Search NASASearch

SEARCH · Search NASA

Results for “chunking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Experimental Impacts into Chondritic Targets: Disruption of an L6 Chondrite by Multiple Impacts - Part 1

A fragment of an L6 chondrite (ALH 85017,13) with an initial mass (M(sub 0)) of 464.1 g was the target in a series of experimental impacts in which the largest remaining fragment (M(sub R)) after each shot was impacted by a 3.18-mm ceramic sphere at a nominal speed of 2 km/s. This continued until the mass of the largest remaining piece was less than half the mass of the target presented to that shot (M(sub S)). Two chunks of Bushveldt gabbro with similar initial masses were also impacted under the same conditions until M(sub R) was less than half M(sub 0). The two gabbro targets required a total of 1.51x10(exp 7) and 1.75x10(exp 7) erg/g to attain 0.27 and 0.33 M(sub R)/M(sub 0), respectively; the chondrite, however, was considerably tougher, reaching 0.40 and 0.21 M(sub R)/M(sub 0) only after receiving 2.37x10(exp 7) and 3.10x10(exp 7) erg g-1, respectively. The combined ejecta and spallation products from the gabbro impacts were coarser than those from the chondrite and in sufficient quantities that the new surface areas exceeded those from the meteorite until the fifth shot in the chondrite series, which was the number of impacts required to disrupt each gabbro target (i.e., MR/M0 = 0.5). Unlike the behavior shown in previous regolith-evolution series, neither gabbro target produced an enhancement in the size fraction reflecting the mean size of the crystals composing the rock (about 3 mm), an effect possibly related to the width of the shock pulse. The original chondrite was so fine-grained and fractured, and the variance in its grain-size distribution so large, that effects related to grain-size were relegated to the <63- m fraction. Impacts into ALH 85017 produced abundant, fine-grained debris, but otherwise the slopes of its size distributions were comparable to those from other experiments involving natural and fabricated terrestrial targets. The characteristic slopes of the chondrite's size distributions, however, were notably more constant over the entire nine-impact series than those from any of the terrestrial targets, a testament to the control over comminution apparently exerted by pre-existing fractures and other, microscopic damage in the meteorite. The enhancement in the finer fraction of debris from ALH 85017 indicates that ordinary chondrites in solar orbit would be very efficient contributors to the cosmic-dust complex. At the same time, the greater resistance to disruption displayed by ordinary chondrites relative to that exhibited by igneous rocks indicates that a selection effect could be operative between the annealed, ordinary-chondritic breccias and relatively weaker, differentiated meteorites. Preferential survival from their time in the regoliths of their parent bodies through their transit to Earth and passage through the atmosphere suggests that meteorite collections could be biased in favor of the ordinary chondrites.

Cintala, Mark J.

Tool for Sampling Permafrost on a Remote Planet

A report discusses the robotic arm tool for rapidly acquiring permafrost (RATRAP), which is being developed for acquiring samples of permafrost on Mars or another remote planet and immediately delivering the samples to adjacent instruments for analysis. The prototype RATRAP includes a rasp that protrudes through a hole in the bottom of a container that is placed in contact with the permafrost surface. Moving at high speed, the rasp cuts into the surface and loads many of the resulting small particles of permafrost through the hole into the container. The prototype RATRAP has been shown to be capable of acquiring many grams of permafrost simulants in times of the order of seconds. In contrast, a current permafrost sampling system that the RATRAP is intended to supplant works by scraping with tines followed by picking up the scrapings in a scoop, sometimes taking hours to acquire a few grams. Also, because the RATRAP inherently pulverizes the sampled material, it is an attractive alternative to other sampling apparatuses that generate core or chunk samples that must be further processed by a crushing apparatus to make the sample particles small enough for analysis by some instruments.

