SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Small cylindrical test chamber determines catalytic effect of given container material on fuel that might contribute to accidental deflagration or detonation below expected temperature under adiabatic compression. Device is useful to producers and users of flammable liquids and to safety specialists.
A new technique of producing hollow spheres of many materials at a very rapid rate, at very low cost, and with high reproducibility of shell diameter and wall thickness has been developed. Shells formed of metal or of other solid materials are expected to find numerous technical and industrial applications. For example, metal shells might be used as inertial confinement fusion targets, or as the principal constituents in lightweight structural materials for NASA Space Stations or DOD large antennas and mirrors, or be employed as containers for phase-change heat-storage media, or serve as containers for hazardous materials, or be employed as catalytic surface agents.
Accumulation of noncondensible gas (NCG) has been observed in ammonia heat pipes. NCG has been found to be detrimental to the performance of heat pipes and can result in complete operational failure. A kinetic and thermodynamic analysis has been performed that evaluates the dissociation of ammonia under various conditions and predicts the amount of NCG present in heat pipes. The analysis indicates that the observed NCG in ammonia heat pipes can be attributed to the dissociation of ammonia into its constituents, hydrogen and nitrogen. It shows time and temperature to be the important parameters, in conjunction with the catalytic characteristic of the container material.
This investigation is a continuation of a previous study on nonequilibrium convective heat transfer to a blunt body. In the previous study, for relatively high Reynolds number flows, it was found that: nonequilibrium convective heat transfer to a blunt body is not strongly dependent on freestream parameters, provided that the thermochemical equilibrium is reached at the edge of boundary layer; and successful testing of convective heat transfer in an arc-jet environment is possible by duplicating the surface pressure and total enthalpy. The nonequilibrium convective heat transfer computations are validated against the results of Fay and Riddell/Goulard theory. Present work investigates low Reynolds number conditions which are typical in an actual arc-jet flow environment. One expects that there will be departures from the Fay and Riddell/Goulard result since certain assumptions of the classical theory are not satisfied. These departures are of interest because the Fay and Riddell/Goulard formulas are extensively used in arc-jet testing (e.g., to determine the enthalpy of the flow and the catalytic efficiency of heat shield materials). For practical sizes of test materials, density of the test flow (and Reynolds number) in an arc-jet is such that thermochemical equilibrium may not be reached at the edge of boundary layer. For blunt body flows of nitrogen and air, computations will be presented to show the effects of thermochemical nonequilibrium at the boundary layer edge on nonequilibrium heat transfer.
On-board propulsion functions include orbit insertion, orbit maintenance, constellation maintenance, precision positioning, in-space maneuvering, de-orbiting, vehicle reaction control, planetary retro, and planetary descent/ascent. This paper discusses on-board chemical propulsion technology, including bipropellants, monopropellants, and micropropulsion. Bipropellant propulsion has focused on maximizing the performance of Earth storable propellants by using high-temperature, oxidation-resistant chamber materials. The performance of bipropellant systems can be increased further, by operating at elevated chamber pressures and/or using higher energy oxidizers. Both options present system level difficulties for spacecraft, however. Monopropellant research has focused on mixtures composed of an aqueous solution of hydroxl ammonium nitrate (HAN) and a fuel component. HAN-based monopropellants, unlike hydrazine, do not present a vapor hazard and do not require extraordinary procedures for storage, handling, and disposal. HAN-based monopropellants generically have higher densities and lower freezing points than the state-of-art hydrazine and can higher performance, depending on the formulation. High-performance HAN-based monopropellants, however, have aggressive, high-temperature combustion environments and require advances in catalyst materials or suitable non-catalytic ignition options. The objective of the micropropulsion technology area is to develop low-cost, high-utility propulsion systems for the range of miniature spacecraft and precision propulsion applications.
