Search NASA⌕ Search

SEARCH · Search NASA

Results for “VAPOR PHASE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Investigation of Composition Uniformity in Thickness of GaInAsP Layers Grown on InP Substrates by Vapor-Phase Epitaxy

GaInPAs/InP heterostructures grown by metalorganic chemical vapor-phase deposition at a temperature of 600°C and pressure of 0.1 bar are investigated. The thicknesses of the grown GaInAsP layers amount to about 1 μm. For Ga{sub 1 –x}In{sub x}P{sub 1 –y}As{sub y} solid solutions with average compositions of x = 0.77–0.87 and y = 0.07–0.42, the variation in the content y of V-group atoms over the epitaxial-layer thickness by a value of Δy up to 0.1 atomic fractions in the sublattice of the V-group elements is revealed by secondary ion mass spectrometry. In most cases, a change in y occurs in the GaInAsP layer over a length to 200 nm from the InP heterointerface. In certain cases, y varies throughout the entire GaInPAs-layer thickness. For the epitaxial layers with satisfactory crystalline perfection, the value of Δy is less in the case of better lattice-matching between the GaInPAs epitaxial layer and the substrate. For GaInPAs layers strongly lattice-mismatched with the substrate and characterized by a low degree of crystalline perfection, the value of Δy is close to zero. All these facts enable us to assume that it is elastic deformations arising in the forming monolayer lattice-mismatched with the growing surface that affect the incorporation of V-group atoms into the forming crystalline lattice.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Halide Vapor Phase Epitaxy of Ge from an Elemental Source

Halide vapor phase epitaxy shows promise for low-cost photovoltaic device manufacturing because of its high growth rates and lower cost elemental precursors but previously has not been used to deposit epitaxial Ge. Here, we demonstrate Ge deposition by generating GeCl 2 in situ from solid Ge and HCl in a N 2 ambient. To achieve Ge growth, we inject AsH 3 and PH 3 as sources of active hydrogen to the growth surface to create a driving force for growth. We do not observe Ge growth unless a supply of hydrogen is added, consistent with thermodynamic calculations. Furthermore, we show the hydrogen source must crack readily on the substrate surface to enable growth; relatively stable sources such as H 2 do not cause growth. Unintentional group V doping is one drawback of using AsH 3 and PH 3 to drive the Ge reaction. We observed As or P concentrations in the Ge films ranging from 4 x 10 17 to 1 x 10 18 atoms/cm 3 , concentrations that can drastically influence device characteristics. However, we note there are numerous other "helper molecule" options that can provide active hydrogen without doping or etching the material. This work provides a path forward for Ge deposition for optoelectronic devices from an elemental source.

14 SOLAR ENERGY↗

Temperature and Density on the Forsterite Liquid‐Vapor Phase Boundary

Abstract The physical processes during planet formation span a large range of pressures and temperatures. Giant impacts, such as the one that formed the Moon, achieve peak pressures of 100s of GPa. The peak shock states generate sufficient entropy such that subsequent decompression to low pressures intersects the liquid‐vapor phase boundary. The entire shock‐and‐release thermodynamic path must be calculated accurately in order to predict the post‐impact structures of planetary bodies. Forsterite (Mg 2 SiO 4 ) is a commonly used mineral to represent the mantles of differentiated bodies in hydrocode models of planetary collisions. Here, we performed shock experiments on the Sandia Z Machine to obtain the density and temperature of the liquid branch of the liquid‐vapor phase boundary of forsterite. This work is combined with previous work constraining pressure, density, temperature, and entropy of the forsterite principal Hugoniot. We find that the vapor curves in previous forsterite equation of state models used in giant impacts vary substantially from our experimental results, and we compare our results to a recently updated equation of state. We have also found that due to under‐predicted entropy production on the principal Hugoniot and elevated temperatures of the liquid vapor phase boundary of these past models, past impact studies may have underestimated vapor production. Furthermore, our results provide experimental support to the idea that giant impacts can transform much of the mantles of rocky planets into supercritical fluids.

58 GEOSCIENCES↗

Vapor phase transport systems for depositing perovskite semiconductors

Vapor phase transport systems and methods of depositing perovskite films are described. In an embodiment, a deposition method includes feeding a perovskite solution or constituent powder to a vaporizer, followed by vaporization and depositing the constituent vapor as a perovskite film. In an embodiment, a deposition system and method includes vaporizing different perovskite precursors in different vaporization zones at different temperatures, followed by mixing the vaporized precursors to form a constituent vapor, and depositing the constituent vapor as a perovskite film.

