Results for “combustibility” — Page 4

DOE OSTI2021

Nitrogen evolution, NO X formation and reduction in pressurized oxy coal combustion

Oxy-combustion is one of the most prominent solutions for reducing CO 2 emissions from coal-fired power plants using carbon-capture-and-utilization technology. However, when compared to air combustion at atmospheric pressure, oxy-combustion is very expensive, owing to the significant efficiency penalties associated with air separation, flue gas recirculation (FGR), treatment, compression, and storage or transit of CO 2 . In comparison, pressurized oxy-combustion (POC) is more efficient as it recovers a significant amount of heat energy from the flue gas moistures. Nevertheless, CO 2 derived from pressurized oxy coal combustion has impurities, e.g., acid gases (NO X and SO X ) that can corrode the plant equipment, transport lines as well as deteriorating effect on the environment. Fortunately, in pressurized combustion systems, both NO X and SO X can be scrubbed by a single-column direct contact cooler (DCC), but this requires a minimum ratio of NO X to SO X at the inlet to be efficiently removed. Therefore, NOx is one of the important hindering parameters in commercializing the pressurized oxy-combustion. Although NOx evolution during oxy-coal combustion has been explored extensively at 1 atm, higher pressure studies are rare. Much still needs to be done to better understand the NO X mechanism and the effects of different parameters on NO X emissions under these conditions. Here, this paper reviews the published literature on nitrogen evolution, NO X formation and reduction in pressurized oxy-coal combustion. At higher pressures, the NO X from fuel-bound nitrogen is generated through volatiles, tar and char, all of which are discussed. Where literature is not available, the effect of pressure on NOx evolution in different stages of coal combustion is predicted through CHEMKIN simulation. Homogeneous and heterogeneous pathways of NO X formation and their destruction in pressurized oxy-coal combustion are evaluated. Additionally, the effect of pressure on a few mature and commercialized NOx abatement methods is explored. In the last, the future perspective and recommendation are given. This review will aid in the provision of basic knowledge about NOx evolution and control in pressurized fuel combustion, as well as the identification of new research areas to pursue.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2023

Low soot stoichiometric compression-ignition combustion

A combustion system including a combustion mechanism that injects oxygenated fuel into a combustion chamber. The oxygenated fuel mixes with the intake air in the combustion chamber where the air-fuel ratio in a portion of the combustion chamber is stoichiometric. The combustion mechanism includes an ignition mechanism that ignites the air-fuel mixture that generates a threshold number of particulates during combustion of the air-fuel mixture. The combustion system further includes an exhaust gas recirculation (EGR) device that recirculates a portion of the exhaust gases back into the combustion chamber. The EGR device recirculates the portion of the exhaust to lower combustion temperature resulting in reduced amount of nitrogen oxide in the exhaust. The combustion system further includes a three-way catalytic converter in line with the exhaust channel to convert a second portion of the exhaust gases, leading to lower pollutant emissions than conventional combustion systems.

Pickett, Lyle M.↗

DOE OSTI2025

Computational diagnostics and characterization of combustion recession in diesel sprays

While low-temperature combustion (LTC) strategies have been found to mitigate nitrogen oxides and particulate matter emissions in diesel engines, studies have also associated LTC with an increase in unburnt hydrocarbons. With more recent studies on diesel after end-of-injection (AEOI), combustion recession is identified as a phenomenon where at near nozzle region, high-temperature ignition (HTI) combustion can propagate back to the nozzle tip consuming the unburnt hydrocarbons AEOI. Current literature has suggested that combustion recession is controlled by auto-ignition. However, high-fidelity simulations and detailed analysis of such a mechanism are missing. In this study, comprehensive Large Eddy Simulations of a reacting spray at “Spray A” conditions are performed, where detailed analysis of combustion recession concerning flame morphology and propagation modes are included. In particular, this study demonstrated for the first time that while combustion recession is mainly auto-ignition dominated (consistent with the literature), a cool flame was found to deflagrate towards the richer regions of the mixture, promoting mixing and increasing the mixture temperature. This leads to HTI kernels, which then grow and develop as deflagrative waves, therefore sustaining the combustion recession process. The study also detailed the extinction mechanism of combustion: the entrainment wave will overlean the near-nozzle mixtures, rendering it unable to support HTI, which leads to the extinction of the upstream flame AEOI in lower reactivity mixtures. Combustion recession is also observed to be contingent on the chemical and diffusion processes, even at low scalar dissipation rates. Finally, a new criterion for combustion recession based on chemical explosive mode is proposed and validated with previous combustion recession index to quantify the extent of HTI in near-nozzle mixtures AEOI. The newly developed metric combined with a previous experimentally-based metric can provide simple but valuable measurements of the degree and propensity of the upstream flame AEOI.

