SEARCH · Search NASA

Results for “ceramic fillers”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS2009

Arcjet Tests of Different Gap-Filler Options for the Orion PICA Heatshield

PICA (Phenolic Infiltrated Carbon Ablator) is one of the candidate thermal protection materials for the Orion vehicle. Because PICA is fabricated in blocks, gaps exist between the blocks, similar to the individual ceramic tiles of the Shuttle thermal protection system. The results of this work focus on arcjet test results of different gap-filler options for PICA, performed as part of the Orion TPS Advanced Development Project. The arcjet tests were performed at NASA Ames Research Center on stagnation models 4 inches in diameter at conditions representative of Orion flight conditions for both Lunar and Low Earth Orbit return. Performance of gap-filler options was evaluated based on the extent of backface temperature change, as compared to PICA without gaps, and on the extent of flow penetration into the gap, evident from the gap opening and widening.

Skokova, Kristina↗

NASA NTRS1993

Thermal response and ablation characteristics of light weight ceramic ablators

An account is given of the thermal performance and ablation characteristics of the NASA-Ames Lightweight Ceramic Ablators (LCAs) in supersonic, high-enthalpy convective environments, which use low density ceramic or carbon fiber matrices as substrates for main structural support, with organic resin fillers. LCA densities are in the 0.224-1.282 g/cu cm range. In-depth temperature data have been obtained to determine thermal penetration depths and conductivity. The addition of SiC and PPMA is noted to significantly improve the ablation performance of LCAs with silica substrates. Carbon-based LCAs are the most mass-efficient at high flux levels.

Tran, Huy K.↗

NASA NTRS1992

Approaches to polymer-derived CMC matrices

The use of polymeric precursors to ceramics permits the fabrication of large, complex-shaped ceramic matrix composites (CMC's) at temperatures which do not degrade the fiber. Processing equipment and techniques readily available in the resin matrix composite industry can be adapted for CMC fabrication using this approach. Criteria which influence the choice of candidate precursor polymers, the use of fillers, and the role of fiber architecture and ply layup are discussed. Three polymer systems, polycarbosilanes, polysilazanes, and polysilsesquioxanes, are compared as candidate ceramic matrix precursors.

Hurwitz, Frances I.↗

NASA NTRS1992

Approaches to polymer-derived CMC matrices

Hurwitz, Frances I.↗

NASA NTRS1993

Production of Ultrafine, High-purity Ceramic Powders Using the US Bureau of Mines Developed Turbomill

Turbomilling, an innovative grinding technology developed by the U.S. Bureau of Mines in the early 1960's for delaminating filler-grade kaolinitic clays, has been expanded into the areas of particle size reduction, material mixing, and process reaction kinetics. The turbomill, originally called an attrition grinder, has been used for particle size reduction of many minerals, including natural and synthetic mica, pyrophyllite, talc, and marble. In recent years, an all-polymer version of the turbomill has been used to produce ultrafine, high-purity, advanced ceramic powders such as SiC, Si3N4, TiB2, and ZrO2. In addition to particle size reduction, the turbomill has been used to produce intimate mixtures of high surface area powders and whiskers. Raw materials, TiN, AlN, and Al2O3, used to produce a titanium nitride/aluminum oxynitride (TiN/AlON) composite, were mixed in the turbomill, resulting in strength increases over samples prepared by dry ball milling. Using the turbomill as a leach vessel, it was found that 90.4 pct of the copper was extracted from the chalcopyrite during a 4-hour leach test in ferric sulfate versus conventional processing which involves either roasting of the ore for Cu recovery or leaching of the ore for several days.