Peters, Gregory

The Planning Execution Monitoring Architecture

The Planning Execution Monitoring (PEM) architecture is a design concept for developing autonomous cockpit command and control software. The PEM architecture is designed to reduce the operations costs in the space transportation system through the use of automation while improving safety and operability of the system. Specifically, the PEM autonomous framework enables automatic performance of many vehicle operations that would typically be performed by a human. Also, this framework supports varying levels of autonomous control, ranging from fully automatic to fully manual control. The PEM autonomous framework interfaces with the core flight software to perform flight procedures. It can either assist human operators in performing procedures or autonomously execute routine cockpit procedures based on the operational context. Most importantly, the PEM autonomous framework promotes and simplifies the capture, verification, and validation of the flight operations knowledge. Through a hierarchical decomposition of the domain knowledge, the vehicle command and control capabilities are divided into manageable functional "chunks" that can be captured and verified separately. These functional units, each of which has the responsibility to manage part of the vehicle command and control, are modular, re-usable, and extensible. Also, the functional units are self-contained and have the ability to plan and execute the necessary steps for accomplishing a task based upon the current mission state and available resources. The PEM architecture has potential for application outside the realm of spaceflight, including management of complex industrial processes, nuclear control, and control of complex vehicles such as submarines or unmanned air vehicles.

Wang, Lui

The Carbon Crisis in 90 Seconds

This is a banana; and this is a chunk of coal. The banana is sweet and delicious and fun to eat... the coal is ... none of those things. But they are much more alike than they seem. Both were made by plants and store energy from the sun and carbon gas from the air around us. When you eat the banana, you use the energy stored in the banana to run and jump; and you release carbon gas back into the air around you. Now, carbon in the banana is young fast carbon: just weeks ago the banana was carbon gas in the air, and hours after you eat it, you breathe out the same carbon back into the air. When we burn coal in power plants, we use the energy stored in the coal to generate electricity that powers our homes and factories; and we release carbon gas back into the air around us. But, the carbon in the coal is old slow carbon. Plants took the coal carbon out of the air hundreds of millions of years ago. That carbon has been locked up ever since, and would stay locked up, if people hadn't dug up the coal and burned it. So now by burning coal and oil, people are adding lots and lots of old carbon to the atmosphere, faster than plants and the oceans can take it out. Why do I care? Because carbon gas in the atmosphere acts like a blanket, trapping heat, and making the whole planet warmer. My name is Peter, and I'm a carbon cycle scientist at NASA. We use satellites to watch how the world is warming. We can see the glaciers and the ice caps melting; and the air, land, and oceans warming. So we know we all have to change the way we produce and use energy, to burn less coal and oil, to prevent the planet from getting too warm.

Griffith, Peter

EOS MLS Level 2 Data Processing Software Version 3

This software accepts the EOS MLS calibrated measurements of microwave radiances products and operational meteorological data, and produces a set of estimates of atmospheric temperature and composition. This version has been designed to be as flexible as possible. The software is controlled by a Level 2 Configuration File that controls all aspects of the software: defining the contents of state and measurement vectors, defining the configurations of the various forward models available, reading appropriate a priori spectroscopic and calibration data, performing retrievals, post-processing results, computing diagnostics, and outputting results in appropriate files. In production mode, the software operates in a parallel form, with one instance of the program acting as a master, coordinating the work of multiple slave instances on a cluster of computers, each computing the results for individual chunks of data. In addition, to do conventional retrieval calculations and producing geophysical products, the Level 2 Configuration File can instruct the software to produce files of simulated radiances based on a state vector formed from a set of geophysical product files taken as input. Combining both the retrieval and simulation tasks in a single piece of software makes it far easier to ensure that identical forward model algorithms and parameters are used in both tasks. This also dramatically reduces the complexity of the code maintenance effort.

Livesey, Nathaniel J.

Terahertz Lasers Reveal Information for 3D Images

After taking off her shoes and jacket, she places them in a bin. She then takes her laptop out of its case and places it in a separate bin. As the items move through the x-ray machine, the woman waits for a sign from security personnel to pass through the metal detector. Today, she was lucky; she did not encounter any delays. The man behind her, however, was asked to step inside a large circular tube, raise his hands above his head, and have his whole body scanned. If you have ever witnessed a full-body scan at the airport, you may have witnessed terahertz imaging. Terahertz wavelengths are located between microwave and infrared on the electromagnetic spectrum. When exposed to these wavelengths, certain materials such as clothing, thin metal, sheet rock, and insulation become transparent. At airports, terahertz radiation can illuminate guns, knives, or explosives hidden underneath a passenger s clothing. At NASA s Kennedy Space Center, terahertz wavelengths have assisted in the inspection of materials like insulating foam on the external tanks of the now-retired space shuttle. "The foam we used on the external tank was a little denser than Styrofoam, but not much," says Robert Youngquist, a physicist at Kennedy. The problem, he explains, was that "we lost a space shuttle by having a chunk of foam fall off from the external fuel tank and hit the orbiter." To uncover any potential defects in the foam covering, such as voids or air pockets, that could keep the material from staying in place, NASA employed terahertz imaging to see through the foam. For many years, the technique ensured the integrity of the material on the external tanks.

