Search NASA⌕ Search

SEARCH · Search NASA

Results for “Welding Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Thermal Recovery of Plastic Deformation in Dissimilar Metal Weld

Stainless steel has been widely used in challenging environments typical to nuclear power plant structures, due its excellent corrosion resistance. Nickel filler metals containing high chromium concentration, including Alloy 82/182, are used for joining stainless steel to carbon steel components to achieve similar high resistance to stress corrosion cracking. However, the joint usually experience weld metal stress corrosion cracking (SCC), which affects the safety and structural integrity of light water nuclear reactor systems. A primary driving force for SCC is the high tensile residual stress in these welds. Due to large dimension of pressure vessel and limitations in the field, non-destructive residual stress measurement is difficult. As a result, finite element modeling has been the de facto method to evaluate the weld residual stresses. Recent studies on this subject from researchers worldwide report different residual stress value in the weldments [5]. The discrepancy is due to the fact that most of investigations ignore or underestimate the thermal recovery in the heat-affect zone or reheated region in the weld. In this paper, the effect of heat treatment on thermal recovery and microhardness is investigated for materials used in dissimilar metal joint. It is found that high equivalent plastic strains are predominately accumulated in the buttering layer, the root pass, and the heat affected zone, which experience multiple welding thermal cycles. The final cap passes, experiencing only one or two welding thermal cycles, exhibit less plastic strain accumulation. Moreover, the experimental residual plastic strains are compared with those predicted using an existing weld thermo-mechanical model with two different strain hardening rules. The importance of considering the dynamic strain hardening recovery due to high temperature exposure in welding is discussed for the accurate simulation of weld residual stresses and plastic strains. In conclsuion, the experimental result reveals that the typical post-buttering heat treatment for residual stress relief may not be adequate to completely eliminate the residual plastic strains in the buttering layer.

36 MATERIALS SCIENCE↗

Simulation of Multipaction in LB650 Cavity with Weld Profile

This study aims to simulate multipaction in LB650 cavity with weld profile, a first step to replicating an actual cavity, whereas past studies have ignored the same. We attempt to align the simulation data with the experimental data and report the subsequent findings.

Ninan, Z.↗

Quarterly Management Document – FY20, 1st Quarter, Physics-based Creep Simulations of Thick Section Welds in High Temperature and Pressure Applications

During the first quarter of FY20, efforts focused on calibrating a computational model using experimental data. The experimental creep data obtain from specimens containing weld metal exhibit considerable inherent variability making calibration of the computational difficult and may not result in an accurate model.

36 MATERIALS SCIENCE↗

On the quantitative characterization of weld microstructures

Here, a new technique to quantify grain shape and grain boundary curvature in the fusion zone (FZ) and the heat-effected zone (HAZ) of refractory metals and alloys has been developed. The application of this technique to quantify the effect of welding speed on these microstructural characteristics in simulated molybdenum welds is highlighted in this study. A 50% increase in weld speed more than doubles the fraction of grain segments in the fusion zone with orientations between 00 to 300 to the normal to the welding direction, with a corresponding 50% decrease in the fraction of grain segments oriented along the welding direction. This increase in weld speed also results in a reduction in grain size from approximately 120 µm to 84 µm along the WD at the FZ centerline. Grain boundary curvature is negative near the weld centerline and the edge of the fusion zone, indicating that with increasing distance from the weld centerline, the grain segments progressively rotate towards a direction normal to the welding direction at both locations. Presence of regions with relatively straight grain segments indicated by curvatures close to zero were identified in between the weld centerline and the edge of the FZ at all weld speeds.

36 MATERIALS SCIENCE↗

Numerical Simulation and Experimental Validation of Joint Performance in Aluminum-Steel Lap Welds Formed by Friction Stir Dovetailing

Friction stir dovetailing (FSD) is a new dissimilar material joining process that simultaneously forms a mechanical interlock and metallurgical bond at the dissimilar material interface. This work presents development of a modeling and simulation approach to predict mechanical performance of FSD thick section aluminum to steel joints. A finite element analysis (FEA) was carried out in order to predict the load-carrying capacity and failure location for aluminum thicknesses between 12.7 mm and 50.8 mm with different numbers of dovetails. The numerical results and corresponding experimental investigation are in agreement and suggest that the developed methods can be used effectively for design and analysis of FSD joints using standard FEA tools.

