Search NASA⌕ Search

SEARCH · Search NASA

Results for “Task 36”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Validation Exercise of a Coarse Finite Element Model of Laser Welds

The objective of this project is to validate low-fidelity models of 304L to 304L stainless steel partial-penetration laser welds for thin sheets. Low-fidelity means that the weld is represented by coarsely meshed element blocks. Here, the hexahedral element size is approx imately half the weld penetration depth. The material behavior of the block is represented by a J2 plasticity model with a Voce hardening function. The source of the data used in this work is an extensive experimental study conducted by Sharlotte Kramer (1528) and published in 2015. Figure 1 shows a cross-section of the weld of interest. The nominal thickness of the sheets is 0.063 in. while the target penetration depth of the weld is in the range of 0.028 to 0.032 in., extending about half the sheet thickness. Uniaxial tension tests provided data for calibration of base material and weld models. Results of two validation geometries were also provided. The principal validation geometry is shown in Fig. 2. It consists of a plate specimen with in-plane dimensions 6 in × 2.875 in loaded in tension. A circular plug with a 1.5 in. diameter was cut from the center of the plate and then welded in place. The details of the welding schedule are given. An important assumption is that the welds in the calibration and validation specimens have similar geometric and material properties as those in the validation tests. The task was to first calibrate models for the base material and the welds and then simulate the validation tests until the point of weld first failure.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Multi-pack Disposal Concepts for Spent Fuel (Rev. 0)

At the initiation of the Used Fuel Disposition (UFD) R&D campaign, international geologic disposal programs and past work in the U.S. were surveyed to identify viable disposal concepts for crystalline, clay/shale, and salt host media (Hardin et al., 2012). Concepts for disposal of commercial spent nuclear fuel (SNF) and high-level waste (HLW) from reprocessing are relatively advanced in countries such as Finland, France, and Sweden. The UFD work quickly showed that these international concepts are all “enclosed,” whereby waste packages are emplaced in direct or close contact with natural or engineered materials . Alternative “open” modes (emplacement tunnels are kept open after emplacement for extended ventilation) have been limited to the Yucca Mountain License Application Design (CRWMS M&O, 1999). Thermal analysis showed that, if “enclosed” concepts are constrained by peak package/buffer temperature, waste package capacity is limited to 4 PWR assemblies (or 9-BWR) in all media except salt. This information motivated separate studies: 1) extend the peak temperature tolerance of backfill materials, which is ongoing; and 2) develop small canisters (up to 4-PWR size) that can be grouped in larger multi-pack units for convenience of storage, transportation, and possibly disposal (should the disposal concept permit larger packages). A recent result from the second line of investigation is the Task Order 18 report: Generic Design for Small Standardized Transportation, Aging and Disposal Canister Systems (EnergySolution, 2015). This report identifies disposal concepts for the small canisters (4-PWR size) drawing heavily on previous work, and for the multi-pack (16-PWR or 36-BWR).

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2018

Defense Waste Processing Facility Canister Closure Weld Current Validation Testing

Two closure welds on filled Defense Waste Processing Facility (DWPF) canisters failed to be within the acceptance criteria in the DWPF operating procedure SW4-15.80-2.3 (1). In one case, the weld heat setting was inadvertently provided to the canister at the value used for test welds (i.e., 72%) and this oversight produced a weld at a current of nominally 210 kA compared to the operating procedure range (i.e., 82%) of 240 kA to 263 kA. The second weld appeared to experience an instrumentation and data acquisition upset. The current for this weld was reported as 191 kA. Review of the data from the Data Acquisition System (DAS) indicated that three of the four current legs were reading the expected values, approximately 62 kA each, and the fourth leg read zero current. Since there is no feasible way by further examination of the process data to ascertain if this weld was actually welded at either the target current or the lower current, a test plan was executed to provide assurance that these Nonconforming Welds (NCWs) meet the requirements for strength and leak tightness. Acceptance of the welds is based on evaluation of Test Nozzle Welds (TNW) made specifically for comparison. The TNW were nondestructively and destructively evaluated for plug height, heat tint, ultrasonic testing (UT) for bond length and ultrasonic volumetric examination for weld defects, burst pressure, fractography, and metallography. The testing was conducted in agreement with a Task Technical and Quality Assurance Plan (TTQAP) (2) and applicable procedures.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Lab Scale Mercury Dissolution Testing

