Search NASA⌕ Search

SEARCH · Search NASA

Results for “Wipes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

MODELING OF ENHANCED AIR DEHUMIDIFICATION THROUGH ELECTRICALLY CHARGED VAPOR CAPTURING ELECTROSTATIC DROPLETS

This paper investigated the potential of a new electrostatic-based water vapor separation system for humidity control in buildings. The Electrospray Vortical Flow eXchanger (EVFX) consists of small electrically charged water droplets released inside air vortexes to attract water vapor molecules, effectively wiping out the humidity from the air. Larger droplets are then removed at the outer wall of the vortex. If a water molecule is placed in a gradient electric field, such a polar molecule experiences a dielectrophoresis force, which moves the molecules and produces a vapor concentration gradient. When the vapor density exceeds the saturation level, nucleation occurs. A thermodynamic model that captures this phenomenon was described in this paper. Electrosprayed droplets were initially charged close to their maximum electrical charge dictated by the Rayleigh limit; these droplets were used as nucleation centers. The high electric charge decreased the pressure of the vapor, which was in equilibrium with the droplets. This enhanced the charged droplets' nucleation and growth that depleted the vapor phase near the droplets, which was compensated for by the dielectrophoresis flow and diffusion. Significant water vapor condensation was predicted for small droplets at a high electrical charge. Beyond a specific droplet size, while the condensation of water vapor was still theoretically possible, it was somewhat limited because the further growth of the large charged droplets was inhibited due to their high inherent water vapor pressure near the surface. A case study illustrated the potentials and limitation of the EVFX for droplets charged to the Rayleigh limit, for which the effective range of diameters resulted between 10 nm up to few micron.

Morcelli, Stefano↗
DOE OSTI2022

NUMERICAL INVESTIGATION OF AIR DEHUMIDIFICATION THROUGH WATER DROPLETS DIELECTROPHORESIS

This paper numerically investigated the dehumidification of moist airflow in a converging rectangular duct with electrically enhanced condensation. The aim was to develop a condensation model that predicted water vapor condensation by employing the dielectrophoresis principle. The charged droplets were injected into the computational domain to produce a gradient electric field. The dielectrophoretic interaction between the droplets and vapor molecules of the humid air resulted in local water vapor condensation at the vapor and liquid droplet interface. This phenomenon is described in detail in this paper. A hybrid Eulerian-Lagrangian solver SprayFoam was developed based on OpenFOAM® to simulate condensation in two-phase gas-liquid mixtures. The following developments were made based on the standard compressible multiphase flow solver SprayFoam in OpenFOAM®: (1) Eulerian solver for gas phase (2) multi-component species transport, and (3) Lagrangian solver for gas-droplet two-phase flows and sub-models for liquid droplets. The newly developed numerical model was experimentally validated with data from a series of tests conducted in the authors' laboratory. The results showed that the simulations followed the same trends as the data, and the model predicted the condensation due to the electro-spray injection process in the air stream. The injected water droplets, which are electrically charged to their Rayleigh limits, increased in size while wiping out the humidity from the air. The simulations indicated that the dehumidification was about 1% for 0.5 cubic feet per minute airflow rate. Scaling up to larger flows is a future follow-up work.

Yel Mahi, *Maliha↗
DOE OSTI2021

Laser-Interference Surface Preparation for Enhanced Coating Adhesion and Adhesive Joining of Multi-Materials (Final Project Report)

This report investigates a laser-interference surface treatment as a non-contact, i.e., without major solid/liquid medium application or abrasion, and non-chemical surface preparation method for aerospace coating systems. It was proposed to use the laser-interference technique to structure surfaces of Al and/or Ti, creating "rough" surfaces with pre-engineered series of ridges and valleys at submicron scale. The science goal of this study was to develop an understanding of the surface microstructure, topology, and physical mechanisms that would improve adhesion and corrosion protection of Al2024-T3. Microstructure analysis indicates that the laser-interference structuring (LIS) was found to reduce the formation of CuMn-rich precipitates in Al 2024-T3 over a 500-800 nm depth from top surface. The X-cut and cross-hatch coating adhesion ratings indicate that the LIS specimens meet the performance requirements in the coating adhesion specifications by having a higher or identical ranking to those specimens prepared with current state-of-the-art chemical conversion or sulfuric acid anodizing. After the ASTM B117 corrosion exposure, it was found that the laser processed specimens exhibited only few blisters. It was found that the corrosion damage was minimized at a laser rastering speed of 4 mm/s, for which only 33% of specimens developed very minor corrosion damage. The ASTM D1654 creepage ratings, used to evaluate corrosion damage along the scribe lines, were found to be at least nine for all coated panels. These results indicate that the laser-interference technique with the additional acetone wiping has the potential to be further developed as a minor chemical surface preparation technique for chromate-containing epoxy primers coatings.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Molecular Dynamics of High Pressure Tin Phases I: Strength and deformation evaluations of empirical potentials [Slides]

