Search NASA⌕ Search

SEARCH · Search NASA

Results for “ammonia separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

71 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Supercritical Water Oxidation: Testing of Ersatz Wastewater

Supercritical Water Oxidation (SCWO) technology is under consideration by NASA for treatment of wastewater and other wet waste streams. The dramatic changes in water's thermophysical properties near its critical point (374◦C and 22 MPa) result in nearly complete solubility of organics and gases. The absence of inter–phase transport processes and phase separation results in dramatically reduced reaction timescales and the elimination of complications of two–phase transport and processing in reduced gravity. Other advantages are that the product streams are microbially inert,benign, amenable to resource recovery and organic waste. This paper first described the design and construction of tubular SCWO reactor built at NASA Glenn. It consists of separate wastewater and oxidizer inlets, which are independently heated and pressurized to conditions approaching the critical point of water. These flows enter a reactor chamber having a volume of 62 ml. The reactor section is heated to the desired temperature in the range of 450 ◦C – 650 ◦C. A pressure regulator maintains the operating pressure nominally between 27.6 MPa and 28.3 MPa. The reacted fluid is captured downstream of the pressure regulator during an experiment run. A separate vent line may also be used for collection of the effluent. Next, the results of SCWO experiments using both a representative organic (ethanol) as well as a wastewater simulant provided by NASA Ames are presented. Raman analysis of the pre–reacted and post–reacted solutions are presented. Finally, initial efforts on supplementary chemical kinetics modeling of ethanol oxidation with and without inclusion of a nitrogenous compounds (ammonia) are presented.

Michael C Hicks↗
NASA NTRS1985

Propagation of detonations in hydrazine vapor

In the range of greater hydrazine vapor pressure, detonation speed depends exclusively on the extent of the ammonia decomposition in the second reaction stage. As vapor pressure decreases, the ammonia disintegration speed becomes increasingly slower and the reaction reached in the reaction zone increasingly decreases until finally, in the vapor pressure range between 53 and 16 Torr, the contribution of the second stage to detonation propagation disappears, and only the first stage remains active. Since the disintegration speed of the hydrazine in this pressure range has decreased markedly as well, no level, but rather only spinning, detonations occur. Temporary separations of the impact front and the reaction zone in the process lead to fluctuations of the detonation speed.

Heinrich, H. J.↗
NASA NTRS1961

ANALYSIS OF CRYOGENIC PROPELLANT FEED SYSTEMS FOR ELECTROTHERMAL ENGINES.

An analytical investigation was made of the problems associated with the long-term storage and control of flow of cryogenic propellants for electrothermal engines. Storage of 35 to 174 pounds of propellant for three years is made difficult by the high ratio of surface area to storage tank volume, and the resulting high rate of heat leak. Vented and non-vented storage, storage as high pressure gas, and the use of refrigeration were considered. Recommended storage methods are: for ethane and ammonia vented storage - by venting propellant stored in excess of mission requirements; for hydrogen and helium - by non-vented storage of cold supercritical vapor; and for methane by storage as a non-vented two-phase mixture. The optimum propellant density in the storage tank and optimum insulation thickness were also determined. Design charts were developed for hydrogen and helium, for estimating the maximum pressure expected in non-vented storage tanks, as function of mission requirements. Separation of the constituent phases of liquid-vapor mixtures is achieved by throttling the two-phase mixture to a lower pressure (and temperature) and vaporizing the liquid in the mixture by heat exchange with the contents of the storage tank. The time limitations for continuous use of this method are discussed. Linde super insulations SI-44 or SI -91 are recommended for insulation. Precooling the insulation to temperatures below the steady state level with cold helium vapor before or during fueling of the storage tank eliminates the flow of heat to the tank contents during countdown and take-off. The masses, sizes, and power requirements of the recommended systems are low. The controls are simple and reliable. From the equations and charts in this report the components of the system for a particular mission can be sized. Recommendations are given for experimental work required for the development and testing of such components.

