SEARCH · Search NASA

Results for “base bleeding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1991

Aerodynamic control using forebody blowing and suction

Aerodynamic control using pneumatic forebody flow control was studied. Three methods of control were investigated: (1) blowing from a localized jet, (2) blowing from a slot, and (3) surface suction. Flow visualization and yawing moment measurements were performed on F/A-18 models in a water tunnel. The results show that all the methods were effective in controlling the forebody flow over a wide range of angles of attack and sideslip. The advantages and limitations of each of the control methods were discussed. The experiments suggested that all the control methods work basically on the principle of separation control. Based on the results of the water tunnel tests, the blowing or suction mass flow requirements appear to be within the limits of typical engine-bleed available from a modern fighter engine.

Ng, T. Terry↗

NASA NTRS1984

Numerical simulation of flow through inlets/diffusers with terminal shocks

Two-dimensional Euler and Navier-Stokes solutions of the flow through three inlet/diffuser configurations with terminal shock systems are reported. Calculations without bleed indicate that the terminal shock location is very sensitive to the outflow back pressure. For cases where there are no available experimental results, it becomes difficult to estimate the back pressure that will result in a terminal shock. Estimates based on quasi-one-dimensional analysis are not found adequate for complex two-dimensional flows. It is found that since the flow downstream of the terminal shock is subsonic, and what happens at the outflow boundary affects the flow inside the inlet, enough of the subsonic diffuser must be modeled to accurately predict the terminal shock region. The diffuser portion should be fairly long with the outflow boundary occurring in a region of more or less uniform flow to be able to prescribe a uniform back pressure. The third configuration studied was investigated with and without incorporating bleed in the code. It is found that the use of bleed stabilizes the shock location and allows solutions which without bleed result in unstarting of the inlet. Comparisons are made with available experimental data.

Talcott, N. A., Jr.↗

NASA NTRS1985

Overview of solid particle LV seeding techniques used at UTRC

Due to the failure of existing seeders to meet the stringent specifications required for benchmark experiments in high pressure, high temperature, rapidly accelerating flowfields, an effort is made to improve an existing solid particle seeder. The goal is to produce a more monodisperse seed from the 0.3 micro alumina powder with more than 99 percent of the particles in the submicron range while maintaining a high seeding rate. Coiled-wire inserts are installed within the ends of the nitrogen injection lines in the primary seeder to produce swirling conical jets to vigorously agitate the seed bed. A secondary swirler, constructed from a 25 cm length of 3.8 cm ID steel pipe having threaded end caps, is connected to the output line of the primary seeder. The seeded nitrogen from the primary seeder is injected tangentially at near sonic velocity into the secondary swirler 9.4 cm above its base. Independently controlled auxiliary nitrogen used to increase the swirl in the secondary chamber is also injected tangentially 2.5 cm below the seeded nitrogen lines. Large seed particles are collected by bleeds in the swirler cap and directed overboard. The remaining seeded nitrogen is collected on the center line of the secondary swirler and ducted to the rig.

Patrick, W. P.↗

NASA NTRS1992

Bleed-boundary conditions for numerically simulated mixed-compression supersonic inlet flow

A numerical study was performed to investigate boundary conditions for bleed openings that are needed in the numerical simulation of critical flow through turbojet inlets with bleed. Nine different boundary conditions (BCs) were devised and examined. Of the BCs examined, three were able to stabilize the terminal shock near the inlet's throat. This numerical study was based on the ensemble-averaged, unsteady, three-dimensional, compressible Navier-Stokes equations closed by the Baldwin-Lomax algebraic turbulence model. Solutions to the Navier-Stokes equations were obtained by using a hybrid implicit-explicit method (Beam and Warming/MacCormack). The multiblock grid system used in the solution procedure was generated by solving a set of elliptic partial differential equations. Solutions obtained were compared with available experimental data.

Chyu, W. J.↗

NASA NTRS2005

Two Stage Supersonic Inlet (TSSI):10-inch Model Calculations

The bifurcated inlet examined in this study (which is one of several being considered in the High Speed Research (HSR) Program) was chosen based upon paper trade studies of axisymmetric, single sided, and bifurcated inlets. For a given compression ratio and mass flow a bifurcated inlet weighs less than a single sided inlet. An axisymmetric inlet has less bleed requirements than 2D inlets but has trouble matching transonic airflow requirements without going to a variable diameter centerbody. The bifurcated inlet was selected as one of the candidates because of its ability to match airflow schedules. The inlet examined in this study, the Two Stage Supersonic Inlet (TSSI), was a candidate mixed compression bifurcated inlet. It has a novel concept to aid in inlet stability. This concept was tested in the 10x10 wind tunnel at NASA Glenn. CFD tools were used to predict and interpret the experimental results.

