

Eversman, W.↗
NASA NTRS1984

Noise transmission through an acoustically treated and honeycomb stiffened aircraft sidewall

The noise transmission characteristics of test panels and acoustic treatments representative of an aircraft sidewall are experimentally investigated in the NASA Langley Research Center transmission loss apparatus. The test panels were built to represent a segment sidewall in the propeller plane of a twin-engine, turboprop light aircraft. It is shown that an advanced treatment, which uses honeycomb for structural stiffening of skin panels, has better noise transmission loss characteristics than a conventional treatment. An alternative treatment, using the concept of limp mass and vibration isolation, provides more transmission loss than the advanced treatment for the same total surface mass. Effects on transmission loss of a variety of acoustic treatment materials (acoustic blankets, septa, damping tape, and trim panels) are presented. Damping tape does not provide additional benefit when the other treatment provides a high level of damping. Window units representative of aircraft installations are shown to have low transmission loss relative to a completely treated sidewall.

Grosveld, F. W.↗
NASA NTRS1985

An improved source model for aircraft interior noise studies

There is concern that advanced turboprop engines currently being developed may produce excessive aircraft cabin noise level. This concern has stimulated renewed interest in developing aircraft interior noise reduction methods that do not significnatly increase take off weight. An existing analytical model for noise transmission into aircraft cabins was utilized to investigate the behavior of an improved propeller source model for use in aircraft interior noise studies. The new source model, a virtually rotating dipole, is shown to adequately match measured fuselage sound pressure distributions, including the correct phase relationships, for published data. The virtually rotating dipole is used to study the sensitivity of synchrophasing effectiveness to the fuselage sound pressure trace velocity distribution. Results of calculations are presented which reveal the importance of correctly modeling the surface pressure phase relations in synchrophasing and other aircraft interior noise studies.

Mahan, J. R.↗
NASA NTRS1986

Comparison of two propeller source models for aircraft interior noise studies

The sensitivity of the predicted synchrophasing (SP) effectiveness trends to the propeller source model issued is investigated with reference to the development of advanced turboprop engines for transport aircraft. SP effectiveness is shown to be sensitive to the type of source model used. For the virtually rotating dipole source model, the SP effectiveness is sensitive to the direction of rotation at some frequencies but not at others. The SP effectiveness obtained from the virtually rotating dipole model is not very sensitive to the radial location of the source distribution within reasonable limits. Finally, the predicted SP effectiveness is shown to be more sensitive to the details of the source model used for the case of corotation than for the case of counterrotation.

Mahan, J. R.↗
NASA NTRS1988

In-flight flow visualization using infrared imaging

A flight test investigation was conducted to evaluate infrared (IR) flow imaging techniques for boundary-layer flow visualization. The flight tests used a single-engine turboprop aircraft with a fiberglass-skinned natural laminar flow glove mounted on the left wing and an infrared imaging system to obtain flow visualization data. Data were compared to results obtained from other more conventional boundary-layer flow visualization methods and found to agree well. Test flights were conducted to determine the effect of test surface color on IR flow visualization results. In addition, flights were made during both night and daylight hours to assess the effect of solar radiation on the results. The investigation included an effort to visualize a vortex passing over the wing glove, but the tests provided only limited results.

Brandon, J. M.↗