ELECTROTHERMAL ENGINE↗
NASA NTRS1994

Archean geochemistry of formaldehyde and cyanide and the oligomerization of cyanohydrin

The sources and speciation of reduced carbon and nitrogen inferred for the early Archean are reviewed in terms of current observations and models, and known chemical reactions. Within this framework hydrogen cyanide and cyanide ion in significant concentration would have been eliminated by reaction with excess formaldehyde to form cyanohydrin (glycolonitrile), and with ferrous ion to formferrocyanide. Natural reactions of these molecules would under such conditions deserve special consideration in modeling of primordial organochemical processes. As a step in this direction, transformation reactions have been investigated involving glycolonitrile in the presence of water. We find that glycolonitrile, formed from formaldehyde and hydrogen cyanide or cyanide ion, spontaneously cyclodimerizes to 4-amino-2-hydroxymethyloxazole. The crystalline dimer is the major product at low temperatue (approximately 0 C); the yield diminishes with increasing temperature at the expense of polymerization and hydrolysis products. Hydrolysis of glycolamide and of oxazole yields a number of simpler organic molecules, including ammonia and glycolamide. The spontaneous polymerization of glycolonitrile and its dimer gives rise to soluble, cationic oligomers of as yet unknown structure, and, unless arrested, to a viscous liquid, insoluble in water. A loss of cyanide by reaction with formaldehyde, inferred for the early terrestrial hydrosphere and cryosphere would present a dilemma for hypotheses invoking cyanide and related compounds as concentrated reactants capable of forming biomolecular precursor species. Attempts to escape from its horns may take advantage of the efficient concentration and separation of cyanide as solid ferriferrocyanide, and most directly of reactions of glycolonitrile and its derivatives.

Arrhenius, T.↗
NASA NTRS2011

Views from EPOXI: Colors in Our Solar System as an Analog for Extrasolar Planets

The first visible-light studies of Earth-sized extrasolar planets will employ photometry or low-resolution spectroscopy. This work uses EPOCh medium-hand filter photometry between 150 and 950 nm obtained with the Deep Impact (DI) High Resolution Instrument (HRI) of Earth, the Moon, and Mars in addition to previous full-disk observations of the other six solar system planets and Titan to analyze the limitations of using photometric colors to characterize extrasolar planets. We determined that the HRI 350, 550, and 850 nm filters are optimal for distinguishing Earth from the other planets and separating planets to first order based on their atmospheric and surface properties. Detailed conclusions that can be drawn about exoplanet atmospheres simply from a color-color plot are limited due to potentially competing physical processes in the atmosphere. The presence of a Rayleigh scattering atmosphere can be detected by an increase in the 350-550 nm brightness ratio, but the absence of Rayleigh scattering cannot be confirmed due to the existence of atmospheric and surface absorbing species in the UV. Methane and ammonia are the only species responsible for strong absorption in the 850 nm filter in our solar system. The combination of physical processes present on extrasolar planets may differ from those we see locally. Nevertheless, a generation of telescopes capable of collecting such photometric observations can serve a critical role in first-order characterization and constraining the population of Earth-like extrasolar planets.

Crow, Carolyn A.↗
NASA NTRS2005

Fault-Tolerant Heat Exchanger

A compact, lightweight heat exchanger has been designed to be fault-tolerant in the sense that a single-point leak would not cause mixing of heat-transfer fluids. This particular heat exchanger is intended to be part of the temperature-regulation system for habitable modules of the International Space Station and to function with water and ammonia as the heat-transfer fluids. The basic fault-tolerant design is adaptable to other heat-transfer fluids and heat exchangers for applications in which mixing of heat-transfer fluids would pose toxic, explosive, or other hazards: Examples could include fuel/air heat exchangers for thermal management on aircraft, process heat exchangers in the cryogenic industry, and heat exchangers used in chemical processing. The reason this heat exchanger can tolerate a single-point leak is that the heat-transfer fluids are everywhere separated by a vented volume and at least two seals. The combination of fault tolerance, compactness, and light weight is implemented in a unique heat-exchanger core configuration: Each fluid passage is entirely surrounded by a vented region bridged by solid structures through which heat is conducted between the fluids. Precise, proprietary fabrication techniques make it possible to manufacture the vented regions and heat-conducting structures with very small dimensions to obtain a very large coefficient of heat transfer between the two fluids. A large heat-transfer coefficient favors compact design by making it possible to use a relatively small core for a given heat-transfer rate. Calculations and experiments have shown that in most respects, the fault-tolerant heat exchanger can be expected to equal or exceed the performance of the non-fault-tolerant heat exchanger that it is intended to supplant (see table). The only significant disadvantages are a slight weight penalty and a small decrease in the mass-specific heat transfer.

