Search NASA⌕ Search

SEARCH · Search NASA

Results for “abrasion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Epoxy / Silicone Potting Material Removal for Greater Recovery of Circuit Boards

This report documents an exploratory research project, “Epoxy/Silicone Potting Material Removal for Greater Recovery of Circuit Boards,” that investigated micro abrasion and laser ablation as potential cost effective methods for removal of epoxy and silicone potting material from printed circuit boards (PCBs) to expose components for testing and repair. The ability to cost effectively remove such PCB potting materials will improve PCB repair, remanufacture, and reuse opportunities with potential for sizable reductions in material use, E-waste, and energy. Laser ablation was identified as a method potentially warranting further investigation, in particular for epoxy based potting materials.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

R&D to Ensure a Scientific Basis for Qualification Tests and Standards (Final Report)

Project return on investment in a photovoltaic (PV) system depends increasingly on maintaining high energy yields, and the system lifetime is a major factor in levelized cost of electricity (LCOE). Thus, the rate of PV deployment and the success of these assets depends upon reliable long-term power generation. The overarching objective of this program is to improve photovoltaic (PV) module reliability via development of tests and standards. Where reliability problems or risk are discovered, we can design tests to ensure that these liabilities don't affect future generations of products. Customers can use these tests to understand which products are susceptible to certain degradation mechanisms, and manufacturers can use the tests to design unwanted characteristics out of their products. The work under this program identifies PV reliability needs, performs characterization that provides scientific understanding of targeted degradation mechanisms, and translates those data into practical and predictive test protocols and standards. Major accomplishments include: A model for polarization-type potential induced degradation (PID-p) was developed and validated against experimental data. NREL is currently leading a new edition of IEC 62804-1 for PID detection. PID-p can cause large losses in current and voltage for some module designs on cloudy days. Finite element modeling (FEM) and experiment was used to determine when cells crack in a module. It was shown that cells in landscape orientation are much more likely to crack than those on portrait orientation. Shortly thereafter, the first products with portrait-oriented cells were introduced. Studies of how to test for light and elevated temperature degradation (LeTID) culminated with the publication of IEC TS 63342. Software to predict the progression of LeTID was developed, validated, and made publicly available. Field validated tests and international standards for durability of PV module coatings abrasion, backsheets, and encapsulants were developed. Examples are IEC 62788-1-1, IEC 62788-2 ED2, IEC TS 62788-7-2, IEC 62788-7-3 ED1, IEC 63209-2. NREL led the development a high-temperature testing technical specification, and published guidelines that enable installers to determine whether higher-temperature testing is needed, simply based on location and mounting configuration. In a number of our case studies, variations in the bills of materials or workmanship have been associated with variations in reliability. These observations emphasize the importance of quality assurance to reliability. A framework for criticality (i.e. Pareto) analysis was developed and published. The framework helps us and other researchers determine what problems should be addressed for reliability research to have the biggest industry impact. NREL continues to participate actively in international standards development and stakeholder engagement activities, including organizing an annual PV Reliability Workshop. These activities are important for ensuring we address issues that are relevant and timely, and that we convey our results to those who may benefit.

14 SOLAR ENERGY↗
DOE OSTI2020

Erosion-Corrosion Detection in Carbon Steel Pipe Loops using SRNLs Thickness and Mass Loss Measurement Coupons - 20464