Hoyer, Jesse L.↗

DOE OSTI2022

A Review of Scalable Hexagonal Boron Nitride ( h -BN) Synthesis for Present and Future Applications

Hexagonal boron nitride (h-BN) is a layered inorganic synthetic crystal exhibiting high temperature stability and high thermal conductivity. As a ceramic material it has been widely used for thermal management, heat shielding, lubrication, and as a filler material for structural composites. Recent scientific advances in isolating atomically thin monolayers from layered van der Waals crystals to study their unique properties has propelled research interest in mono/few layered h-BN as a wide bandgap insulating support for nanoscale electronics, tunnel barriers, communications, neutron detectors, optics, sensing, novel separations, quantum emission from defects, among others. Realizing these futuristic applications hinges on scalable cost-effective high-quality h-BN synthesis. Here, in this work, the authors review scalable approaches of high-quality mono/multilayer h-BN synthesis, discuss the challenges and opportunities for each method, and contextualize their relevance to emerging applications. Maintaining a stoichiometric balance B:N = 1 as the atoms incorporate into the growing layered crystal and maintaining stacking order between layers during multi-layer synthesis emerge as some of the main challenges for h-BN synthesis and the development of processes to address these aspects can inform and guide the synthesis of other layered materials with more than one constituent element. Finally, the authors contextualize h-BN synthesis efforts along with quality requirements for emerging applications via a technological roadmap.

2D materials↗

NASA NTRS2004

Mechanically Strong Aerogels Formed by Templated Growth of Polymer Cross- Linkers on Inorganic Nanoparticles

In the search for materials with better mechanical, thermal, and electrical properties, it is becoming evident that oftentimes dispersing ceramic nanoparticles in plastics improves performance. Along these lines, chemical bonding (both covalent and noncovalent) between a filler and a polymer improves their compatibility, and thus enhances certain properties of the polymeric matrix above and beyond what is accomplished by simple doping with the filler. When a similarly sized dopant and matrix are used, elementary building blocks may also have certain distinct advantages (e.g., in catalysis). In this context, researchers at the NASA Glenn Research Center reasoned that in the extreme case, where the dopant and the matrix (e.g., a filler and a polymer) are not only sized similarly, but their relative amounts are comparable, the relative roles of the dopant and matrix can be reversed. Then, if the "filler," or a certain form thereof, possesses desirable properties of its own, such properties could be magnified by cross-linking with a polymer. We at Glenn have identified silica as such a filler in its lowest-density form, namely the silica aerogel.

Leventis, Nicholas↗

NASA NTRS2023

Experimental Investigation of Block-TPS Fence/Gap Roughness Effects on Transition Onset and Turbulent Heating at Mach 6

An experimental investigation of boundary-layer transition and convective surface heating on wind tunnel models that simulated aeroshells comprised of multiple blocks of thermal protection system (TPS) material has been performed. Two representative entry vehicle geometries, a sphere-cone aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic models of each geometry were fabricated with varying fence heights or gap depths to represent gap fillers that either protrude above, or are recessed below, the TPS blocks due to differential ablation during reentry. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Convective surface heating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations.

Aerothermodynamics↗

NASA NTRS1981

Abradable dual-density ceramic turbine seal system

A plasma sprayed dual density ceramic abradable seal system for direct application to the HPT seal shroud of small gas turbine engines. The system concept is based on the thermal barrier coating and depends upon an additional layer of modified density ceramic material adjacent to the gas flow path to provide the desired abradability. This is achieved by codeposition of inert fillers with yttria stabilized zirconia (YSZ) to interrupt the continuity of the zirconia struture. The investigation of a variety of candidate fillers, with hardness values as low as 2 on Moh's scale, led to the conclusion that solid filler materials in combination with a YSZ matrix, regardless of their hardness values, have a propensity for compacting rather than shearing as originally expected. The observed compaction is accompanied by high energy dissipation in the rub interaction, usually resulting in the adhesive transfer of blade material to the stationary seal member. Two YSZ based coating systems which incorported hollow alumino silicate spheres as density reducing agents were surveyed over the entire range of compositions from 100 percent filler to 100 percent YSZ. Abradability and erosion characteristics were determined, hardness and permeability characterized, and engine experience acquired with several system configurations.