Multi-phase problems have so many more unknowns, we’d like to have a tool to constrain some open questions related to microstructure and twin & dislocation behavior. We want an atomistic scale perspective on aspects of strength. Some multi-scale questions accessible to atomistic study: What lattice-specific behavior influences dislocation production/mobility and/or twinning? Do the phase transformations wipe-out, modify or preserve grain size and orientation? Does plastic strain reset at phase transition? If so under what conditions? Tin is the material chosen for the effort because it is non-hazardous and has multiple accessible solid phases at relatively low pressures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Biofouling and Corrosion Study for a Novel Linear Guided Wave Energy Converter (Post Access Report)

The overall objective of this project was to examine the reliability and performance of antibiofouling coatings used for a wave energy converter (WEC) developed by E-Wave Technologies. The particular coatings were selected for their low toxicity and potential compatibility with aquaculture. The aim of this work was to 1) test coating solutions to prevent biofouling growth and saltwater corrosion on the static (paddle and attachment frame surface) components of the WEC that are submerged, 2) determine adhesion of the coatings to system components, and 3) assess the ease and effectiveness of biofouling cleaning to insure long term performance of the system. An analysis of commercial coatings was performed using methods to examine the prevention of biofouling and coating adhesion properties on two key materials of the WEC, which were 316L low carbon marine grade stainless steel (SS) and Ultra High Molecular Weight Polyethylene (PE). Three marine antifouling paints were selected based on their unique properties to test how different paint styles perform on different materials. The selected paints were ePaint Ecominder self-polishing paint with Zinc Omadine for slime control, Pettit ECO HRT Copper-Free ablative antifouling with Econea biocide, and Intersleek 1100SR foul release. Pacific Northwest National Laboratory (PNNL) prepared PE and SS substrates coated with the three paints and compared the performance against uncoated substrates when submerged in raw seawater for 3-, 6-, and 9-month (m) time periods. Results in adhesion testing indicated that Pettit and ePaint materials clearly bonded strongly to SS, but did not bond comparably well to PE. It was noted during adhesion testing that the Intersleek surfaces were especially difficult to test as the paint highly resists bonding to the epoxy adhesives used with the adherence testing platform. The wear rate of the coatings was not measured under this study; however, based on adhesion testing, coatings in the sliding regions of the Ewave device are expected to wear rapidly. Sandia National Laboratories (SNL) evaluated the adhesion of three different paints to PE and SS substrates which were exposed to a marine environment for time intervals of 0, 3, 6, and 9 months. From qualitative visual analysis of the 3 in2 coupons when pulled from the tank, the 3 in2 coupons generally only appeared to have biofouling consisting of filamentous algae or diatoms, which all have relatively low mass and can be easily wiped from the surface of coupons. Qualitative visual analysis indicated that ECO HRT and Unpainted were consistently worse than Intersleek and Ecominder at all time points. Results provide insight to aid with down-selection of commercial coatings under static conditions to support reliability of the WEC and potential maintenance schedules. This investigation was conducted using small coupon samples suspended in seawater and the development of testing rigs for dynamic component level testing is needed for future work. In addition, the potential toxicity of these commercial coatings on aquaculture has not been determined by this study. One recommendation is to conduct toxicity investigations at the Environmental Toxicity Laboratory at Oak Ridge National Laboratory.