Structural health of waste transfer infrastructure is of utmost importance to DOE and communities surrounding their active sites. A Fitness-for-Service (FFS) program for the Waste Transfer System has been implemented by the US Department of Energy (DOE) for the purposes of evaluating and quantifying the degradation of critical components. Currently, the method of approach is to section and evaluate pipelines that have been removed at end service. In order to augment data collection methods applied to making lifespan estimates of waste transfer system components, Florida International University (FIU) has been investigating new-technology based strategies for quantifying the rate of degradation. Present research considers the option of a coupon system installed on a section of pipe at points of interest that will provide easy access to high resolution measurements of erosion/corrosion rates during operation. Researchers at Savannah River National Laboratory (SRNL) have developed this novel solution for in situ erosion and corrosion measurements in many applicable locations such as tanks, pipes, ducts, and injection points. The coupons are approximately 12.7 mm (1/2 inch) in diameter and 25.4 mm (1 inch) in length and can be placed in the pipe sections using Swagelok compression fittings. The coupon design allows for monitoring of the total degradation resulting from corrosion and erosion. High-resolution Ultrasonic Thickness (UT) testing allows in-situ monitoring of both degradation mechanisms. When removed from the system mass loss resulting from corrosion and erosion may also be evaluated. Experimental testing at FIU implemented the SRNL coupon system in a 6.10 meter (20 foot) pipe loop system comprised of 50.8 mm (2 inch) and 76.2 mm (3 inch) pipe sections in order to replicate expected use cases at the sites. Operational conditions were emulated by pumping abrasive materials through the pipeline at full capacity and collecting measurements from the SRNL coupons. Initial testing was conducted by circulating water followed by a mixture of sand and water for uniform wear rates. Thickness changes and mass loss were measured, and the surface exposed to the process fluid was observed for visual evidence of characteristic wear patterns resulting from an erosive environment. The test matrix consisted of several hours of operation and using fine, medium and coarse grain sands. Test results were analyzed to check for all three parameters (mass loss/gain, thickness change and surface patters) which could provide estimates of the remaining useful life of the pipe sections. Thus, the research presents the findings of this evaluation of the SRNL coupons as a means for conducting high accuracy, cost effective in-situ analysis of pipeline and waste transfer systems for erosion and corrosion susceptibility. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Superhard Materials: Advances in the Search and Synthesis of New Materials

Materials with superior hardness can be categorized as ultrahard (Vickers hardness, H v ≥ 80 GPa) and superhard (H v ≥ 40 GPa). These materials are commonly used as cutting tools and abrasives in the machining and manufacturing industries. With its extreme hardness, diamond is the best known and most used ultrahard material for industrial applications. However, it is ineffective at cutting and drilling ferrous alloys due to diamond's high reactivity with iron and poor thermal stability in air. Additionally, the synthesis of diamond requires both high pressure (HP) and high temperature, making it an expensive process. These limitations have driven the search for alternative superhard materials that are capable of cutting steels and other materials at lower costs. This article reviews the concept of hardness and summarizes advancements in the synthesis and mechanical properties of hard materials. It begins with a review of methods to measure hardness, adding HP diffraction methods to more conventional hardness measurements. It then considers new ultrahard materials that exist within the B–C–N ternary system, with hardness approaching diamond but improved chemical stability. Finally, it surveys superhard nitrides, oxides, and borides as potential alternative materials, focusing on transition metal boride systems where the synthesis can be readily achieved at ambient pressure and scaled for industrial applications. We hope that this article serves as an overview of hard materials and guide for the comparison of data reported in the literature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Material-Dependent Antagonistic Effects between Soot and ZDDP

While soot in engine oil is known to accelerate the wear of diesel and gasoline direct-injection compression-ignition engines, there is a lack of consensus on the wear mechanism though various hypotheses have been proposed in the literature. Particularly, some recently observed antagonistic effects between soot and a common lubricant antiwear additive, zinc dialkyldithiophosphate (ZDDP), while others did not. The discrepancy is, in part, explained by the strong alloy dependence of such antagonism discovered in this study. Specifically, four alloys, 52100 steel and M2, M50, and A2 tool steels, are tested in lubricants containing carbon black (CB, a soot surrogate) with and without ZDDP present. Adding the CB alone to the oil increases the wear rate for all steel alloys as expected. However, distinct wear performance is observed for the four steel alloys when ZDDP is introduced to the CB-containing oil: while the 52100 steel has notable wear reduction, the three tool steels suffer significant wear increase. Comprehensive tribofilm characterization suggests that the Mo content in the steel alloy and the sulfur from ZDDP strongly influence wear behavior. The combination of CB/Mo-catalyzed sulfidation and CB-accelerated abrasion is hypothesized to be responsible for the high wear of the Mo-alloyed tool steels.

