Search NASA⌕ Search

SEARCH · Search NASA

Results for “auxiliary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Preliminary design study of hydrogen and ammonia resistojets for prime and auxiliary thrusters

Designs of high performance resistojets for primary and auxiliary propulsion are described.Thruster power for the primary propulsion application was in the 2 to 3 kW range while auxiliary propulsion power per thruster was 0.15 to 0.25 kW. Propellants considered were hydrogen and ammonia. The report described design techniques used to forecast the temperature and energy flux distributions using mathematical modeling by personal microcomputer. BASIC language is used throughout to give the designer rapid interaction and control. Both designs integrate compact first stage coils with concentric tubular heaters. The hybrid heater design allows better thruster power matching with the spacecraft power bus. Projected specific impulse levels were 760 to 830 s for hydrogen and 380 to 410 s for ammonia.

Page, Russell J.↗
NASA NTRS1988

A test for spatial clustering in the presence of auxiliary information

A technique is proposed to test for the presence of clusters when both spatial and auxiliary information is available. The test is based on randomizing the auxiliary information over the spatial locations. It requires no model assumptions (such as a Poisson process) for the spatial distribution. The procedure may be used to screen data for possible clustering.

Banfield, Jeff↗
NASA NTRS1956

Investigation at supersonic and subsonic Mach numbers of auxiliary inlets supplying secondary air flow to ejector exhaust nozzles

The results indicated increases in auxiliary-inlet pressure recovery with increases in scoop height relative to the boundary-layer thickness. The pressure recovery increased at about the same rate as theoretically predicted for an inlet in a boundary layer having a one-seventh power profile, but was only about 0.68 to 0.75 of the theoretically obtainable values. Under some operating conditions, flow from the primary jet was exhausted through the auxiliary inlet. This phenomenon could be predicted from the ejector pumping characteristics.

Hearth, Donald P↗
NASA NTRS1955

Preliminary Investigation of a Conical Spike Inlet in Combination with a Vertical-wedge Auxiliary Inlet at Mach Number 1.9

Pressure-recovery characteristics of a nacelle-type-spike inlet in combination with a vertical-wedge auxiliary scoop are presented for a free-stream Mach number of 1.9 at zero angle of attack. The auxiliary scoop provided 17 percent additional air flow with a drop in critical pressure recovery from 0.86 to 0.81. However, in terms of inlet-engine matching, the pressure recovery of the undersized spike inlet operating at a specified corrected air flow increased with the scoop open, for example, from 0.69 to 0.81.

Beke, Andrew↗
NASA NTRS1934

Wind-tunnel tests on combinations of a wing with fixed auxiliary airfoils having various chords and profiles

This report presents the results of wind tunnel tests on various auxiliary airfoils having three different airfoil sections and several different chord lengths in combination with a Clark y model wing in a sufficient number of relative positions to determine the optimum with regard to certain criterions of aerodynamic performance. The airfoil sections included a symmetrical profile, one of medium camber, and a highly cambered one. The chord sizes of the auxiliary airfoils ranged from 7.5 to 25 percent of the chord of the main wing, and the span was equal to that of the main wing.

Weick, Fred E↗
NASA NTRS1958

X-15 auxiliary power units and reaction controls

Electrical and hydraulic power within the X-15 airplane is developed by a monopropellant auxiliary power unit. In addition, airplane altitude control at extreme altitude is by monopropellant rockets. Two duplicate installations are used to provide reliability beyond single-system capabilities to assure continuous availability of aerodynamic flight controls and space-altitude controls. All components have been developed and evaluation tested by the individual suppliers. The principal item, the auxiliary power unit, has completed a 150 hour endurance test comprising 300 typical mission duty cycles. (author)

Wagner, Bruce O↗
NASA NTRS1992

Synchronous dynamics of a coupled shaft/bearing/housing system with auxiliary support from a clearance bearing: Analysis and experiment

This study examines the response of a flexible rotor supported by load sharing between linear bearings and an auxiliary clearance bearing. The objective of the work is to develop a better understanding of the dynamical behavior of a magnetic bearing supported rotor system interacting with auxiliary bearings during a critical operating condition. Of particular interest is the effect of coupling between the bearing/housing and shaft vibration on the rotordynamical responses. A simulation model is developed and a number of studies are performed for various parametric configurations. An experimental investigation is also conducted to compare and verify the rotordynamic behavior predicted by the simulation studies. A strategy for reducing synchronous shaft vibration through appropriate design of coupled shaft/bearing/housing vibration modes is identified. The results are presented and discussed.

