SEARCH · Search NASA

Results for “WINGS - ASPECT RATIO, SMALL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS2013

Revolutionary Aeropropulsion Concept for Sustainable Aviation: Turboelectric Distributed Propulsion

In response to growing aviation demands and concerns about the environment and energy usage, a team at NASA proposed and examined a revolutionary aeropropulsion concept, a turboelectric distributed propulsion system, which employs multiple electric motor-driven propulsors that are distributed on a large transport vehicle. The power to drive these electric propulsors is generated by separately located gas-turbine-driven electric generators on the airframe. This arrangement enables the use of many small-distributed propulsors, allowing a very high effective bypass ratio, while retaining the superior efficiency of large core engines, which are physically separated but connected to the propulsors through electric power lines. Because of the physical separation of propulsors from power generating devices, a new class of vehicles with unprecedented performance employing such revolutionary propulsion system is possible in vehicle design. One such vehicle currently being investigated by NASA is called the "N3-X" that uses a hybrid-wing-body for an airframe and superconducting generators, motors, and transmission lines for its propulsion system. On the N3-X these new degrees of design freedom are used (1) to place two large turboshaft engines driving generators in freestream conditions to minimize total pressure losses and (2) to embed a broad continuous array of 14 motor-driven fans on the upper surface of the aircraft near the trailing edge of the hybrid-wing-body airframe to maximize propulsive efficiency by ingesting thick airframe boundary layer flow. Through a system analysis in engine cycle and weight estimation, it was determined that the N3-X would be able to achieve a reduction of 70% or 72% (depending on the cooling system) in energy usage relative to the reference aircraft, a Boeing 777-200LR. Since the high-power electric system is used in its propulsion system, a study of the electric power distribution system was performed to identify critical dynamic and safety issues. This paper presents some of the features and issues associated with the turboelectric distributed propulsion system and summarizes the recent study results, including the high electric power distribution, in the analysis of the N3-X vehicle.

Kim, Hyun Dae↗

NASA NTRS1954

Analytical study of blockage- and lift-interference corrections for slotted tunnels obtained by the substitution of an equivalent homogeneous boundary for the discrete slots

The solid-blockage interference for a doublet on the tunnel axis and the boundary interference for lifting wings in circular, rectangular, and two-dimensional slotted tunnels have been calculated by substituting an equivalent homogeneous boundary for the physical boundary of discrete slots. In the case of small wings, the interference calculated with the assumption of homogeneity has been found to be consistent with that calculated for the discrete slots for as few as four slots in a circular tunnel. Furthermore, available experimental results for blockage interference are consistent with the results of the present analysis. As a consequence of the assumption of homogeneity it is possible to express the interference of multislotted tunnels as a function of a single parameter which combines the effects of two physical variables: the ratio of open to total slotted wall perimeter and the number of slots. A curve is presented which permits the rapid evaluation of this parameter and numerical results for lift and blockage interference are plotted against the parameter.

Davis, Don D , Jr↗

NASA NTRS1988

Mach number effects on transonic aeroelastic forces and flutter characteristics

Transonic aeroelastic stability analysis and flutter calculations are presented for a generic transport-type wing based on the use of the CAP-TSD (Computational Aeroelasticity Program - Transonic Small Disturbance) finite-difference code. The CAP-TSD code was recently developed for transonic unsteady aerodynamic and aeroelastic analysis of complete aircraft configurations. A binary aeroelastic system consisting of simple bending and torsion modes was used to study aeroelastic behavior at transonic speeds. Generalized aerodynamic forces are presented for a wide range of Mach number and reduced frequency. Aeroelastic characteristics are presented for variations in freestream Mach number, mass ratio, and bending-torsion frequency ratio. Flutter boundaries are presented which have two transonic dips in flutter speed. The first dip is the usual transonic dip involving a bending-dominated flutter mode. The second dip is characterized by a single degree-of-freedom torsion oscillation. These aeroelastic results are physically interpreted and shown to be related to the steady state shock location and changes in generalized aerodynamic forces due to freestream Mach number.

Mohr, Ross W.↗

NASA NTRS1988

Mach number effects on transonic aeroelastic forces and flutter characteristics

Mohr, Ross W.↗

NASA NTRS2003

Numerical Simulations of the Steady and Unsteady Aerodynamic Characteristics of a Circulation Control Wing Airfoil

The aerodynamic characteristics of a Circulation Control Wing (CCW) airfoil have been numerically investigated, and comparisons with experimental data have been made. The configuration chosen was a supercritical airfoil with a 30 degree dual-radius CCW flap. Steady and pulsed jet calculations were performed. It was found that the use of steady jets, even at very small mass flow rates, yielded a lift coefficient that is comparable or superior to conventional high-lift systems. The attached flow over the flap also gave rise to lower drag coefficients, and high L/D ratios. Pulsed jets with a 50% duty cycle were also studied. It was found that they were effective in generating lift at lower reduced mass flow rates compared to a steady jet, provided the pulse frequency was sufficiently high. This benefit was attributable to the fact that the momentum coefficient of the pulsed jet, during the portions of the cycle when the jet was on, was typically twice as much as that of a steady jet.

