Search NASA⌕ Search

SEARCH · Search NASA

Results for “Window Materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Apollo experience reports: Window contamination

The problem of window contamination in the Apollo command module is reviewed. All five command module windows were contaminated while in earth orbit on the first three manned Apollo flights. The contamination sources were identified and eliminated. Preflight testing of lunar module windows showed that no serious contamination should occur, and this conclusion was verified in subsequent manned flights. The command module window designs and materials are described, the window contamination sources are identified, and the inflight and chemical analyses of the contamination are outlined. The corrective actions that were taken are reviewed. For the lunar module, the window design and materials and the preflight and fight evaluations are described. Window design recommendations are made.

Leger, L. J.↗
NASA NTRS1973

Complex permittivity measurements during high temperature recycling of space shuttle antenna window and dielectric heat shield materials

The research performed and the data obtained on candidate space shuttle antenna window and heat shield materials are presented. The measurement technique employs a free-space focused beam microwave bridge for obtaining RF transmission data, and a device which rotates a sample holder which is heated on one side by natural gas-air flames. The surface temperature of each sample is monitored by IR pyrometry; embedded and rear surface thermocouples are also used in obtaining temperature data. The surface of the sample undergoing test is subjected to approximately the same temperature/time profile that occurs at a proposed antenna position on the space shuttle as it re-enters. The samples are cycled through ten of these temperature profiles to determine the recycling effects. Very little change was noted in the materials due to the recycling.

Bassett, H. L.↗
NASA NTRSDate not supplied

Pressurized Rover Lunar Surface Windows Thermal Trade Study

The pressurized rover (PR) is a habitable lunar vehicle that supports up to two crew members and EVAs. The PR is expected to operate with a crew at the lunar south pole for up to 30 consecutive days. Lunar surface missions represent a significant thermal challenge due in part to the extreme changes in temperature environment. Minimizing heat leaks is essential to be able to survive cold phases of lunar surface missions. Windows in particular can be a significant source of heat leak when designed without thermal performance in mind. In addition, correctly modeling windows, and transparent materials in general, represents a significant thermal challenge. It can also be challenging to obtain accurate radiative properties for modern window materials. This study focuses on the modeling approach, results, and possible window heat leak mitigation techniques for pressurized rover. Mitigation techniques explored in this study include low emissivity coatings and removable internal or external covers. Window layup, geometry, and size are also assessed in this study for their impact to heat leak.

Sydney June Taylor↗
DOE OSTI2026

Examination of Replicate Syntheses of Metal Organic Frameworks as a Window into Reproducibility in Materials Chemistry

Replicate experiments are a useful tool in understanding the repeatability of scientific measurements. In 2019, a systematic search for replicate syntheses of a collection of 130 metal–organic frameworks (MOFs) found that 89% of these materials had no reported replicate syntheses apart from the original publications identifying the material (Agrawal, M. Proc. Natl. Acad. Sci. U.S.A. 2020, 117, 877−88210.1073/pnas.1918484117). A potential weakness of that search was that only 5–11 years had elapsed since the original publication of each material. Here, this analysis is extended to all publications 11–17 years after the original publication. Although this extended time period identifies more repeat syntheses, 83% of the materials still have no reported replicate syntheses. We also consider how appropriately selected Density Functional Theory (DFT) calculations can provide corroboration for the experimentally reported crystal structures. By using data from previous high-throughput DFT studies, corroborating evidence from DFT was available for 17% of the 130 structures for which no replicate syntheses are available. In total, approximately 1/3 of the 130 MOFs have data associated with replicate synthesis experiments and/or directly corroborating DFT calculations.