An important consideration in the design of spacecraft for interplanetary missions is the compatibility of storage materials with the propellants. Serious problems can arise because many propellants are either extremely reactive or subject to catalytic decomposition, making the selection of proper materials of construction for propellant containment and control a critical requirement for the long-life applications. To aid in selecting materials and designing and evaluating various propulsion subsystems, available information on the compatibility of spacecraft materials with propellants of interest was compiled from literature searches and personal contacts. The compatibility of both metals and nonmetals with hydrazine, monomethyl hydrazine, nitrated hydrazine, and diborance fuels and nitrogen tetroxide, fluorine, oxygen difluoride, and Flox oxidizers was surveyed. These fuels and oxidizers encompass the wide variety of problems encountered in propellant storage. As such, they present worst case situations of the propellant affecting the material and the material affecting the propellant. This includes material attack, propellant decomposition, and the formation of clogging materials.
This paper describes the design and results of a surface catalysis flight experiment flown on the Orion Multipurpose Crew Vehicle during Exploration Flight Test 1 (EFT1). Similar to previous Space Shuttle catalytic tile experiments, the present test consisted of a highly catalytic coating applied to an instrumented TPS tile. However, the present catalytic tile experiment contained significantly more instrumentation in order to better resolve the heating overshoot caused by the change in surface catalytic efficiency at the interface between two distinct materials. In addition to collecting data with unprecedented spatial resolution of the "overshoot" phenomenon, the experiment was also designed to prove if such a catalytic overshoot would be seen in turbulent flow in high enthalpy regimes. A detailed discussion of the results obtained during EFT1 is presented, as well as the challenges associated with data interpretation of this experiment. Results of material testing carried out in support of this flight experiment are also shown. Finally, an inverse heat conduction technique is employed to reconstruct the flight environments at locations upstream and along the catalytic coating. The data and analysis presented in this work will greatly contribute to our understanding of the catalytic "overshoot" phenomenon, and have a significant impact on the design of future spacecraft.
Possible interpretations of the results of the Viking Biology Experiments suggest that greater than 1 ppm of a thermally labile oxidant, perhaps H2O2, and about 10 ppm of a thermally stable oxidant are present in the martian soil. We reexamine these results and discuss implications for future missions, the search for organics on Mars, and the possible health and engineering effects for human exploration. We conclude that further characterization of the reactivity of the martian regolith materials is warrented-although if our present understanding is correct the oxidant does not pose a hazard to humans. There are difficulties in explaining the reactivity of the Martian soil by oxidants. Most bulk phase compounds that are capable of oxidizing H2O to O2 per the Gas Exchange Experiment (GEx) are thermally labile or unstable against reduction by atmospheric CO2. Models invoking trapped O2 or peroxynitrates (NOO2(-)) require an unlikely geologic history for the Viking Lander 2 site. Most suggested oxidants, including H2O2, are expected to decompose rapidly under martian UV. Nonetheless, we conclude that the best model for the martian soil contains oxidants produced by heterogeneous chemical reactions with a photochemically produced atmospheric oxidant. The GEx results may be due to catalytic decomposition of an unstable oxidizing material by H2O. We show that interfacial reaction sites covering less than 1% of the available soil surfaces could explain the Viking Biology Experiments results.
Cyclic convective heating test results show that all surface insulation materials tested exhibit a wide range of surface emittance and catalytic activity depending on their surface coatings. Coatings have a significant effect on the overall material response depending on boundary layer characteristics.
The generally accepted theory for the origin of life on the Earth requires that a large variety of organic compounds be present to form the first living organisms and to provide the energy sources for primitive life either directly or through various fermentation reactions. This can provide a strong constraint on discussions of the formation of the Earth and on the composition of the primitive atmosphere. In order for substantial amounts of organic compounds to have been present on the prebiological Earth, certain conditions must have existed. There is a large body of literature on the prebiotic synthesis of organic compounds in various postulated atmospheres. In this mixture of abiotically synthesized organic compounds, the amino acids are of special interest since they are utilized by modern organisms to synthesize structural materials and a large array of catalytic peptides.