CEMA↗

DOE OSTI2024

Development of prechamber enabled mixing-controlled combustion strategy for ultra-low methane emissions from lean burn natural gas engines

This numerical study explores the optimization of Prechamber Enabled Mixing-Controlled Combustion (PC-MCC) using natural gas in heavy-duty engines, aiming to enhance combustion efficiency to minimize methane slip and NOx emissions. The approach involves a prechamber ignition system, distinct from conventional spark ignition (SI) systems, to initiate combustion of direct injected natural gas. By leveraging the robust ignition characteristics of the prechamber, the PC-MCC method demonstrates significant potential in achieving efficient combustion akin to diesel engines but with lower greenhouse gas emissions. The research evaluates the effects of various geometric and operational parameters on the combustion process and emissions, including prechamber volume, nozzle diameter, direct injector (DI) geometry, and engine operating strategies. Computational Fluid Dynamics (CFD) simulations are utilized, focusing on a heavy-duty, single-cylinder engine modeled after the Caterpillar C9.3B engine. Key findings indicate that a prechamber volume of 3 cc, coupled with a nozzle diameter of 2.75 mm for two prechamber holes, strikes an optimal balance between combustion efficiency and emissions reduction. This configuration ensures robust combustion across a range of operating conditions while maintaining methane slip within targeted limits. Further investigation into DI geometry shows the significance of the injector umbrella angle and nozzle diameter in shaping the fuel-air mixing and combustion dynamics. An umbrella angle of 130° and a nozzle diameter of 300 microns are identified as optimal, promoting rapid and efficient combustion with minimized methane and NOx emissions. The study also investigates the impact of injection timing and pressure, highlighting their roles in controlling combustion timing and influencing emissions levels. Advanced injection timing is found to be crucial in achieving the desired low methane slip, whereas retarded injection timing assists to reduce NOx emissions while having a slight increase in methane emissions. Operating strategies incorporating various levels of Exhaust Gas Recirculation (EGR) are assessed for their effectiveness in further reducing emissions. The research demonstrates that a judicious combination of internal hot EGR and careful calibration of DI pressure and SOI timing can achieve significant reductions in NOx emissions while keeping methane slip under control. Specifically, an internal EGR level of 15%–25%, combined with DI pressures of 200–300 bar and injection timings at or after top dead center, is recommended. These findings contribute valuable insights into the development of advanced combustion techniques for natural gas engines, offering a viable pathway to reduce methane slip without compromising engine efficiency or performance. The PC-MCC system presents a promising solution for the future of heavy-duty natural gas engine technology to reduce methane emissions.

Nsaif, Osama↗

DOE OSTI2020

Operation and turndown of a segmented annular combustion system

The present disclosure is directed to the operation and turndown of a segmented annular combustion system. The method includes injecting, via a fuel nozzle, a combustible mixture into a primary combustion zone between an adjacent pair of integrated combustor nozzles and burning the combustible mixture. The method further includes flowing air and injecting fuel into a premixing channel defined within a first integrated combustor nozzle to produce a second combustible mixture. The second combustible mixture is injected into a secondary combustion zone where it is combusted. The flow of combustion gases is accelerated, via turbine nozzles of the integrated combustor nozzles, toward turbine blades of a downstream turbine section. The method permits turndown of the combustion system by reducing or shutting off fuel to various components of the combustion system.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Experimental study and demonstration of pilot-scale, dry feed, oxy-coal combustion under pressure