16 TIDAL AND WAVE POWER↗
DOE OSTI2022

Ru Single Atoms on One-Dimensional CF@g-C 3 N 4 Hierarchy as Highly Stable Catalysts for Aqueous Levulinic Acid Hydrogenation

Herein, we report a stable catalyst with Ru single atoms anchored on a one-dimensional carbon fiber@graphitic carbon nitride hierarchy, by assembling wet wipes composed of fiber-derived carbon fiber (CF), melamine-derived graphitic carbon nitride (g-C3N4) and RuCl3 before NaBH4 reduction. The atomically dispersed Ru species (3.0 wt%) are tightly attached via N-coordination provided by exterior g-C3N4 nanosheets, and further stabilized by the interior mesoporous CF. The obtained CF@g-C3N4–Ru SAs catalyst can be cycled six times without notable leaching of Ru or loss of GVL yield in the acidic media. This catalyst is more stable than Ru nanoparticles supported on CF@g-C3N4, as well as Ru single atoms anchored on CF and g-C3N4, and proves to be one of the most efficient metal catalysts for aqueous LA hydrogenation to γ-valerolactone (GVL). The isolated Ru atoms by strong N-coordination, and their enhanced electron/mass transfer afforded by the one-dimensional hierarchy, can be responsible for the excellent durability of CF@g-C3N4–Ru SAs under harsh reaction conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1970

The dynamic characteristics of a turbo-rotor simulator supported on gas-lubricated foil bearings. Part 2: Operation with heating and thermal gradients

A high speed rotor, supported by gas-lubricated foil bearings, is free from self-excited whirl and displays no loss of load capacity when vibrated at frequency equal to the rotational speed. It is demonstrated that in addition to tolerance of geometrical imperfections, misalignment and foreign particles, the foil bearing performs well at elevated temperatures and accommodates appreciable temperature gradients. The foil bearing is endowed with superior wipe-wear characteristics and the flexibility of the foil accounts not only for the stability of the foil bearing, but also for its accommodation of, and compensation for, distortion, contamination, and contact.

Licht, L.↗
NASA NTRS1973

Design, fabrication, and performance of foil journal bearing for the brayton rotating unit

Foil bearings were designed and manufactured to replace pivoted-shoe journal bearings in an existing Brayton Cycle turbo-alternator-compressor. The design of this unconventional rotor support was accomplished within the constraints and space limitations imposed by the present machine, and the substitution of foil bearings was effected without changes or modification other machine components. A housing and a test rig were constructed to incorporate the new foil-bearing support into a unified assemble with an air-driven rotor and the gimbal-mounted thrust bearing, seals, and shrouds of an actual Brayton Rotating Unit. The foil bearing required no external pressure source, and stable self-acting rotation was achieved at all speeds up to 43,200 rpm. Excellent wipe-wear characteristics of the foil bearing permitted well over 1000 start-stop cycles with no deterioriation of performance in the entire speed range.

Licht, L.↗
NASA NTRS1973

Waste Management System overview for future spacecraft.

Waste Management Systems (WMS) for post Apollo spacecraft will be significantly more sophisticated and earthlike in user procedures. Some of the features of the advanced WMS will be accommodation of both males and females, automatic operation, either tissue wipe or anal wash, measurement and sampling of urine, feces and vomitus for medical analysis, water recovery, and solids disposal. This paper presents an overview of the major problems of and approaches to waste management for future spacecraft. Some of the processes discussed are liquid/gas separation, the Dry-John, the Hydro-John, automated sampling, vapor compression distillation, vacuum distillation-catalytic oxidation, incineration, and the integration of the above into complete systems.

Ingelfinger, A. L.↗
NASA NTRS1974

Long-duration life tests of slip ring capsule assemblies for inertial guidance platforms

Eight slip ring capsules, each having 80 or 100 circuits, were operated for time periods ranging from 14,300 hours to 24,700 hours. The test mode simulated the motion of gimbal axes of the Saturn inertial guidance the platform in an organic free nitrogen environment. Computer-compiled noise data (approximately 45,000 recordings) were graphed as a function of test time and position within the capsules and as extreme probability distributions. Greater than ninety-nine percent of the noise measurements for the capsules with sufficient lubrication were less than 10 milliohms. Capsules with glass dielectrics did not perform significantly differently than those with filled epoxy dielectrics. The initial wear mode of prow formation was followed by rider wear. After 10 to the 8th power wipes, ring wear depth did not exceed the surface finish and the radial rider wear depth was less than 13 microns.

