SEARCH · Search NASA

Results for “blending”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Electrocatalytic alkene epoxidation at disrupted metal ensembles in blended electrolytes

The project aims to achieve a molecular understanding of oxygen-atom transfer from water to alkenes at electrocatalytic interfaces. Molecular oxygen is the most common oxygen-atom source for epoxidations, and our group is developing sustainable routes through which epoxidation of olefins is achieved using water as the oxygen source. This route can improve the safety of the reaction while also co-producing hydrogen, demonstrating the relevance of this reaction to the energy transition. If successful in our efforts, we may enable oxygen-atom transfer reactions at the anode of water electrolyzers in the place of conventional oxygen evolution, allowing for the synthesis of sustainable value-added co-products. In this vein, we explore several approaches to acquiring high selectivity toward epoxidation over competing reactions, such as oxygen evolution. One of our aims is to allow for rational control of epoxide selectivity by disrupting contiguous metal ensembles at the surface of catalytic metal oxide nanoparticles. Specifically, we aim to synthesize single-atom, few-atom, and many-atom clusters supported on metal oxides and study the mechanism of oxygen evolution and alkene epoxidation on these materials. Thus, this approach will determine the impact of disrupting metal ensembles on the selectivity for alkene epoxidation versus oxygen evolution in blended electrolytes. Another aim is to develop a molecular-level understanding of how a blended electrolyte (i.e., a mixture of aqueous and organic solvents) influences rates of alkene epoxidation versus oxygen evolution. In other words, we are interested in understanding the catalytic influence of the solvent, as our preliminary work shows that the selectivity and reactivity of epoxidation depend strongly on the solvent composition. This investigation includes blended electrolytes and electrolytes containing redox mediator species that improve selectivity toward the desired epoxidation reaction. Overall, our proposed work will help to provide a detailed molecular-level picture of how solvents interact with substrates at the electrode-electrolyte interface, including their involvement in proton transfer reactions and screening of electric fields.

14 SOLAR ENERGY↗

DOE OSTI2025

Blending as an In-Tank Waste Processing Strategy: Year 1 Progress Report

The Hanford Site stores approximately 56 million gallons of radioactive legacy defense waste in underground tanks. Direct feed of southeast quadrant tank waste to a high-level waste treatment facility is currently being explored to accelerate tank treatment activities. This study seeks to de-risk waste transfers by favorably altering the resuspension and critical velocities of wastes through strategic waste blending. Wastes rich in aluminum- and zirconium-bearing solids pose significant risks due to their high settled strength and density. A series of tests explores how solid phase particle size and suspending phase chemistry alter waste transport properties, quantified through the just-suspended mixing speed (NJS), for pure and blended aluminum- and zirconium-bearing waste solid simulants. The study utilizes a range of gibbsites (three sizes spanning 10 to 90 µm) and zirconia solids (three sizes spanning 10 to 100 µm). As expected, the NJS of pure solids largely follows predictions based on literature correlations; blends of gibbsite and zirconium-bearing solids of differing particle sizes exhibit NJS maxima attributed to dense packing of the mixed-size settled solids. The findings of this study will assist in developing strategies to optimize the transport of waste solids for the safe and efficient delivery of tank waste.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1979

Viscoelastic properties of entangled polymers - Ternary blends of monodisperse homopolymers

In a previous publication from this laboratory, the Rouse-Bueche-Zimm molecular theory of viscoelasticity has been extended by using a transient network model to apply to binary blends of monodisperse polymers with chain entanglements. The dynamics of the entanglements were modeled both by the enhanced frictional coefficients and by the additional elastic couplings. It was recognized that entanglements not only may form between chains of the same lengths (intracomponent entanglements) but also between those of different lengths (intercomponent entanglements). At a given intercomponent entanglement, the longer chain was assumed to have the frictional coefficient of the shorter chain. Similarly, for blends consisting of several monodisperse components with different molecular weights, such modifications are also required to predict their linear viscoelastic behavior. The frequency of these interactions is assumed to be proportional to the weight ratio of the respective component chains in the blend. Equations of motion are formulated for each component and solved numerically for the relaxation time spectra. Linear viscoelastic properties such as the dynamic mechanical moduli, stress relaxation moduli, and zero-shear viscosity can then be computed for these systems by linear summation of those of the components.