Izenson, Michael G.↗
NASA NTRS1998

Anion channels and the stimulation of anthocyanin accumulation by blue light in Arabidopsis seedlings

Activation of anion channels by blue light begins within seconds of irradiation in seedlings and is related to the ensuing growth inhibition. 5-Nitro-2-(3-phenylpropylamino)-benzoic acid (NPPB) is a potent, selective, and reversible blocker of these anion channels in Arabidopsis thaliana. Here we show that 20 microM NPPB blocked 72% of the blue-light-induced accumulation of anthocyanin pigments in seedlings. Feeding biosynthetic intermediates to wild-type and tt5 seedlings provided evidence that NPPB prevented blue light from up-regulating one or more steps between and including phenylalanine ammonia lyase and chalcone isomerase. NPPB was found to have no significant effect on the blue-light-induced increase in transcript levels of PAL1, CHS, CHI, or DFR, which are genes that encode anthocyanin-biosynthetic enzymes. Immunoblots revealed that NPPB also did not inhibit the accumulation of the chalcone synthase, chalcone isomerase, or flavanone-3-hydroxylase proteins. This is in contrast to the reduced anthocyanin accumulation displayed by a mutant lacking the HY4 blue-light receptor, as hy4 displayed reduced expression of the above enzymes. Taken together, the data indicate that blue light acting through HY4 leads to an increase in the amount of biosynthetic enzymes but blue light must also act through a separate, anion-channel-dependent system to create a fully functional biosynthetic pathway.

Non-NASA Center↗
NASA NTRS2017

Biologically Pre-Treated Habitation Waste Water as a Sustainable Green Urine Pre-Treat Solution

The ability to recover water from urine and flush water is a critical process to allow long term sustainable human habitation in space or bases on the moon or mars. Organic N present as urea or similar compounds can hydrolyze producing free ammonia. This reaction results in an increase in the pH converting ammonium to ammonia which is volatile and not removed by distillation. The increase in pH will also cause precipitation reactions to occur. In order to prevent this, urine on ISS is combined with a pretreat solution. While use of a pretreatment solution has been successful, there are numerous draw backs including: storage and use of highly hazardous solutions, limitations on water recovery (less than 85%), and production of brine with pore dewatering characteristics. We evaluated the use of biologically treated habitation wastewaters (ISS and early planetary base) to replace the current pretreat solution. We evaluated both amended and un-amended bioreactor effluent. For the amended effluent, we evaluated "green" pretreat chemicals including citric acid and citric acid amended with benzoic acid. We used a mock urine/air separator modeled after the urine collection assembly on ISS. The urine/air separator was challenged continually for >6 months. Depending on the test point, the separator was challenged daily with donated urine and flushed with amended or un-amended reactor effluent. We monitored the pH of the urine, flush solution and residual pH in the urine/air separator after each urine event. We also evaluated solids production and biological growth. Our results support the use of both un-amended and amended bioreactor effluent to maintain the operability of the urine /air separator. The ability to use bioreactor effluent could decrease consumable cost, reduce hazards associated with current pre-treat chemicals, allow other membrane based desalination processes to be utilized, and improve brine characteristics.

Jackson, W. Andrew↗
NASA NTRS2000

An Assessment of the Technical Readiness of the Vapor Phase Catalytic Ammonia Removal Process (VPCAR) Technology

This poster provides an assessment of the technical readiness of the Vapor Phase Catalytic Ammonia Removal Process (VPCAR). The VPCAR technology is a fully regenerative water recycling technology designed specifically for applications such as a near term Mars exploration mission. The VPCAR technology is a highly integrated distillation/catalytic oxidation based water processor. It is designed to accept a combined wastewater stream (urine, condensate, and hygiene) and produces potable water in a single process step which requires -no regularly scheduled re-supply or maintenance for a 3 year mission. The technology is designed to be modular and to fit into a volume comparable to a single International Space Station Rack (when sized for a crew of 6). This poster provides a description of the VPCAR technology and a summary of the current performance of the technology. Also provided are the results of two separate NASA sponsored system trade studies which investigated the potential payback of further development of the VPCAR technology.

