Search NASA⌕ Search

SEARCH · Search NASA

Results for “charge generation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Green Additive Limits Runaway Crystallinity in PM6:Y6 Organic Solar Cells but Causes Field-Independent Geminate Recombination

Solvent additives are well-established for improving device performance of organic solar cells by enhancing nanodomain phase separation and crystallization. However, optimum additive concentrations are typically at trace amounts with slight fluctuations causing runaway crystallinity that short the device and limit scale-up potential. Furthermore, we show that a nonhalogenated solvent additive 1-phenylnaphthalene (PN) can be used to optimize high-performance PM6:Y6 devices, but without runaway crystallinity even at concentrations 10× above the optimum. Our holistic analysis of device losses shows that PN increases photoabsorption while decreasing bimolecular recombination. However, above the optimum, charge generation is reduced due to field-independent geminate recombination of charge transfer states that overcomes the other benefits. Rotated Y6 crystallite orientation is a likely culprit, where the device electric field is ineffective at separating the charges. Despite this, device performance remains higher than that of traditional additives, indicating a route to avoiding the high sensitivity of performance to processing conditions.

14 SOLAR ENERGY↗
DOE OSTI2025

Time Resolution Characterization of 4H-SiC LGADs with a 90 Sr Source

This work presents timing measurements of 4H-SiC Low Gain Avalanche Detectors (4H-SiC LGADs) using beta particles from a 90Sr source. The 4H-SiC LGADs exhibit fast signal responses, and a time resolution of 61 ps was achieved, comparable to that of standard Si LGADs. The present limitation in the time resolution of 4H-SiC LGADs appears to stem from limited charge generation. Nevertheless, their higher voltage tolerance and faster carrier drift suggest that, with increased charge collection, their timing performance could approach or even surpass that of Si LGADs. Furthermore, these results demonstrate the strong potential of 4H-SiC LGADs as a robust platform for precision timing in future 4D tracking detectors, while also highlighting that signal charge is the dominant factor currently limiting their performance, indicating that further optimization of gain and drift structures will be essential for future development.

43 PARTICLE ACCELERATORS↗
NASA NTRS1985

Mathematical physics approaches to lightning discharge problems

Mathematical physics arguments useful for lightning discharge and generation problems are pursued. A soliton Ansatz for the lightning stroke is treated including a charge generation term which is the ultimate source for the phenomena. Equations are established for a partially ionized plasma inding the effects of pressure, magnetic field, electric field, gravitation, viscosity, and temperature. From these equations is then derived the non-stationary generalized Ohm's Law essential for describing field/current density relationships in the horizon channel of the lightning stroke. The discharge initiation problem is discussed. It is argued that the ionization rate drives both the convective current and electric displacement current to increase exponentially. The statistical distributions of charge in the thundercloud preceding a lightning dischage are considered. The stability of the pre-lightning charge distributions and the use of Boltzmann relaxational equations to determine them are discussed along with a covered impedance path provided by the aircraft.

Kyrala, A.↗
DOE OSTI2023

Interactions between nonfullerene acceptors lead to unstable ternary organic photovoltaic cells

For organic photovoltaic (OPV) devices to achieve consistent performance and long operational lifetimes, organic semiconductors must be processed with precise control over their purity, composition, and structure. This is particularly important for high volume solar cell manufacturing where control of materials quality has a direct impact on yield and cost. Ternary-blend OPVs containing two acceptor–donor–acceptor (A–D–A)-type nonfullerene acceptors (NFAs) and a donor have proven to be an effective strategy to improve solar spectral coverage and reduce energy losses beyond that of binary-blend OPVs. Here, we show that the purity of such a ternary is compromised during blending to form a homogeneously mixed bulk heterojunction thin film. We find that the impurities originate from end-capping C=C/C=C exchange reactions of A–D–A-type NFAs, and that their presence influences both device reproducibility and long-term reliability. The end-capping exchange results in generation of up to four impurity constituents with strong dipolar character that interfere with the photoinduced charge transfer process, leading to reduced charge generation efficiency, morphological instabilities, and an increased vulnerability to photodegradation. As a consequence, the OPV efficiency falls to less than 65% of its initial value within 265 h when exposed to up to 10 suns intensity illumination. We propose potential molecular design strategies critical to enhancing the reproducibility as well as reliability of ternary OPVs by avoiding end-capping reactions.