Friction stir dovetailing, Friction stir welding, ↗

Precipitation behavior of the sigma phase with Ni and Mn content variations in superaustenitic stainless steel weld metal

Highlights: • Precipitation behaviors in the superaustenitic stainless steel welds were researched. • The fraction and size of the sigma phases decreased with addition of both Ni and Mn. • The Ni addition induced the increase of Mo content in a sigma phase. • The Mn prevented the Mo increase in the sigma, and consequently the Mo depletion. • Ni addition elevated the Mo activity, which induced clustering of Mo in the sigma. - Abstract: In this study, precipitation behavior of the sigma phase with variations of the Ni and Mn in superaustenitic stainless steel weld metal was evaluated focused on microstructure and thermodynamic analysis. Experiments were conducted with variation of Ni and Mn based on a 23Cr-17Ni-6Mo superaustenitic stainless steel weld. And GTAW welding was performed on the casted specimens for simulating the weld metal. The weld metal consisted of γ-dendrite and an amount of sigma phases at interdendritic boundaries. And the sigma phase fraction showed decreasing behavior inversely according to addition of the Ni and Mn in the weld metal. From the microstructural analysis, the Ni addition induced increase of Mo content in the sigma phase, which caused the Mo depletion zone around the sigma phase. Whereas, the Mn addition induced replacement of Mo in sigma phase by Mn, so that the Mo depletion zone was not formed. Also, from the Thermo-Calc analysis, it was revealed that Ni addition caused increase of Mo activity, which induced Mo clustering in the sigma phase, while the Mn addition showed opposite effect of the Mo activity.

36 MATERIALS SCIENCE↗

Numerical Simulation of Residual Stress for Laser Welding of Ti-6Al-4V Alloy Considering Solid-State Phase Transformation

In the present work, a thermal-metallurgical-mechanical model which considered the influence of phase transformation was used to predict the residual stress field of Ti-6Al-4V after laser welding. In this model, the Johnson–Mehl–Avrami equation was used to predict diffusional solid-state phase transformations: α phase to β phase during heating and β phase to α phase during cooling. The Koistinen–Marburger equation was used to predict diffusionless solid-state phase transformation of β phase to martensite during cooling. The properties of material were obtained using a mixing rule based on the phase fraction and the property of each pure phase. By applying this model, the effect of solid-state phase transformations of Ti-6Al-4V alloy on temperature field and stress field during laser welding was considered in the simulation. In addition, experiments were carried out for comparison, which significantly verified the accuracy of the applied model.

36 MATERIALS SCIENCE↗

Towards real time diagnostics of Hybrid Welding Laser/GMAW

Methods are currently being developed towards a more robust system real time feedback in the high throughput process combining laser welding with gas metal arc welding. A combination of ultrasonic, eddy current, electronic monitoring, and visual techniques are being applied to the welding process. Initial simulation and bench top evaluation of proposed real time techniques on weld samples are presented along with the concepts to apply the techniques concurrently to the weld process. Consideration for the eventual code acceptance of the methods and system are also being researched as a component of this project. The goal is to detect defects or precursors to defects and correct when possible during the weld process.

42 ENGINEERING↗

Multi-Pass Hybrid Laser Arc Welding of Alloy 740H

The presentation reviews the progress made toward reducing the joining time of an advanced nickel-based alloy, Alloy 740H by a factor of two using a novel two step fusion welding approach. In the first step, a high powered laser is used to rapidly join thick weld groove lands (~10-12 mm thick) during a single pass. Hybrid laser arc welding (HLAW) is then used to fill the remaining weld groove and complete the joint. This sequential process also utilizes laser wobble in both steps to reduce welding defects and refine the weld microstructure to obtain improved properties compared to conventional gas tungsten or gas metal arc welds, GTAW and GMAW, respectively. The creep behavior of laser-only thick weld groove land welds and HLAW welds were found to be the same or slightly improved compared to conventional GMAW or GTAW welds in this alloy. Creep tests have been started to verify the long-term creep behavior (~10,000 hrs) of these welds. Modeling results on deep penetration laser welding are presented and the initial simulations of laser welding with laser wobble are shown. The next phase of the project will combine the two processes to make complete welds - deep penetration laser welds of thick weld groove lands followed by rapid filling of the remaining weld groove by HLAW - in thick plates (32 mm thick) Alloy 740H plate and entails development of narrow weld groove welding to further decrease the joining time of this alloy.