36 MATERIALS SCIENCE↗
DOE OSTI2026

An Anisotropic Yield and Damage Material Model to Improve the Contact Pressure Analysis in a Biomass Shredding System

Size reduction systems used in biomass processing break biomass into smaller pieces by utilizing the kinetic energy from the sharp rotating blades. Abrasive and/or erosive wear caused by biomass comminution results in blade wear of the sharp edged cutters, deteriorating the process efficiency. Here, this study aims to optimize the blade design and improve the system efficiency by attempting to understand the interactions between the blades and biomass particles. Since real-time monitoring of these interactions is impractical during operation, mechanical simulations offer a viable alternative for investigating the shredding process. Yet, the irregular geometry and complex mechanical properties of biomass—such as the anisotropic nature of woodchips and their nonlinear fracture behavior—pose significant challenges for accurately simulating contact pressure. In this work an anisotropic yield material model, along with a damage initiation and evolution function, is applied to the woodchip particle to study the contact pressure on shredder blade, offering a scientific basis for improved blade design and process efficiency. This approach can be extended to other biomass processing systems with similar anisotropic feedstocks, making it a valuable tool for advancing sustainable biomass utilization.

09 - BIOMASS FUELS↗
DOE OSTI2025

A New Method for Polishing Laminated Dissimilar Metals

Here, this paper presents a novel method for preparing metallographic samples of laminated dissimilar metals, specifically a layered structure of zirconium (Zr), vanadium (V), and tungsten (W), which pose a challenge due to their differing crystal structures and hardness levels. The work was motivated by the need to develop a cladding for tungsten targets in spallation neutron sources, where a zirconium face is applied over an interlayer of either vanadium or titanium to prevent the formation of brittle intermetallic compounds such as ZrW 2 . Traditional polishing techniques prove inadequate because each constituent metal requires a different polishing approach based on its unique material properties. The methodology outlined includes a sequential process involving conductive epoxy mounting, successive grinding and polishing with specific abrasives, and a final chemical-mechanical polish using a colloidal silica-based solution. Optical microscopy confirmed that this multi-step process successfully produced scratch-free surfaces and minimized surface relief across the different metal interfaces. Although developed for refractory metals, this approach shows promise for other layered structures comprised of transition metals, offering a meticulous yet effective technique for high-quality metallographic sample preparation.

Newberry, Daniel [Oak Ridge National Laboratory (O↗
DOE OSTI2020

Graphene nanoplatelet for enhancement the mechanical properties and durability characteristics of alkali activated binder

The effects of the addition of graphene nanoplatelets (GNPs) on the microstructure, heat of hydration, mechanical properties and durability characteristics of alkali activated binders were investigated. A simple mixing process led to reasonably uniform dispersion of GNPs in the matrix, with minor agglomeration of GNPs detected via scanning electron microscopy. Tests on engineering properties indicated that the compressive strength of the alkali activated binder increased with the addition of GNPs at relatively low concentrations. Gains were also realized in the abrasion resistance and moisture sorptivity of the binder with GNPs addition. The heat of hydration investigations indicated that the addition of GNPs accelerates the hydration process and increases the amount of hydration products, especially at early ages. Scanning electron microscope investigations further indicated that GNPs could impede the development of microcracks and mitigate their propagation within matrix; indications of good bonding between the GNPs and the alkali activated matrix were also noted.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Localised instability of titanium during its erosion-corrosion in simulated acidic hydrometallurgical slurries