14 SOLAR ENERGY↗
NASA NTRS1994

Monolithic in-based III-V compound semiconductor focal plane array cell with single stage CCD output

A monolithic semiconductor imager includes an indium-based III-V compound semiconductor monolithic active layer of a first conductivity type, an array of plural focal plane cells on the active layer, each of the focal plane cells including a photogate over a top surface of the active layer, a readout circuit dedicated to the focal plane cell including plural transistors formed monolithically with the monolithic active layer and a single-stage charge coupled device formed monolithically with the active layer between the photogate and the readout circuit for transferring photo-generated charge accumulated beneath the photogate during an integration period to the readout circuit. The photogate includes thin epitaxial semiconductor layer of a second conductivity type overlying the active layer and an aperture electrode overlying a peripheral portion of the thin epitaxial semiconductor layer, the aperture electrode being connectable to a photogate bias voltage.

Fossum, Eric R.↗
NASA NTRS1995

Monolithic in-based III-V compound semiconductor focal plane array cell with single stage CCD output

A monolithic semiconductor imager includes an indium-based III-V compound semiconductor monolithic active layer of a first conductivity type, an array of plural focal plane cells on the active layer, each of the focal plane cells including a photogate over a top surface of the active layer, a readout circuit dedicated to the focal plane cell including plural transistors formed monolithically with the monolithic active layer and a single-stage charge coupled device formed monolithically with the active layer between the photogate and the readout circuit for transferring photo-generated charge accumulated beneath the photogate during an integration period to the readout circuit. The photogate includes thin epitaxial semiconductor layer of a second conductivity type overlying the active layer and an aperture electrode overlying a peripheral portion of the thin epitaxial semiconductor layer, the aperture electrode being connectable to a photogate bias voltage.

Fossum, Eric R.↗
NASA NTRS1986

Plasma Source for Charge Control

Plasma source neutralizes electrical charge on spacecraft. When triggered by command from spacecraft potential monitor or from control system, plasma apparatus responds within about 1 s, generating charged plasma of required polarity. Discharging system to be tested on Air Force Geophysics Laboratory BERT-1 (Beam Emission Rocket Test) sounding rocket.

Aston, G.↗
DOE OSTI2021

New magnetic symmetries in (d + 2)-dimensional QED

Previous analyses of asymptotic symmetries in QED have shown that the subleading soft photon theorem implies a Ward identity corresponding to a charge generating divergent large gauge transformations on the asymptotic states at null infinity. In this work, we demonstrate that the subleading soft photon theorem is equivalent to a more general Ward identity. The charge corresponding to this Ward identity can be decomposed into an electric piece and a magnetic piece. The electric piece generates the Ward identity that was previously studied, but the magnetic piece is novel, and implies the existence of an additional asymptotic “magnetic” symmetry in QED.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Impedance sources (Z sources) with inherent fault protection for resilient and fire-free electricity grids

Modern societies would not survive without electricity and at the same time electrical faults could cause and have caused many catastrophes—mainly deadly fires—to our societies. There are two types of electricity sources: the voltage source such as generators, charged batteries and capacitors, and the current source such as charged inductors, current-regulated rectifiers, and superconducting magnetic energy storage. An “ideal” voltage source—that is often-sought-or-intentionally engineered—generates a constant voltage irrespective of its load current, and an “ideal” current source injects a constant current irrespective of its load voltage. However, two problems exist: (1) voltage or current sources do not represent many emerging natural/renewable energy sources such as wind turbine generators, photovoltaic cells, and fuel cells, whose output voltage and current are strongly dependent on each other, and (2) a short-circuit fault to an artificially-made and controlled “ideal” voltage source or an open-circuit fault to an “ideal” current source can cause catastrophic failures of the source itself and its surrounding circuits due to large (theoretically infinite) short-circuit current or open-circuit voltage. Here we introduce an impedance source concept to represent, characterize, and model those electricity sources whose output voltage and current are strongly dependent on each other. First, we found that many electric sources with no feedback (or active) control of their output voltage and/or current are a natural impedance source with inherent fault protection at short-circuit or open-circuit faults. Second, any electrical source can be artificially controlled to mimic a natural impedance source. Finally, we show how to apply natural impedance sources and nature-mimicking artificially-controlled sources to the electricity grid—the most complex machine ever made by human beings—to realize electricity grids that are naturally stable, self-protected against electrical faults, and resilient to natural and human-made events.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2025