In this paper, we discuss how pressurized oxy-combustion is a promising technology for low-carbon, fossil fuel utilization. It has the potential of improved efficiency and economics compared with conventional atmospheric pressure oxy-combustion. Washington University in St. Louis has proposed a new pressurized oxy-combustion process, namely Staged Pressurized Oxy-Combustion, which has the potential to improve further the plant efficiency, operational flexibility, and economics. This process burns pulverized coal in a pressurized, oxy-combustion environment, which has not been demonstrated in a pilot-scale system before. To address this gap, a 100 kWth pressurized oxy-combustion facility was designed and constructed. This facility has a unique burner and furnace design featuring a co-axial, low-mixing flow field, which is drastically different from conventional coal-fired boiler designs where strong mixing is sought by introducing swirl or recirculating flows. This work aims to present the first pilot-scale experimental results of a dry-feed, pressurized oxy-combustion system. The tests focused on exploring flame stability and shape, char burnout, and fine particulate matter formation. Testing results suggest that the burner has excellent flame stability. The flame shape is consistent with the design philosophy and agrees with large eddy simulations. Importantly, complete char combustion can be achieved with an oxygen mole fraction in the flue gas of only 0.8%, as opposed to a required value of ~3% for conventional atmospheric pressure air-fired or oxyfuel combustion, which reduces the costs of both oxygen generation upstream and oxygen removal downstream. The testing results show promise for dry-feed, pressurized oxy-combustion, and the new burner and furnace design.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

CFD modeling of near-wall combustion and unburned methane prediction in natural gas spark ignition engines

Natural gas-powered engines play a critical role in gas drilling, compression, and transmission sectors, but methane (CH 4 ) from engine combustion slip can be significant over their lifespan, contributing to atmospheric pollution and signaling reduced engine efficiency. Here, to address this challenge, computational fluid dynamics (CFD) simulations offer valuable insights into the in-cylinder combustion process, enabling the optimization of combustion strategies and engine designs to minimize unburned CH 4 slip. This study aims to evaluate and improve combustion models for simulating the combustion process and predicting unburned CH 4 concentrations in natural gas spark-ignition (SI) engines, including engines that are part of combined reformer-engine systems. Specifically, the performance of two flamelet-based combustion models—the Extended Coherent Flame Model (ECFM) and the G-equation model—was assessed using experimental engine data collected under varying excess-air ratio (λ) conditions and fuel compositions, including natural gas and syngas blends. In addition, to enhance the predictive capabilities of the G-equation model, a flame-wall interaction (FWI) sub-model was integrated into its framework. The effects of its model parameters, such as quenching and influence distance, on combustion behavior and unburned methane predictions were analyzed in detail. The ECFM tended to predict delayed combustion phasing under diluted mixture conditions, resulting in overprediction of unburned CH 4 concentrations. In contrast, the G-equation model provided reasonable predictions of combustion pressure, while representing higher the CH 4 reduction rate across the operating condition compared to experimental data. Incorporating the FWI sub-model—with the quenching distance calculated based on a pressure-dependent relation (P -0.48 ) and a fixed influence distance of 1.5 mm—further improved the G-equation model’s accuracy in predicting CH 4 reduction rates without compromising its ability to simulate the combustion process.

Combustion model↗

DOE OSTI2022

Impact of Fuel Properties on the Combustion of Late Post Injections used for Aftertreatment Thermal Management