Source record

Kennedy Space Center (KSC) Launch Pad Avian Abatement Efforts Including Related KSC Road Kill Reduction Effort

While birds might seem harmless, there's a good reason for the concern. During the July 2005 launch of Discovery on mission STS-1 14, a vulture soaring around the launch pad impacted the shuttle's external tank just after liftoff. With a vulture's average weight ranging from 3 to 5 pounds. a strike at a critical point on the Shuttle -- like the nose or wing leading thermal protection panels -- could cause catastrophic damage to the vehicle. The foam chunk that fatefully struck Columbia's wing in 2003 weighed only 1.7 pounds. (Cheryl L. Mansfield "Bye Bye Birdies" 2006) To address this issue, NASA formed an "Avian Abatement Team". The team goal is to have safer Shuttle missions by reducing the vulture population at KSC near the pad area thereby reducing the probability of another vulture strike during a Shuttle launch.

Schlierf, Roland

Collaborative WorkBench for Researchers - Work Smarter, Not Harder

It is important to define some commonly used terminology related to collaboration to facilitate clarity in later discussions. We define provisioning as infrastructure capabilities such as computation, storage, data, and tools provided by some agency or similarly trusted institution. Sharing is defined as the process of exchanging data, programs, and knowledge among individuals (often strangers) and groups. Collaboration is a specialized case of sharing. In collaboration, sharing with others (usually known colleagues) is done in pursuit of a common scientific goal or objective. Collaboration entails more dynamic and frequent interactions and can occur at different speeds. Synchronous collaboration occurs in real time such as editing a shared document on the fly, chatting, video conference, etc., and typically requires a peer-to-peer connection. Asynchronous collaboration is episodic in nature based on a push-pull model. Examples of asynchronous collaboration include email exchanges, blogging, repositories, etc. The purpose of a workbench is to provide a customizable framework for different applications. Since the workbench will be common to all the customized tools, it promotes building modular functionality that can be used and reused by multiple tools. The objective of our Collaborative Workbench (CWB) is thus to create such an open and extensible framework for the Earth Science community via a set of plug-ins. Our CWB is based on the Eclipse [2] Integrated Development Environment (IDE), which is designed as a small kernel containing a plug-in loader for hundreds of plug-ins. The kernel itself is an implementation of a known specification to provide an environment for the plug-ins to execute. This design enables modularity, where discrete chunks of functionality can be reused to build new applications. The minimal set of plug-ins necessary to create a client application is called the Eclipse Rich Client Platform (RCP) [3]; The Eclipse RCP also supports thousands of community-contributed plug-ins, making it a popular development platform for many diverse applications including the Science Activity Planner developed at JPL for the Mars rovers [4] and the scientific experiment tool Gumtree [5]. By leveraging the Eclipse RCP to provide an open, extensible framework, a CWB supports customizations via plug-ins to build rich user applications specific for Earth Science. More importantly, CWB plug-ins can be used by existing science tools built off Eclipse such as IDL or PyDev to provide seamless collaboration functionalities.

Ramachandran, Rahul

Characterize Human Forward Contamination Project

Let's face it: wherever we go, we will inevitably carry along the little critters that live in and on us. Conventional wisdom has long held that it's unlikely those critters could survive the space environment, but in 2007 microscopic animals called Tardigrades survived exposure to space and in 2008 Cyanobacteria lived for 548 days outside the International Space Station (ISS). But what about the organisms we might reasonably expect a crewed spacecraft to leak or vent? Do we even know what they are? How long might our tiny hitch-hikers survive in close proximity to a warm spacecraft that periodically leaks/vents water or oxygen-and how might they mutate with long-duration exposure? Unlike the Mars rovers that we cleaned once and sent on their way, crew members will provide a constantly regenerating contaminant source. Are we prepared to certify that we can meet forward contamination protocols as we search for life at new destinations? This project has four technical objectives: 1. TEST: Develop a test plan to leverage existing equipment (i.e. ISS) to characterize the kinds of organisms we can reasonably expect pressurized, crewed volumes to vent or leak overboard; 2. ANALYSIS: Develop an analysis plan to study those organisms in relevant destination environments, including spacecraft-induced conditions; 3. MODEL: Develop a modeling plan to model organism transport mechanisms in relevant destination environments; 4. SHARE: Develop a plan to disseminate findings and integrate recommendations into exploration requirements & ops. In short, we propose a system engineering approach to roadmap the necessary experiments, analysis, and modeling up front--rather than try to knit together disparate chunks of data into a sensible conclusion after the fact.