Bush, Kevin Alexander↗

Control of CuPt Ordering in GaInP Grown by Hydride Vapor Phase Epitaxy

We investigate the degree of ordering present in GaInP layers grown by dynamic hydride vapor phase epitaxy (D-HVPE) as a function of various growth conditions. We assess order parameter from both transmission electron and x-ray diffraction and compare these trends to the order parameter estimated by the photoluminescence-determined band gap in the GaInP layers. The degree of ordering increases with deposition temperature and the ratio of gas-phase group V to group III precursors in the reactor. We also investigate the effect of growth rate, demonstrating the capability of HVPE to suppress order through rapid growth rates. Such ordering dependences are consistent with mechanisms established for ordering observed in GaInP grown by organometallic vapor phase epitaxy (OMVPE), but with weaker ordering than GaInP grown by that method.

growth↗

Insights into the Oxidant/Polymer Interfacial Growth of Vapor Phase Polymerized PEDOT Thin Films

Abstract The vapor phase polymerization (VPP) technique is used to produce thin films of poly(3,4‐ethylenedioxythiopene) (PEDOT) in which the Fe(III)Tosylate oxidant is altered. The oxidant is changed with the addition of an amphiphilic co‐polymer having different molecular weights, namely 2800 Da. and 5800 Da. Resulting PEDOT films produce conductivities of ≈1500 and ≈3000 S cm −1 respectively. Small angle X‐ray diffraction (SA‐XRD) indicates that the oxidant incorporating the larger molecular weight co‐polymer possesses ordered structure and that this in turn helps “template” the PEDOT during film formation. The structure and composition of the bottom (i.e. initial film formation) and top (i.e. final film formation) PEDOT surfaces are studied using surface sensitive analytical techniques; small angle X‐ray diffraction (SA‐XRD), ultraviolet photoelectron spectroscopy (UPS), 2D grazing incidence X‐ray diffraction (2D‐GIXD), metastable induced electron spectroscopy (MIES) and neutral impact collision ion scattering spectroscopy (NICISS). The results indicate that the increase in conductivity using the larger molecular weight co‐polymer additive is due to the film having larger lamella‐ and π‐stacking regions in addition to doping levels which remain unchanged throughout film formation. These conclusions are further supported by results obtained on a model PEDOT:Tosylate system using density functional theory (DFT) calculations.

Sharma, Anirudh↗

Vapor phase elemental sulfur amendment for sequestering mercury in contaminated soil

The process of treating elemental mercury within the soil is provided by introducing into the soil a heated vapor phase of elemental sulfur. As the vapor phase of elemental sulfur cools, sulfur is precipitated within the soil and then reacts with any elemental mercury thereby producing a reaction product that is less hazardous than elemental mercury.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Thermodynamic Properties of Nitrogen Including Liquid and Vapor Phases from 63K to 2000K with Pressures to 10,000 Bar

Tables of thermodynamic properties of nitrogen are presented for the liquid and vapor phases for temperatures from the freezing line to 2000K and pressures to 10,000 bar. The tables include values of density, internal energy, enthalpy, entropy, isochoric heat capacity, isobaric heat capacity velocity of sound, the isotherm derivative, and the isochor derivative. The thermodynamic property tables are based on an equation of state, P=P (p,T), which accurately represents liquid and gaseous nitrogen for the range of pressures and temperatures covered by the tables. Comparisons of property values calculated from the equation of state with measured values for P-p-T, heat capacity, enthalpy, latent heat, and velocity of sound are included to illustrate the agreement between the experimental data and the tables of properties presented here. The coefficients of the equation of state were determined by a weighted least squares fit to selected P-p-T data and, simultaneously, to isochoric heat capacity data determined by corresponding states analysis from oxygen data, and to data which define the phase equilibrium criteria for the saturated liquid and the saturated vapor. The vapor pressure equation, melting curve equation, and an equation to represent the ideal gas heat capacity are also presented. Estimates of the accuracy of the equation of state, the vapor pressure equation, and the ideal gas heat capacity equation are given. The equation of state, derivatives of the equation, and the integral functions for calculating derived thermodynamic properties are included.

Thermodynamic properties↗

Vapor-phase grafting of a model aminosilane compound to Al 2 O 3 , ZnO, and TiO 2 surfaces prepared by atomic layer deposition

Atomic layer deposition (ALD) is a highly versatile surface functionalization technique that can conformally coat both planar and porous substrates. Here we use ALD metal oxide layers to establish a well-defined starting surface for vapor-phase surface organic modification. Vapor-phase (3-aminopropyl)triethoxysilane (APTES) surface silanization of ALD Al 2 O 3 , ZnO and TiO 2 surfaces were studied at 100 °C, 150 °C and 200 °C. In situ quartz crystal microbalance (QCM) and Fourier-transform infrared (FTIR) spectroscopy measurements, and ex situ atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS) measurements showed uniform monolayer silane formation through self-limiting APTES reaction. We observed a higher surface density of grafted APTES species following silanization at 100 °C compared to 200 °C, and we attribute this to the temperature-dependent reactivity of the surface hydroxyls and changes in the mode of APTES reaction. The FTIR and XPS measurements revealed that APTES reacts with Al 2 O 3 and ZnO exclusively through metal siloxy bond formation. However, APTES reacts with TiO 2 through both siloxy bond formation and ammonium salt formation via the amine group.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Planarization of Rough (100) GaAs Substrates via Growth by Hydride Vapor Phase Epitaxy