Liu, Yi↗

NASA NTRS1949

Systematic Investigations of the Effects of Plan Form and Gap between the Fixed Surface and Control Surface on Simple Flapped Wings

Four component measurements of 12 wings of symmetric profile having flaps with chord ratios t(sub R)/t(sub L) = 0.3 and t(sub R)/t(sub L) = 0.2 are treated in this report. As a result of the investigations, the effects of plan form and gap between fixed surface and control surface have been clarified. Lift, drag, pitching moment, and hinge moment were measured in the control-surface deflection range: -23 deg < or = beta < or = 23 deg and the range of angle of attack: -20 deg < or = alpha < or = 20 deg. Six wings with flaps of small chord (t(sub R)/t(sub L) < 0.1) were investigated at large flap settings.

Goethert↗

NASA NTRS2007

Stability Analysis of the Slowed-Rotor Compound Helicopter Configuration

The stability and control of rotors at high advance ratio are considered. Teetering, articulated, gimbaled, and rigid hub types are considered for a compound helicopter (rotor and fixed wing). Stability predictions obtained using an analytical rigid flapping blade analysis, a rigid blade CAMRAD II model, and an elastic blade CAMRAD II model are compared. For the flapping blade analysis, the teetering rotor is the most stable, showing no instabilities up to an advance ratio of 3 and a Lock number of 18. A notional elastic blade model of a teetering rotor is unstable at an advance ratio of 1.5, independent of pitch frequency. Analysis of the trim controls and blade flapping shows that for small positive collective pitch, trim can be maintained without excessive control input or flapping angles.

Floros, Matthew W.↗

NASA NTRS1985

Optimum configuration of high-lift aeromaneuvering orbital transfer vehicles in viscous flow

The results of an analysis to determine the geometrical configuration of an aeroassisted transfer vehicle with a high lift-to-drag ratio (L/D) are described and the constraints imposed on this type of entry vehicle are considered. The aerodynamic characteristics of three configurations, a flat-plate delta wing, a truncated straight cone, and a truncated bent biconic are compared. The effect of viscosity is included in the analysis which examines the rounding of the sharp leading edges. It is shown that, under the constraints of carrying a given volume in the dead air region, the values of L/D are similar for each configuration and that a small blunt leading edge only slightly affects each vehicle's aerodynamic performance, causing less than a 5 percent drop in L/D. The truncated bent biconic is found to be the only configuration that provides the necessary stabilizing moments.

Davies, C. B.↗

NASA NTRS1983

Interference effects of aft reaction-control yaw jets on the aerodynamic characteristics of a space shuttle orbiter model at supersonic speeds

A wind tunnel investigation of the interference effects of aft reaction control system yaw jet plumes on a 0.0125 scale Space Shuttle orbiter model was conducted at Mach numbers from 2.50 to 4.50. Test variables included model angle of attack, model angle of sideslip, jet to free stream mass flow ratio, and number and position of operating jets. The aft reaction control jet plume creates a blockage above and behind the wing on the side in which the jet exhausts and results in flow separation on the wing upper surface and fuselage side. Positive pitching moment and side force increments and negative yawing moment and rolling moment increments due to the flow separations are incurred for left side firing jets, primarily at angles of attack above 10 deg. The yawing moment interference increments are favorable and result in a small jet thrust amplification. As a result of this investigation, the aft reaction control system was certified for operation at supersonic Mach numbers prior to the first flight of the space transportation system (STS-1).

Covell, P. F.↗

NASA NTRS1953

Deflection and Stress Analysis of Thin Solid Wings of Arbitrary Plan Form with Particular Reference to Delta Wings

The structural analysis of arbitrary solid cantilever wings by small-deflection thin-plate theory is reduced to the solution of linear ordinary differential equations by the assumption that the chordwise deflections at any spanwise station may be expressed in the form of a power series in which the coefficients are functions of the spanwise coordinate. If the series is limited to the first two and three terms (that is, if linear and parabolic chordwise deflections, respectively, are assumed), the differential equations for the coefficients are solved exactly for uniformly loaded solid delta wings of constant thickness ratio. For cases for which exact solutions to the differential equations cannot be obtained, a numerical procedure is derived. Experimental deflection and stress data for constant-thickness delta-plate specimens of 45 degree and 60 degree sweep are presented and are found to compare favorably with the present theory.