A virtual Frisch-grid geometry-based CZT gamma detector for in-field radioisotope identification

Here, we present a Virtual Frisch-Grid geometry-based CZT gamma detector developed for identifying different radioisotopes over an energy range from a few keV up to 2 MeV, and useful for efficient characterization of CZT crystals. The detector is built with a 3 x 3 matrix of CZT crystals, each measuring approximately 6 mm x 6 mm x 15 mm. The charge generated within the sensor’s active volume is read out via an anode connected directly to the AVG3_Dev integrated circuit. A current signal induced by charge drift is collected on side pads of the crystals, enabling reconstruction of a 3D interaction position. This paper discusses the design, development, and performance of the standalone, mobile detector system, which integrates the AVG3_Dev readout IC developed at Brookhaven National Laboratory, a high-speed FPGA-based with per-channel digital signal processing, and embedded system capabilities. The device is compact, battery-powered, and supports wireless data streaming, making it suitable for field operations for radioisotope identification.

47 OTHER INSTRUMENTATION↗
NASA NTRS1979

Impulsive penetration and viscous interaction

How the magnetosheath plasma enters the entry layer and low latitude boundary layers, with the particle energy spectra almost unchanged is investigated. It was proposed by Lemaire that this is accomplished by impulsive penetration of plasma clouds of plasmoids. Once inside the magnetosphere, a plasmoid with its own momentum will polarize, to create its own electric field for continued motion. This voltage generator charges up the sides of the boundary layers, in the process creating the internal magnetospheric electric field. The entry layer particles will gradient and curvature drift, constituting still another generator, a current generator, to power magnetospheric plasma processes. This may be the explanation for the viscous interaction first proposed by Axford and Hines.

Heikkila, W. J.↗
DOE OSTI2023

Interface property–functionality interplay suppresses bimolecular recombination facilitating above 18% efficiency organic solar cells embracing simplistic fabrication

Efficient exciton-to-charge generation from the introduction of non-fullerene acceptors (NFAs) has been an important breakthrough in organic solar cell (OSC) developments. However, low device fill factors (FFs) following significant free charge carrier recombination loss continue to undermine their marketplace potential. Previous studies have successfully uncovered the importance of donor and acceptor domains in promoting charge transport. However, the functionality of donor/acceptor (D/A) interfaces relevant to free charge recombination remains unclear despite such interfaces being present throughout the material. In this work, the disorder-induced uphill bulk-to-D/A interface transport energy landscape is unveiled to enhance the polaron recombination resistance thereby also mitigating the triplet state formation from back charge transfer. In simple words, increasing the interface disorder while keeping the purer domains highly ordered will impart greater bulk-to-interface differential energy which then serves as a recombination energy barrier. Herein, these are made possible by varying the NFA outer side chains from linear alkyls to bulkier 2D phenylalkyls which influence the donor–acceptor interaction and define the interfacial disorder. Meanwhile, the extent of interface disorder without tradeoff in geminate losses is dependent on electrostatics and nanomorphology driving efficient exciton dissociation. By understanding these interplays, remarkable FFs over 80% and power conversion efficiencies (PCEs) above 18% are revealed to remain accessible even with simple binary component device fabrication without additional components/treatments thereby maintaining the scalability. Consequently, the principles uncovered here will serve as the foundation to reach the optimum potential of binary and simple systems, a prerequisite to ultimately realize the most cost-effective OSC design strategies for practical applications.

14 SOLAR ENERGY↗
NASA NTRS1983

Vehicle charging and potential on the STS-3 mission

An electron gun with fast pulse capability was used in the vehicle charging and potential experiment carried on the OSS-1 pallet to study dielectric charging, return current mechanisms, and the techniques required to manage the electrical charging of the orbiter. Return currents and charging of the dielectrics were measured during electron beam emission and plasma characteristics in the payload bay were determined in the absence of electron beam emission. The fast pulse electron generator, charge current probes, spherical retarding potential analyzer, and the digital control interface unit which comprise the experiment are described. Results show that the thrusters produce disturbances which are variable in character and magnitude. Strong ram/wake effects were seen in the ion densities in the bay. Vehicle potentials are variable with respect to the plasma and depend upon location on the vehicle relative to the main engine nozzles, the vehicle attitude, and the direction of the geomagnetic field.