Soong, D.↗

NASA NTRS1982

An analytical procedure for computing smooth transitions between two specified cross sections with applications to blended wing body configuration

An analytical procedure is described for designing smooth transition surfaces for blended wing-body configurations. Starting from two specified cross section shapes, the procedure generates a gradual transition from one cross section shape to the other as an analytic blend of the two shapes. The method utilizes a conformal mapping, with subsequent translation and scaling, to transform the specified and shapes to curves that can be combined more smoothly. A sample calculation is applied to a blended wing-body missile type configuration with a top mounted inlet.

Barger, R. L.↗

NASA NTRS1982

Tests of blending and correlation of distillate fuel properties

The development of a fuel test matrix, results from tests of several blends of distillate aircraft fuels, and the use of correlations in formulation determination during a NASA-sponsored program to identify new aircraft fuels are described. The program was initiated in order to characterize fuel blends which are appropriate for different types of combustors in use and under development. The fuels were required to feature a specified range of properties. Attention is given to fuel volatility, hydrogen content, aromatic content, freezing point, kinematic viscosity, and naphthalene content. Paraffinic and naphtenic base stocks were employed, using alkyl benzene, naphthene benzenes, and naphthalenes to adjust the blend properties. Categories for the test fuels comprised source-controlled and composition controlled fuels. Test results and compositions of various fuels are provided.

Erwin, J.↗

NASA NTRS1988

Antimisting kerosene: Low temperature degradation and blending

The inline filtration characteristics of freshly blended and degraded antimisting fuels (AMK) at low temperature are examined. A needle valve degrader was modified to include partial recirculation of degraded fuel and heat addition in the bypass loop. A pressure drop across the needle valve of up to 4,000 psi was used. The pressure drop across a 325 mesh filter screen placed inline with the degrader and directly downstream of the needle valve was measured as a function of time for different values of pressure drop across the needle valve. A volume flux of 1 gpm/sq in was employed based on the frontal area of the screen. It was found that, at ambient temperatures, freshly blended AMK fuel could be degraded using a single pass degradation at 4,000 psi pressure drop across the needle valve to give acceptable filterability performance. At fuel temperatures below -20 C, degradation becomes increasingly difficult and a single pass technique results in unacceptable filtration performance. Recirculation of a fraction of the degraded fuel and heat addition in the bypass loop improved low temperature degradation performance. The problem is addressed of blending the AMK additive with Jet A at various base fuel temperatures.

Yavrouian, A.↗

NASA NTRS1990

Biaxial extrusion of polyimide LARC-TPI and LARC-TPI blends

Biaxial films of polyimide LARC-TPI and LARC-TPI/liquid crystal polymer Xydar were extruded directly from the melt for the first time via an innovative extrusion technique. Three types of films, neat LARC-TPI, LARC-TPI/10 wt pct and 30 wt pct blends were processed as a part of this NASA-funded program. Processability was greatly enhanced by incorporating Xydar. The coefficient of thermal expansion was reduced from 34 ppm/C for the neat LARC-TPI to 15 ppm/C for the 10 wt pct Xydar blend and ultimately down to 1 to 3 ppm/C for the 30 wt pct blend films in the direction of extrusion. The maximum improvement in stiffness was realized by incorporating 10 wt pct Xydar (2.8 GPa up to 4.9 GPa). Tensile strength, however, experienced a drop as a result of Xydar addition, probably caused by inefficient mixing of the two phases.

Haghighat, R. Ross↗

NASA NTRS1991

Chemistry and properties of blends of acetylene terminated materials

As part of a NASA program to develop new high temperature/high performance structural materials, the chemistry and properties of acetylene-containing materials and their cured resins are under investigation. The objective of this work is to develop materials that are readily processable (i.e., 200-300 C and about 1.4 MPa or less) and possess usable mechanical properties at temperatures as high as 177 C. An acetylene-terminated aspartimide (ATA) was blended with an equal weight of an acetylene-terminated arylene ether (ATAE) oligomer. The blend was subsequently thermally cured to yield a resin which was evaluated in the form of neat resin moldings, adhesive specimens, and laminates. Adhesive specimens and laminates gave good mechanical properties to temperatures as high as 177 C. In addition, preliminary laminate work is presented on the resin from a blend of a new N-methyl substituted ATA and an ATAE.