Wafer reuse techniques help offset the cost of III-V growth substrates by using a single wafer for multiple growths, but costly re-polishing after device removal limits the end benefit. In this work, we present planarization growth by hydride vapor-phase epitaxy (HVPE), a potentially low-cost growth technique, as a method of smoothing rough substrates for subsequent high-quality device growth without the need for polishing. First, we show there is a threshold for allowable substrate roughness without device degradation by comparing devices grown by organometallic vapor-phase epitaxy (OMVPE) on epi-ready polished and pre-polished substrates that did not have the final epi-ready polish. We then demonstrate successful smoothing with HVPE growth on substrates with different surface morphologies, with features ranging from general roughness to large facets. Initial devices grown by HVPE on a pre-polished substate showed no degradation compared to a control wafer, indicating that planarizing rough substrates through HVPE growth is a promising path toward being able to use rough substrates directly for growth, without costly polishing steps.

GaAs↗

Modeling of Gallium Nitride Hydride Vapor Phase Epitaxy

A reactor model for the hydride vapor phase epitaxy of GaN is presented. The governing flow, energy, and species conservation equations are solved in two dimensions to examine the growth characteristics as a function of process variables and reactor geometry. The growth rate varies with GaCl composition but independent of NH3 and H2 flow rates. A change in carrier gas for Ga source from H2 to N2 affects the growth rate and uniformity for a fixed reactor configuration. The model predictions are in general agreement with observed experimental behavior.

Meyyappan, Meyya↗

Optical properties of C-doped bulk GaN wafers grown by halide vapor phase epitaxy

Freestanding bulk C-doped GaN wafers grown by halide vapor phase epitaxy are studied by optical spectroscopy and electron microscopy. Significant changes of the near band gap (NBG) emission as well as an enhancement of yellow luminescence have been found with increasing C doping from 5 × 10{sup 16} cm{sup −3} to 6 × 10{sup 17} cm{sup −3}. Cathodoluminescence mapping reveals hexagonal domain structures (pits) with high oxygen concentrations formed during the growth. NBG emission within the pits even at high C concentration is dominated by a rather broad line at ∼3.47 eV typical for n-type GaN. In the area without pits, quenching of the donor bound exciton (DBE) spectrum at moderate C doping levels of 1–2 × 10{sup 17} cm{sup −3} is observed along with the appearance of two acceptor bound exciton lines typical for Mg-doped GaN. The DBE ionization due to local electric fields in compensated GaN may explain the transformation of the NBG emission.

36 MATERIALS SCIENCE↗

Integrated hydropyrolysis and vapor-phase hydrodeoxygenation process with Pd/Al 2 O 3 for production of advanced oxygen-containing biofuels from cellulosic wastes

This study focuses on developing advanced oxygen-containing biofuels with high furan, cyclic ketone, and ethanol content from holocellulose and cellulosic wastes. To achieve this, we employed an integrated process that combined hydropyrolysis and vapor-phase hydrodeoxygenation using Pd/Al 2 O 3 as a catalyst. In the first stage, the non-catalytic hydropyrolysis of hemicellulose resulted in furfural and acetic acid fractions that were effectively converted into furans, cyclic ketones, and ethanol in the second-stage reactor over Pd/Al 2 O 3 under 0.3 MPa H 2 . We found that a hydropyrolysis temperature of 440 °C in the first stage reactor resulted in the highest yield of oxygen-containing biofuels (171.1 mg/g) with 89.2% hemicellulose conversion. However, increasing the hydrodeoxygenation temperature in the second stage reactor reduced the yield of oxygen-containing biofuels, and at 400 °C, excess deoxygenation led to hydrocarbon production. The Pd/Al 2 O 3 catalyst demonstrated high stability during the vapor-phase hydrodeoxygenation of primary furfural and acetic acid intermediates, with only 2.1% coke formation after three reaction cycles. This scalable process enables the conversion of various cellulosic wastes into advanced oxygen-containing biofuels, with considerable total yields. Our findings suggest that this integrated process holds great promise for converting biomass waste into advanced oxygen-containing biofuels.