Williamson, R.↗
DOE OSTI2024

A hybrid-kinetic simulation tool for non-thermal warm x-ray z-pinch sources, with gas-puff and wire array exemplars

Increasing the fluence of z-pinch x-ray radiation sources above ∼ 10 keV has been a long-standing goal for scientists at Sandia National Laboratories’ Z Machine. Optimizing sources for non-thermal “cold Kα” emission in higher atomic-number materials appears to be a promising path to increase warm x-ray yield. However, this emission is generated by supra-thermal electrons, which are not treated in the magnetohydrodynamic (MHD) codes that are typically used in z-pinch source development. MHD codes do not allow for charge separation or space-charge-generated electric fields, and constrain particle kinematics to Maxwellian distributions. The kinetic codes which do accommodate discrete, non-thermal energy distributions are computationally prohibitive when modeling plasmas near solid density and when modeling/tracking higher ionization states. Thus, modeling non-thermal z-pinch sources requires a new simulation tool. In this report, we present a new hybrid modeling capability that uses the fast features of MHD-type particles to the greatest extent possible, then transitions to the slower but more complete kinetic particle treatment to correctly capture the particle energy spectra that generate non-thermal emission. This capability is founded on the fully-relativistic particle-in-cell code Chicago, which already includes fluid particle treatments. The governing equations and hybrid methodology presented here are applied in simulations of an argon gas-puff and a molybdenum wire-array to provide preliminary code validation. The argon simulation is compared to measured implosion times and yields from Jones et al., Phys. Plasmas 22, 020706 (2015). The simulated x-ray yield is within 25% of measurements and the implosion times agree within a few percent. The molybdenum wire array simulation captures the implosion timing reported in Hansen et al., Phys. Plasmas 21, 031202 (2014), but work is needed to verify the available EOS table. These exemplar simulations represents the type of non-thermal sources that will be developed using the hybrid code capability going forward.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Exciton fission enhanced silicon solar cell

While silicon solar cells dominate global photovoltaic energy production, their continued improvement is hindered by the single-junction limit. One possible solution is to use molecular singlet exciton fission to generate two electrons from each absorbed high-energy photon. We demonstrate that the long-standing challenge of coupling molecular excited states to silicon solar cells can be overcome using sequential charge transfer. Combining zinc phthalocyanine, aluminum oxide, and a shallow junction crystalline silicon microwire solar cell, the peak charge generation efficiency per photon absorbed in tetracene is (138% ± 6%), comfortably surpassing the quantum efficiency limit for conventional silicon solar cells and establishing a new, scalable approach to low-cost, high-efficiency photovoltaics.

14 SOLAR ENERGY↗
DOE OSTI2024

Electric fields near undulating dielectric membranes

Dielectric interfaces are crucial to the behavior of charged membranes, from graphene to synthetic and biological lipid bilayers. Understanding electrolyte behavior near these interfaces remains a challenge, especially in the case of rough dielectric surfaces. A lack of analytical solutions consigns this problem to numerical treatments. Here, we report an analytic method for determining electrostatic potentials near curved dielectric membranes in a two-dimensional periodic “slab” geometry using a periodic summation of Green’s functions. This method is amenable to simulating arbitrary groups of charges near surfaces with two-dimensional deformations. We concentrate on one-dimensional undulations. We show that increasing membrane undulation increases the asymmetry of interfacial charge distributions due to preferential ionic repulsion from troughs. In the limit of thick membranes, we recover results mimicking those for electrolytes near a single interface. Our work demonstrates that rough surfaces generate charge patterns in electrolytes of charged molecules or mixed-valence ions.

Chemistry↗
NASA NTRS1995

Active pixel sensor with intra-pixel charge transfer

An imaging device formed as a monolithic complementary metal oxide semiconductor integrated circuit in an industry standard complementary metal oxide semiconductor process, the integrated circuit including a focal plane array of pixel cells, each one of the cells including a photogate overlying the substrate for accumulating photo-generated charge in an underlying portion of the substrate, a readout circuit including at least an output field effect transistor formed in the substrate, and a charge coupled device section formed on the substrate adjacent the photogate having a sensing node connected to the output transistor and at least one charge coupled device stage for transferring charge from the underlying portion of the substrate to the sensing node.

Fossum, Eric R.↗