Rucker, Michelle

Characterize Human Forward Contamination Project

Let's face it: wherever we go, we will inevitably carry along the little critters that live in and on us. Conventional wisdom has long held that it's unlikely those critters could survive the space environment, but in 2007 microscopic animals called Tardigrades survived exposure to space and in 2008 Cyanobacteria lived for 548 days outside the International Space Station (ISS). But what about the organisms we might reasonably expect a crewed spacecraft to leak or vent? Do we even know what they are? How long might our tiny hitch-hikers survive in close proximity to a warm spacecraft that periodically leaks/vents water or oxygen-and how might they mutate with long-duration exposure? Unlike the Mars rovers that we cleaned once and sent on their way, crew members will provide a constantly regenerating contaminant source. Are we prepared to certify that we can meet forward contamination protocols as we search for life at new destinations? This project has four technical objectives: 1. TEST: Develop a test plan to leverage existing equipment (i.e. ISS) to characterize the kinds of organisms we can reasonably expect pressurized, crewed volumes to vent or leak overboard; as part of testing, we'll need to develop an Extravehicular Activity (EVA)-compatible tool that can withstand the pressure and temperature extremes of space, as well as collect, separate, and store multiple samples; 2. ANALYSIS: Develop an analysis plan to study those organisms in relevant destination environments, including spacecraft-induced conditions; 3. MODEL: Develop a modeling plan to model organism transport mechanisms in relevant destination environments; 4. SHARE: Develop a plan to disseminate findings and integrate recommendations into exploration requirements & ops. In short, we propose a system engineering approach to roadmap the necessary experiments, analysis, and modeling up front--rather than try to knit together disparate chunks of data into a sensible conclusion after the fact.

Rucker, Michelle

Concept Assessment of a Fission Fragment Rocket Engine (FFRE) Propelled Spacecraft

The March, 2012 issue of Aerospace America stated that ―the near-to-medium prospects for applying advanced propulsion to create a new era of space exploration are not very good. In the current world, we operate to the Moon by climbing aboard a Carnival Cruise Lines vessel (Saturn 5), sail from the harbor (liftoff) shedding whole decks of the ship (staging) along the way and, having reached the return leg of the journey, sink the ship (burnout) and return home in a lifeboat (Apollo capsule). Clearly this is an illogical way to travel, but forced on Explorers by today's propulsion technology. However, the article neglected to consider the one propulsion technology, using today's physical principles that offer continuous, substantial thrust at a theoretical specific impulse of 1,000,000 sec. This engine unequivocally can create a new era of space exploration that changes the way spacecraft operate. Today's space Explorers could travel in Cruise Liner fashion using the technology not considered by Aerospace America, the novel Dusty Plasma Fission Fragment Rocket Engine (FFRE). This NIAC study addresses the FFRE as well as its impact on Exploration Spacecraft design and operation. It uses common physics of the relativistic speed of fission fragments to produce thrust. It radiatively cools the fissioning dusty core and magnetically controls the fragments direction to practically implement previously patented, but unworkable designs. The spacecraft hosting this engine is no more complex nor more massive than the International Space Station (ISS) and would employ the successful ISS technology for assembly and check-out. The elements can be lifted in "chunks" by a Heavy Lift Launcher. This Exploration Spacecraft would require the resupply of small amounts of nuclear fuel for each journey and would be an in-space asset for decades just as any Cruise Liner on Earth. This study has synthesized versions of the FFRE, integrated one concept onto a host spacecraft designed for manned travel to Jupiter's moon, Callisto, and assessed that round trip journey. This engine, although unoptimized, produced 10 pounds force of thrust at a delivered specific impulse of 527,000 seconds for the entire 15-year mission while providing enormous amounts of electrical power to the spacecraft. A payload of 60 metric tons, included in the 300 metric ton vehicle, was carried to Callisto and back; the propellant tanks holding the 4 metric tons of fuel were not jettisoned in the process. The study concluded that the engine and spacecraft are within today's technology, could be built, tested, launched on several SLS (Space Launch System) (or similar) launchers, integrated, checked out, moved to an in-space base such as at a Lagrange point and operated for decades.