Lawen, James, Jr.↗
NASA NTRS1995

Probabilistic risk assessment of the Space Shuttle. Phase 3: A study of the potential of losing the vehicle during nominal operation. Volume 5: Auxiliary shuttle risk analyses

Volume 5 is Appendix C, Auxiliary Shuttle Risk Analyses, and contains the following reports: Probabilistic Risk Assessment of Space Shuttle Phase 1 - Space Shuttle Catastrophic Failure Frequency Final Report; Risk Analysis Applied to the Space Shuttle Main Engine - Demonstration Project for the Main Combustion Chamber Risk Assessment; An Investigation of the Risk Implications of Space Shuttle Solid Rocket Booster Chamber Pressure Excursions; Safety of the Thermal Protection System of the Space Shuttle Orbiter - Quantitative Analysis and Organizational Factors; Space Shuttle Main Propulsion Pressurization System Probabilistic Risk Assessment, Final Report; and Space Shuttle Probabilistic Risk Assessment Proof-of-Concept Study - Auxiliary Power Unit and Hydraulic Power Unit Analysis Report.

Fragola, Joseph R.↗
NASA NTRS1995

Steady-state dynamic behavior of an auxiliary bearing supported rotor system

This paper investigates the steady-state responses of a rotor system supported by auxiliary bearings in which there is a clearance between the rotor and the inner race of the bearing. A simulation model based upon the rotor of a production jet engine is developed and its steady-state behavior is explored over a wide range of operating conditions for various parametric configurations. Specifically, the influence of rotor imbalance, support stiffness, and damping is studied. It is found that imbalance may change the rotor responses dramatically in terms of frequency contents at certain operating speeds. Subharmonic responses of 2nd order through 10th order are all observed except the 9th order. Chaotic phenomenon is also observed. Jump phenomena (or double-valued responses) of both hard-spring type and soft-spring type are shown to occur at low operating speeds for systems with low auxiliary bearing damping or large clearance even with relatively small imbalance. The effect of friction between the shaft and the inner race of the bearing is also discussed.

Xie, Huajun↗
NASA NTRS1995

Synchronous dynamics of a coupled shaft/bearing/housing system with auxiliary support from a clearance bearing: Analysis and experiment

This study examines the response of a flexible rotor supported by load sharing between linear bearings and an auxiliary clearance bearing. The objective is to develop a better understanding of the dynamical behavior of a magnetic bearing supported rotor system interacting with auxiliary bearings during a critical operating condition. Of particular interest is the effect of coupling between the bearing/housing and shaft vibration on the rotordynamical responses. A simulation model is developed and a number of studies are performed for various parametric configurations. An experimental investigation is also conducted to compare and verify the rotordynamic behavior predicted by the simulation studies. A strategy for reducing synchronous shaft vibration through appropriate design of coupled shaft/bearing/housing vibration modes is identified.

Lawen, James L., Jr.↗
NASA NTRS1959

Investigation of a 4.5-Inch-Mean-Diameter Two-Stage Axial-Flow Turbine Suitable for Auxiliary Power Drives

The design and experimental investigation of a 4.5-inch-mean-diameter two-stage turbine are presented herein and used to study the effect of size on the efficiency of turbines in the auxiliary power drive class. The results of the experimental investigation indicated that design specific work was obtained at design speed at a total-to-static efficiency of 0.639. At design pressure ratio, design static-pressure distribution through the turbine was obtained with an equivalent specific work output of 33.2 Btu per pound and an efficiency of 0.656. It was found that, in the design of turbines in the auxiliary power drive class, Reynolds number plays an important part in the selection of the design efficiency. Comparison with theoretical efficiencies based on a loss coefficient and velocity diagrams are presented. Close agreement was obtained between theory and experiment when the loss coefficient was adjusted for changes in Reynolds number to the -1/5 power.