Stein, Manuel↗

NASA NTRS1960

Performance, Stability, and Control Investigation at Mach Numbers from 0.60 to 1.05 of a Model of the "Swallow" with Outer Wing Panels Swept 75 degree with and without Power Simulations

An investigation of the performance, stability, and control characteristics of a variable-sweep arrow-wing model with the outer wing panels swept 75 deg. has been conducted in the Langley 16-foot transonic tunnel. Four outboard engines located above and below the wing provided propulsive thrust, and, by deflecting in the pitch direction and rotating in the lateral plane, also produced control forces. The engine nacelles incorporated swept lateral and vertical fins for aerodynamic stability and control. Jet-off data were obtained with flow-through nacelles, simulating inlet flow; jet thrust and hot-jet interference effects were obtained with faired-nose nacelles housing hydrogen peroxide gas generators. Six-component force and moment data were obtained at Mach numbers from 0.60 to 1.05 through a range of angles of attack and angles of side-slip. Control characteristics were obtained by deflecting the nacelle-fin combinations as elevators, rudders, and ailerons at several fixed angles for each control. The results indicate that the basic wing-body configuration becomes neutrally stable or unstable at a lift coefficient of 0.15; addition of nacelles with fins delayed instability to a lift coefficient of 0.30. Addition of nacelles to the wing-body configuration increased minimum drag from 0.0058 to 0.0100 at a Mach number of 0.60 and from 0.0080 to 0.0190 at a Mach number of 1.05 with corresponding reductions in maximum lift-drag ratio of 12 percent and 33 percent, respectively. The nacelle-fin combinations were ineffective as longitudinal controls but were adequate as directional and lateral controls. The model with nacelles and fins was directionally and laterally stable; the stability generally increased with increasing lift. Jet interference effects on stability and control characteristics were small but the adverse effects on drag were greater than would be expected for isolated nacelles.

Schmeer, James W.↗

NASA NTRS1955

Low-Lift Drag of the Grumman F9F-9 Airplane as Obtained by a 1/7.5-Scale Rocket-Boosted Model and by Three 1/45.85-Scale Equivalent-Body Models between Mach Numbers of 0.8 and 1.3, TED No. NACA DE 391

Low-lift drag data are presented herein for one 1/7.5-scale rocket-boosted model and three 1/45.85-scale equivalent-body models of the Grumman F9F-9 airplane, The data were obtained over a Reynolds number range of about 5 x 10(exp 6) to 10 x 10(exp 6) based on wing mean aerodynamic chord for the rocket model and total body length for the equivalent-body models. The rocket-boosted model showed a drag rise of about 0,037 (based on included wing area) between the subsonic level and the peak supersonic drag coefficient at the maximum Mach number of this test. The base drag coefficient measured on this model varied from a value of -0,0015 in the subsonic range to a maximum of about 0.0020 at a Mach number of 1.28, Drag coefficients for the equivalent-body models varied from about 0.125 (based on body maximum area) in the subsonic range to about 0.300 at a Mach number of 1.25. Increasing the total fineness ratio by a small amount raised the drag-rise Mach number slightly.

Stevens, Joseph E.↗

NASA NTRS1994

Static investigation of two fluidic thrust-vectoring concepts on a two-dimensional convergent-divergent nozzle

A static investigation was conducted in the static test facility of the Langley 16-Foot Transonic Tunnel of two thrust-vectoring concepts which utilize fluidic mechanisms for deflecting the jet of a two-dimensional convergent-divergent nozzle. One concept involved using the Coanda effect to turn a sheet of injected secondary air along a curved sidewall flap and, through entrainment, draw the primary jet in the same direction to produce yaw thrust vectoring. The other concept involved deflecting the primary jet to produce pitch thrust vectoring by injecting secondary air through a transverse slot in the divergent flap, creating an oblique shock in the divergent channel. Utilizing the Coanda effect to produce yaw thrust vectoring was largely unsuccessful. Small vector angles were produced at low primary nozzle pressure ratios, probably because the momentum of the primary jet was low. Significant pitch thrust vector angles were produced by injecting secondary flow through a slot in the divergent flap. Thrust vector angle decreased with increasing nozzle pressure ratio but moderate levels were maintained at the highest nozzle pressure ratio tested. Thrust performance generally increased at low nozzle pressure ratios and decreased near the design pressure ratio with the addition of secondary flow.