One possible origin of prebiotic organic material is that these compounds were formed via Fischer-Tropsch-type (FTT) reactions of carbon monoxide and hydrogen on silicate and oxide grains in the warm, inner-solar nebula. To investigate this possibility, an experimental system has been built in which the catalytic efficiency of different grain-analog materials can be tested. During such runs, the gas phase above these grain analogs is sampled using Fourier transform infrared (FT-IR) spectroscopy. To provide quantitative estimates of the concentration of these gases, a technique in which high-resolution spectra of the gases are calculated using the high-resolution transmission molecular absorption (HITRAN) database is used. Next, these spectra are processed via a method that mimics the processes giving rise to the instrumental line shape of the FT-IR spectrometer, including apodization, self-apodization, and broadening due to the finite resolution. The result is a very close match between the measured and computed spectra. This technique was tested using four major gases found in the FTT reactions: carbon monoxide, methane, carbon dioxide, and water. For the ranges typical of the FTT reactions, the carbon monoxide results were found to be accurate to within 5% and the remaining gases accurate to within 10%. These spectra can then be used to generate synthetic calibration data, allowing the rapid computation of the gas concentrations in the FTT experiments.
Advanced laser-based diagnostics have been developed to examine catalytic effects and atom/surface interactions on thermal protection materials. This study establishes the feasibility of using laser-induced fluorescence for detection of O and N atom loss in a diffusion tube to measure surface catalytic activity. The experimental apparatus is versatile in that it allows fluorescence detection to be used for measuring species selective recombination coefficients as well as diffusion tube and microwave discharge diagnostics. Many of the potential sources of error in measuring atom recombination coefficients by this method have been identified and taken into account. These include scattered light, detector saturation, sample surface cleanliness, reactor design, gas pressure and composition, and selectivity of the laser probe. Recombination coefficients and their associated errors are reported for N and O atoms on a quartz surface at room temperature.
Modules containing beds of enzymatic material catalyzing oxidation of primary alcohols and some other organic compounds developed for use in wastewater-treatment systems of future spacecraft. Designed to be placed downstream of multifiltration modules, which contain filters and sorbent beds removing most of non-alcoholic contaminants but fail to remove significant amounts of low-molecular-weight, polar, nonionic compounds like alcohols. Catalytic modules also used on Earth to oxidize primary alcohols and other compounds in wastewater streams and industrial process streams.
A review is given of the nonequilibrium calculation techniques by various authors over the past decade to predict heat fluxes to the windward side of the Space Shuttle orbiter. The results of these techniques are compared with measurements made on the first few flights of the Space Shuttle. The calculations attempt to account for finite rate chemistry in the shock layer around the vehicle and for finite rate catalytic atom recombination on the thermal protection materials. The techniques considered are the axisymmetric viscous shock layer method, three dimensional reacting Euler equation solutions coupled with axisymmetric analog boundary layer method, and a recently developed nonequilibrium 3-D viscous shock layer method.
A wet oxidation process was developed for oxidizing waste materials, comprising dissolved ruthenium salt in a reactant feed stream containing the waste materials. The feed stream is introduced into a reactor, and the reactor contents are then raised to an elevated temperature to effect deposition of a catalytic surface of ruthenium black on the interior walls of the reactor. The feed stream is then maintained in the reactor for a period of time sufficient to effect at least partial oxidation of the waste materials.
Earlier Shuttle flight experiments have shown atomic oxygen within the orbital environment can interact with many materials to produce surface recession and mass loss and combine catalytically with other constituents to generate visible and infrared glows. In addition to these effects, examinations of returned satellite hardware have shown many spacecraft materials are also susceptible to damage from high velocity impacts with orbital space debris. These effects are of particular concern for large, multi-mission spacecraft, such as Space Station and SDI operational satellites, that will operate in low-Earth orbit (LEO) during the late 1990's. Not only must these spacecraft include materials and exterior coatings that are resistant to atomic oxygen surface interactions, but these materials must also provide adequate protection against erosion and pitting that could result from numerous impacts with small particles (less than 100 microns) of orbital space debris. An overview of these concerns is presented, and activities now underway to develop materials and coatings are outlined that will provide adequate atomic protection for future spacecraft. The report also discusses atomic oxygen and orbital debris flight experiments now under development to expand our limited data base, correlate ground-based measurments with flight results, and develop an orbital debris collision warning system for use by future spacecraft.
