SEARCH · Search NASA

Results for “Trailing-Edge”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1937

Wind-tunnel tests of a Clark Y wing with 'Maxwell' leading-edge slots

Aerodynamic force tests of a Clark Y wing equipped with "Maxwell" type leading-edge slots were conducted in the N.A.C.A. 7- by 10-foot tunnel to ascertain the aerodynamic characteristics, which involved the determination of the best slot-gap opening, the effects of slat width, and the effect of a trailing-edge flap. The Maxwell wing with a wide-chord slat (0.30 c(sub w)) and with a 0.211 c(sub w) split flap deflected 60 degrees had a C(sub L sub max) of 2.53 or about twice that of the plain wing. The wing with the wide slat also had, in general, improved aerodynamic characteristics over those of the Maxwell wing with slat, and had about the same aerodynamic characteristics as a Handley Page slotted wing with approximately the same size of slat.

Gauvain, William E↗

NASA NTRS1937

Full Scale Span Load Distribution on a Tapered Wing with Split Flaps of Various Spans

Pressure-distribution tests were conducted in the full-scale wind tunnel on a 2:1 tapered U.S.A. 45 airfoil equipped with 20 percent chord split trailing-edge flaps of various spans. A special installation was employed in the tests utilizing a half-span airfoil mounted vertically above a reflection plane. The airfoil has a constant chord center section and rounded tips and is tapered in thickness from 18 percent c at the root to 9 percent c at the tip. The aerodynamic characteristics, given by the usual dimension less coefficients, are presented graphically as functions of flap span and angle of attack as well as by semispan load diagrams. The results indicate, in general, that only a relatively small increase in the normal-force coefficient is to be expected by extending the flap span of an airfoil-flap combination, similar to the one tested, beyond 70 percent of the wing span.

Parsons, John F↗

NASA NTRS1938

Tests of N-85, N-86 and N-87 airfoil sections in the 11-inch high speed wind tunnel

Three airfoils, the N-85, the N-86, and the N-87, were tested at the request of the Bureau of Aeronautics, Navy Department, to determine the suitability of these sections for use as propeller-blade sections. Further tests of the NACA 0009-64 airfoil were also made to measure the aerodynamic effect of thickening the trailing edge in accordance with current propeller practice. The N-86 and the N-87 airfoils appear to be nearly equivalent aerodynamically and both are superior to the N-85 airfoil. Comparison of those airfoils with the previously developed NACA 2409-34 airfoils indicate that the NACA 2409-34 is superior, particularly at high speeds. Thickening the trailing edge appears to have a detrimental effect, although the effect may be small if the trailing-edge radius is less than 0.5 percent of the cord. The N-86 and the N-87 airfoils appear to be nearly equivalent.

Stack, John↗

NASA NTRS1948

The Development of Cambered Airfoil Sections Having Favorable Lift Characteristics at Supercritical Mach Numbers

Several groups of new airfoil sections, designated as the NACA 8-series, are derived analytically to have lift characteristics at supercritical Mach numbers which are favorable in the sense that the abrupt loss of lift, characteristic of the usual airfoil section at Mach numbers above the critical, is avoided. Aerodynamic characteristics determined, from two-dimensional windtunnel tests at Mach numbers up to approximately 0.9 are presented for each of the derived airfoils. Comparisons are made between the characteristics of these airfoils and the corresponding characteristics of representative NPiCA 6-series airfoils. The experimental results confirm the design expectations in demonstrating for the NACA S-series airfoils either no variation, or an Increase from the low-speed design value, In the lift coefficient at a constant angle of attack with increasing Mach number above the critical. It was not found possible to improve the variation with Mach number of the slope of the lift curve for these airfoils above that for the NACA 6-series airfoils. The drag characteristics of the new airfoils are somewhat inferior to those of the NACA 6- series with respect to divergence with Mach number, but the pitching-moment characteristics are more favorable for the thinner new sections In demonstrating somewhat smaller variations of moment coefficient with both angle of attack and Mach number. The effect on the aero&ynamic characteristics at high Mach numbers of removing the cusp from the trailing-edge regions of two 10-percent-chord-thick NACA 6-series airfoils is determined to be negligible.