Sholl, David S. [Oak Ridge National Laboratory (OR↗
NASA NTRS1973

Synthesis of optically clear polymeric materials for high temperature windows

A polymer has been developed that has excellent potential for use as windows in spacecraft as well as conventional aircraft. This polymer, phenolphthalein polycarbonate, has outstanding thermal properties, e.g., in place of melting or burning, it produces an insulating charred foam that closes off transmission of radiant heat through the window. This fact, coupled with an oxygen index of 0.43 and a 177 C tensile strength of 58 mega Newtons/sq m, makes this polymer a prime candidate for further development. Pilot plant preparation in a 20 gallon Pfaudler kettle was accomplished and large test specimens were prepared for evaluations.

Pannell, C. E.↗
DOE OSTI2025

Erosion of high-Z refractory coatings for helicon plasma source window

Proto-MPEX (Materials Plasma Exposure eXperiment), a linear plasma device (LPD), using a high power radio frequency (RF) (⩾100 kW, 13.56 MHz) helicon plasma source, has suffered RF sheath-induced window erosion. The sputtered impurities from the window surface transport toward the downstream target affecting plasma-material interaction studies. The rectified sheath voltage formed was high enough to cause window erosion by light ions due to its low-Z components (e.g. Si 3 N 4 and AlN). Hence, we are proposing impurity mitigation strategies, which involve the application of a Faraday screen to lower the rectified sheath voltage and the application of high-Z refractory coatings on the existing window plasma-facing surface. In this work, we report the erosion of two different coatings, i.e., tantalum oxide (Ta 2 O 5 ) and hafnium oxide (HfO 2 ) on a silicon nitride (Si 3 N 4 ) window material under conditions of low-energy deuterium (D) ion impact, well below the Ta 2 O 5 sputtering energy threshold (i.e. 250 eV). The test samples were RF-biased and exposed to a high D-ion fluence (∼10 26 m −2 ) in Plasma Interaction with Surface Component Experimental Station (PISCES-A) LPD. The experimentally measured sputtering yields of the high-Z refractory coatings below the sputtering energy threshold of Ta 2 O 5 indicate an increased erosion due to the plasma impurities, especially due to oxygen. Improving the vacuum level could reduce the oxygen impurities and increase the lifespan of the coated helicon window for plasma operation. Post-surface analysis indicates no preferential erosion of oxygen or enrichment of the high-Z surface component. This is likely due to an effective energy transfer from the impurity ion for sputtering of the high-Z component in the coating. With the reduced rectified sheath voltage at the window surface and improved vacuum conditions, the proposed high-Z refractory coatings offer a promising solution for reducing window erosion in future MPEX plasma operations at ORNL.

RF bias↗
DOE OSTI2025

Deposit and Evaluate Material Across Extremes of Process Windows

Additive manufacturing (AM) can be a viable pathway to fabricate near-net-shape parts for next generation nuclear reactors. Stainless steel 316H (SS 316H) has been identified as a material of interest in the Advanced Materials and Manufacturing Technologies program to accelerate the use of AM for nuclear energy applications. Heterogeneity in material performance is one of the biggest challenges to qualification of AM SS 316H for in-service applications.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Exploiting Intersubband Plasmons in Vertically Aligned Carbon Nanotubes for Near-Infrared Electrochromic Windows

Optically transparent materials with switchable near-infrared (NIR) transmissivity are of significant interest for energy-saving smart window technologies. To this end, we demonstrate that semitransparent films of vertically aligned carbon nanotubes (CNTs) incorporated into electrochemically gated devices exhibit NIR transmittance changes up to 47% and bistable optical states that are appealing for low-power, large-area operation. The tunable NIR electrochromic response is driven by a doping-induced intersubband plasmon (ISBP) absorption, an optical feature in CNTs that is selective to light polarized perpendicular to the CNT axis. Vertically aligned CNT films (as opposed to more conventional planar CNT mats) thus allow us to isolate and study the ISBP resonance changes with applied voltage, electrode material, and film thickness.