This report presents the results of a one-year project, funded by NASA’s Kennedy Space Center Innovation Fund in FY18, to conduct a theoretical study on the effect of the Mars environment on spacecraft materials. Corrosion resistance is one of the most important properties in selecting materials for landed spacecraft and structures that will support surface operations for the human exploration of Mars. Currently, the selection of materials is done by assuming that the corrosion behavior of a material on Mars will be the same as that on Earth. This is understandable since there is no data on the corrosion resistance of materials in the Mars environment. However, given that corrosion is defined as the degradation of a metal that results from its chemical interaction with the environment, it cannot be assumed that corrosion is going to be the same in both environments since they are significantly different. The goal of this research was to develop a systematic approach to understand corrosion of spacecraft materials on Mars by conducting a literature search of available data, relevant to corrosion in the Mars environment. This project was motivated by the suggestion, by a team of researchers, that some of the structural degradation observed on Curiosity's wheels may have been caused by corrosive interactions with the transient liquid brines, reported to be present on Mars, while the most significant damage was attributed to rock scratching. An extensive literature search, on data relevant to corrosion on Mars, confirmed the need to investigate the interaction between materials, used for spacecraft and structures designed to support long-term surface operations on Mars, and the Mars environment. Previous preliminary experiments, designed to look at the interaction between aerospace aluminum alloy (AA7075-T73) and the gases present in the Mars atmosphere, at 20 degC and a pressure of 700 Pa, showed that there is an interaction between the small amount of oxygen present in the Mars gas and the alloy, when there is a scratch that removes the protective aluminum oxide film. Further studies are needed to consider many other important components of the Mars environment that can affect this interaction such as: the presence of brines, the interaction between these brines and materials, the effect of radiation on these interactions, and the possible catalytic effects of the clays present in the Martian regolith. This theoretical study provides strong justification to conduct experimental work to investigate the interaction between spacecraft materials with simulated Martian environments to reduce Mars exploration costs.
This paper presents the results of a literature search of available data relevant to corrosion resistance of materials in the Mars environment, as a background for future experimental work. Corrosion resistance is one of the most important properties in selecting materials for landed spacecraft and structures that will support surface operations for the human exploration of Mars. Currently, the selection of materials is done by assuming that the corrosion behavior of a material on Mars will be the same as that on Earth. This is understandable since there is no data available on the corrosion resistance of materials in the Mars environment. However, given that corrosion is defined as the degradation of a metal that results from its chemical interaction with the environment, it cannot be assumed that corrosion is going to be the same in both environments, since they are significantly different. This theoretical study was motivated by the suggestion, by a team of researchers, that some of the structural degradation observed on Curiosity's wheels may have been caused by corrosive interactions with the transient liquid brines, reported to be present on Mars, while the most significant damage was attributed to mechanical damage. An extensive literature search, on data relevant to corrosion on Mars, confirmed the need to investigate the interaction between materials, used for spacecraft and structures designed to support long-term surface operations on Mars, and the Mars environment. Experimental studies are needed to investigate the corrosion behavior of materials in relevant components of the Mars environment such as: the Mars atmosphere, the presence of brines, the interaction between these brines and materials, the effect of radiation on these interactions, and the possible catalytic effects of the clays present in the Martian regolith. The findings from this theoretical study provide strong justification to conduct experimental work to investigate the interaction between spacecraft materials with simulated Martian environments to reduce Mars exploration costs.