Typical calibration for catalyst thermal management for compression-ignition engines involves delaying the post-injection into the expansion stroke. Reduced work extraction due to the late heat release event is used to increase the exhaust gas temperature to shorten the time associated with reaching optimal temperatures for aftertreatment systems. Shorter catalyst heat-up time can simultaneously reduce tail-pipe emissions and the typical fuel penalties associated with this mode of operation. In this study, the effects of volatility, reactivity, and oxygen content of the fuel on combustion stability and emissions were studied in a light-duty single-cylinder research engine. Blends of iso-octane/ n-heptane and farnesane/ 2,2,4,4,6,8,8-heptamethylnonane were used to study the impacts of volatility and reactivity. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility. On the other hand, increased reactivity improved combustion stability and efficiency at late injection timings (+24 CAD). The combined effect of increase in chemical reactivity and oxygen content was analysed by comparing the baseline #2 diesel operation with two blends of mono-ethers and #2 diesel to achieve cetane numbers (CNs) of 45 and 55, and a pure blend of mono-ether components with CN > 100. Fuels with higher reactivity and oxygen content were found to reduce engine-out hydrocarbon and carbon mono-oxide emissions while also achieving stable combustion at post-injection timings later than those achievable with diesel fuel. The pure ether-blend had the latest achievable post-injection timing (≥+26 CAD) while still maintaining stable combustion. At similar combustion stability, the pure ether blend was found to have 2.8% higher combustion efficiency and 4.3% higher thermal efficiency than the baseline diesel. The ether-diesel blends at CN45 and CN55 were found to have 1.8% higher combustion efficiency than baseline diesel. The results demonstrate that fuels with increased reactivity can increase combustion efficiency, reducing carbon monoxide and hydrocarbon emissions, while maintaining similar exhaust temperature and combustion stability compared to baseline diesel. Further greenhouse gas benefits can also be realized as the mono-ether bioblendstocks show potential for >50% reduction in greenhouse gas emissions relative to diesel fuel based on their production method.

99 GENERAL AND MISCELLANEOUS↗

DOE OSTI2021

Large Eddy Simulation of Lean Mixed-Mode Combustion Assisted by Partial Fuel Stratification in a Spark-Ignition Engine

Partial fuel stratification (PFS) is a promising fuel injection strategy to improve the stability of lean combustion by applying a small amount of pilot injection right before spark timing. Mixed-mode combustion, which makes use of end-gas autoignition following conventional deflagration-based combustion, can be further utilized to speed up the overall combustion. In this study, PFS-assisted mixed-mode combustion in a lean-burn direct injection spark-ignition (DISI) engine is numerically investigated using multi-cycle large eddy simulation (LES). A previously developed hybrid G-equation/well-stirred reactor combustion model for the well-mixed operation is extended to the PFS-assisted operation. The experimental spray morphology is employed to derive spray model parameters for the pilot injection. The LES-based model is validated against experimental data and is further compared with the Reynolds-averaged Navier–Stokes (RANS)-based model. Overall, both RANS and LES predict the mean pressure and heat release rate traces well, while LES outperforms RANS in capturing the cycle-to-cycle variation (CCV) and the combustion phasing in the mass burned space. Liquid and vapor penetrations obtained from the simulations agree reasonably well with the experiment. Detailed flame structures predicted from the simulations reveal the transition from a sooting diffusion flame to a lean premixed flame, which is consistent with experimental findings. LES captures more wrinkled and stretched flames than RANS. Finally, the LES model is employed to investigate the impacts of fuel properties, including heat of vaporization (HoV) and laminar burning speed (SL). Combustion phasing is found more sensitive to SL than to HoV, with a larger fuel property sensitivity of the heat release rate from autoignition than that from deflagration. Moreover, the combustion phasing in the PFS-assisted operation is shown to be less sensitive to SL compared with the well-mixed operation.

fuel property sensitivity↗

DOE OSTI2020

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2021

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

pressurized oxy-coal combustion, sub-micron ash ae↗

DOE OSTI2022

Characterizing Impacts of Dry Coal Feeding in High Pressure Oxy-Coal Combustion Systems