Connell, John W.↗

NASA NTRS1957

Preliminary investigation of the combustion of a 50 percent pentaborane - 50 percent JP-4 fuel blend in a turbojet combustor at simulated altitude conditions

A preliminary investigation was conducted to determine the combustion characteristics of a fuel composed of 50 percent pentaborane and 50 percent JP-4 (MIL-F-5624A) by weight in a turbojet combustor. A combustor designed to fit the housing of a J33-A-23 turbojet engine was selected for convenience. The fuel was evaluated at two engine conditions simulating altitudes of 40,000 and 57,000 feet, an engine speed of 85 percent of rated rpm, and a flight Mach number of 0.6. The pentaborane blend was initially evaluated in combustors developed for pure pentaborane and diborane reported in NACA RM E53B18 and RM E52L15. The performance of the blend was unsatisfactory in these combustors. A new combustor was then developed which provided combustor efficiencies measured from 91 to 101 percent as compared with efficiencies of 92 to 94 percent previously obtained for pentaborane at comparable conditions. Additional refinements of design details are needed to obtain lower oxide deposits and a more uniform outlet temperature profile; however, the combustor is believed to incorporate some of the design principles required to obtain satisfactory over-all performance with the fuel blend investigated.

FUELS - JP-4-*PENTABORANE↗

NASA NTRS1945

Flight and Test-stand Investigation of High-performance Fuels in Modified Double-row Radial Air-cooled Engines III: Knock-limited Performance of 33-R as Compared with a Triptane Blend and 28-R in Flight

A comparison has been made in flight of the antiknock characteristics of 33-R fuel with that of 28-R and a triptane blent. The knock-limited performance of the three fuels - 33-R, a blend of 80 percent 28-R plus 20 percent triptane (leaded to 4.5 ml TEL/gal), and 28-R - was investigated in two modified 14-cylinder double-row radial air-cooled engines. Tests were conducted on the engines as installed in the left inboard nacelle of an airplane. A carburetor-air temperature of approximately 85 deg F was maintained. The conditions covered at an engine speed of 2250 rpm were high and low blower ratios and spark advances of 25 deg and 32 deg B.T.C. For an engine speed of 1800 rpm only the high-blower condition was investigated for both 25 deg and 32 deg spark advances. For the conditions investigated the difference between 33-R and the triptane blend was found to be slight; the performance of 33-R fuel, however, was slightly higher than that of the triptane blend in the lean region. The knock-limited power obtained with the 33-R fuel was from 14 to 28 percent higher than that of the 28-R fuel for the entire range of test conditions; the greatest improvement was shown in the lean region.

Blackman, Calvin C.↗

NASA NTRS1993

Cyanoresin, cyanoresin/cellulose triacetate blends for thin film, dielectric capacitors

Non-brittle dielectric films are formed by blending a cyanoresin such as cyanoethyl, hydroxyethyl cellulose (CRE) with a compatible, more crystalline resin such as cellulose triacetate. The electrical breakdown strength of the blend is increased by orienting the films by uniaxial or biaxial stretching. Blends of high molecular weight CRE with high molecular weight cyanoethyl cellulose (CRC) provide films with high dielectric constants.