Engine

Trade Study: Storing NASA HDF5/netCDF-4 Data in the Amazon Cloud and Retrieving Data via Hyrax Server / THREDDS Data Server

As part of the overall effort to understand implications of migrating ESDIS data and services to the cloud we are testing several common OPeNDAP and HDF use cases against three architectures for general performance and cost characteristics. The architectures include retrieving entire files, retrieving datasets using HTTP range gets, and retrieving elements of datasets (chunks) with HTTP range gets. We will describe these architectures and discuss our approach to estimating cost.

HDF

Re-Organizing Earth Observation Data Storage to Support Temporal Analysis of Big Data

The Earth Observing System Data and Information System archives many datasets that are critical to understanding long-term variations in Earth science properties. Thus, some of these are large, multi-decadal datasets. Yet the challenge in long time series analysis comes less from the sheer volume than the data organization, which is typically one (or a small number of) time steps per file. The overhead of opening and inventorying complex, API-driven data formats such as Hierarchical Data Format introduces a small latency at each time step, which nonetheless adds up for datasets with O(10^6) single-timestep files. Several approaches to reorganizing the data can mitigate this overhead by an order of magnitude: pre-aggregating data along the time axis (time-chunking); storing the data in a highly distributed file system; or storing data in distributed columnar databases. Storing a second copy of the data incurs extra costs, so some selection criteria must be employed, which would be driven by expected or actual usage by the end user community, balanced against the extra cost.

data storage

Challenges in Obtaining and Visualizing Satellite Level 2 Data in GIS

Satellite data products are important for a wide variety of applications that can bring far-reaching benefits to the science community and the broader society. These benefits can best be achieved if the satellite data are well utilized and interpreted. Unfortunately, this is not always the case, despite the abundance and relative maturity of numerous satellite data products provided by NASA and other organizations. One way to help users better understand the satellite data is to provide data along with Images, including accurate pixel coverage area delineation, and science team recommended quality screening for individual geophysical parameters. However, there are challenges of visualizing remote sensed non-gridded products: (1) different geodetics of space-borne instruments (2) data often arranged in a long-track and a cross-track axes (3) spatially and temporally continuous data chunked into granule files: data for a portion (or all) of a satellite orbit (4) no general rule of resampling or interpolations to a grid (5) geophysical retrieval only based on pixel center location without shape information. In this presentation, we will unravel a new Goddard Earth Sciences Data and Information Services Center (GES DISC) Level 2 (L2) visualization on-demand service. The service's front end provides various visualization and data accessing capabilities, such as overlay and swipe of multiply variables and subset and download of data in different formats. The backend of the service consists of Open Geospatial Consortium (OGC) standard-compliant Web Mapping Service (WMS) and Web Coverage Service. The infrastructure allows inclusion of outside data sources served in OGC compliant protocols and allows other interoperable clients, such as ArcGIS clients, to connect to our L2 WCS/WMS.

GI

PDC19 Impact Exercise: Probabilistic Asteroid Impact Risk Assessment

Probabilistic Asteroid Impact Risk (PAIR) - PDC (Planetary Defense Conference) 2019 Hypothetical Exercise, NASA Ames, Asteroid Threat Assessment Project (ATAP) - Characterization Summary and Updates: Assessment date: 19 April 2027; Impact date: 29 April 2027 (10 days); Earth impact probability: 100 percent, New York Area; Diameter (meters): 60 plus or minus 10 (1 minus sigma), range 26–93; Energy: mean 11 megatons, range 650 kilotons to 46 megatons; Type: S class, remaining chunk of disrupted contact binary. Risk Summary: Affected population: mean 2.4 million, range zero to 10.2 million; Likely airburst at approximately16 kilometers altitude (8 to 29 kilometers); Blast overpressure is primary hazard; Damage out to approximately 70 kilometers if larger, lower burst; Little-to-no damage if burst is small and high.