Reaction Engineering International (REI) has managed a team of experts from the University of Utah, Southeast University (SEU) in Nanjing, China, Electric Power Research Institute (EPRI), Corrosion Management Ltd. (C-M), Praxair, and Brigham Young University (BYU) to investigate dry pulverized coal feeding for pressurized oxy-coal combustion. Dry feed firing systems for entrained flow, pressurized, oxy-coal combustors have not been well developed, although related technologies have been used in the Shell Gasification Process and for pressurized fluid bed combustion. DOE-funded research recently completed at REI and the University of Utah focused on characterizing impacts of high temperatures and pressures in oxy-coal combustion systems. For high pressure combustion, that research used a coal slurry feed into a 17 bar pressurized combustor. As a consequence of that research, it was identified that fuel feeding and firing system flexibility are challenges that require attention. Based on that experience, the approach of using a coal slurry feed system leads to challenges in producing consistent atomization of the slurry, which causes burnout problems, especially at high pressures. In addition, slurry atomization processes may be difficult to scale to sizes appropriate for practical commercial use. Dry pressurized coal burner systems, on the other hand, have the potential to yield efficiency gains, improve flexibility and facilitate applications at larger scales. Experimental work was conducted at the University of Utah Industrial Combustion and Gasification Research Facility as well as the 100 kW pressurized oxy-coal combustor (POC) facility at Brigham Young University. Mechanism development and CFD-based combustion and dense-phase flow modeling were performed at REI. Successful completion of the project objectives has resulted in the following key deliverables: 1) Design and prototype of a pressurized pulverized coal feeding and oxy-firing system 2) Data from a 100kW, pressurized (15 bar) entrained flow reactor with a dry feeding delivery and burner system that describes flame characteristics, radiative heat flux profiles, carbon burnout, along with characteristics of ash aerosols, fouling, and slagging. 3) Validated and transportable models that describe the relevant conditions in pressurized oxy-combustion systems and that can be used for scale-up and optimization. 4) Principles to guide design of high pressure, pilot-scale and full-scale coal oxy-firing systems. 5) Assessment of pressurized oxy-combustion impacts on key parameters relevant to oxy-coal fired utility boilers such as coal devolatilization, char oxidation, mineral matter transformation, deposition, and corrosion. The experimental data, pressurized oxy-firing system principles, and process mechanisms provided by this work can be used by electric utilities, boiler OEMs, equipment suppliers, design firms, software vendors, consultants and government agencies to assess the use of high temperature and high pressure oxy-combustion in current research and to guide development of new oxy-coal boiler designs.

01 COAL, LIGNITE, AND PEAT↗

DOE OSTI2025

Mixing-Controlled Combustion of Ethanol Enabled by Prechamber Ignition (PC-MCC): A Preliminary Experimental Demonstration

This experimental study presents preliminary investigations of prechamber-enabled mixing-controlled combustion (PC-MCC) at −2 bar brake mean effective pressure (BMEP) and 2200 rpm with fuel-grade ethanol (E98). Experimental results are conducted on a prechamber retrofitted single-cylinder Caterpillar C9.3B test engine. First, a series of prechamber-only experiments were conducted with a motored engine to evaluate the salient combustion trends in response to relevant prechamber operating parameters. Under firing conditions, the prechamber operating strategy was assessed with respect to the impact on ignition assistance of direct-injected E98 and overall engine performance. The preliminary results indicate the jet-induced ignition process is robust and prompts diffusion combustion of E98 at diesel-like boundary conditions. Here, the effect of external exhaust gas recirculation (EGR) on the residual tolerance of the prechamber combustion process was also investigated and showed stable combustion in both the main chamber and prechamber up to 30% EGR. Experiments were also conducted with the stock diesel engine for baseline comparison. At matched combustion phasing, mixing-controlled combustion of ethanol enabled by prechamber ignition was able to achieve heightened gross thermal efficiency while simultaneously reducing NOx and practically eliminating smoke emissions relative to diesel combustion. In addition, the covariance of load and standard deviation of combustion phasing was diesel-like and less than 2% and 1 CAD, respectively.