Flynn, Michael↗
NASA NTRS2014

Solar Metal Sulfate-Ammonia Based Thermochemical Water Splitting Cycle for Hydrogen Production

Two classes of hybrid/thermochemical water splitting processes for the production of hydrogen and oxygen have been proposed based on (1) metal sulfate-ammonia cycles (2) metal pyrosulfate-ammonia cycles. Methods and systems for a metal sulfate MSO.sub.4--NH3 cycle for producing H2 and O2 from a closed system including feeding an aqueous (NH3)(4)SO3 solution into a photoctalytic reactor to oxidize the aqueous (NH3)(4)SO3 into aqueous (NH3)(2)SO4 and reduce water to hydrogen, mixing the resulting aqueous (NH3)(2)SO4 with metal oxide (e.g. ZnO) to form a slurry, heating the slurry of aqueous (NH4)(2)SO4 and ZnO(s) in the low temperature reactor to produce a gaseous mixture of NH3 and H2O and solid ZnSO4(s), heating solid ZnSO4 at a high temperature reactor to produce a gaseous mixture of SO2 and O2 and solid product ZnO, mixing the gaseous mixture of SO2 and O2 with an NH3 and H2O stream in an absorber to form aqueous (NH4)(2)SO3 solution and separate O2 for aqueous solution, recycling the resultant solution back to the photoreactor and sending ZnO to mix with aqueous (NH4)(2)SO4 solution to close the water splitting cycle wherein gaseous H2 and O2 are the only products output from the closed ZnSO4--NH3 cycle.

Huang, Cunping↗
NASA NTRS1993

Phylogeny of the ammonia-producing ruminal bacteria Peptostreptococcus anaerobius, Clostridium sticklandii, and Clostridium aminophilum sp. nov

In previous studies, gram-positive bacteria which grew rapidly with peptides or an amino acid as the sole energy source were isolated from bovine rumina. Three isolates, strains C, FT (T = type strain), and SR, were considered to be ecologically important since they produced up to 20-fold more ammonia than other ammonia-producing ruminal bacteria. On the basis of phenotypic criteria, the taxonomic position of these new isolates was uncertain. In this study, the 16S rRNA sequences of these isolates and related bacteria were determined to establish the phylogenetic positions of the organisms. The sequences of strains C, FT, and SR and reference strains of Peptostreptococcus anaerobius, Clostridium sticklandii, Clostridium coccoides, Clostridium aminovalericum, Acetomaculum ruminis, Clostridium leptum, Clostridium lituseburense, Clostridium acidiurici, and Clostridium barkeri were determined by using a modified Sanger dideoxy chain termination method. Strain C, a large coccus purported to belong to the genus Peptostreptococcus, was closely related to P. anaerobius, with a level of sequence similarity of 99.6%. Strain SR, a heat-resistant, short, rod-shaped organism, was closely related to C. sticklandii, with a level of sequence similarity of 99.9%. However, strain FT, a heat-resistant, pleomorphic, rod-shaped organism, was only distantly related to some clostridial species and P. anaerobius. On the basis of the sequence data, it was clear that strain FT warranted designation as a separate species. The closest known relative of strain FT was C. coccoides (level of similarity, only 90.6%). Additional strains that are phenotypically similar to strain FT were isolated in this study.(ABSTRACT TRUNCATED AT 250 WORDS).

NASA Program Exobiology↗
NASA NTRS1998

Galileo Probe Measurements of Thermal and Solar Radiation Fluxes in the Jovian Atmosphere

