Search NASA⌕ Search

SEARCH · Search NASA

Results for “active flow control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Active Flow Control at Low Reynolds Numbers on a NACA 0015 Airfoil

Results from a low Reynolds number wind tunnel experiment on a NACA 0015 airfoil with a 30% chord trailing edge flap tested at deflection angles of 0, 20, and 40 are presented and discussed. Zero net mass flux periodic excitation was applied at the ap shoulder to control flow separation for flap deflections larger than 0. The primary objective of the experiment was to compare force and moment data obtained from integrating surface pressures to data obtained from a 5-component strain-gage balance in preparation for additional three-dimensional testing of the model. To achieve this objective, active flow control is applied at an angle of attack of 6 where published results indicate that oscillatory momentum coefficients exceeding 1% are required to delay separation. Periodic excitation with an oscillatory momentum coefficient of 1.5% and a reduced frequency of 0.71 caused a significant delay of separation on the airfoil with a flap deflection of 20. Higher momentum coefficients at the same reduced frequency were required to achieve a similar level of flow attachment on the airfoil with a flap deflection of 40. There was a favorable comparison between the balance and integrated pressure force and moment results.

Melton, LaTunia Pack↗
NASA NTRS2012

Numerical Simulation of Fluidic Actuators for Flow Control Applications

Active flow control technology is finding increasing use in aerospace applications to control flow separation and improve aerodynamic performance. In this paper we examine the characteristics of a class of fluidic actuators that are being considered for active flow control applications for a variety of practical problems. Based on recent experimental work, such actuators have been found to be more efficient for controlling flow separation in terms of mass flow requirements compared to constant blowing and suction or even synthetic jet actuators. The fluidic actuators produce spanwise oscillating jets, and therefore are also known as sweeping jets. The frequency and spanwise sweeping extent depend on the geometric parameters and mass flow rate entering the actuators through the inlet section. The flow physics associated with these actuators is quite complex and not fully understood at this time. The unsteady flow generated by such actuators is simulated using the lattice Boltzmann based solver PowerFLOW R . Computed mean and standard deviation of velocity profiles generated by a family of fluidic actuators in quiescent air are compared with experimental data. Simulated results replicate the experimentally observed trends with parametric variation of geometry and inflow conditions.

Vasta, Veer N.↗
NASA NTRS2006

Turbulence Measurements on a 2D NACA 0036 with Synthetic Jet Flow Control

An active flow control experiment was conducted on a 2-ft chord NACA 0036 airfoil in a 3-ft by 4-ft Wind Tunnel at Re = 1 x 10(exp 6). The model was equipped with synthetic jet actuators at x/c = 0.30 and 0.65 that provided 120 Hz periodic excitation at a C(sub mu) 0.86% through 0.06-in wide slots. Three different slot con gurations were tested, including a baseline with no slots. Surface pressure data was collected to compare to previous tests and to combine with turbulence data to aid future CFD modeling efforts. Turbulence data, measured by hot-wire, was compared with and without flow control. Pressure data corroborates previous test data and provides more points for CFD validation. Hot-wire results showed ow control reduced the separated wake size and brought the high Reynolds stress shear layer closer to the airfoil surface. The position of this layer to the surface was altered more significantly than the magnitude of the peak stresses. Flow control was shown to increase turbulent energy in the attached boundary layer downstream of the slot but to have little effect upstream. These results provide further justification to continue assessing the potential of active flow control to reduce drag of helicopter airframe components.

Wilson, J. S.↗
NASA NTRSDate not supplied

Surface-Normal Active Flow Control for Lift Enhancement and Separation Mitigation for High-Lift Common Research Model

This study explores the feasibility of using small surface-normal jets near the flap trailing edge as active aerodynamic load control on the high-lift Common Research Model wing/-body configuration. Chimera Grid Tools are utilized to generate structured curvilinear overset grids, and the Reynolds-averaged Navier-Stokes solver OVERFLOW is employed to solve for the flow-field around the geometry. The so-called microjet is initially employed across both the inboard and the outboard flaps on the pressure-side near the trailing edge. It is shown that implementing the microjet on the inboard flap is more effective compared to implementing it on the outboard flap. This is because, prior to microjet implementation, the flow on the outboard flap exhibits extensive separation, while the flow on the inboard flap exhibits moderate separation. For microjet implementation across the inboard flap only, the relationship between momentum coefficient of the microjet and lift-enhancement is found to be∆CL'1.66√Cμfor the rangeCμ= 0.00−0.012. We show that implementing a microjet with a jet velocity ratio of one, which corresponds toCμ= 0.003, can shift the linear region of the lift curve by ∆CL= 0.08. The linear shift in the lift curve is significant for enhancing airplane performance such as increasing its payload. Microjet implementation effects on the drag coefficient are also investigated through a drag decomposition analysis. Further, we employ an induced drag analysis based on the spanwise load distribution and show that the microjet-related increase in pressure drag coefficient is dominated by the increase in the induced drag while microjet implementation reduces the form drag. These preliminary results show that favorable changes in aerodynamic performance can be achieved by using the surface-normal jets presented in this study.