Wong, Robert Y.↗
NASA NTRS1959

The Total-Pressure Recovery and Drag Characteristics of Several Auxiliary Inlets at Transonic Speeds

Several flush and scoop-type auxiliary inlets have been tested for a range of Mach numbers from 0.55 to 1.3 to determine their transonic total-pressure recovery and drag characteristics. The inlet dimensions were comparable with the thickness of the boundary layer in which they were tested. Results indicate that flush inlets should be inclined at very shallow angles with respect to the surface for optimum total-pressure recovery and drag characteristics. Deep, narrow inlets have lower drag than wide shallow ones at Mach numbers greater than 0.9 but at lower Mach numbers the wider inlets proved superior. Inlets with a shallow approach ramp, 7 deg, and diverging ramp walls which incorporated boundary-layer bypass had lower drag than any other inlet tested for Mach numbers up to 1.2 and had the highest pressure recovery of all of the flush inlets. The scoop inlets, which operated in a higher velocity flow than the flush inlets, had higher drag coefficients. Several of these auxiliary inlets projected multiple, periodic shock waves into the stream when they were operated at low mass-flow ratios.

Dennard, John S.↗
NASA NTRS1946

Effect of an Auxiliary Belly Fuel Tank on the Low-Speed Static Stability Characteristics of a 1/5-Scale Model of the Grumman XF8F-1 Airplane, TED No. NACA 2384

In.order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a l/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank. It was found that, at low speed, the auxiliary fuel tank test conditions, especially with power on in the landing configuration at high lift coefficients. The static directional stability was decreased for most test conditions, but the addition of a fairing between the fuselage and fuel tank improved the directional stability slightly in the power-on clean condition. The effective dihedral and lateral force were increased for most of the conditions tested. The tuft studies and pressure measurements indicated that the removal of the away braces would improve the.flow characteristics considerably in the region of the fuel tank end might also decrease the buffeting of the belly tank at high speeds.

Cook, Charles B.↗
NASA NTRS1938

Wind-Tunnel Investigation of an N.A.C.A. 23012 Airfoil with a Slotted Flap and Three Types of Auxiliary Flap

An investigation was made in the N.A.C.A. 7- by 10- foot wind tunnel to determine the aerodynamic section characteristics of an N. A. C. A. 23012 airfoil with a single main slotted flap equipped successively with auxiliary flaps of the plain, split, and slotted types. A test installation mas used in which an airfoil of 7-foot span was mounted vertically between the upper and the lower sides of the closed test section so that two-dimensional flow was approximated. On the basis of maximum lift coefficient, low drag at moderate and high lift coefficients, and high drag at high lift coefficients, the optimum combination of the arrangements was found to be the double slotted flap . All the auxiliary flaps tested, however, increased the magnitudes of the pitching moments over those of the main slotted flap alone.

Wenzinger, Carl J.↗
NASA NTRS1962

Study of Umbrella-Type Erectable Paraboloidal Solar Concentrators for Generation of Spacecraft Auxiliary Power

An investigation was made of some aspects of erectable umbrella-type paraboloidal solar-energy concentrators for use in spacecraft auxiliary power systems. An analysis is presented for the design of concentrators employing radial ribs and membrane-type coverings. The rib stiffness necessary to give a desired parabolic curvature upon erection is determined. Rib contour measurements were made in an upright and inverted position on an experimental 10-foot-diameter concentrator giving a focal length of 30.78 inches and 30.6 inches, respectively, as compared with a design focal length of 30 inches. Calorimetric tests employing spherical heat receivers showed a maximum geometrical concentrator efficiency of 75.3 percent with a concentration ratio of 92.2 at a focal length of approximately 30.5 inches. Within the scope of this investigation, it was found that, as the concentrator size increases, the weight per unit projected area increases, time to damp to one-half amplitude increases, and the natural frequency decreases. Umbrella-type solar concentrators appear to be feasible for power conversion systems using low concentration ratios; however, for large concentrators the time required to damp out disturbances may be a problem.

SPACECRAFT↗