Researchers at the Savannah River National Laboratory were requested by Savannah River Mission Completion to perform laboratory testing and modeling designed to understand why the Defense Waste Processing Facility (DWPF) is not collecting elemental mercury (Hg 0 ) despite long boiling times designed to recover Hg 0 . In response to a Technical Task Request, a Task Technical and Quality Assurance Plan was written and approved to authorize this work.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Low-cost Manufacturing of Semitransparent CdTe PV for Building Integration

Solar has been demonstrated to be a robust renewable energy source, constituting a significant portion of the United States’ renewable energy portfolio. Despite its growth across residential, commercial, and utility sectors over the past decades, it remains a small fraction of the overall energy infrastructure. Challenges persist in fully harnessing solar power to meet the nation's escalating energy demands. Among these challenges lies the hurdle of efficiently distributing large quantities of solar-generated electricity to densely populated regions with the highest energy needs and costs. Traditional utility-scale arrays demand extensive land, a luxury often unavailable in metropolitan areas. Consequently, installations must be situated at a distance, necessitating additional infrastructure for electricity transmission to service areas. While metropolitan landscapes lack sprawling open spaces suitable for conventional utility-scale solar deployment, they offer a different resource: windows. Semitransparent photovoltaic window technology has the potential to not only bolster the grid's energy capacity, but to also provide HVAC and economic advantages to building owners. However, commercial availability of building-integrated photovoltaic windows remains limited. Silicon based photovoltaics currently dominate the solar market but adapting them for use in windows poses a variety of engineering and economic challenges such as relatively low power density, high costs associated with custom manufacturing, and aesthetic considerations. Addressing these challenges, this project explored the use of laser ablation patterning to manufacture cost-effective, high-efficiency, semitransparent Cadmium Telluride photovoltaic modules. Results showcased the potential of this methodology in developing photovoltaic windows and other innovative semitransparent PV applications. The ablation manufacturing technique demonstrated great versatility in achieving different patterns and levels of visible light transmission, and the power loss due to ablation was nearly directly proportional to the amount of material removed. Furthermore, the manufacturing process for Cadmium Telluride modules already has established advantages in material and energy efficiency, and the conversion of a standard submodule to semitransparent essentially requires a single additional process step, ensuring scalability. It is important to note that during this work, Toledo Solar experienced substantial organizational upheaval stemming from a lawsuit with First Solar. An external investigation led the board of directors to remove and replace the previous management team, and several other members of the staff elected to depart as well, including the then acting Principle Investigator on this project. The remaining Toledo Solar team attempted to recover from the disruption and deliver on the remaining tasks, but upon its own review, the Department of Energy ruled the project in default and terminated the contract in December 2023.

14 SOLAR ENERGY↗
DOE OSTI2017

Complete Status Report Documenting Development of Friction Stir Welding for Joining Thin Wall Tubing of ODS Alloys

The development of friction stir welding (FSW) for joining thin sections of the advanced oxide dispersion strengthened (ODS) 14YWT ferritic alloy was initiated in Fuel Cycle Research and Development (FCRD), now the Nuclear Technology Research and Development (NTRD), in 2015. The first FSW experiment was conducted in late FY15 and successfully produced a bead-on-plate stir zone (SZ) on a 1 mm thick plate of 14YWT (SM13 heat). The goal of this research task is to ultimately demonstrate that FSW is a feasible method for joining thin wall (0.5 mm thick) tubing of 14YWT.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Degradable Biocomposite Thermoplastic Polyurethanes