Electrochemical techniques were used to investigate the erosion-corrosion of titanium in simulated acidic mineral leaching slurries. Erosion-corrosion of titanium was caused by solid particle impingement. Electrochemical noise revealed that solid particle impacts resulted in localised fracture of the passive film, and erosion-corrosion of titanium proceeded in the form of current transients. As conditions become more abrasive, erosion-corrosion is an increasing threat to titanium equipment exposed to acidic slurries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of artificial aging on corrosion of abraded Al-Zn-Mg-Cu alloys

Surface abrasion has been shown to create altered surface layers (ASLs) that are hundreds of nm thick on all types of Al alloys. Such ASLs have lower corrosion resistance than the underlying substrate of Al-Zn-Mg-Cu alloys. Here, we demonstrate how heat treatments affect the ASL microstructure on abraded Al-Zn-Mg-Cu alloys using transmission electron microscopy and atom probe tomography, and also how the corrosion properties change using electrochemical polarization. Additionally, high temperature treatments on the abraded bulk samples enhance η phase precipitation in the ASL, leading to a decreased Zn content in the ASL solid solution, which ennobles the ASL breakdown potential.

36 MATERIALS SCIENCE↗
DOE OSTI2020

U-Pb zircon age constraints on the earliest eruptions of the Deccan Large Igneous Province, Malwa Plateau, India

Climate instability driven by emission of volatiles during emplacement of large igneous provinces (LIPs) is frequently invoked as a potential cause of mass extinctions. However, documenting this process in the geologic record requires a holistic understanding of eruption rates, the location of eruptive centers, and potential sources of climate-changing volatiles. We present new chemical abrasion–isotope dilution–thermal ionization mass spectrometry (CA-ID-TIMS) U-Pb zircon geochronology from Malwa Plateau basalts on the northern margin of the Deccan LIP, India. These basalts have been previously interpreted as either an extension of the province's main volcanic stratigraphy or as an independent eruptive center active up to millions of years prior to the main eruptive phase. Our data instead demonstrate that the lower Malwa Plateau basalts are temporally correlative with the first pulse of Deccan volcanism and provide new constraints on its initiation and duration. Paleomagnetic data further indicate that upper Malwa Plateau basalts may be age-equivalent to the second, third, and fourth pulses of Deccan volcanism. The relative thicknesses of age-equivalent packages of basalt are consistent with eruption of the Deccan LIP from a southward-migrating eruptive center. The first eruptive pulse is coeval with a ~200 kyr Late Maastrichtian warming event preserved globally in contemporaneous stratigraphic sections. We propose that the first pulse of Deccan magmatism was more voluminous in the north, where it erupted through organic-rich sedimentary rocks of the Narmada-Tapti rift basin. Thermal metamorphism of these sediments could have been a source of sufficient CO 2 to drive the Late Maastrichtian warming event, which if true would reconcile the apparent dampened warming signals associated with later Deccan eruptive pulses.

58 GEOSCIENCES↗
DOE OSTI2023

Sidewall Breach During Lithium-Ion Battery Thermal Runaway Triggered by Cell-to-Cell Propagation Visualized Using High-Speed X-Ray Imaging

With the rapid deployment of Li-ion batteries (LiBs) in a range of applications, it is crucial to ensure their safe operation. Therefore, it is necessary to investigate the rapid thermal runaway failure that LiBs can undergo if improperly operated or subjected to abuse scenarios so that hazardous events can be avoided or mitigated. Sidewall breaches or ruptures of LiBs during thermal runaway are considered the most hazardous failure scenario, resulting in hot abrasive flare from the casing of the cell that can impinge on neighbouring cells and lead to the propagation of thermal runaway throughout a battery pack. Yet, the process leading up to the sidewall breach is not well understood due to the extreme difficulty in visualizing such a failure in commercially relevant cells. With the application of a newly developed chamber for remote-controlled abuse testing of batteries coupled with simultaneous X-ray imaging, we demonstrate here for the first time an in-situ visualization of a sidewall breach. By further applying spatiotemporal mapping techniques, the internal thermal runaway events leading up to the sidewall breach can be analyzed in detail. Subsequently, the speed of the electrode layer delamination could be calculated to a speed of 0.6 m/s. These new insights bring more clarity regarding this phenomenon, that in turn can help battery designers improve battery safety.