AIRFOILS - NACA 836B110 - CHAR , MOMENTS & ORDINAT↗

NASA NTRS1957

Perforated Sheets as the Porous Material for a Suction-flap Application

Two-dimensional tests were made of an NACA 0006 airfoil with area suction applied to a porous region on a 0.3-chord trailing-edge flap deflected 50 degrees. The lift with suction approached the value computed from thin-airfoil theory. The lift gains and suction quantity requirements were unaffected by the perforation patterns of the surface over a wide range of hole sizes and spacings.

MATERIALS - TYPES↗

NASA NTRS1933

Wind-tunnel tests on model wing with Fowler flap and specially developed leading-edge slot

An investigation was made in the NACA 7 by 10 foot wind tunnel to find the increase in maximum lift coefficient which could be obtained by providing a model wing with both a Fowler trailing-edge extension flap and a Handley Page type leading-edge slot. A conventional Handley page slot proportioned to operate on the plain wing without a flap gave but a slight increase with the flap; so a special form of slot was developed to work more effectively with the flap. With the best combined arrangement the maximum lift coefficient based on the original area was increased from 3.17, for the Fowler wing, to 3.62. The minimum drag coefficient with both devices retracted was increased in approximately the same proportion. Tests were also made with the special-type slot on the plain wing without the flap. The special slot, used either with or without the Fowler flap, gave definitely higher values of the maximum lift coefficient than the slots of conventional form, with an increase of the same order in the minimum drag coefficient.

WING SLOTS & FLAPS, FOWLER↗

NASA NTRS1933

Wind-tunnel research comparing lateral control devices, particularly at high angles of attack IV : floating tip ailerons on rectangular wings

This report is the fourth of a series on systematic tests conducted which compares lateral control devices with particular reference to their effectiveness at high angles of attack. The present report covers tests with floating tip ailerons on rectangular Clark y wings. Ailerons of two profiles were tested - symmetrical and Clark y, both with adjustable trailing-edge flaps. Each form was tested at three hinge-axis locations, both with and without vertical end plates between the ailerons and the wing proper. The results from these tests are compared with the results from tests on a wing of the same over-all size equipped with average-sized ordinary ailerons.

Weick, Fred E↗

NASA NTRS1936

Flight Investigation of Lateral Control Devices for Use with Full-Span Flaps

This report presents the results of flight tests made on five different lateral control devices that appeared adaptable to wings fitted with full span flaps: controllable auxiliary airfoils (airfoils mounted above and forward of the leading edge of the wings), external ailerons (airfoils mounted above the wing and slightly forward of its maximum ordinate), upper-surface ailerons (similar to split trailing-edge flaps except that they constitute the upper surface of the wing), ailerons that retract into the wing when in neutral, and narrow-chord conventional ailerons in combination with a special type of split flap that retracts into the under surface of the wing forward of the ailerons. The devices were tested on a small parasol monoplane. Experienced gained in the use of flaps during these tests has indicated the desirability of a flap that can be operated quickly and easily.

Soule, H A↗

NASA NTRS1948

Theoretical and experimental data for a number of NACA 6A-series airfoil sections

The NACA 6a-series airfoil sections were designed to eliminate the trailing-edge cusp which is characteristic of the NACA 6a-series sections. Theoretical data are presented for NACA 6a-series basic thickness forms having the position of minimum pressure of 30, 40, and 50 percent chord and with thickness ratios varying from 6 percent to 15 percent. Also presented are data for a mean line designed to maintain straight sides on the cambered sections.

Loftin, Laurence K , Jr↗

NASA NTRS1947

Two-Dimensional Wind-Tunnel Investigation of Modified NACA 65(112)-111 Airfoil with 35-Percent-Chord Slotted Flap to Determine Optimum Flap Configuration at Reynolds Number of 2.4 Million

An investigation has been made in the Langley two-dimensional low-turbulence tunnel to develop the optimum configuration of a 0.35-chord slotted flap on an NACA 65 (112)-111 airfoil section modified by removing the trailing-edge cusp. The results of the investigation indicate that for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6), the flap deflection was 45 degrees and the flap leading-edge radius center was 0.73 percent-chord behind and 4.46 percent-chord below the slot lip. The maximum section lift coefficient for the optimum configuration at a Reynolds number of 2.4 x 10(exp 6) was 2.46 or 0.12 higher than that obtained for an NACA 65-210 airfoil section with a 0.250-chord slotted flap.