09 BIOMASS FUELS↗

A semi-empirical model for the complete orientation dependence of the growth rate for vapor phase epitaxy - Chloride VPE of GaAs

A semi-empirical model has been developed to determine the complete crystallographic orientation dependence of the growth rate for vapor phase epitaxy (VPE). Previous researchers have been able to determine this dependence for a limited range of orientations; however, our model yields relative growth rate information for any orientation. This model for diamond and zincblende structure materials is based on experimental growth rate data, gas phase diffusion, and surface reactions. Data for GaAs chloride VPE is used to illustrate the model. The resulting growth rate polar diagrams are used in conjunction with Wulff constructions to simulate epitaxial layer shapes as grown on patterned substrates. In general, this model can be applied to a variety of materials and vapor phase epitaxy systems.

Seidel-Salinas, L. K.↗

GaAs Solar Cells Grown by Hydride Vapor-Phase Epitaxy and the Development of GaInP Cladding Layers

The high cost of high-efficiency III-V photovoltaic devices currently limits them to niche markets. Hydride vapor-phase epitaxy (HVPE) growth of III-V materials recently reemerged as a low-cost, high-throughput alternative to conventional metal- organic vapor-phase epitaxy (MOVPE) growth of high-efficiency solar cells. Previously, we demonstrated unpassivated HVPEgrown GaAs p-n junctions with good quantum efficiency and high open-circuit voltage (Voc). In this work, we demonstrate the growth of GaInPby HVPE for use as a high-quality surface passivation layer to GaAs solar cells. Solar cells grown with GaInP window layers show significantly improved quantum efficiency compared with unpassivated cells, increasing the short-circuit current (JSC) of these low-cost devices. These results show the potential of low-cost HVPE for the growth of high-quality III-V devices.

14 SOLAR ENERGY↗

Vapor-Phase Aggregation of Cerium Oxide Nanoparticles in a Rapidly Cooling Plasma

Local conditions, such as temperature and oxygen availability, have a pronounced effect on the formation and evolution of fallout following a nuclear explosion. While the behavior of nuclear-relevant materials such as uranium has begun to be explored under a wider range of environments, little is known about the behavior of plutonium. Here, using cerium as a surrogate, we track the vapor-phase aggregation of cerium oxide nanoparticles created in a plasma flow reactor under conditions of controlled temperature at two different oxygen fugacities. In situ optical emission spectroscopy is used to measure the variations in the spectral intensity of atomic and molecular species with temperature and oxygen content. We find that the relative rate of gas-phase oxidation of cerium is highly dependent on both temperature and local redox conditions within the flow reactor, to the extent that doubling the oxygen availability effectively doubles the amount of vapor-phase cerium monoxide at high temperatures (>2000 K). Condensed cerium oxide nanoparticles are also collected and analyzed ex situ via transmission electron microscopy and grazing-incidence small-angle X-ray scattering to determine their elemental composition, crystal structure, and size distribution. The size and morphology of the condensed nanoparticles are independent of local redox conditions, forming the same crystal type with the same size distribution regardless of oxygen availability. Postcondensation particle evolution, however, is found to be predominantly driven by temperature, with the average particle size increasing as particles cool and subsequently aggregate. These results expand our understanding of the chemical and physical behavior of refractory oxides that form during the early stages of fallout formation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effects of Water Vapor on the Reactivity of Aluminosilicates in Vapor-Phase Propanal Aldol Condensation

Aluminosilicate materials have been extensively studied as efficient aldol catalysts for C-C coupling reactions due to their acidic nature, high surface area, thermal stability, and porous structure. This work investigated the impact of water vapor pressure on the catalytic reactivity of aluminosilicates for the aldol condensation of propanal to 2-methyl-2-pentenal (MP). The catalytic performance of amorphous SiO2-Al2O3 (A-Si-Al) and aluminated MCM-41 (Al-MCM-41) for the vapor-phase aldol condensation of propanal was evaluated at 200 degrees C as a function of vapor-phase water content at atmospheric pressure. Our findings demonstrate that co-feeding low water vapor pressures (1-18 kPa) with propanal enhances the rates of MP production at 200 degrees C on A-Si-Al. Conversely, water vapor pressures of 25 kPa result in a decrease in aldol dimer formation rates. The rate of MP production evaluated on Al-MCM-41 also increased in the presence of 5 kPa water compared to anhydrous conditions. Propylamine temperature-programmed desorption analyses revealed an increase in Bronsted acid site density when both catalysts were exposed to water, which likely accounts for the observed enhancement in aldol condensation reactivity under hydrous conditions. Reversibility testing of the water vapor effect under reaction conditions, combined with X-ray diffraction analysis of fresh, spent, and regenerated catalysts, revealed no structural changes in either aluminosilicate upon exposure to water or reaction conditions. The rates of aldol condensation and the impact of water vapor were highly consistent across both materials, suggesting that zeolite crystallinity has minimal influence on the catalytic performance.

acid catalysts↗