Wing, David J.↗

NASA NTRS2012

Rotary-Wing Relevant Compressor Aero Research and Technology Development Activities at Glenn Research Center

Technical challenges of compressors for future rotorcraft engines are driven by engine-level and component-level requirements. Cycle analyses are used to highlight the engine-level challenges for 3000, 7500, and 12000 SHP-class engines, which include retention of performance and stability margin at low corrected flows, and matching compressor type, axial-flow or centrifugal, to the low corrected flows and high temperatures in the aft stages. At the component level: power-to-weight and efficiency requirements impel designs with lower inherent aerodynamic stability margin; and, optimum engine overall pressure ratios lead to small blade heights and the associated challenges of scale, particularly increased clearance-to-span ratios. The technical challenges associated with the aerodynamics of low corrected flows and stability management impel the compressor aero research and development efforts reviewed herein. These activities include development of simple models for clearance sensitivities to improve cycle calculations, full-annulus, unsteady Navier-Stokes simulations used to elucidate stall, its inception, and the physics of stall control by discrete tip-injection, development of an actuator-duct-based model for rapid simulation of nonaxisymmetric flow fields (e.g., due inlet circumferential distortion), advanced centrifugal compressor stage development and experimentation, and application of stall control in a T700 engine.

Welch, Gerard E.↗

NASA NTRS1974

Small scale wind tunnel model investigation of hybrid high lift systems combining upper surface blowing with the internally blown flap

A small-scale wind tunnel test of a two engine hybrid model with upper surface blowing on a simulated expandable duct internally blown flap was accomplished in a two phase program. The low wing Phase I model utilized 0.126c radius Jacobs/Hurkamp flaps and 0.337c radius Coanda flaps. The high wing Phase II model was utilized for continued studies on the Jacobs/Hurkamp flap. Principal study areas included: basic data both engines operative and with an engine out, control flap utilization, horizontal tail effectiveness, spoiler effectiveness, USB nacelle deflector study and USB/IBF pressure ratio effects.

Waites, W. L.↗

NASA NTRS1959

Wind-Tunnel Investigation of a Small-Scale Sweptback-Wing Jet-Transport Model Equipped with an External-Flow Jet-Augmented Double Slotted Flap

A wind-tunnel investigation at low speeds has been made to study the aerodynamic characteristics of a small-scale sweptback-wing Jet-transport model equipped with an external-flow jet-augmented double slotted flap. Included in the investigation were tests of the wing alone to study the effects of varying the spanwise extent of blowing on the full-span flap. The results indicated that the double-slotted-flap arrangement of the present investigation was more efficient in terms of lift and drag than were the external-flow single-slotted-flap arrangements previously tested and gave a substantial reduction In the thrust-weight ratio required for a given lift coefficient under trimmed drag conditions. An increase in the spanwise extent of blowing on the full-span flap was also found to increase the efficiency of the model in terms of the lift and drag but, as would be expected on a sweptback-wing configuration, was accompanied by significant increases in negative pitching moment.

Johnson, Joseph L., Jr.↗

NASA NTRS1984

Computer studies of hybrid-slotted working sections with minimum interference at subsonic speeds

A series of computations on tunnel boundary-interference effects for hybrid-slotted working sections was performed using the WALINT code. The slots were modeled as lines of porosity with linear crossflow characteristics. The basic shape evaluated was for a rectangular section with height-to-width ratio = 0.835 and its companion in the duplex mode (half model testing) with height-to-width ratio = 0.6. A best overall basic configuration was determined with seven slots on each wall with open area ratio on each wall of 17.5%. For both full-span and half-model testing, the optimum solution required closing all but two slots on each of the half-walls parallel to the plane of the wing (equivalent to four slots on the full floor and ceiling). The results are presented here for the best configurations and are shown to be within the figure-of-merit range of + or - 0.04 in upwash, and + or - 0.1 in curvature for the Mach number range 0.6 to 0.85. Blockage effects are shown to be small.

Steinle, F. W., Jr.↗

NASA NTRS1974

Longitudinal aerodynamic characteristics of an externally blown flap powered lift model with several propulsive system simulators

An investigation of a four-engine externally blown flap (EBF) powered-lift transport was conducted in the Langley V/STOL tunnel to determine the effect of different engine configurations on the longitudinal aerodynamic characteristics. The different engine configurations were simulated by five different sets of propulsion simulators on a single aircraft model. Longitudinal aerodynamic data were obtained for each simulator on each flap deflection corresponding to cruise, take-off, and landing at a range of angles of attack and various thrust coefficients. The bypass ratio (BPR) 6.2 engine simulator provided the best lift and drag characteristics of the five simulators tested in the take-off and landing configurations. The poor performance of the BPR 10.0 and 3.2 engine simulators can be attributed to a mismatch of engine-model sizes or poor engine location and orientation. Isolated engine wake surveys indicated that a reasonable assessment of the aerodynamic characteristics of an engine-wing-flap configuration could be made if qualitative information were available which defined the engine wake characteristics. All configurations could be trimmed easily with relatively small horizontal-tail incidence angles; however, the take-off landing configurations required a high-lift tail.

Hoad, D. R.↗