absorption↗
NASA NTRS1994

Coaxial microwave electrothermal thruster performance in hydrogen

The microwave electro thermal thruster (MET) is an electric propulsion concept that offers the promise of high performance combined with a long lifetime. A unique feature of this electric propulsion concept is its ability to create a microwave plasma discharge separated or floating away from any electrodes or enclosing walls. This allows propellant temperatures that are higher than those in resistojets and reduces electrode and wall erosion. It has been demonstrated that microwave energy is coupled into discharges very efficiently at high input power levels. As a result of these advantages, the MET concept has been identified as a future high power electric propulsion possibility. Recently, two additional improvements have been made to the coaxial MET. The first was concerned with improving the microwave matching. Previous experiments were conducted with 10-30 percent reflected power when incident power was in excess of 600 W(exp 6). Power was reflected back to the generator because the impedance of the MET did not match the 50 ohm impedance of the microwave circuit. To solve this problem, a double stub tuning system has been inserted between the MET and the microwave power supply. The addition of the double stub tuners reduces the reflected power below 1 percent. The other improvement has prepared the coaxial MET for hydrogen experiments. To operate with hydrogen, the vacuum window which separates the coaxial line from the discharge chamber has been changed from teflon to boron nitride. All the microwave energy delivered to the plasma discharge passes through this vacuum window. This material change had caused problems in the past because of the increased microwave reflection coefficients associated with the electrical properties of boron nitride. However, by making the boron nitride window electrically one-half of a wavelength long, power reflection in the window has been eliminated. This technical note summarizes the experimental performance of the improved coaxial MET when operating in nitrogen, helium, and hydrogen gases.

Richardson, W.↗
NASA NTRS1975

Optical effect of the contamination of infrared windows by the outgassing of materials in outer space

The composition and evaporation rate of the outgassing of a space vehicle thermal control paint as a function of temperature were studied. A contamination chamber was designed, constructed, and tested. Samples of thermal control paint were tested to determine if heating to moderate temperatures causes them to release outgassing products which can be collected on a cooled cesium iodide window for identification by IR analysis. Results showed that outgassing of surfaces other than the sample was a problem. Spectral bands of the deposits collected were compared.

Silberman, E.↗
NASA NTRS1975

Optical effect of the contamination of infrared windows by the outgassing of materials in outer space

The products and kinetics of outgassing from S13G paint were studied by using infrared absorption measurements of the material outgassed (using an evaporation cell and vacuum chamber). Two separate long-term experimental depositions from heated samples of the S13G paint were made. Before each experiment, the vacuum chamber and sample holder were carefully cleaned and outgassed to ensure that subsequent deposits on the colled-window were due only to the products evaporated from the sample. Results of experiments are listed and discussed.

Silberman, E.↗
NASA NTRS1994

Effect Of Molecular Weight On Adhesive Properties Of The Phenylethynyl-Terminated Polyimide LARC(sup TM)-PETI-5

Future civilian aircraft will require the use of advanced adhesive systems with high temperature capabilities. One such material has been developed at the NASA Langley Research Center, a phenylethynyl-terminated polyimide given the designation LARC(sup TM)-PETI-5. Recent work has shown the advantages of similar phenylethynyl-terminated polyimides as films, moldings, adhesives, and composite matrix resins. Phenylethynyl-terminated oligomers provide greater processing windows than materials which incorporate simple ethynyl endcaps. Since these low molecular weight, low melt viscosity oligomers thermally cure without the evolution of volatile by-products, they provide an excellent means of producing polymers with high glass transition temperatures, excellent solvent resistance, and high mechanical properties. Three different versions of LARC(sup TM)-PETI-5 with theoretical number average molecular weights (M(sub n)s) of 250, 5000, and 10000 g/mol were synthesized in this work. Differential Scanning Calorimetry (DSC) measurements were performed on the dry powder form of these materials to establish cure conditions which result in high glass transition temperatures (T(sub g)s). Lap shear specimens were prepared from adhesive tape made from each material and with the thermal cure conditions determined from the DSC data. The tensile shear data established processing conditions which provided the best adhesive strengths. Further testing was performed to establish the properties of LARC(sup TM)-PETI-5 as an adhesive material and to determine its solvent resistance.

