Search NASA⌕ Search

SEARCH · Search NASA

Results for “contact angle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Rejection of malathion by nanofiltration and reverse osmosis membranes exposed to foulant and two clean-in-place procedures

This research tested the treatment efficacy of an Energy Savings Nanofiltration 1 Low Fouling (ESNA 1-LF) nanofiltration (NF) and an Energy Saving Polyamide 2 (ESPA2) reverse osmosis (RO) membrane for removing malathion from water. Both membranes are of composite polyamide construction. The study included measuring malathion rejection using both pristine membranes and membranes exposed to a simulated secondary wastewater effluent foulant before and after two types of clean-in-place procedures. Across all conditions studied, malathion rejection ranged from 84 to 95% for the ESNA1-LF NF membrane and 77 to 94% for the ESPA2 RO membrane. Contact angle measurements were also collected for each membrane exposure condition. While the contact angle measurements indicated changes to the hydrophobicity of the selective layer of the membranes, they did not correlate to changes in the performance of malathion rejection. As expected, it was observed that malathion rejection improved with the introduction of foulant. Also, the clean-in-place procedures helped restore flux while maintaining malathion rejection.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Experimental investigation into coal wettability changes caused by reactions with scCO 2 -H 2 O

Geological CO 2 sequestration (GCS) can help mitigate global warming and enhance methane recovery from coal beds. However, few studies have linked the effects of CO 2 to surface chemistry changes controlling wetting behavior in deep coal beds. Contact angles (CAs) of CO 2 /N 2 -high volatile bituminous coal-water systems were measured under different temperatures and pressures. The surface chemistry and physical structure of coals were characterized to investigate changes in physicochemical properties and their relations with wettability after reactions. For N 2 treatment, the time-dependence of static and dynamic CAs were insignificant, ranging within 4°. For gaseous CO 2 treatment, the static CAs and the average advancing angles increased slightly. With supercritical (sc) CO 2 , both the static and dynamic CAs increased significantly, and θ adv changed to intermediate-wet (92°). Reactions with minerals exposed to scCO 2 resulted in greater surface roughness and heterogeneity, greater contact angle hysteresis and more surface sites occupied by scCO 2 rather than H 2 O. Increases in hydrophobic functional groups and decreases in hydrophilicity were shown by FTIR spectra, reflecting the shedding of polar oxygen-containing functional groups, reduction of hydrogen bonds, and increasing percentage of hydrocarbons. XRD patterns obtained following scCO 2 -treatment showed that crystallite growth and molecular polymerization were higher toward graphite-like. The calculated structural parameters of functional groups and crystallites both showed elevated coal rank. Changes in crystallite structure, notably higher carbon content and decreased negative surface charge, are unfavorable for water-wetting. Finally, this study contributes to understanding surface chemistry changes responsible for decreased wettability during CO 2 -enhanced coal bed methane recovery and GCS in coal reservoirs.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Absorber Column CFD model validation against PNNL’s device-scale absorber column on the LCFS unit

Absorber column has been widely used for CO 2 capture in the coal-fired power plants. High-fidelity CFD models play an important role in absorber column design and solvents optimization, which help enhance the CO 2 capture efficiency and reduce the operation cost. This report provides a comprehensive description of the development of CFD absorber models at two different levels, the design and implementation of PNNL’s device-scale absorber column experiment, and the methodology to combine the CFD results, experiment data, and Aspen model for a better understanding of the interface area in packed column. A composite model is firstly proposed in the Discrete Element Method (DEM) packing process, which can model the complex geometry of various packing elements. This generates a realistic packing pattern and accurate packing porosity ε and specific area a p compared to the actual values for absorber column used in LCFS. Two level of CFD absorber models were developed, namely the full-size column model (FCM) to simulate the entire packed column with a focus on the wall/entrance effects, and the representative column model (RCM) to simulate a section of column with a focus on the sensitivity study of interface area. A Design of Experiment (DoE) plan was developed to guide the collection of 100 run CFD data and 12 experiment runs. The 100 CFD runs were carried out in the RCM with Pro-Pak packing and cover a wide operation range and solvent properties. Impact of influential factors on the interface area in packed column were investigated in details. The CFD interface area was then combined with the experimental data and Aspen model to infer some information of the effective contact angle in the column. The accuracy and uncertainties in the interface area and contact angle can be quantified.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2022

Development of a Flotation Simulator That Can Predict Grade vs. Recovery Curves from Mineral Liberation Data