Clingman, D. L.↗

DOE OSTI2020

Polymer-derived SiC/C/Al environmental barrier coatings on carbon steel

Carbon steel is a widely used structural material; however, it lacks corrosion resistance in water environments. An alternative approach to overcome this challenge is to implement the deposition of inherently corrosion-resistant ceramic coatings. SiC/C/Al coatings were developed at 700°C, using polycarbosilane in combination with Al and C, which were included as active and passive fillers, respectively. Here, we show that it is necessary to use Al particle sizes below 10 µm for them to function as an active filler below 900°C. Owing to their laminar microstructure, these coatings showed a cohesive delamination with an adhesion strength of 10 MPa. Results demonstrated that these coatings were able to reduce the corrosion of carbon steel in saline water by 99.7%, with corrosion rates of 38.33 mpy for carbon steel, and 0.099 and 0.155 mpy for SiC/C and SiC/C/Al (10 µm) coatings, respectively.

36 MATERIALS SCIENCE↗

NASA NTRS2002

Sol-Gel Derived Hafnia Coatings

Sol-gel derived hafnia coatings are being developed to provide an oxidation protection layer on ultra-high temperature ceramics for potential use in turbine engines (ultra-efficient engine technology being developed by NASA). Coatings using hafnia sol hafnia filler particles will be discussed along with sol synthesis and characterization.

Feldman, Jay D.↗

NASA NTRS1972

Evaluation of zirconia, thoria and zirconium diboride for advanced resistojet use

A literature survey was conducted to collect material properties data on all advanced high temperature materials. Three of these, Y2O3-stabilized ZrO2, ThO2, and ZrB2 with additives of C and SiC were selected for further study. Stabilized ZrO2 and ThO2 were found to have higher temperature oxidation resistance than any metal and great potential for use in advanced biowaste resistojets. ZrO2 has a lower electrical resistivity and sublimation and a higher creep endurance strength. ZrO2 and ThO2 tubular heat exchangers, electrically heated indirectly, were evaluated in short tests to about 1900 K in flowing CO2. ZrO2 was subjected to N2, H2, H2O and vacuum as well. X-ray diffraction and fluorescence analyses were made. The metal-to-ceramic seal technology for ZrO2 and ThO2 was developed using chemical vapor deposition of tantalum for metallizing and 82 Au - 18 Ni filler braze.

Page, R. J.↗

DOE OSTI2022

Radioactive waste immobilization of Hanford sludge in magnesium potassium phosphate ceramic forms

Here, this paper evaluates immobilization of Hanford K-Basin tank sludge in magnesium potassium phosphate ceramic forms. The waste forms were produced using two simulated non-radioactive sludge streams, each with distinct characteristics and composition. Ceramicrete with wollastonite as filler was used as the matrix for this purpose. The resulting waste forms were tested for their mechanical properties, radiation stability, and leaching resistance. In another series of tests, the samples were vitrified in borosilicate glass and glass waste forms were produced. The Product Consistency Test, the American Nuclear Society's ANS 16.1 test, and the Toxicity Characteristic Leaching Procedure, which are used to develop waste acceptance criteria in the United States for permanent storage of treated waste, were used for evaluation of the leaching resistance of all waste forms.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

NASA NTRS1989

Internal wire guide for GTAW welding

A welding torch for gas tungsten arc welding apparatus has a filler metal wire guide positioned within the torch, and within the shielding gas nozzle. The wire guide is adjacent to the tungsten electrode and has a ceramic liner through which the wire is fed. This reduces the size of the torch and eliminates the outside clearance problems that exit with external wire guides. Additionally, since the wire is always within the shielding gas, oxidizing of the wire is eliminated.

Morgan, Gene E.↗

NASA NTRS2002

Morphologies, Processing and Properties of Ceramic Foams from Pre-Ceramic Foams from Pre-Ceramic Polymer Routes

The current research is focused on processing ceramic foams that have potential as a thermal protection material. Ceramic foams with different architectures were formed from the pyrolysis of pre-ceramic polymers at 1200 C in different atmospheres. In some systems a sacrificial polyurethane was used as the blowing agent. We have also processed foams using sacrificial fillers to introduce controlled cell sizes. Each sacrificial filler or blowing agent leads to a unique morphology. The effect of different fillers on foam morphologies will be presented. The presentation will also focus on characterization of these foams in terms of mechanical and thermal properties. Foams processed using these approaches having bulk densities ranging from 0.15 to 0.9 g per cubic centimeter and a cell sizes from 5 to 500 micrometers. Compression strengths ranged from 2 to 7 MPa for these materials.