PC-MCC↗

DOE OSTI2023

An Experimental Comparison of Cyclic Variations in Diesel–Natural Gas and POMDME–Natural Gas Dual Fuel Combustion

Abstract Cyclic variations in internal combustion engines are caused by various factors, including combustion mixture stratification, in-cylinder flows, local fluctuations in air-fuel ratio, etc. Cyclic variations have a profound impact on engine performance and emissions. In this study, cyclic variations in dual fuel combustion are analyzed, comparing diesel–natural gas (NG) and polyoxymethylene dimethyl ether (POMDME)-NG dual fuel combustion. Cyclic variability was initially quantified using the coefficient of variation of gross indicated mean effective pressure (IMEPg) computed from experimental cylinder pressure data. The cases analyzed in this study had a coefficient of variation (COV) of IMEPg greater than or around 5%, which was the lower limit of onset of instability for this engine. Experiments were performed at two fixed start of injection (SOI) of high-cetane fuel: 310 CAD and 350 CAD. For all experiments, a constant load of 5 bar IMEPg was maintained, and the intake boost pressure and rail pressure were fixed at 1.5 bar and 500 bar, respectively. For each case, 1000 cycles of cylinder pressure data were recorded, filtered, and processed using an in-house heat release analysis code for each cycle. A comparison between individual cycles and the “ensemble averaged cycle” was made for both diesel–NG and POMDME–NG combustion. For the early SOI of 310 CAD, the peak cylinder pressure fluctuations of individual cycle were found to be ± 15 bar for both fuel combinations, compared to the ensemble averaged cycle, and < 1/10th of the cycles had an IMEPg lower than 0.05 bar of the ensemble averaged cycle. However, the peak pressure fluctuations were found to be lower for POMDME–NG (±3 bar) than diesel–NG dual fuel combustion at 350 CAD SOI, indicating lower cyclic variations. The higher reactivity of POMDME helped reduce fluctuations in combustion phasing at the retarded SOI. The presence of cycles of deterioration and cycles of recovery were also observed with diesel–NG combustion for 310 CAD SOI, and the scatter in the IMEPg return map was similar for both fuel combinations. The IMEPg return map for POMDME–NG combustion was less scattered at the 350 CAD SOI.

Engineering↗

DOE OSTI2020

Radiant boiler for pressurized oxy-combustion and method of radiant trapping to control heat flux in high temperature particle-laden flows at elevated pressure

A boiler has a shell surrounding a vertical centerline. The shell defines an inner surface having an inner diameter and an inner length extending between an upper upstream end and a lower downstream end. The inner surface defines a hollow interior, the boiler having a pre-combustion zone, a combustion zone downstream from the pre-combustion zone, and a post-combustion zone downstream from the combustion zone. The shell is tapered outward along its length in at least a portion of the combustion zone. An oxidizer inlet is in fluid communication with the pre-combustion zone, and a fuel nozzle introduces fuel into the combustion zone. A tube assembly is mounted in the hollow interior of the shell for transferring heat to fluid flowing through the tube assembly. A flue duct is in fluid communication with the post-combustion zone for transporting flue gases from the hollow interior.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2023

Cost-constrained adaptive simulations of transient spray combustion in a gas turbine combustor

Predictive high-fidelity simulations of turbulent spray combustion must capture the combined effects of complex chemistry, multiphase evaporating flow and spray-flame interactions to achieve physical accuracy. Finite-rate chemistry (FRC) combined with a realistic chemical mechanism is a combustion model well-suited for this purpose, but has a high computational cost due to the large number and stiffness of transported chemical species. In contrast, flamelet-based models achieve lower cost by transporting a small number of quantities of reduced stiffness, but assumptions regarding local flame topology, boundary conditions and inter-phase coupling limit their physical accuracy. Recently, the Pareto-efficient combustion (PEC) framework was developed to dynamically assign combustion models based on local cost and accuracy metrics in gas-phase reacting flows. In this work, we extend this PEC framework to spray combustion through the rigorous analysis of the multiphase coupling terms in the governing equations. The derivation shows that spray evaporation causes errors in the prediction of species mass fractions for flamelet-based models due to the sensitivity of the local thermo-chemical state to changes in composition caused by fuel vaporization across combustion regimes present in practical spray combustion devices. Sub-model assignment is formulated as a multiple-choice knapsack problem, where computational cost is directly controlled through the fraction of the domain assigned to the FRC sub-model. The extended PEC formulation is applied to the simulation of a realistic rich-quench-lean gas turbine combustor at steady-state conditions, as well as transient operation resulting in lean blow-out (LBO). Analysis of transient simulations during LBO demonstrates the extended PEC formulation’s capacity to dynamically adapt to changing conditions within the combustor. Transient combustor dynamics are shown to approach convergence with limited increases in computational cost, while retaining substantial computational cost reduction compared to monolithic FRC simulations. Through PEC simulations with increasing fractions of the domain assigned to FRC, monolithic flamelet simulations are shown to over-predict flame stability during LBO. Finally, the extended PEC formulation is thus shown to overcome deficiencies of monolithic models by controlling modeling error for multiphase combustion modeling.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2026