Cano, Roberto J.↗
NASA NTRS1989

A new structure for comparing surface passivation materials of GaAs solar cells

The surface recombination velocity (S sub rec) for bare GaAs is typically as high as 10 to the 6th power to 10 to the 7th power cm/sec, which dramatically lowers the efficiency of GaAs solar cells. Early attempts to circumvent this problem by making an ultra thin junction (xj less than .1 micron) proved unsuccessful when compared to lowering S sub rec by surface passivation. Present day GaAs solar cells use an GaAlAs window layer to passivate the top surface. The advantages of GaAlAs in surface passivation are its high bandgap energy and lattice matching to GaAs. Although GaAlAs is successful in reducing the surface recombination velocity, it has other inherent problems of chemical instability (Al readily oxidizes) and ohmic contact formation. The search for new, more stable window layer materials requires a means to compare their surface passivation ability. Therefore, a device structure is needed to easily test the performance of different passivating candidates. Such a test device is described.

Desalvo, Gregory C.↗
NASA NTRS1993

Surface passivation of InP solar cells with InAlAs layers

The efficiency of indium phosphide solar cells is limited by high values of surface recombination. The effect of a lattice-matched In(0.52)Al(0.48)As window layer material for InP solar cells, using the numerical code PC-1D is investigated. It was found that the use of InAlAs layer significantly enhances the p(+)n cell efficiency, while no appreciable improvement is seen for n(+)p cells. The conduction band energy discontinuity at the heterojunction helps in improving the surface recombination. An optimally designed InP cell efficiency improves from 15.4 percent to 23 percent AMO for a 10 nm thick InAlAs layer. The efficiency improvement reduces with increase in InAlAs layer thickness, due to light absorption in the window layer.

Jain, Raj K.↗
NASA NTRS1970

Thermal performance and radio-frequency transmissivity of candidate ablation materials for S-band antenna window application on manned spacecraft

A test program was conducted in the MSC 1.5 MW arc-heated facility to evaluate the thermal performance of ablation materials having potential application as radio frequency windows. These tests were conducted for the improvement of omnidirectional antenna operating characteristics during atmospheric reentry. Since a full scale model of the Apollo command service module was available for antenna tests, this mockup was used as a basic for the tests. Test models were subjected to heating conditions simulating the nominal lunar return trajectory (AS-501) and the design trajectories, high heat load and high heating rate. RF measurements were made before and after the arc jet tests to measure attenuation effects due to the thermal degradation of the materials under consideration. The test program demonstrated that additional development is required in materials technology to achieve an ablative system with both good RF transmission characteristics and thermal-structural integrity.

Tillian, D. J.↗
NASA NTRS2022

Fracture Mechanics Properties of Fused Silicas Used for International Space Station Windowpanes

The fracture toughness and slow crack growth (SCG) parameters of a quartz-based silica and a high-purity fused silica were measured as part of a program to review the reliability of the International Space Station windows. The materials exhibit the same fracture toughness (.75 MPa m^(1/2) in N2) and very similar SCG parameters. The literature on fused silica indicates excellent agreement of fracture toughness, but a very wide range of SCG parameters, even from the same institution, with strength-based methods usually yielding a lower power law exponent than direct crack velocity measurements. Use of the exponential function is shown to provide better agreement between test methods, with velocity curves derived from strength tests of bare fiber and polished or ground test specimens paralleling those from wide-range, direct crack velocity observations, implying that constant stress rate tests can predict long lifetime via the exponential function. However, much variation still exists. SCG parameters for soda–lime silicate are much less sensitive to the test method than fused silica. Static load tests and stress intensity measurements resulted in a fatigue threshold of .3 MPa m^(1/2) for fused silica.

Silica, toughness, impact, crack growth, windows, ↗