Stackpoole, Mairead↗

DOE OSTI2023

Enhanced flexibility and thermal conductivity of HfC decorated carbon nanofiber mats

Future-generation spacecraft components allude discovery of novel materials that can withstand extreme environments (>2000 °C). The combined effect of ultra-high temperature ceramics (UHTCs) and carbon fibers (C f ) can satisfy the demanding requirements of aerospace applications. A novel, hybrid, and flexible hafnium carbide (HfC)-decorated carbon nanofiber (C nf ) mat was fabricated via electrospinning. Enhanced thermal stability of the flexible HfC decorated C nf over C nf can be elucidated from the 20-fold increment in thermal conductivity and the onset of degradation at higher temperatures (840 °C). Successful integration of multi-layered sandwich lattice using in-housed fabricated HfC decorated C nf showed retention of the fibrous structure even after extreme spark plasma sintering (SPS) process at 1850 °C. Fabricating a similar multi-layered structure using procured C f was unsuccessful due to bundled agglomeration and micron-sized fibers. High-load indentation suggests that HfC decorated C nf interlayer is stronger (~2.3 times) than the parent UHTC with no cracking at the interface. Compared with the HfC matrix, the indentation-damaged area at the interface reduced up to ~56% due to toughening mechanisms such as C nf , fiber pull-out and bridging. The synthesized HfC decorated Cnf mat is proposed as an ultra-thin filler material for joining similar or dissimilar UHTCs while maintaining similar chemistry and better mechanical integrity at the interface. Furthermore, the findings insinuate a new paradigm in designing hybrid and flexible ceramic-containing materials for thermal protection systems (TPS) of future-generation spacecraft components that can mitigate failure in extreme environments (>2000 °C).

36 MATERIALS SCIENCE↗

DOE OSTI2023

Size effects in 3D–printed polymer–derived, zirconium diboride–reinforced ceramic composites

Preceramic polymers are of interest for use in many manufacturing techniques such as injection molding, ceramic fiber infiltration, and additive manufacturing. However, off-gassing of low molecular weight oligomers occurs when these polymers cure, potentially leading to porosity in the cured part. Here to study how porosity and strength are affected by the size of the printed part, and the presence of a high surface area nano-scale filler, polycarbosilane (PCS) microrods of varying diameter were fabricated via direct ink writing (DIW), an additive manufacturing technique, with two ink formulations containing either zirconium diboride (ZrB 2 ) alone, or ZrB 2 and fumed alumina (FA). Sets of microrods were printed in a range of sizes by using print nozzles of 450, 634, 979, 1 346, or 1 702 μm in diameter, which were thermally cured, pyrolyzed to form ceramic composite microrods, and tested in 3-pt flexure. Porosity increased with increasing diameter, while failure strength decreased. For a given nozzle size, the microrods containing FA displayed lower porosity and higher strength (up to ~500 MPa) compared to the microrods containing only ZrB 2 . Weibull strength analysis was performed on each group of microrods and shows that the addition of FA increased Weibull modulus from 4.63 ± 1.56 to 9.35 ± 0.601. In conjunction with optical microscopy, this analysis indicates two distinct flaw populations in the printed materials, porosity which arises during the curing step and cracking which arises during pyrolysis of the larger specimens.

36 MATERIALS SCIENCE↗

NASA NTRS1990

Nicalon/siliconoxycarbide ceramic composites

A number of polymers of differing molecular structure, viscosity, copolymer composition, and production procedures, screened for production of strong, tough Nicalon/siliconoxycarbide composites, are discussed. Variables during polymer synthesis include pH, water/methoxy ratio and phenyl/methyl ratio. Final processing temperatures of the composites range from 1200 deg to 1400 deg C. The filler is derived from pyrolysis of the 50 phenyl/50 methyl silsesquioxane copolymer pyrolyzed to 650 deg C, then milled to less than 1-micron powder. Composite samples were fractured to evaluate the influence of matrix composition, final fabrication temperature, and use of filler on the composite mode of failure, modulus, strain capability, and strength. Incorporation of filler was found to increase matrix compressive strength and to influence matrix shrinkage and cracking.

Hurwitz, F. I.↗