Yen, Shiao-Ping↗

NASA NTRS1960

Investigation at Mach Numbers of 0.20 to 3.50 of Blended Wing-Body Combinations of Sonic Design with Diamond, Delta, and Arrow Plan Forms

The models had aspect-ratio-2 diamond, delta, and arrow wings with the leading edges swept 45.00 deg, 59.04 deg, and 70.82 deg, respectively. The wing sections were computed by varying the section shape along with the body radii (blending process) to match the prescribed area distribution and wing plan form. The wing sections had an average value of maximum thickness ratio of about 4 percent of the local chords in a streamwise direction. The models were tested with transition fixed at Reynolds numbers of about 4,000,000 to 9,000,0000, based on the mean aerodynamic chord of the wings. The effect of varying Reynolds number was checked at both subsonic and supersonic speeds. The diamond model was superior to the other plan forms at transonic speeds ((L/D)max = 11.00 to 9.52) because of its higher lift-curve slope and near optimum wave drag due to the blending process. For the wing thickness tested with the diamond model, the marked body and wing contouring required for transonic conditions resulted in a large wave-drag penalty at the higher supersonic Mach numbers where the leading and trailing edges of the wing were supersonic. Because of the low sweep of the trailing edge of the delta model, this configuration was less adaptable to the blending process. Removing a body bump prescribed by the Mach number 1.00 design resulted in a good supersonic design. This delta model with 10 percent less volume was superior to the other plan forms at Mach numbers of 1.55 to 2.35 ((L/D)max = 8.65 to 7.24), but it and the arrow model were equally good at Mach numbers of 2.50 to 3.50 ((L/D)max - 6.85 to O.39). At transonic speeds the arrow model was inferior because of the reduced lift-curve slope associated with its increased sweep and also because of the wing base drag. The wing base-drag coefficients of the arrow model based on the wing planform area decreased from a peak value of 0.0029 at Mach number 1.55 to 0.0003 at Mach number 3.50. Linear supersonic theory was satisfactory for predicting the aerodynamic trends at Mach numbers from 1.55 to 3.50 of lift-curve slope, wave drag, drag due to lift, aerodynamic-center location, and maximum lift-drag ratios for each of the models.

Holdaway, George H.↗

NASA NTRS2003

A New Fitting Procedure for the Blended He I 1083 nm Multiplet

The He I 1083 nm multiplet is a powerful tool for observing the outer solar atmosphere but is difficult to analyze because the lines are weak, highly variable, and spectrally blended, both internally and with other neighboring solar and telluric lines. After separation from nearby spectral features, two components of the He I multiplet are resolved. Fitting these lines with two unconstrained Gaussian profiles always gives a ratio of major to minor component of less than half the value which would be expected for optically thin lines. One possibility for explaining the discrepancy between the weakness of the lines and the ratio of the spectral components is to assume that the line formation regions are concentrated in laterally unresolved, optically thick structures with small filling factor. However, we present here a least-squares fitting technique using cubic splines with fixed breakpoints with the constraint that the blend is the sum of three identically shaped profiles shifted in wavelength according to the atomic structure of the blend and weighted by the corresponding statistics weights, in agreement with optically thin line formation. The basis functions for the fitting procedure have no built-in spectral symmetry or shape. The resulting underlying profiles tend to be asymmetric with excess absorption to the blue, consistent with formation by "hot" and "cool" spatial elements within the observed volume, with the hotter regions having differential motion toward the observer. The results agree well with NASA/XSO Spectromagnetograph observations in quiet sun and coronal holes. Partial funding of this research was provided through the NASA Sun-Earth Connection SR&T program.

Jones, H. P.↗

NASA NTRS2002

Compatibility Studies of Hydrogen Peroxide and a New Hypergolic Fuel Blend

Several preliminary materials compatibility studies have been conducted to determine the practicality of a new hypergolic fuel system. Hypergolic fuel ignites spontaneously as the oxidizer decomposes and releases energy in the presence of the fuel. The bipropellant system tested consists of high-test hydrogen peroxide (HTP) and a liquid fuel blend consisting of a hydrocarbon fuel, an ignition enhancer and a transition metal catalyst. In order for further testing of the new fuel blend to take place, some basic materials compatibility and HTP decomposition studies must be accomplished. The thermal decomposition rate of HTP was tested using gas evolution and isothermal microcalorimetry (IMC). Materials were analyzed for compatibility with hydrogen peroxide including a study of the affect welding has on stainless steel elemental composition and its relation to HTP decomposition. Compatibility studies of valve materials in the fuel blend were performed to determine the corrosion resistance of the materials.