Wheeler, Lorien

Assuring Intelligent Systems: Contingency Management for UAS

Unmanned aircraft systems (UAS) collaborate with humans to operate in diverse, safety-critical applications. However, assurance technologies need to be integrated into the design process in order to guarantee safe behavior, thereby enabling UAS operations in the National Airspace System (NAS). In this paper, formal methods are integrated with learning-enabled systems representations. The generation and representation of knowledge are captured via monadic second-order logic rules in the cognitive architecture Soar. These rules are translated into timed automata, and a proof of correctness for the translation is provided so that safety and liveness properties can be checked in the formal verification environment Uppaal. This approach is agnostic to the learning mechanism used to generate the learned rules (e.g., chunking, etc.). An example of a fault-tolerant, learning-enabled UAS deciding which of four contingency procedures to execute under a lost link scenario while overflying an urban area is used to illustrate the approach.

Intelligent Systems

The System Complexity Metric (SCM) Explains Systems Design and is Correlated with Cost and Failure Rate

The human short term memory span and working capacity is limited to three to five items, especially if they are organized complex “chunks” of information. The impression of complexity occurs when a system is simply difficult to understand, where there is no apparent pattern to predict its behavior. Hierarchical systems design can reduce perceived complexity and increase the amount of information that can be managed. The SCM was developed to measure complexity and help compare proposed overall system architectures before detailed design information is available. The SCM is defined as the sum of the number of major nodes, N, in the system block diagram plus the number of one-way interactions, I, between the nodes. SCM = N + I. SCM’s are easily determined by direct inspection of high-level block diagrams of life support systems. Axiomatic design develops a hierarchy of subsystem requirements and designs together in a top-down, back-and-forth process. A coupling matrix is used to control the relationships between the subsystem functions and design concepts. Axiomatic design can improve system design by decoupling requirements and designs. Axiomatic design was applied to the planning of a closed life support system, similar to that used on the International Space Station. A materially open as opposed to a closed system design was created by removing the interconnections required to close the system. The open system had the same number of designed subsystems as the closed system, but it had many fewer interconnections and its SCM was lower by about half. The costs were estimated and the MTBF (Mean Time Before Failure) tabulated for open and closed space life support systems. The estimated costs were linearly proportional to SCM for the wide variations of SCM in life support, but small differences may not be significant. The flight and preflight MTBF’s both declined exponentially with increasing MTBF, faster than MTBF-2, even though the preflight estimated MTBF’s were about ten times higher than the flight MTBF’s.

System Complexity Metric (SCM)

Degradation of Carbon Fiber Microstructures Due to Oxidative Etch Pitting

In order to understand the influence of etch pits on the material properties of carbon fiber microstructures, we use the Porous Microstructure Analysis (PuMA) software to create realistic pitted structures from virgin fiber structures and then analyze their degradation as the degree of pitting increases. For that purpose, we developed a pitting module within PuMA that creates pits with user-defined geometry (shape, size) and distribution (defect density) on the surface of arbitrary microstructures. In this work, we consider FiberForm microstructures, which are commonly used as the base material for ablative thermal protection systems (TPS). Using the new pitting module, we mimic the evolution of etch pits on FiberForm as it occurs from oxidation in ablative heating environments, by first importing the virgin FiberForm structure from a micrograph scan and then imposing different pitting conditions by varying pit radii and defect densities. We then leverage PuMA’s capabilities to calculate material properties for each structure. The results clearly show the degradation of thermal conductivity and structural integrity as etch pits grow, and furthermore highlight the complex evolution of the surface topology, which results in significant changes of the flowgeometry and chemical gas-surface interactions. Furthermore, a comparison of these changes with the case of shrinking fibers, which has heretofore been the standard for modelling ablation of carbon structures, yields significant differences. For example, we observe the formation of small chunks of fibers as pits grow in size, which could be released into the surrounding flow environment as spallation particles. This motivates us to continue our efforts of modelling pitting as an integral part of the structural degradation of carbon fiber structures in oxidation environments, which will ultimately improve our understanding of failure mechanisms in those materials.

PuMA