In this project, the team developed tough and degradable biocomposite thermoplastic polyurethanes (TPUs) by incorporating bacterial spores into TPUs as a biofunctional living filler. The team screened various bacteria and selected the Bacillus subtilis ATCC 6633 strain as the final candidate, primarily due to its genomic availability, sporulation ability and TPU assimilation activity. The heat-shock tolerance of ATCC 6633 spores was further improved through evolutionary engineering via Adaptive Laboratory Evolution (ALE), demonstrating a 17.7-fold enhanced germination efficiency post heat-shock treatment compared to the wild-type strain (WT). The team fabricated biocomposite TPUs by incorporating lyophilized powder of heat-shock tolerized (HST) spores during the hot melt extrusion (HME) of TPU at 135 °C. The baseline TPU used in this project is a commercially available soft-grade TPU (BCF45) manufactured by BASF. Colony forming unit (CFU) assays quantified that WT and HST spores in the TPU matrix retained approximately 20% and 100% survivability, respectively, after HME. Tensile testing demonstrated that the spores behaved as a polymer-reinforcing filler, positively affecting the overall tensile properties of the biocomposite TPU. For example, biocomposite TPU with WT and HST spores (BC TPU WT and BC TPU HST , respectively) exhibited up to 25% and 37% improved toughness, respectively, compared to TPU without spores. BC TPU HST showed remarkably improved disintegration in autoclaved compost (92% mass loss in 5 months), which simulated a microbially poor environment for TPU degradation. When compared to TPU without spores (44% mass loss in 5 months) the acceleration of degradation is marked. Respirometry confirmed that 72% of BC TPU HST was biomineralized into CO2 within 6 months, indicating that spores in the biocomposite TPU were germinated by utilizing nutrients in the autoclaved compost, facilitating TPU degradation at the end of the material's life. The team demonstrated the scale-up of biocomposite TPU fabrication using continuous extrusion and injection molding techniques. Processing conditions optimized in a lab-scale microcompounder were successfully transferred to a continuous extruder with a 30-fold increased throughput. Biocomposite TPUs prepared using these industry-relevant processes showed comparable toughness improvements to samples prepared in the lab-scale extruder. Excitingly, following compounding in the pilot-extruder the composite material could be injection molded, while retaining high spore viability and similar toughness improvements. The team also found that spores in biocomposite TPU served as antioxidants, preventing toughness decay during the recycled extrusion of BC TPU HST . Long-term storage tests over one year showed that the addition of spores had no negative effect on the longevity of the TPU. Furthermore, the team demonstrated the fabrication of spore-bearing biocomposite polymers with other polyesters such as PBAT, PLA, and PCL. We obtained promising preliminary data that showed overall toughness improvements for all polymers with spore addition. Finally, life cycle assessment (LCA) and techno-economic analysis (TEA) were carried out, which indicated minimal additional cost of fabrication. Overall, a tough and degradable biocomposite thermoplastic was successfully developed through this project, with all tasks completed successfully, achieving >100% of the objectives.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multi-fidelity Uncertainty Quantification for Homogenization Problems in Structure-Property Relationships from Crystal Plasticity Finite Elements

Crystal plasticity finite element method (CPFEM) has been an integrated computational materials engineering (ICME) workhorse to study materials behaviors and structure-property relationships for the last few decades. These relations are mappings from the microstructure space to the materials properties space. Due to the stochastic and random nature of microstructures, there is always some uncertainty associated with materials properties, for example, in homogenized stress-strain curves. For critical applications with strong reliability needs, it is often desirable to quantify the microstructure-induced uncertainty in the context of structure-property relationships. However, this uncertainty quantification (UQ) problem often incurs a large computational cost because many statistically equivalent representative volume elements (SERVEs) are needed. In this article, we apply a multi-level Monte Carlo (MLMC) method to CPFEM to study the uncertainty in stress-strain curves, given an ensemble of SERVEs at multiple mesh resolutions. By using the information at coarse meshes, we show that it is possible to approximate the response at fine meshes with a much reduced computational cost. We focus on problems where the model output is multi-dimensional, which requires us to track multiple quantities of interest (QoIs) at the same time. In conclusion, our numerical results show that MLMC can accelerate UQ tasks around 2.23x, compared to the classical Monte Carlo (MC) method, which is widely known as ensemble average in the CPFEM literature.