The Galileo probe net flux radiometer (NFR) measured radiation fluxes in Jupiter's atmosphere from about 0.44 to 14 bars, using five spectral channels to separate solar and thermal components. Onboard calibration results confirm that the NFR responded to radiation approximately as expected. NFR channels also responded to a superimposed thermal perturbation, which can be approximately removed using blind channel measurements and physical constraints. Evidence for the expected NH3 cloud was seen in the spectral character of spin-induced modulations of the direct solar beam signals. These results are consistent with an overlying cloud of small NH3 ice particles (0.5-0.75 microns in radius) of optical depth 1.5-2 at 0.5 microns. Such a cloud would have so little effect on thermal fluxes that NFR thermal channels provide no additional constraints on its properties. However, evidence for heating near 0.45 bar in the NFR thermal channels would seem to require either an additional opacity source beyond this small-particle cloud, implying a heterogeneous cloud structure to avoid conflicts with solar modulation results, or a change in temperature lapse rate just above the probe measurements. The large thermal flux levels imply water vapor mixing ratios that are only 6% of solar at 10 bars, but possibly increasing with depth, and significantly subsaturated ammonia at pressures less than 3 bars. If deep NH3 mixing ratios at the probe entry site are 3-4 times ground-based inferences, as suggested by probe radio signal attenuation, then only half as much water is needed to match NFR observations. No evidence of a water cloud was seen near the 5-bar level. The 5-microns thermal channel detected the presumed NH4SH cloud base near 1.35 bars. Effects of this cloud were also seen in the solar channel upflux measurements but not in the solar net fluxes, implying that the cloud is a conservative scatterer of sunlight. The minor thermal signature of this cloud is compatible with particle radii near 3 gm, but it cannot rule out smaller particles. Deeper than about 3 bars, solar channels indicate unexpectedly large absorption of sunlight at wavelengths longer than 0.6 microns, which might be due to unaccounted-for absorption by NH3 between 0.65 and 1.5 microns.

Sromovsky, L. A.↗
NASA NTRS2002

Miniature Heat Transport System for Spacecraft Thermal Control

Loop heat pipes (LHP) are efficient devices for heat transfer and use the basic principle of a closed evaporation-condensation cycle. The advantage of using a loop heat pipe over other conventional methods is that large quantities of heat can be transported through a small cross-sectional area over a considerable distance with no additional power input to the system. By using LHPs, it seems possible to meet the growing demand for high-power cooling devices. Although they are somewhat similar to conventional heat pipes, LHPs have a whole set of unique properties, such as low pressure drops and flexible lines between condenser and evaporator, that make them rather promising. LHPs are capable of providing a means of transporting heat over long distances with no input power other than the heat being transported because of the specially designed evaporator and the separation of liquid and vapor lines. For LHP design and fabrication, preliminary analysis on the basis of dimensionless criteria is necessary because of certain complicated phenomena that take place in the heat pipe. Modeling the performance of the LHP and miniaturizing its size are tasks and objectives of current research. In the course of h s work, the LHP and its components, including the evaporator (the most critical and complex part of the LHP), were modeled with the corresponding dimensionless groups also being investigated. Next, analysis of heat and mass transfer processes in the LHP, selection of the most weighted criteria from known dimensionless groups (thermal-fluid sciences), heat transfer rate limits, (heat pipe theory), and experimental ratios which are unique to a given heat pipe class are discussed. In the third part of the report, two-phase flow heat and mass transfer performances inside the LHP condenser are analyzed and calculated for Earth-normal gravity and microgravity conditions. On the basis of recent models and experimental databanks, an analysis for condensing two-phase flow regimes, pressure gradients, and local heat transfer coefficients using ammonia, propylene, and R134, are carried out.

Ochterbeck, Jay M.↗
NASA NTRS1998

Galileo Probe Measurements of Thermal and Solar Radiation Fluxes in the Jovian Atmosphere

The Galileo probe net flux radiometer (NFR) measured radiation fluxes in Jupiter's atmosphere from about 0.44 to 14 bars, using five spectral channels to separate solar and thermal components. Onboard calibration results confirm that the NFR responded to radiation approximately as expected. NFR channels also responded to a superimposed thermal perturbation, which can be approximately removed using blind channel measurements and physical constraints. Evidence for the expected NH3 cloud was seen in the spectral character of spin-induced modulations of the direct solar beam signals. These results are consistent with an overlying cloud of small NH3 ice particles (0.5-0.75 microns in radius) of optical depth 1.5-2 at 0.5 microns. Such a cloud would have so little effect on thermal fluxes that NFR thermal channels provide no additional constraints on its properties. However, evidence for heating near 0.45 bar in the NFR thermal channels would seem to require either an additional opacity source beyond this small-particle cloud, implying a heterogeneous-cloud structure to avoid conflicts with solar modulation results, or a change in temperature lapse rate just above the probe measurements. The large thermal flux levels imply water vapor mixing ratios that are only 6% of solar at 10 bars, but possibly increasing with depth, and significantly subsaturated ammonia at pressures less than 3 bars. If deep NH3 mixing ratios at the probe entry site are 3-4 times ground-based inferences, as suggested by probe radio signal attenuation, then only half as much water is needed to match NFR observations. No evidence of a water cloud was seen near the 5-bar level. The 5 microns thermal channel detected the presumed NH4SH cloud base near 1.35 bars. Effects of this cloud were also seen in the solar channel upflux measurements but not in the solar net fluxes, implying that the cloud is a conservative scatterer of sunlight. The minor thermal signature of this cloud is compatible with particle radii near 3 microns, but it cannot rule out smaller particles. Deeper than about 3 bars, solar channels indicate unexpectedly large absorption of sunlight at wavelengths longer than 0.6 microns, which might be due to unaccounted-for absorption by NH3 between 0.65 and 1.5 microns.