battery safety↗
DOE OSTI2024

A non-isothermal breakage-damage model for plastic-bonded granular materials incorporating temperature, pressure, and rate dependencies

Plastic-bonded granular materials (PBM) are widely used in industrial sectors, including building construction, abrasive applications, and defense applications such as plastic-bonded explosives. The mechanical behavior of PBM is highly nonlinear, irreversible, rate dependent, and temperature sensitive governed by various micromechanical attributions such as grain crushing and binder damage. This paper presents a thermodynamically consistent, microstructure-informed constitutive model to capture these characteristic behaviors of PBM. Key features of the model include a breakage internal variable to upscale the grain-scale information to the continuum level and to predict grain size evolution under mechanical loading. In addition, a damage internal state variable is introduced to account for the damage, deterioration, and debonding of the binder matrix upon loading. Temperature is taken as a fundamental external state variable to handle non-isothermal loading paths. The proposed model is able to capture with good accuracy several important aspects of the mechanical properties of PBM, such as pressure-dependent elasticity, pressure-dependent yield strength, brittle-to-ductile transition, temperature dependency, and rate dependency in the post-yielding regime. Furthermore, the model is validated against multiple published datasets obtained from confined and unconfined compression tests, covering various PBM compositions, confining pressures, temperatures, and strain rates.

Breakage↗
DOE OSTI2022

Atomistic simulations of nanoindentation on nanoglasses: Effects of grain size and gradient microstructure on the mechanical properties

The use of nanoglass (NG) microstructures has been shown as an effective strategy to improve the ductility of rather brittle metallic glass alloys. To evaluate the effects of grain size and gradient design on the mechanical properties of NGs, we perform molecular dynamics simulations of nanoindentation on Cu 64 Zr 36 NGs. We consider samples with uniform 3 and 7 nm grain sizes as well as gradient microstructures with gradient grain sizes varying from 3 to 7 nm. Here, the results show that the deformation mechanism in NGs with small grain sizes is dominated by the activation and evolution of multiple shear transformation zones. Increasing grain sizes enhances the elastic modulus and hardness at the cost of reduced abrasion resistance. Though the average grain size at the indentation surface plays a crucial role in the deformation behavior of gradient NG models, their strain localization and plastic deformation states are affected by the grain sizes far from the indenter. Desired combinations of mechanical properties can be realized by different NG microstructure designs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tribological behavior of ceramic-alloy bearing contacts in molten salt lubrication for concentrating solar power

Molten salts are considered as candidate heat transfer fluids and thermal energy storage media for next generation concentrating solar power (CSP). A molten salt circulates inside the piping and heat exchanger and also functions as a lubricant for the sleeve bearings of the CSP pump. Furthermore, wear- and corrosion-resistant high-temperature bearing materials are critical for the pump efficiency and durability. This study evaluated the tribological performance of candidate bearing materials in lubrication of a molten chloride salt mixture (20% NaCl + 40% MgCl 2 + 40% KCl) at 750 °C in an inert argon gas (a simulative CSP pump environment). Six ceramic-alloy pairs were tested, zirconia and silicon nitride against Haynes 244, Hastelloy C276, and Tribaloy T900 alloy, and ranked by the friction coefficient and wear loss. Characterization of worn surfaces suggested the wear mechanism as a combination of abrasion, adhesion, and tribocorrosion. Results from this study provide fundamental insight for the development and selection of bearing materials for molten salt powered CSP pumps.

14 SOLAR ENERGY↗
DOE OSTI2021

Why does a phosphonium-phosphinate ionic liquid protect the contact surfaces from wear and micropitting but increase vibration when used as an additive in rolling-sliding lubrication?