ARMD↗
NASA NTRS2010

Minnowbrook VI: 2009 Workshop on Flow Physics and Control for Internal and External Aerodynamics

Topics covered include: Flow Physics and control for Internal and External Aerodynamics (not in TOC...starts on pg13); Breaking CFD Bottlenecks in Gas-Turbine Flow-Path Design; Streamwise Vortices on the Convex Surfaces of Circular Cylinders and Turbomachinery Blading; DNS and Embedded DNS as Tools for Investigating Unsteady Heat Transfer Phenomena in Turbines; Cavitation, Flow Structure and Turbulence in the Tip Region of a Rotor Blade; Development and Application of Plasma Actuators for Active Control of High-Speed and High Reynolds Number Flows; Active Flow Control of Lifting Surface With Flap-Current Activities and Future Directions; Closed-Loop Control of Vortex Formation in Separated Flows; Global Instability on Laminar Separation Bubbles-Revisited; Very Large-Scale Motions in Smooth and Rough Wall Boundary Layers; Instability of a Supersonic Boundary-Layer With Localized Roughness; Active Control of Open Cavities; Amplitude Scaling of Active Separation Control; U.S. Air Force Research Laboratory's Need for Flow Physics and Control With Applications Involving Aero-Optics and Weapon Bay Cavities; Some Issues Related to Integrating Active Flow Control With Flight Control; Active Flow Control Strategies Using Surface Pressure Measurements; Reduction of Unsteady Forcing in a Vaned, Contra-Rotating Transonic Turbine Configuration; Active Flow Control Stator With Coanda Surface; Controlling Separation in Turbomachines; Flow Control on Low-Pressure Turbine Airfoils Using Vortex Generator Jets; Reduced Order Modeling Incompressible Flows; Study and Control of Flow Past Disk, and Circular and Rectangular Cylinders Aligned in the Flow; Periodic Forcing of a Turbulent Axisymmetric Wake; Control of Vortex Breakdown in Critical Swirl Regime Using Azimuthal Forcing; External and Turbomachinery Flow Control Working Group; Boundary Layers, Transitions and Separation; Efficiency Considerations in Low Pressure Turbines; Summary of Conference; and Final Plenary Session Transcript.

LaGraff, John E.↗
NASA NTRS2010

Progress Towards Fuselage Drag Reduction via Active Flow Control: A Combined CFD and Experimental Effort

A combined computational and experimental effort has been undertaken to study fuselage drag reduction on a generic, non-proprietary rotorcraft fuselage by the application of active ow control. Fuselage drag reduction is an area of research interest to both the United States and France and this area is being worked collaboratively as a task under the United States/France Memorandum of Agreement on Helicopter Aeromechanics. In the first half of this task, emphasis is placed on the US generic fuselage, the ROBIN-mod7, with the experimental work being conducted on the US side and complementary US and French CFD analysis of the baseline and controlled cases. Fuselage simulations were made using Reynolds-averaged Navier-Stokes ow solvers and with multiple turbulence models. Comparisons were made to experimental data for numerical simulations of the isolated fuselage and for the fuselage as installed in the tunnel, which includes modeling of the tunnel contraction, walls, and support fairing. The numerical simulations show that comparisons to the experimental data are in good agreement when the tunnel and model support are included. The isolated fuselage simulations compare well to each other, however, there is a positive shift in the centerline pressure when compared to the experiment. The computed flow separation locations on the rear ramp region had only slight differences with and without the tunnel walls and model support. For the simulations, the flow control slots were placed at several locations around the flow separation lines as a series of eight slots that formed a nearly continuous U-shape. Results from the numerical simulations resulted in an estimated 35% fuselage drag reduction from a steady blowing flow control configuration and a 26% drag reduction for unsteady zero-net-mass flow control configuration. Simulations with steady blowing show a delayed flow separation at the rear ramp of the fuselage that increases the surface pressure acting on the ramp, thus decreasing the overall fuselage pressure drag.

Schaeffler, Norman W.↗
NASA NTRSDate not supplied

Aerodynamic Assessment of Surface-Normal Active Flow Control for Lift Enhancement on the High-Lift Common Research Model

This study explores aerodynamic feasibility of small surface-normal pneumatic jets (micro-jets) for lift enhancement on the high-lift Common Research Model. To date, lift enhancement studies using microjets have been conducted at wind tunnel Reynolds numbers less than three and half million. This paper computationally investigates microjet effects at a flight Reynolds number of24.6million. Prior to microjet activation, it is shown that flow features such as trailing edge (TE) flow separation on both inboard and outboard flaps have noticeable sensitivity to Reynolds number. At the flight Reynolds number, the onset of TE flow separation shifts downstream resulting in less flow separation compared to at the wind tunnel Reynolds numberof3.26million. The effects are insignificant for lift enhancement due to microjet on the inboard flap. However, the effects are significant for lift enhancement on the outboard flap. Microjets are shown to be more effective in circulation control on the outboard flap at the higher Reynolds number. For a microjet with velocity ratio of one, lift enhancement is increased by17%at the flight Reynolds number. This highlights the sensitivity of microjet performance to the flow features of the configuration it is implemented on. Microjet lift enhancement trends at both Reynolds numbers are found to be consistent in their ability to move the lift curve upwards in the linear regime, with the lift enhancement related to microjet momentum coefficient throughΔ𝐶𝐿=𝐾√︁𝐶𝜇. Analysis of the impact microjets have on drag shows that microjets improve the configuration’s Oswald efficiency by5.4%and2.5%at the wind tunnel and flight Reynolds numbers respectively, while providing lift enhancement. Microjet effects on the trim drag are found to be less than one percent of the total drag. The results of this study highlight the potential of small surface-normal pneumatic jets for improved performance at high-lift conditions.