Flame Chemistry Workshop: a perspective on challenges and strategic actions in combustion experiments and chemical kinetics modeling

Continued progress in the development of predictive models for combustion chemistry—including ignition and flame behavior, species evolution, and combustion system performance—relies on overcoming enduring and emerging challenges in experimental measurements, theoretical formulations, and chemical kinetics mechanism construction. As combustion science continues to coincide with advances in sustainable fuels development, plasma technologies, and automated modeling capabilities, the need for coordinated, community-driven strategies is essential. The Flame Chemistry Workshop (FCWS), held biennially before the International Symposium on Combustion, serves as a dedicated platform to identify, consolidate, and address these challenges in a structured and collaborative manner. This perspective arises from discussions at the 7th FCWS in Milan, Italy (2024), and presents a collective view of the critical barriers currently limiting progress. Across the five technical domains discussed during the 7th FCWS – sustainable fuels combustion, advanced diagnostics for combustion measurements, experiments and modeling in plasma combustion, artificial intelligence and automated methods for theory and mechanisms generation, and chemical kinetic models—a series of persistent and emerging scientific challenges were identified, highlighting the need for deeper integration between three areas: theory, experiments, and modeling. In conclusion, the present article concisely describes present challenges that were identified in each of the technical domains in an effort to streamline and coordinate solutions to accelerate progress in combustion science.

Chemical kinetics↗

DOE OSTI2024

Numerical investigation of equivalence ratio effects on Flex-Fuel mixing controlled combustion enabled by prechamber ignition

There is interest in adapting renewable and low-carbon intensity fuels to heavy-duty engines to help displace criteria and greenhouse gas emissions associated with diesel combustion. Low-carbon fuels have inherently low cetane numbers and thus pose a significant challenge when considering direct substitution in diesel combustion systems. Use of an actively fueled prechamber as an ignition source to initiate mixing-controlled combustion (PC-MCC) of low-cetane fuels is becoming an attractive combustion mode to alleviate the identified reactivity deficit. This work focuses on the utilization of an active prechamber to facilitate diesel-like combustion of bioethanol-gasoline fuel blends in a heavy-duty engine. Recent results in this emerging technology suggest that ignition quality is uniquely coupled to prechamber equivalence ratio. In this numerical study, the fundamental implications of prechamber equivalence ratio on the ignition performance of direct injected fuels ranging from E10 to E100 are investigated using CONVERGE. Parametric studies of the prechamber operating strategy were assessed at diesel-like conditions to characterize the performance trends relative to a diesel baseline at the same boundary conditions. Simulation results indicate that PC-MCC is flex-fuel capable and achieves diesel-like ignition qualities and combustion processes for all fuels considered under stoichiometric and rich prechamber conditions. To characterize the equivalence ratio trends observed, a novel inflow boundary modeling technique was utilized to prescribe turbulent jets in place of the prechamber where selective speciation of the jet composition was conducted to isolate the ignition contributions of radical and reacting species in lean, stoichiometric, and rich jets. The inflow boundary modeling suggests that excess fuel and combustion intermediates present in jets produced from stratified and fuel-rich prechamber operation promotes higher jet temperatures and as such are superior ignition sources. Relative to a lean prechamber jet, the peak temperature of a reacting jet from a rich prechamber was up to 600 K hotter at fixed distances from the orifice exit. Furthermore, radicals also demonstrated an influence on the ignition process, but the combustion mode was identified to be thermally dominant.

33 ADVANCED PROPULSION SYSTEMS↗