36 MATERIALS SCIENCE↗

Nondestructive Evaluation of Stress Corrosion Cracking in a Welded Steel Plate Using Guided Ultrasonic Waves

Stress corrosion cracking (SCC) had occurred in early-generation high-level nuclear waste tanks constructed by welding carbon steel. This paper describes an ultrasonic inspection system and its fundamental ability to detect and quantify the length of SCC on thick welded steel plates. The finite element method (FEM) was applied to simulate the welding process to estimate the welding residual stress field. Growth of stress corrosion cracks is driven by crack stress intensities exceeding the subcritical cracking threshold intensity. The subject plate was experimentally inspected with ultrasonic nondestructive evaluation (NDE) techniques to characterize the extent of SCC. The NDE system uses a piezoelectric transducer to generate guided waves in the thick steel plate, and a scanning laser Doppler vibrometer (SLDV) to measure multidimensional time–space wavefield data over a user-defined scanning area in the plate surface. The measured wavefield data can show wave interactions in a localized area in the plate due to the presence of the discontinuities of the SCC. To generate an inspection image that can precisely show the crack’s location and/or the dimension, the wavefield data are further processed to generate inspection image that maps the entire sample plate so the crack can be clearly identified in the plate while its length can be readily estimated. In conclusion, the ultrasonic test results for crack length agree well with the visually estimated length and are close to that predicted by the FEM for cracks in the weld residual stress field.

36 MATERIALS SCIENCE↗

Thermomechanical Analysis of A-TIG and MP-TIG Welding of 2.25Cr-1Mo Steel Considering Phase Transformation

In the present study, a finite element-based 3D mesh model is used to simulate the effect of welding processes on the temperature distribution, residual stress and distortion in 11-mm-thick 2.25Cr-1Mo steel weld joints. Tungsten inert gas (TIG) and activated-TIG (A-TIG) welding processes were employed for the fabrication of weld joints. Austenite-to-bainite phase transformation is taken into account in the numerical analysis. The heat input fitting tool has been used to calibrate the heat source by matching the simulated weld bead with that of the actual weld bead. Peak temperature was higher at the weld center for A-TIG weld joint, and the weld joint exhibited a sharp temperature gradient at the weld interface. There was good agreement between the predicted and measured thermal cycles. A-TIG and multipass-TIG (MP-TIG) weld joints exhibited similar longitudinal residual stresses in heat affected zone with a difference of 50 MPa. Moreover, A-TIG weld joint fabricated by double-side welding technique employing two passes exhibited reduced distortion than MP-TIG weld joints. A higher magnitude of distortion was in MP-TIG weld joint which was attributed to more weld metal volume caused by more number of weld passes required to fill the V-groove. There was good agreement between the predicted and measured residual stress and distortion values.

36 MATERIALS SCIENCE↗

Fourth-order partial differential equation noise removal on welding images

Partial differential equation (PDE) has become one of the important topics in mathematics and is widely used in various fields. It can be used for image denoising in the image analysis field. In this paper, a fourth-order PDE is discussed and implemented as a denoising method on digital images. The fourth-order PDE is solved computationally using finite difference approach and then implemented on a set of digital radiographic images with welding defects. The performance of the discretized model is evaluated using Peak Signal to Noise Ratio (PSNR). Simulation is carried out on the discretized model on different level of Gaussian noise in order to get the maximum PSNR value. The convergence criteria chosen to determine the number of iterations required is measured based on the highest PSNR value. Results obtained show that the fourth-order PDE model produced promising results as an image denoising tool compared with median filter.