Racisz, Stanley F.↗

NASA NTRS1947

Two-Dimensional Wind-Tunnel Investigation of Modified NACA 65(sub 112)-111 Airfoil with 35-Percent-Chord Slotted Flap to Determine Pitching-Moment Characteristics and Effects of Roughness

An investigation has been made in the Langley two-dimensional low-turbulence pressure tunnel to develop the optimum configuration of a 0.35-chord slotted flap on an NACA 65(sub 1120)-111 airfoil section modified by removing the trailing-edge cusp. The section pitching-moment characteristics and the effects of standard roughness on the section characteristics were determined for the flap retracted at Reynolds numbers ranging from 3.0 x 10(exp 6) to 9.0 x 10(exp 6).

Racisz, Stanley F.↗

NASA NTRS1947

Two-Dimensional Wind-Tunnel Investigation of Modified NACA 65(sub 112)-111 Airfoil with 35-Percent-Chord Slotted Flap at Reynolds Numbers up to 25 Million

An investigation has been made in the Langley two-dimensional low-turbulence tunnels to develop the optimum configuration of a .035-chord slotted flap on an NACA 65(sub(112)-111 airfoil section modified by removing the trailing-edge cusp. Included in the investigation were measurements to determine the scale effects on the section lift and drag characteristics of the airfoil with the flap retracted for Reynolds numbers ranging from 3.0 X 10(exp 6) to 2.5 X 10(exp 6). The scale effects on the lift characteristics were also determined for the same reynolds numbers for the flap deflected in the rotation found to be optimum at a Reynolds number of 9.0 X 10(exp 6).

Racisz, Stanley F.↗

NASA NTRS1946

Theoretical and Experimental Data for a Number of NACA 6A-Series Airfoil Sections

The NACA 6A-series airfoil sections were designed to eliminate the trailing-edge cusp which is characteristic of the NACA 6-series sections. Theoretical data are presented for NACA 6A-series basic thickness forms having the position of minimum pressure at 30-, 40-, and 50-percent chord and with thickness ratios varying from 6 percent to 15 percent. Also presented are data for a mean line designed to maintain straight sides on the cambered sections. The experimental results of a two dimensional wind tunnel investigation of the aerodynamic characteristics of five NACA 64A-series airfoil sections and two NACA 63A-series airfoil sections are presented. An analysis of these results, which were obtained at Reynolds numbers of 3 x 10(exp 6), 6 x 10(exp 6), and 9 x 10(exp 6), indicates that the section minimum drag and maximum lift characteristics of comparable NACA 6-series and 6A-series airfoil sections are essentially the same. The quarter-chord pitching-moment coefficients and angles of zero lift of NACA 6A-series airfoil sections are slightly more negative than those of corresponding NACA 6-series airfoil sections. The position of the aerodynamic center and the lift-curve slope of smooth NACA 6-series sections. The addition of standard leading-edge roughness causes the lift-curve slope of the newer sections to decrease with increasing airfoil thickness ratio.

Loftin, Laurence K., Jr.↗

NASA NTRS1942

Preliminary Wind-Tunnel Tests of the Effect of Nacelles on the Characteristics of a Twin-Engine Bomber Model with Low-Drag Wing, Special Report

Tests were made in the NACA 19-foot pressure tunnel of a simplified twin-engine bomber model with an NACA low-drag wing primarily to obtain an indication of the effects of engine nacelles on the characteristics of the model both with and without simple split trailing-edge flaps. Nacelles with conventional-type cowlings representative of those used on an existing high-performance airplane and with NACA high-speed type E cowlings were tested. The tests were made without propeller slipstream. The aerodynamic effects of adding the nacelles to the low-drag wing were similar to the effects commonly obtained by adding similar nacelles to conventional wings. The maximum lift coefficient without flaps was slightly increased, but the increment in maximum lift due to deflecting the flaps was somewhat decreased. The stalling characteristics were improved by the presence of the nacelles. Addition of the nacelles had a destabilizing effect on the pitching moments, as is usual for nacelles that project forward of the wing. The drag increments due to the nacelles were of the usual order of magnitude, with the increment due to the nacelles with NACA type E cowlings approximately one-third less than that of the nacelles with conventional cowlings with built-in air scoops.