36 MATERIALS SCIENCE↗
DOE OSTI2024

RESIN: Responsible Innovation for Highly Recyclable Plastics - TASK 4: Risk Assessment Framework

This report covers the entirety of Task 4, but its main purpose is to deliver milestones ML4.4 and ML4.5, the last two SOPO milestones under Task 4. ML4.4 reports on the compatibility of polymer properties that affect both environmental performance and functional performance and the tradeoffs involved in turning these properties to the benefit of each. ML4.5 presents a complete set of information on the critical properties of benign target products, where benign products are defined as those with the shortest environmental lifetime which meet performance requirements. To support and provide context to the discussions of ML4.4 and ML4.5 and to provide a complete picture of Task 4, milestones 4.1-4.3 are briefly summarized at the beginning of the report. The discussion of ML4.4 introduces the notion of polymer persistence as a proxy for environmental risk. It then discusses the development and comparison of two machine leaning models explored for estimating polymer degradation rates, a random forest (RF) classifier and an RF regressor. Given the advantage of continuous outputs rather than simple classes, the RF regressor was incorporated in the Excel risk calculator, which to this point could implement the objectives of subtasks 4.1-4.3, estimating polymer release and redistribution. The ML4.4 discussion then addresses the effect of each of the three polymer features used by the RF regressor on polymer functional performance. These features are number molecular weight (Mn), glass transition temperature (T g ) and heat of fusion (H fus ). The discussion of ML4.5 reviews the conceptual framework of the risk model, which served as the foundation for developing the Excel risk calculator and describes the use of, and assumptions within, the calculator. Appendix A is further provided as a user’s guide for the calculator. To demonstrate how the calculator is intended to be used by developers in the design of low-risk polymers, an analysis of 27 hypothetical polymers defined by varying values for the three polymer features used by the RF regressor is presented. The range of parameter values selected produces estimates of polymer degradation rates and lifetimes that may be typical of various consumer products made from polyurethane polymers and shows how changes in polymer features affect lifetimes. The demonstration also predicts the final distribution of released polymer materials in environmental compartments as a function of consumer product mix and assumed leakage rates of end-of-life processes. Lastly, this report summarizes the achievement of Task 4 goals from original conception to final delivery and discusses how and to what degree to which each subtask goal was achieved.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Demonstration of a prototype hydrogen sensor and electronics package

This is a progress report for the demonstration of a prototype hydrogen sensor and electronics package. There are five tasks associated with this, and four have been completed as of August 2016: Station Demonstration and Site Recommendation, Order Sensor Equipment, Build Sensors, and Install Sensors. The final task to be completed is Sensor Demonstration and Data Analysis, and expected completion date is January 26, 2017. This progress report details each of the tasks and goes into detail about what is currently being worked on, along with the budget and planned work for July 27, 2016 to January 26, 2017.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Remaining Life Determination

This project developed and demonstrated the capability of nondestructive evaluation methods for detecting early stage fatigue damage in grey cast iron metal. Non-collinear ultrasonic wave mixing and laser speckle differentiation were the primary technologies evaluated on custom fatigue specimens having properties specified by Caterpillar, Inc. The ultrasonic method showed the greatest potential for estimating the remaining fatigue life in grey cast iron, which may provide remanufacturers with a level of confidence when fielding used component cores in high-stress applications. While successes were realized during this project, there are still follow-on research tasks required to prove the commercial applicability of the methods. The following report sections document the steps completed during the project and an assessment of the technologies applied.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Thermodynamics and Kinetics of Phase Transformations in Energy Materials (Final Report)