Sromovsky, L. A.↗
NASA NTRS2015

Testing of an Arcjet Thruster with Capability of Direct-Drive Operation

Electric thrusters typically require a power processing unit (PPU) to convert the spacecraft provided power to the voltage-current that a thruster needs for operation. Testing has been initiated to study whether an arcjet thruster can be operated directly with the power produced by solar arrays without any additional conversion. Elimination of the PPU significantly reduces system-level complexity of the propulsion system, and lowers developmental cost and risk. The work aims to identify and address technical questions related to power conditioning and noise suppression in the system and heating of the thruster in long-duration operation. The apparatus under investigation has a target power level from 400-1,000 W. However, the proposed direct-drive arcjet is potentially a highly scalable concept, applicable to solar-electric spacecraft with up to 100's of kW and beyond. A direct-drive electric propulsion system would be comprised of a thruster that operates with the power supplied directly from the power source (typically solar arrays) with no further power conditioning needed between those two components. Arcjet thrusters are electric propulsion devices, with the power supplied as a high current at low voltage; of all the different types of electric thruster, they are best suited for direct drive from solar arrays. One advantage of an arcjet over Hall or gridded ion thrusters is that for comparable power the arcjet is a much smaller device and can provide more thrust and orders of magnitude higher thrust density (approximately 1-10 N/sq m), albeit at lower I(sub sp) (approximately 800-1000 s). In addition, arcjets are capable of operating on a wide range of propellant options, having been demonstrated on H2, ammonia, N2, Ar, Kr, Xe, while present SOA Hall and ion thrusters are primarily limited to Xe propellant. Direct-drive is often discussed in terms of Hall thrusters, but they require 250-300 V for operation, which is difficult even with high-voltage solar arrays. The arcjet requires under 100 V, which is more in-line with what is easily possible with a solar array. Direct-drive of an electric propulsion system confers the advantage of reducing or eliminating the power processing unit (PPU) that is typically needed to convert the spacecraft-provided power to the voltage and current needed for thruster operation. Since the PPU is typically the most expensive piece of an electric thruster system, from both a fabrication and qualification standpoint, its elimination offers the potential for major reductions in system cost and risk. The design of the arcjet built for this effort was based on previous low power (1 kW class) arcjets. It has a precision machined 99.95% pure tungsten anode which also serves as the nozzle. The anode constrictor region is 1 mm (0.040-in) diameter and 1 mm (0.040-in) long. The cathode is a tungsten welding electrode doped with LaO2; its tip was precision ground to a 30◦ angle ending in a blunt end. The two electrodes are separated by a boron-nitride insulator which also serves as the propellant injection manifold; it ends in six small holes which introduce the propellant gas in the diverging section of the nozzle, directly adjacent to the cathode. The electrodes and insulator are housed in a stainless-steel outer-body, with a Macor insulator at the mid-plane to provide thermal isolation between the front and back halves of the device. The gas seals were made using Grafoil gaskets. Figure 1A shows the assembled thruster in the vacuum chamber; figure 1B shows the thruster in operation on argon at a flow rate of 676 sccm (20 mg/s). Initial testing was conducted in a 3.5-ft diameter vacuum chamber; the ultimate pressure reached during quasi-steady operation of the thruster was about 330 millitorr. The thruster was powered with a high-current, 0-100A, 15 kW power supply. The discharge was initiated with a high-voltage (approximately 10 kV) spark initiator that was isolated from the supply by a stack of diodes. The testing indicated that an operating point exists within the I-V characteristics that is compatible with direct-drive solar-electric operation; for a flow rate of 20 mg/s (argon) the arc could be sustained at a voltage of about 20 V and a current of 25 A (500W).