Wenzinger, Carl J.↗

NASA NTRS1949

High Speed Stability and Control Characteristics of a 0.17-Scale Model of the McDonnell XF2H-1 Airplane (TED No. NACA DE 318)

High-speed wind-tunnel tests were conducted of two versions of a 0.17-scale model of the McDonnell XF2H-1 airplane to ascertain the high-speed stability and control characteristics and to study means for raising the high-speed buffet limit of the airplane, The results for the revised model, employing a thinner wing and tail than the original model, revealed a mild diving tendency from 0.75 to 0.80 Mach number, followed by a marked climbing tendency from 0.80 to 0.875 Mach number. The high-speed climbing tendency was caused principally by the pitching-moment characteristics of the wing. At 0.875 Mach number the results for the revised model indicated stick-fixed directional instability over a limited range of yaw angles, apparently caused by separated flow over the vertical tail. The test results indicate that the high-speed buffet limit of the airplane can probably be raised by reducing the thickness and changing the relative location of the horizontal and vertical tails, and by revising the inner portion of the wing to have a lower thickness-to-chord ratio and reduced trailing-edge angle. The addition of the wing-tip tanks to the revised model resulted in a forward shift in the neutral point below 0.82 Mach number.

Axelson, John A.↗

NASA NTRS1950

Large-Scale Flight Measurements of Zero-Lift Drag at Mach Numbers from 0.90 to 1.95 of 1/14-Scale Model of the Northrop MX-775B Pilotless Aircraft with Small Body

A flight test was made a t high subsonic, transonic, and supersonic speeds and at high Reynolds numbers to determine the zero-lift drag of a 1/14-scale model of the Northrop MX-775B pilotless aircraft with small small body. The triangular wing of the model had 67.5 deg leading-edge sweep and 15 deg. trailing-edge sweep, The wing airfoil sections were modified NACA 0004 sections. The drag coefficient based on total wing area was 0.0107 at Mach number 1.60. At transonic speeds the maximum drag coefficient was 0.0125. The force-break Mach number was 0,98.

Gillespie, Warren, Jr.↗

NASA NTRS1948

An Investigation of the Wing and the Wing-Fuselage Combination of a Full-Scale Model of the Republic XP-91 Airplane in the Ames 40-by 80-Foot Wing Tunnel

Wind-tunnel tests of a full-scale model of the Republic XP-91 airplane were conducted to determine the longitudinal and lateral characteristics of the wing alone and the wing-fuselage combination, the characteristics of the aileron, and the damping in roll af the wing alone. Various high-lift devices were investigated including trailing-edge split flaps and partial- and full-span leading-edge slats and Krueger-type nose flaps. Results of this investigation showed that a very significant gain in maximum lift could be achieved through use of the proper leading-edge device, The maximum lift coefficient of the model with split flaps and the original partial-span straight slats was only 1.2; whereas a value of approximately 1.8 was obtained by drooping the slat and extending it full span, Improvement in maximum lift of approximately the same amount resulted when a full-span nose flap was substituted for the original partial-span slat.

Hunton, Lynn W.↗

NASA NTRS1949

Tests of a Full-Scale Model of the Republic XF-91 Airplane in the Ames 40- by 80-Foot Wind Tunnel. Force and Moment Data

Wind-tunnel tests of a full-scale model of the Republic XF-91 airplane having swept-back wings and a vee tail were conducted to determine both the stability and control characteristics of the model longitudinally, laterally, and directionally. Configurations of the model were investigated involving such variables as external fuel tanks, a landing gear, trailing-edge flaps, leading-edge slats, and a range of wing incidences and tail incidences.

Hunten, Lynn W.↗