Chapman, Dave↗

NASA NTRS2017

A Dynamic Model for the Evaluation of Aircraft Engine Icing Detection and Control-Based Mitigation Strategies

Aircraft flying in regions of high ice crystal concentrations are susceptible to the buildup of ice within the compression system of their gas turbine engines. This ice buildup can restrict engine airflow and cause an uncommanded loss of thrust, also known as engine rollback, which poses a potential safety hazard. The aviation community is conducting research to understand this phenomena, and to identify avoidance and mitigation strategies to address the concern. To support this research, a dynamic turbofan engine model has been created to enable the development and evaluation of engine icing detection and control-based mitigation strategies. This model captures the dynamic engine response due to high ice water ingestion and the buildup of ice blockage in the engines low pressure compressor. It includes a fuel control system allowing engine closed-loop control effects during engine icing events to be emulated. The model also includes bleed air valve and horsepower extraction actuators that, when modulated, change overall engine operating performance. This system-level model has been developed and compared against test data acquired from an aircraft turbofan engine undergoing engine icing studies in an altitude test facility and also against outputs from the manufacturers customer deck. This paper will describe the model and show results of its dynamic response under open-loop and closed-loop control operating scenarios in the presence of ice blockage buildup compared against engine test cell data. Planned follow-on use of the model for the development and evaluation of icing detection and control-based mitigation strategies will also be discussed. The intent is to combine the model and control mitigation logic with an engine icing risk calculation tool capable of predicting the risk of engine icing based on current operating conditions. Upon detection of an operating region of risk for engine icing events, the control mitigation logic will seek to change the engines operating point to a region of lower risk through the modulation of available control actuators while maintaining the desired engine thrust output. Follow-on work will assess the feasibility and effectiveness of such control-based mitigation strategies.

engine control↗

NASA NTRS2017

A Dynamic Model for the Evaluation of Aircraft Engine Icing Detection and Control-Based Mitigation Strategies

engine control↗

NASA NTRS1980

Design of a multivariable integrated control for a supersonic propulsion system

An inlet/engine/nozzle integrated control mode for the propulsion system of an advanced supersonic commercial aircraft was studied. Results show that integration of these control functions can result in both operational and performance benefits for the propulsion system. For example, this integrated control mode may make it possible to minimize the use of inlet bypass doors for shock position control. This may be of benefit to the aircraft as a result of minimizing: (1) bypass bleed drag effects; (2) perturbations to the aircraft resulting from the side thrust effect of the bypass bleeds; and (3) potential unstarts of the inlet. A conceptual integrated control mode was developed which makes use of many cross coupling paths between inlet and engine control variables and inlet and engine sensed variables. A multivariable control design technique based upon linear quadratic regulator theory was applied to designing the feedback gains for this control to allow a simulation evaluation of the benefits of the integrated control mode.

Beattie, E. C.↗

NASA NTRS1984

Backup control airstart performance on a digital electronic engine control-equipped F100-engine

The air start capability of a backup control (BUC) was tested for a digital electronic engine control (DEEC) equipped F100 engine, which was installed in an F-15 aircraft. Two air start schedules were tested. Using the group 1 start schedule, based on a 40 sec timer, an air speed of 300 knots was required to ensure successful 40 and 25% BUC mode spooldown airstarts. If core rotor speed (N2) was less than 40% a stall would occur when the start bleed closed, 40 sec after initiation of the air start. All jet fuel starter (JFS) assisted air starts were successful with the group 1 start schedule. For the group 2 schedule, the time between pressurization and start bleed closure ranged between 50 sec and 72 sec. Idle rps was lower than the desired 65% for air starts at higher altitudes and lower air speeds.

Johnson, J. B.↗

NASA NTRS1989

Flight/propulsion control integration for V/STOL fighter/attack aircraft

A NASA-defined technology program investigating integrated flight/propulsion control system design for vertical and short takeoff and landing (V/STOL) aircraft is outlined, and initial fixed-base simulation experiments for two V/STOL aircraft are covered. It is shown that transition performance can be characterized by the minimum climb or level-flight acceleration that can be achieved. Level-1 flying qualities can be achieved for deceleration to hover in instrument conditions, and for shore-based and shipboard landing when attitude and velocity stabilization and command augmentation modes are provided. Level-1 and Level-2 flying qualities can be expected when only attitude command is provided. During vertical landing aboard a destroyer in heavy seas, substantial bleed flow rates are reported for a control arrangement employing reaction control for the pitch, roll, and yaw axes. Peak bleed flows can be reduced for a control arrangement using lateral-thrust transfer for roll control.

