Search NASA⌕ Search

SEARCH · Search NASA

Results for “UO2”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Proton irradiation-induced blistering in UO2

Abstract Proton (H + ) irradiation effects in polycrystalline UO 2 have been studied. The irradiation was carried out using three ion energies and two different ion fluxes at 600 °C. Scanning electron microscopy (SEM) investigations showed that significant surface flaking took place. Focused ion beam (FIB) milling in SEM was successfully applied for extracting lamellas from uneven blistered surfaces for transmission electron microscopy (TEM) investigations allowing detailed investigations for the degradation mechanisms. High-resolution TEM for the flaked UO 2 surfaces revealed that the implanted H + formed sharp two-dimensional cavities at the peak ion-stopping region instead of diffusing to the matrix. The resulting lateral stress likely caused UO 2 surface deterioration in good agreement with previous blistering and flaking studies on crystalline materials. Graphical abstract

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

UFCC Calibration Measurements for UO2 Samples

The uranium UF 6 coincidence counter (UFCC) was designed to measure 5A/B cylinders containing UF6 in the passive neutron self-interrogation mode. The purpose of the present report is to extend the UFCC capability to other sample types such as oxides and liquids that might be found during verification activities. A 252 Cf source was introduced into the detector to make the active mode measurements possible, because only the UF 6 samples have adequate neutron emission for self-interrogation. A customized HDPE insert was designed to position the 252 Cf source under the UO 2 sample cans. The sample enrichments varied from depleted to 93% to establish the shape of the calibration curve and the measurement uncertainties.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Optimization of Conductive Fins to Minimize UO2 Fuel Temperature and Radial Temperature Gradient

To further the development of low-enriched uranium fuels, precedence has been placed on delivering the same amount of power while lowering the fuel temperature and radial temperature gradient. To address this, modeling efforts have resulted in a novel design featuring conductive fins of varying thermal conductivities and geometries inserted into the fuel matrix. These conductive inserts were not allowed to exceed 6% of the original fuel volume. This constraint was imposed due to other designs displacing 10% of fuel volume. A parametric study was performed that consisted of 2.56 million BISON simulations involving varying fin characteristics (i.e., fin thermal conductivity, number, and geometry) to determine the optimal geometric configuration for a desired amount of fuel volume displaced. The results from this study show that the thickness and length of each fin affect the fuel temperature and temperature gradient more than varying the number and thermal conductivity of the fins. The parametric study resulted in the development of an optimized combination to produce the lowest peak fuel temperature, lowest radial temperature gradient, and highest temperature reduction for the amount of original fuel volume displaced. The simulations presented in this work will eventually be compared with irradiation experiments of similar fuel designs at Idaho National Laboratory’s Advanced Test Reactor.

Paaren, Kyle M.↗
NASA NTRS1969

UO2 venting and redistribution

Out-of-pile experiment for measuring uranium dioxide fuel redistribution rates, determining vent hole plugging time and thermal cycling

Phillips, W. M.↗
NASA NTRS1971

Molybdenum-UO2 cermet irradiation at 1145 K.

Two molybdenum-uranium dioxide cermet fuel pins with molybdenum clad were fission-heated in a forced-convection helium coolant for sufficient time to achieve 5.3% burnup. The cermet core contained 20 wt % of 93.2% enriched uranium dioxide. The results were as follows: there was no visible change in the appearance of the molybdenum clad during irradiation; the maximum increase in diameter of the fuel pins was 0.8%; there was no migration of uranium dioxide along grain boundaries and no evident interaction between molybdenum and uranium dioxide; and, finally, approximately 12% of the fission gas formed was released from the cermet core into the gas plenum.

Mcdonald, G.↗
NASA NTRS2012

The Manufacture of W-UO2 Fuel Elements for NTP Using the Hot Isostatic Pressing Consolidation Process

NTP is attractive for space exploration because: (1) Higher Isp than traditional chemical rockets (2)Shorter trip times (3) Reduced propellant mass (4) Increased payload. Lack of qualified fuel material is a key risk (cost, schedule, and performance). Development of stable fuel form is a critical path, long lead activity. Goals of this project are: Mature CERMET and Graphite based fuel materials and Develop and demonstrate critical technologies and capabilities.

Broadway, Jeramie↗
NASA NTRS2013

Advances in the Development of a WCl6 CVD System for Coating UO2 Powders with Tungsten

Demonstrated viability and utilization of: a) Fluidized powder bed. b) WCl6 CVD process. c) Coated spherical particles with tungsten. The highly corrosive nature of the WCl6 solid reagent limits material of construction. Indications that identifying optimized process variables with require substantial effort and will likely vary with changes in fuel requirements.

Mireles, Omar R.↗
DOE OSTI2019

Dopant Effects of UO2

Explore the source record for details and available documents.

Widgeon Paisner, Scarlett↗
DOE OSTI2023

Comparison of Measured and Simulated Neutron Counting with 3He Detectors and the Subcritical Water-Moderated UO2 7uPCX Assembly

An experiment designed to compare neutron noise analysis techniques on subcritical assemblies using differing neutron detector designs was developed as a collaborative effort between the Institut de radioprotection et de surete nucleaire (IRSN), Los Alamos (LANL), Lawrence Livermore (LLNL), and Sandia National Laboratories. This experiment has the final goal of characterizing neutron noise analysis accuracy in determining multiplication in light water systems for various neutron detection systems. This experiment utilized the Seven Percent Critical Experiment (7uPCX) facility at Sandia National Laboratories. The 7uPCX is an assembly designed to investigate light water systems with fuel enrichment above 5% and is able to use square or hex grid plates with varying pitches.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Dissolution of Mechanically Mixed UO2-PuO2 and Insoluble Residue Characteristics

During the reprocessing operations of mixed oxide fuel the dissolution step plays a very important role in the attainment of an acceptable plutonium recovery yield. The importance of this step on the overall fuel cycle was recognized by many authors but was especially treated in depth by Lerch [1] and Nicholson [2].

De Regge, P.↗