A phosphonium-phosphinate ionic liquid (IL) was studied as a lubricant additive for rolling-sliding contacts. The bench-scale test was designed to simulate automotive rear axle operation during cold start, highway towing, and overload conditions. Adding such an IL (2%) into a base oil significantly reduced wear loss and rolling contact fatigue, e.g., microcracking and micropitting, but made the vibrational noise notably higher under a low (-1.5%) sliding roll ratio (SRR). Additionally, worn surface characterization revealed an interesting texture pattern with alternating smoother plateaus and rougher valleys, which is believed to cause the high vibration. No increased vibration was observed at a high (-30%) SRR, possibly because the more aggressive sliding abrasion prevented such a surface texture from forming.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Tribological behavior of spark plasma sintered Ti 3 SiC 2 MAX phase composites

Ti₃SiC₂ MAX phases are considered promising candidates for tribological applications; but, their low hardness (5-6 GPa) can lead to increased abrasive wear and higher wear rates. This study investigates the effect of incorporating hard SiC particles on microstructure, mechanical, and tribological behavior of Ti₃SiC₂-SiC-based MAX phase composites prepared using spark plasma sintering at 1400 °C, 40 MPa, 15-minute holding time. Phase and microstructural characterization of composites confirmed the formation of Ti₃SiC₂ MAX phase (90%) along with TiC as a minor phase (10%). For Ti₃SiC₂-SiC, homogeneous distribution of SiC grains within Ti₃SiC₂ matrix resulted in increased hardness from ~11.6 GPa to ~14.8 GPa; however, the flexural strength decreased from ~615 MPa to ~597 MPa due to coefficient of thermal expansion mismatch. Tribological behavior of Ti₃SiC₂-SiC MAX phase composites was assessed using unidirectional sliding ball-on-flat tests with a 52100 steel ball at different loads and a constant speed of 0.05 m/s. SiC reinforced composites exhibited a decreased friction coefficient from 0.39 to 0.29 and wear rates comparable to Ti₃SiC₂ (7-10×10⁻³ mm³/N·m). SEM and EDS analysis of the worn surfaces indicated material transfer from the steel ball counter body and its oxidation due to frictional heating, at lower loads (2N and 5N), whereas at higher load (10N), fracture of the transfer layer dominated, with the presence of microcracks, delamination, grain pull-outs, and wear debris. Improved mechanical properties and good adhesion of SiC with Ti₃SiC₂ matrix resulted in reduced microcracks and grain pull-outs, making Ti₃SiC₂-SiC/Steel tribo-pair more suitable for tribological applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Grid-to-rod fretting wear study of SiC/SiC composite accident-tolerant fuel claddings using an autoclave fretting bench test

Grid-to-rod-fretting (GTRF) in pressurized water reactors (PWRs) is known to cause wear and surface damage on the fuel claddings, potentially leading to radioactive leakage. One of the accident-tolerant fuel (ATF) concepts is to use advanced cladding materials that could withstand higher temperatures. Here, we investigated the wear behavior of candidate silicon carbide (SiC)-based composite claddings with different levels of surface finish in fretting against a commercial ZIRLO alloy grid using a unique bench-scale autoclave GTRF rig. The experiments mimicked the environment in an industrial full-assembly PWR simulator. Fretting tests were conducted with a realistic load (~0.5 N) in deionized water under a pressure of 20–23 bar at 204 °C for 100 h. While the SiC/SiC composite claddings showed significantly higher wear resistance than the commercial ZIRLO alloy cladding as expected, the smoother versions experienced surprisingly higher wear than the much softer counterface, ZIRLO grid. The wear mechanism of the SiC/SiC cladding was attributed to the SiC wear debris that was trapped at the fretting interface causing both 3-body and 2-body (embedded into the grid surface) abrasion of the cladding. Rougher SiC/SiC claddings had less material loss but caused more wear on the ZIRLO grid. Finally, pre-oxidized ZIRLO grid showed better compatibility with the SiC/SiC cladding to protect both the cladding and grid as a result of reduced wear debris trapping.

36 MATERIALS SCIENCE↗