Franklin, James A.↗

NASA NTRS1959

Exploratory Investigation of the Effects of Boundary-Layer Control on the Pressure-Recovery Characteristics of a Circular Internal-Contraction Inlet with Translating Centerbody at Mach Numbers of 2.00 and 2.35

Exploratory tests of a circular internal-contraction inlet were made at Mach numbers of 2.00 and 2.35 to determine the effect of a cowl-type boundary-layer control located downstream of the inlet throat. The inlet was designed for a Mach number of 2.5. Tests were also made of the inlet modified to correspond to design Mach numbers of 2.35 and 2.25. Surveys near the minimum area section of the inlet without boundary-layer control indicated maximum averaged pressure recoveries between 0.90 and 0.92 at a free-stream Mach number, M(sub infinity), of 2.35 for the inlets. Farther downstream, after partial subsonic diffusion, a maximum pressure recovery of 0.842 was obtained with the inlet at M(sub infinity) = 2.35. The pressure recovery of the inlet was increased by 0.03 at a Mach number of 2.35 and decreased by 0.02 at a Mach number of 2.00 by the application of cowl-type boundary-layer control. Further investigation with the inlet without bleed demonstrated that an increase of angle of attack from 0 deg to 3 deg reduced the pressure recovery 0.04. The effect of Reynolds number was to increase pressure recovery 0.07 (from 0.785 to 0.855) with an increase in Reynolds number (based on inlet diameter) from 0.79 x 10(exp 6) to 3.19 x 10(exp 6).

Martin, Norman J.↗

NASA NTRS2006

Microwave Blade Tip Clearance System: An Update

Newer engines use compressor bleed air and a model to close clearances open loop. Measuring clearances and closing the control loop can add additional efficiencies. Tip clearance control has been identified as a key technology for future engines Additional benefits in prognostics, NSMS, and condition-based maintenance. In the HPT for every 1 mil improvement in clearance: a) SFC decreases 0.1%; and b) EGT margin increases 1 C.

Geisheimer, Jon↗

DOE OSTI2026

Flowable Cementitious Grouts for False Bottoms in Hanford Waste Tanks – 26085

Cementitious grouts with epoxy coatings are being evaluated as an approach to refurbish the bottom of waste tanks at the Hanford Site. This work studies four grout concept materials for this application, two grouts being from commercial vendors and two grouts based off formulations used to close reactors and tanks at the Savannah River Site. All the candidate grouts demonstrate flowability and pumpability at the 0.5 cu ft scale. The commercial vendor products demonstrate the best flow and have lower water/premix ratio and are less likely to have bleed, which would impact epoxy bonding to the grout. The commercial products also demonstrate increased compression strengths compared to the reactor closure grouts. Additional fresh and cured properties for all the grout formulations were similar. The grouts in the tank waste simulant without epoxy coating do not crack but show visual changes to the grout and the surrounding simulant solution, and simulant absorption into the grout. The grout/epoxy bond in ambient conditions has strengths of over 7 MPa and needs to be evaluated for simulant chemical durability. Overall, the results to date justify testing the flowability, pumpability, and placement of the grouts at larger, engineering scale and for further studies of the interactions between the grout and epoxy.

Valdes, Nicholas [Savannah River National Laborato↗

NASA NTRS1991

Supersonic propulsion simulation by incorporating component models in the large perturbation inlet (LAPIN) computer code

An approach to simulating the internal flows of supersonic propulsion systems is presented. The approach is based on a fairly simple modification of the Large Perturbation Inlet (LAPIN) computer code. LAPIN uses a quasi-one dimensional, inviscid, unsteady formulation of the continuity, momentum, and energy equations. The equations are solved using a shock capturing, finite difference algorithm. The original code, developed for simulating supersonic inlets, includes engineering models of unstart/restart, bleed, bypass, and variable duct geometry, by means of source terms in the equations. The source terms also provide a mechanism for incorporating, with the inlet, propulsion system components such as compressor stages, combustors, and turbine stages. This requires each component to be distributed axially over a number of grid points. Because of the distributed nature of such components, this representation should be more accurate than a lumped parameter model. Components can be modeled by performance map(s), which in turn are used to compute the source terms. The general approach is described. Then, simulation of a compressor/fan stage is discussed to show the approach in detail.