Baldridge, Jennifer↗

NASA NTRS1996

Cyanoresin, cyanoresin/cellulose triacetate blends for thin film, dielectric capacitors

Non brittle dielectric films are formed by blending a cyanoresin such as cyanoethyl, hydroxyethyl cellulose (CRE) with a compatible, more crystalline resin such as cellulose triacetate. The electrical breakdown strength of the blend is increased by orienting the films by uniaxial or biaxial stretching. Blends of high molecular weight CRE with high molecular weight cyanoethyl cellulose (CRC) provide films with high dielectric constants.

Yen, Shiao-Ping S.↗

NASA NTRS2013

Thermal Stability Results of a Fischer-Tropsch Fuel With Various Blends of Aromatic Solution

Fischer-Tropsch (F-T) jet fuel composition differs from petroleum-based, conventional commercial jet fuel because of differences in feedstock and production methodology. F-T fuel typically has a lower aromatic and sulfur content and consists primarily of iso and normal paraffins. The ASTM D3241 specification for Jet Fuel Thermal Oxidation Test (JFTOT) break point testing method was used to test the breakpoint of a baseline commercial grade F-T jet fuel, and various blends of this F-T fuel with an aromatic solution. The goal of this research is to determine the effect of aromatic content on the thermal stability of F-T fuel. The testing completed in this report was supported by the NASA Fundamental Aeronautics Subsonic Fixed Wing Project. Two different aromatic content fuels from Rentech, as well as these fuels with added aromatic blend were analyzed for thermal stability using the JFTOT method. Preliminary results indicate a reduction in thermal stability occurs upon increasing the aromatic content to 10% by adding an aromatic blend to the neat fuel. These results do not specify a failure based on pressure drop, but only on tube color. It is unclear whether tube color correlates to more deposition on the tube surface or not. Further research is necessary in order to determine if these failures are true failures based on tube color. Research using ellipsometry to determine tube deposit thickness rather than color will be continued in follow-up of this study.

Lindsey, Jennifer↗

NASA NTRS2016

Engineering Polymer Blends for Impact Damage Mitigation

Structures containing polymers such as DuPont's Surlyn® 8940, demonstrate puncture healing when impacted by a 9 millimeter projectile traveling from speeds near 300 meters per second (1,100 feet per second) to hypervelocity impacts in the micrometeoroid velocity range of 5 kilometers per second (16,000 feet per second). Surlyn® 8940 puncture heals over a temperature range of minus 30 degrees Centigrade to plus 70 degrees Centigrade and shows potential for use in pressurized vessels subject to impact damage. However, such polymers are difficult to process and limited in applicability due to their low thermal stability, poor chemical resistance and overall poor mechanical properties. In this work, several puncture healing engineered melt formulations were developed. Moldings of melt blend formulations were impacted with a 5.56 millimeter projectile with a nominal velocity of 945 meters per second (3,100 feet per second) at about 25 degrees Centigrade, 50 degrees Centigrade and 100 degrees Centigrade, depending upon the specific blend being investigated. Self-healing tendencies were determined using surface vacuum pressure tests and tensile tests after penetration using tensile dog-bone specimens (ASTM D 638-10). For the characterization of tensile properties both pristine and impacted specimens were tested to obtain tensile modulus, yield stress and tensile strength, where possible. Experimental results demonstrate a range of new puncture healing blends which mitigate damage in the ballistic velocity regime.

Gordon, Keith L.↗

NASA NTRS2017

Methods of Constructing a Blended Performance Function Suitable for Formation Flight

This paper presents two methods for constructing an approximate performance function of a desired parameter using correlated parameters. The methods are useful when real-time measurements of a desired performance function are not available to applications such as extremum-seeking control systems. The first method approximates an a priori measured or estimated desired performance function by combining real-time measurements of readily available correlated parameters. The parameters are combined using a weighting vector determined from a minimum-squares optimization to form a blended performance function. The blended performance function better matches the desired performance function mini- mum than single-measurement performance functions. The second method expands upon the first by replacing the a priori data with near-real-time measurements of the desired performance function. The resulting blended performance function weighting vector is up- dated when measurements of the desired performance function are available. Both methods are applied to data collected during formation- flight-for-drag-reduction flight experiments.

control systems↗