ARMD↗
DOE OSTI2013

Active Flow Control on Bidirectional Rotors for Tidal MHK Applications

A marine and hydrokinetic (MHK) tidal turbine extracts energy from tidal currents, providing clean, sustainable electricity generation. In general, all MHK conversion technologies are confronted with significant operational hurdles, resulting in both increased capital and operations and maintenance (O&M) costs. To counter these high costs while maintaining reliability, MHK turbine designs can be simplified. Prior study found that a tidal turbine could be cost-effectively simplified by removing blade pitch and rotor/nacelle yaw. Its rotor would run in one direction during ebb and then reverse direction when the current switched to flood. We dubbed such a turbine a bidirectional rotor tidal turbine (BRTT). The bidirectional hydrofoils of a BRTT are less efficient than conventional hydrofoils and capture less energy, but the elimination of the pitch and yaw systems were estimated to reduce levelized cost of energy by 7.8%-9.6%. In this study, we investigated two mechanisms for recapturing some of the performance shortfall of the BRTT.

16 TIDAL AND WAVE POWER↗
NASA NTRS2003

Transient Growth Theory Prediction of Optimal Placing of Passive and Active Flow Control Devices for Separation Delay in LPT Airfoils

An analysis of the non-modal growth of perturbations in a boundary layer in the presence of a streamwise pressure gradient is presented. The analysis is based on PSE equations for an incompressible fluid. Examples with Falkner-Skan profiles indicate that a favorable pressure gradient decreases the non-modal growth while an unfavorable pressure gradient leads to an increase of the amplification. It is suggested that the transient growth mechanism be utilized to choose optimal parameters of tripping elements on a low-pressure turbine (LPT) airfoil. As an example, a boundary layer flow with a streamwise pressure gradient corresponding to the pressure distribution over a LPT airfoil is considered. It is shown that there is an optimal spacing of the tripping elements and that the transient growth effect depends on the starting point. At very low Reynolds numbers, there is a possibility to enhance the transient energy growth by means of wall cooling.

Tumin, Anatoli↗
NASA NTRS2005

Sensing and Active Flow Control for Advanced BWB Propulsion-Airframe Integration Concepts

In order to realize the substantial performance benefits of serpentine boundary layer ingesting diffusers, this study investigated the use of enabling flow control methods to reduce engine-face flow distortion. Computational methods and novel flow control modeling techniques were utilized that allowed for rapid, accurate analysis of flow control geometries. Results were validated experimentally using the Techsburg Ejector-based wind tunnel facility; this facility is capable of simulating the high-altitude, high subsonic Mach number conditions representative of BWB cruise conditions.

Fleming, John↗
NASA NTRS2010

Some Issues Related to Integrating Active Flow Control With Flight Control

Time varying control of CL is necessary for integrating AFC and Flight Control (Biasing allows for +/- changes in lift) Time delays associated with actuation are long (APPROX.5.8 c/U) and must be included in controllers. Convolution of input signal with single pulse kernel gives reasonable prediction of lift response.

Williams, David↗
NASA NTRS2011

Numerical Investigation of Rotorcraft Fuselage Drag Reduction Using Active Flow Control

The effectiveness of unsteady zero-net-mass-flux jets for fuselage drag reduction was evaluated numerically on a generic rotorcraft fuselage in forward flight with a rotor. Previous efforts have shown significant fuselage drag reduction using flow control for an isolated fuselage by experiment and numerical simulation. This work will evaluate a flow control strategy, that was originally developed on an isolated fuselage, in a more relevant environment that includes the effects of a rotor. Evaluation of different slot heights and jet velocity ratios were performed. Direct comparisons between an isolated fuselage and rotor/fuselage simulations were made showing similar flow control performance at a -3deg fuselage angle-of-attack condition. However, this was not the case for a -5deg angle-of-attack condition where the performance between the isolated fuselage and rotor/fuselage were different. The fuselage flow control resulted in a 17% drag reduction for a peak C(sub mu) of 0.0069 in a forward flight simulation where mu = 0:35 and CT/sigma = 0:08. The CFD flow control results also predicted a favorable 22% reduction of the fuselage download at this same condition, which can have beneficial compounding effects on the overall performance of the vehicle. This numerical investigation was performed in order to provide guidance for a future 1/3 scale wind tunnel experiment to be performed at the NASA 14-by 22-Foot Subsonic Tunnel.

Allan, Brian G.↗