Martin, Adam K.↗
NASA NTRS1997

Observations and Modeling of the Transient General Circulation of the North Pacific Basin

The objective of this study was to clarify the role that interstellar-cloud chemistry played in forming the population of organic molecules presently found in carbonaceous meteorites. This goal was to be achieved by means of defining the isotopic components present in organic and related phases in the meteorites and thereby identify the processes and source reservoirs involved in organic synthesis in the early solar system. Isotopic analysis of separated amino acids from the Murchison meteorite yielded results that are complex and not fully interpretable at this time. Substantial inter-acid variability in D/H ratio was observed, some but not all of which could be attributed to exchange with terrestrial hydrogen. Pronounced, though smaller, variability was also found for N-15/N-14 ratios. For both D/H and N-15/N-14 data, observed meteoritic values were substantially greater than found in terrestrial materials, providing a robust constraint on degrees of possible terrestrial contamination. Also, C-13/C-12 ratios, though falling within the range of data found on earth, significantly exceeded those characteristic of naturally occurring terrestrial amino acids. Inter-acid variability in C-13/C-12 ratios was muted relative to that observed for D/H and N-15/N-14 but still lay well outside of experimental uncertainty. No systematic relationship could be observed between variations in H, C and N isotopes. Two anomalous components were also found during the course of this study. A highly (greater than 6% relative to terrestrial) N-15-depleted, N-rich compound, which has not yet been identified, co-eluted with some amino acids. Clearly the Murchison meteorite sampled nitrogen from a number of highly diverse isotopic reservoirs. In fact, from this and related studies, it is now apparent that the distribution of nitrogen isotopes in the primitive solar system was extremely inhomogeneous. The second anomalous result obtained in the present study was for an extract of 'ammonia' from Murchison. It should be noted that this sample consisted of ammonia that was probably derived from a number of different compounds present in the meteorite itself, possibly including amines and amides, as well as ammonia sensu strictu and ammonium slats. However, the significance of this analysis is that the N-15/N-14 ratio measured was much lower than those found for the meteoritic amino acids (+2% vs around + 9% relative to terrestrial). This raises an important question concerning the source of the ammonia that was involved in synthesis of the amino acids. This issue needs to be explored further.

Kerridge, John F.↗
NASA NTRS2002

Trends in lignin modification: a comprehensive analysis of the effects of genetic manipulations/mutations on lignification and vascular integrity