42 ENGINEERING↗

Stress Relaxation Cracking in 347H Stainless Steel Arc Welds: Susceptibility Evaluation of Heat-Affected Zone

Stress relaxation cracking (SRC) is considered one of the major failure mechanisms for 347H stainless steel welds at elevated service temperatures or during post weld heat treatment (PWHT), especially within the heat-affected zone (HAZ). This work focuses on the characterization of SRC susceptibility within 347H physically simulated arc welded HAZ at elevated temperatures. A four-step SRC thermomechanical test in combination with finite element modeling (FEM) of the welding and testing processes is developed to establish a susceptibility map for HAZ. The test first runs a thermal cycle with three different peak temperatures (1335, 1275, and 1150 °C) to duplicate representative HAZ subzone microstructures, followed by time-to-failure examination under a variety of pre-stress (260–600 MPa) and pre-strain conditions (0.03–0.19) as a function of reheat temperatures between 750 and 1050 °C. With the aid of FEM, SRC susceptibility maps are generated to identify the threshold stress, plastic strain, and creep strain as a function of test temperature. It was found out that HAZ subzone with a lower peak temperature (1150 °C) appears to be slightly less susceptible to SRC than the other two subzones that experienced higher peak temperatures. Generally, time-to-fracture reduces with increasing initially applied stress and strain for all test temperatures. The pre-stress thresholds decrease from about 500 to 330 MPa as the testing temperature increases from 800 to 1050 °C, while the corresponding initial plastic strain thresholds reduces from 0.15 to 0.06. The SRC susceptibility was also evaluated through the Larson–Miller Parameter (LMP) analysis as a function of plastic strain, initial stress and starting stress upon reaching the testing temperature, respectively. The 1050 °C test with a high pre-applied strain (0.1) exhibits an extremely short time to failure (t = 3 s) that lies outside the general trend in LMP analysis. Additionally, it was identified that a plastic strain above 0.07 is identified to significantly reduce the bulk creep strain tolerance to fracture and therefore increases SRC susceptibility. Hardness measurement and fractography analysis indicated that the strain aging of niobium carbonitrides and other potential phases in conjunction with intergranular precipitates contributes to an increase in microhardness and increased intergranular cracking susceptibility.

14 SOLAR ENERGY↗

Surface engineering to enhance heat generation and joint strength in dissimilar materials AZ31 and DP590 ultrasonic welding

A multiscale simulation approach was developed and employed to optimize the sheet surface conditions for higher interfacial temperature and joint strength in ultrasonic welding of magnesium alloy AZ31 and dual-phase steel DP590. First, a mesoscale model was used to study the relationship between friction coefficient and surface roughness, which can be modified by various engineering methods. Then a macroscopic process model was employed to study the effects of surface roughness on heat generation, indicating that a temperature increase can be achieved with rougher surfaces on two sides of both DP590 and AZ31 sheets. Samples prepared by sanding and filing, as well as grinding, were first characterized for surface roughness and then welded under ultrasonic vibration. An infrared camera was used to measure temperatures in situ for model validation. Overall, lap shear test results for the welded joint showed that the joint strength can be improved by 10~25% using filing and round grinding methods as a result of the enhanced heat generation and mechanical interlocking on the interface.

42 ENGINEERING↗

Engineering approximations in welding: Bridging the gap between the speculation and simulation

During the course of their careers, welding engineers and welding metallurgists are often confronted with questions regarding welding process and properties that on the surface appear to be simple and direct, but are in fact quite challenging. These questions generally mask an underlying complexity whose underpinnings in scientific and applied research predate even the founding of the American Welding Society, and previous Comfort A. Adams lectures provide ample and fascinating evidence of the breadth and depth of this complexity. Using these studies or their own experiences and investigations as a basis, most welding and materials engineers have developed engineering tools to provide working approaches to these day-to-day questions and problems. In this article several examples of research into developing working approaches to welding problems are presented.

36 MATERIALS SCIENCE↗

Properties of Equivalent Source Distributions Useful for Inverse Thermal Analysis

A general approach for inverse thermal analysis of heat deposition processes is parametric modeling of such processes using effective or equivalent source distributions (ESDs). ESDs can be adjusted conveniently for calculation of temperature fields, which are constrained according to boundary and temperature constraint conditions. This study applies properties of ESDs useful for parametric modeling of heat deposition processes. Inverse thermal analysis of a friction stir weld is presented, which is prototypical of processes tending to be complex with respect to energy deposition morphology. This analysis demonstrates properties of ESDs providing relatively optimal parametric modeling of energy deposition processes.

36 MATERIALS SCIENCE↗