Cole, S. R.↗
NASA NTRS1974

Preliminary flight prototype waste collection subsystem

The zero gravity test program demonstrated the feasibility and practicability of collecting urine from both male and female crew members in a zero gravity environment in an earthlike manner not requiring any manual handling of urine containers. In addition, the testing demonstrated that a seat which is comfortable in both regimes of operation could be designed for use on the ground and in zero-gravity. Further, the tests showed that the vortex liquid/air separator is an effective liquid/air separation method in zero gravity. Visual observations indicate essentially zero liquid carry over. The system also demonstrated its ability to handle post elimination wipes without difficulty. The designs utilized in the WCS were verified as acceptable for usage in the space shuttle or other space vehicles.

Swider, J. E., Jr.↗
NASA NTRS1973

Gas-lubricated foil bearings for high speed turboalternator - Construction and performance

Foil bearings were designed and fabricated to replace pivoted-shoe journal bearings in a Brayton cycle turboalternator, within space limitations and constraints imposed by the existing machine. The foil bearings were integrated into a unified assembly with the rotor, housing, seals, and gimbal-mounted thrust bearing, without changes and modifications of machine components other than the journal bearings. The gas-lubricated foil bearings, which require no external pressure-source, furnished a stable support for a 21.9 pound rotor in the vertical attitude at speeds to 43,200 rpm. Excellent wipe-wear characteristics permitted well over 1000 start-stop cycles, without deterioration of performance in the entire speed range. The paper reviews salient aspects of design, fabrication, and performance. An account is given of rotor dynamics during starting, stopping, and traversing the region of resonances. The state of journal and foil surfaces is examined following intensive start-stop cycling and high-speed runs over extended periods of time.

Licht, L.↗
NASA NTRS1974

The Boltzmann- and the Klimontovich formalisms with reference to turbulence resolution

The Navier-Stokes equation expressed in terms of Klimontovich microscopic density is compared with the conventional one based on the Boltzmann formalism. Their difference is described by the two-point BBGKY equation. An implication is given that the averaging procedure from the Klimontovich to the Boltzmann formalism wipes out not only thermal agitation, but also a certain hydrodynamic turbulence. This is substantiated by agreement with measurements due to Schubauer and Klebanoff.

Tsuge, S.↗
NASA NTRS1974

Techniques of biological contamination avoidance by atmospheric probes

The likelihood of biologically contaminating a planet by an atmospheric probe has a low probability of occurring if the probe is kept biologically clean during terrestrial operations and if the structure remains in tact until the planets life zone is completely penetrated. High standards of cleanliness, monitoring and estimating for remedial actions must be maintained in a probe program. It is not a foregone conclusion, however, that heat sterilization needs to be employed. The use of several techniques having a good potential for lower probe costs are available and appear adequate to render a probe sterile within acceptable bounds. The techniques considered to be satisfactory for minimizing microbial load include: (1) combined heat (at 95-105 C) and gamma radiation; (2) short term heating at 105 + or - 5 C to inactivate all vegetative microbes; (3) irradiation routinely by ultraviolet light; (4) wiping by a bactericidal agent with or without a penetrant; and (5) cleanliness alone.

Defrees, R. E.↗
NASA NTRS1977

Rotating-vector TV cursor

Device is used as wiping signal to cover adjustable 360 degree arc of television raster. Device can also be used to generate television alinement reference to assist remotely-controlled payload operations.

Freedman, L. A.↗
NASA NTRS1976

Whence cometh /and goeth/ Jupiter's high energy electrons

Jupiter's decimetric emission is universally identified as synchrotron radiation from about 10 MeV electrons. These electrons radiate away their energy in a few months and hence must be continuously replaced. A theory in which electrons are injected at Jupiter's magnetopause and radially diffuse toward the planetary surface, gaining energy in the process is summarized. The radial diffusion coefficient in the inner magnetosphere is determined. This diffusion coefficient, which also holds for protons, is sufficiently small that the inner Galilean satellites can wipe out large fractions of the incoming proton and electron fluxes. The reduction of the proton flux is extremely important to the survival of the Pioneer experimental payloads.

Birmingham, T. J.↗