Cole, Gary L.↗

NASA NTRS2017

Acoustic Detection of Faults and Degradation in a High-Bypass Turbofan Engine during VIPR Phase III Testing

The Vehicle Integrated Propulsion Research (VIPR) Phase III project was executed at Edwards Air Force Base, California, by the National Aeronautics and Space Administration and several industry, academic, and government partners in the summer of 2015. One of the research objectives was to use external radial acoustic microphone arrays to detect changes in the noise characteristics produced by the research engine during volcanic ash ingestion and seeded fault insertion scenarios involving bleed air valves. Preliminary results indicate the successful acoustic detection of suspected degradation as a result of cumulative exposure to volcanic ash. This detection is shown through progressive changes, particularly in the high-frequency content, as a function of exposure to greater cumulative quantities of ash. Additionally, detection of the simulated failure of the 14th stage stability bleed valve and, to a lesser extent, the station 2.5 stability bleed valve, to their fully-open fail-safe positions was achieved by means of spectral comparisons between nominal (normal valve operation) and seeded fault scenarios.

noise spectra↗

NASA NTRS1975

Preliminary study of advanced turbofans for low energy consumption

This analysis determines the effect of higher overall engine pressure ratios (OPR's), bypass ratios (BPR's), and turbine rotor-inlet temperature on a Mach-0.85 transport having a range of 5556 km (3000 nmi) and carrying a payload of 18144 kg (40,000 lbs-200 passengers). Sideline noises (jet plus fan) of between 91 and 106 EPNdB (FAR36) are considered. Takeoff gross weight (TOGW), fuel consumption (kg/pass. km) and direct operating cost (DOC) are used at the figures of merit. Based on predicted 1985 levels of engine technology and a noise goal of 96 EPNdB, the higher-OPR engine results in an airplane that is 18 percent lighter in terms of TOGW, uses 22.3 percent less fuel, and has a 14.7 percent lower DOC than a comparable airplane powered by a current turbofan. Cooling the compressor bleed air and lowering the cruise Mach number appear attractive in terms of further improving the figures of merit.

Knip, G.↗

NASA NTRS1996

User Interface Developed for Controls/CFD Interdisciplinary Research

The NASA Lewis Research Center, in conjunction with the University of Akron, is developing analytical methods and software tools to create a cross-discipline "bridge" between controls and computational fluid dynamics (CFD) technologies. Traditionally, the controls analyst has used simulations based on large lumping techniques to generate low-order linear models convenient for designing propulsion system controls. For complex, high-speed vehicles such as the High Speed Civil Transport (HSCT), simulations based on CFD methods are required to capture the relevant flow physics. The use of CFD should also help reduce the development time and costs associated with experimentally tuning the control system. The initial application for this research is the High Speed Civil Transport inlet control problem. A major aspect of this research is the development of a controls/CFD interface for non-CFD experts, to facilitate the interactive operation of CFD simulations and the extraction of reduced-order, time-accurate models from CFD results. A distributed computing approach for implementing the interface is being explored. Software being developed as part of the Integrated CFD and Experiments (ICE) project provides the basis for the operating environment, including run-time displays and information (data base) management. Message-passing software is used to communicate between the ICE system and the CFD simulation, which can reside on distributed, parallel computing systems. Initially, the one-dimensional Large-Perturbation Inlet (LAPIN) code is being used to simulate a High Speed Civil Transport type inlet. LAPIN can model real supersonic inlet features, including bleeds, bypasses, and variable geometry, such as translating or variable-ramp-angle centerbodies. Work is in progress to use parallel versions of the multidimensional NPARC code.

Source record↗

NASA NTRS2014

Preliminary Study on Acoustic Detection of Faults Experienced by a High-Bypass Turbofan Engine

The vehicle integrated propulsion research (VIPR) effort conducted by NASA and several partners provided an unparalleled opportunity to test a relatively low TRL concept regarding the use of far field acoustics to identify faults occurring in a high bypass turbofan engine. Though VIPR Phase II ground based aircraft installed engine testing wherein a multitude of research sensors and methods were evaluated, an array of acoustic microphones was used to determine the viability of such an array to detect failures occurring in a commercially representative high bypass turbofan engine. The failures introduced during VIPR testing included commanding the engine's low pressure compressor (LPC) exit and high pressure compressor (HPC) 14th stage bleed values abruptly to their failsafe positions during steady state

acoustics↗