A comprehensive assessment of lignin configuration in transgenic and mutant plants is long overdue. This review thus undertook the systematic analysis of trends manifested through genetic and mutational manipulations of the various steps associated with monolignol biosynthesis; this included consideration of the downstream effects on organized lignin assembly in the various cell types, on vascular function/integrity, and on plant growth and development. As previously noted for dirigent protein (homologs), distinct and sophisticated monolignol forming metabolic networks were operative in various cell types, tissues and organs, and form the cell-specific guaiacyl (G) and guaiacyl-syringyl (G-S) enriched lignin biopolymers, respectively. Regardless of cell type undergoing lignification, carbon allocation to the different monolignol pools is apparently determined by a combination of phenylalanine availability and cinnamate-4-hydroxylase/"p-coumarate-3-hydroxylase" (C4H/C3H) activities, as revealed by transcriptional and metabolic profiling. Downregulation of either phenylalanine ammonia lyase or cinnamate-4-hydroxylase thus predictably results in reduced lignin levels and impaired vascular integrity, as well as affecting related (phenylpropanoid-dependent) metabolism. Depletion of C3H activity also results in reduced lignin deposition, albeit with the latter being derived only from hydroxyphenyl (H) units, due to both the guaiacyl (G) and syringyl (S) pathways being blocked. Apparently the cells affected are unable to compensate for reduced G/S levels by increasing the amounts of H-components. The downstream metabolic networks for G-lignin enriched formation in both angiosperms and gymnosperms utilize specific cinnamoyl CoA O-methyltransferase (CCOMT), 4-coumarate:CoA ligase (4CL), cinnamoyl CoA reductase (CCR) and cinnamyl alcohol dehydrogenase (CAD) isoforms: however, these steps neither affect carbon allocation nor H/G designations, this being determined by C4H/C3H activities. Such enzymes thus fulfill subsidiary processing roles, with all (except CCOMT) apparently being bifunctional for both H and G substrates. Their severe downregulation does, however, predictably result in impaired monolignol biosynthesis, reduced lignin deposition/vascular integrity, (upstream) metabolite build-up and/or shunt pathway metabolism. There was no evidence for an alternative acid/ester O-methyltransferase (AEOMT) being involved in lignin biosynthesis.The G/S lignin pathway networks are operative in specific cell types in angiosperms and employ two additional biosynthetic steps to afford the corresponding S components, i.e. through introduction of an hydroxyl group at C-5 and its subsequent O-methylation. [These enzymes were originally classified as ferulate-5-hydroxylase (F5H) and caffeate O-methyltransferase (COMT), respectively.] As before, neither step has apparently any role in carbon allocation to the pathway; hence their individual downregulation/manipulation, respectively, gives either a G enriched lignin or formation of the well-known S-deficient bm3 "lignin" mutant, with cell walls of impaired vascular integrity. In the latter case, COMT downregulation/mutation apparently results in utilization of the isoelectronic 5-hydroxyconiferyl alcohol species albeit in an unsuccessful attempt to form G-S lignin proper. However, there is apparently no effect on overall G content, thereby indicating that deposition of both G and S moieties in the G/S lignin forming cells are kept spatially, and presumably temporally, fully separate. Downregulation/mutation of further downstream steps in the G/S network [i.e. utilizing 4CL, CCR and CAD isoforms] gives predictable effects in terms of their subsidiary processing roles: while severe downregulation of 4CL gave phenotypes with impaired vascular integrity due to reduced monolignol supply, there was no evidence in support of increased growth and/or enhanced cellulose biosynthesis. CCR and CAD downregulation/mutations also established that a depletion in monolignol supply reduced both lignin contents supply reduced both lignin contents and vascular integrity, with a concomitant shift towards (upstream) metabolite build-up and/or shunting.The extraordinary claims of involvement of surrogate monomers (2-methoxybenzaldehyde, feruloyl tyramine, vanillic acid, etc.) in lignification were fully disproven and put to rest, with the investigators themselves having largely retracted former claims. Furthermore analysis of the well-known bm1 mutation, a presumed CAD disrupted system, apparently revealed that both G and S lignin components were reduced. This seems to imply that there is no monolignol specific dehydrogenase, such as the recently described sinapyl alcohol dehydrogenase (SAD) for sinapyl alcohol formation. Nevertheless, different CAD isoforms of differing homology seem to be operative in different lignifying cell types, thereby giving the G-enriched and G/S-enriched lignin biopolymers, respectively. For the G-lignin forming network, however, the CAD isoform is apparently catalytically less efficient with all three monolignols than that additionally associated with the corresponding G/S lignin forming network(s), which can more efficiently use all three monolignols. However, since CAD does not determine either H, G, or S designation, it again serves in a subsidiary role-albeit using different isoforms for different cell wall developmental and cell wall type responses.The results from this analysis contrasts further with speculations of some early investigators, who had viewed lignin assembly as resulting from non-specific oxidative coupling of monolignols and subsequent random polymerization. At that time, though, the study of the complex biological (biochemical) process of lignin assembly had begun without any of the (bio)chemical tools to either address or answer the questions posed as to how its formation might actually occur. Today, by contrast, there is growing recognition of both sophisticated and differential control of monolignol biosynthetic networks in different cell types, which serve to underscore the fact that complexity of assembly need not be confused any further with random formation. Moreover, this analysis revealed another factor which continues to cloud interpretations of lignin downregulation/mutational analyses, namely the serious technical problems associated with all aspects of lignin characterization, whether for lignin quantification, isolation of lignin-enriched preparations and/or in determining monomeric compositions. For example, in the latter analyses, some 50-90% of the lignin components still cannot be detected using current methodologies, e.g. by thioacidolysis cleavage and nitrobenzene oxidative cleavage. This deficiency in lignin characterization thus represents one of the major hurdles remaining in delineating how lignin assembly (in distinct cell types) and their configuration actually occurs.

Review, Academic↗