The primary goal of this program is to develop computational tools and methodology for enabling a shift from empirical trial-and-error driven materials discovery towards data and information technology driven design of materials with targeted functional properties. Both thermodynamic and kinetic factors need to be taken into account when designing new materials. Thermodynamics sets the necessary-but-not-sufficient conditions for the suitability of a particular material in a given application, while the kinetics controls the rates of microscopic processes and hence the performance in energy applications (e.g., power in energy storage, conversion efficiencies in solar cells and thermoelectrics, chemical activity in catalysis). The complexity of these phenomena makes computational design difficult, not least due to the lack of suitable theoretical methods and computational tools. To address these needs, we develop systematic, quantitatively accurate first-principles methods to address two important problems: (i) predict and optimize the thermodynamics of materials over a large composition and structure space, and (ii) model kinetic processes such as mass and heat transport in crystalline solids under non-equilibrium conditions. These tasks are addressed by combining high-throughput computation with automatic construction of accurate lattice models using mathematically rigorous methods of information theory, such as compressive sensing and Bayesian inference.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Manufacturability Advancement of Low-Temperature Titanium Electroplating Methods

Three tasks were proposed for this work. All three were completed. The tasks were as follows: Task 1: A larger plating system will be purchased for process scale-up. TiF 3 will be tested as the metal precursor in an effort to reduce water sensitivity of the process. Task 2: Ti on steel samples will be created at PNNL and shipped to Atlas Technologies. Atlas Technologies will diffusion bond the samples to aluminum and test the bond strength. The results will be reported to PNNL. Task 3: Investigation into DOE mission relevant Ti and Zr alloys and demonstration on larger scale work pieces.

36 MATERIALS SCIENCE↗
DOE OSTI2016

FY16 ASME High Temperature Code Activities

One of the objectives of the ASME high temperature Code activities is to develop and validate both improvements and the basic features of Section III, Division 5, Subsection HB, Subpart B (HBB). The overall scope of this task is to develop a computer program to be used to assess whether or not a specific component under specified loading conditions will satisfy the elevated temperature design requirements for Class A components in Section III, Division 5, Subsection HB, Subpart B (HBB). There are many features and alternative paths of varying complexity in HBB. The initial focus of this task is a basic path through the various options for a single reference material, 316H stainless steel. However, the program will be structured for eventual incorporation all the features and permitted materials of HBB. Since this task has recently been initiated, this report focuses on the description of the initial path forward and an overall description of the approach to computer program development.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Representations of Materials for Machine Learning

High-throughput data generation methods and machine learning (ML) algorithms have given rise to a new era of computational materials science by learning the relations between composition, structure, and properties and by exploiting such relations for design. However, to build these connections, materials data must be translated into a numerical form, called a representation, that can be processed by an ML model. Data sets in materials science vary in format (ranging from images to spectra), size, and fidelity. Predictive models vary in scope and properties of interest. Here, we review context-dependent strategies for constructing representations that enable the use of materials as inputs or outputs for ML models. Furthermore, we discuss how modern ML techniques can learn representations from data and transfer chemical and physical information between tasks. Finally, we outline high-impact questions that have not been fully resolved and thus require further investigation.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Hanford Double Shell Waste Tank Corrosion Studies - Final Report FY2015

During FY15, SRNL performed corrosion testing that supported Washington River Protection Solutions (WRPS) with their double shell tank (DST) integrity program. The testing investigated six concerns including, 1) the possibility of corrosion of the exterior of the secondary tank wall; 2) the effect of ammonia on vapor space corrosion (VSC) above waste simulants; 3) the determination of the minimum required nitrite and hydroxide concentrations that prevent pitting in concentrated nitrate solutions (i.e., waste buffering); 4) the susceptibility to liquid air interface (LAI) corrosion at proposed stress corrosion cracking (SCC) inhibitor concentrations; 5) the susceptibility of carbon steel to pitting in dilute solutions that contain significant quantities of chloride and sulfate; and 6) the effect of different heats of A537 carbon steel on the corrosion response. For task 1, 2, and 4, the effect of heat treating and/ or welding of the materials was also investigated.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