Flotation is a kinetic process designed to separate mineral fines by control of hydrophobicity. In general, both the recovery and selectivity of a flotation process increase with contact angle. It is difficult, however, to model flotation kinetics using the thermodynamic parameter. In the present work, we consider flotation as heterocoagulation so that the bubble-particle interactions occurring in the pulp phase of a flotation cell can be modeled using the hydrophobic force as a kinetic parameter that can represent the role of contact angles in flotation. Here, the pulp-phase model developed in this manner has been combined with a froth-phase model developed earlier by considering the effect of particles in film thinning kinetics and bubble coarsening (Park et al, 2018). The combined model has been used to develop a flotation simulator that can be used to construct grade vs. recovery curves from feed characteristics (e.g., mineral liberation and particle size) and various operating parameters. The simulator has been tested successfully against a set of bench-scale continuous flotation test results reported in the literature (dos Santos and Galery, 2018).

58 GEOSCIENCES↗
DOE OSTI2023

Graphite-Salt Interactions: Summary of FY23 Activities

This report summarizes the research activities related to graphite–molten salt interactions during FY 2023. It includes results of FLiNaK infiltration experiments under various operating conditions, such as different temperatures, pressures, and times, to understand the effect of each condition on a variety of nuclear-grade graphites. Six graphite grades with various origins and properties were selected for the intrusion experiments using molten FLiNaK. The effect of intrusion pressure, temperature, and time were evaluated by measuring weight uptake, and the extent of penetration was studied using neutron tomography (n-CT). In addition, the wetting behavior of molten FLiNaK on a graphite surface was studied by measuring the contact angle on various grades of graphite. The results obtained by n-CT and contact angle measurements will help advance the understanding of factors that control the salt penetration in graphite and their relationship with intrinsic structural properties of the various graphite grades.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Determination of the Interfacial Energy between Graphene Nanoplatelets and Deuterated or Hydrogenated Polystyrene

The tracer diffusion coefficients of various graphene nanoplatelet-polystyrene (GNP-PS) systems were determined by using dynamic secondary ion mass spectrometry, which provided insights into the interactions within the polymer nanocomposite system. Bilayer films, where one contained trace amounts of deuterated polystyrene (dPS), were produced, and the interdiffusion was measured by detecting the position of the dPS interface. GNPs were placed in both or only one of the two layers. The diffusion coefficient was decreased when GNPs were present in both layers as compared to the samples without GNP, indicating an attractive interaction between GNP and polystyrene. Surprisingly, the coefficient increased relative to the control when GNPs were present only in the PS containing layer, whereas it decreased most strongly when GNP and dPS were present only in the same layer, indicating that an additional preference existed for GNPs and dPS. A significant difference in interfacial energies was measured using contact angle goniometry of PS or dPS droplets on flat GNP layers, confirming the preferential interaction. DFT calculations were used to calculate the interfacial interaction between GNP and dPS or PS, and they showed an attractive potential which was maximal when the PS rings were conformal with the GNP structure. Furthermore, the differential energy between PS and dPS at the GNP interface was in excellent agreement with the measured value. In contrast, contact angle goniometry indicated that the interaction between GNP and poly(methyl methacrylate) (PMMA) was unfavorable, and no difference in interfacial energy between dPMMA and PMMA was observed. Therefore, these techniques can provide a means for determining the relative affinity between GNP and different polymer hosts, which can be an important consideration in the mechanics and adhesion properties of the compounds.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Superhydrophilicity of $α$-alumina surfaces results from tight binding of interfacial waters to specific aluminols

Understanding the microscopic driving force of water wetting is challenging and important for design of materials. The relations between structure, dynamics and hydrogen bonds of interfacial water can be investigated using molecular dynamics simulations. Here, contact angles at the alumina (0001) and ($11\bar{2}0$) surfaces are studied using both classical molecular dynamics simulations and experiments. To test the superhydrophilicity, the free energy cost of removing waters near the interfaces are calculated using the density fluctuations method. The strength of hydrogen bonds is determined by their lifetime and geometry. Both surfaces are superhydrophilic and the (0001) surface is more hydrophilic. Interactions between surfaces and interfacial waters promote a templating effect whereby the latter are aligned in a pattern that follows the underlying lattice of the surfaces. Translational and rotational dynamics of interfacial water molecules are slower than in bulk water. Hydrogen bonds between water and both surfaces are asymmetric, water-to-aluminol ones are stronger than aluminol-to-water ones. Molecular dynamics simulations eliminate the impacts of surface contamination when measuring contact angles and the results reveal the microscopic origin of the macroscopic superhydrophilicity of alumina surfaces: strong water-to-aluminol hydrogen bonds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Interfacial Chemistry Involved in Selective Separation of NMC/LMO and LCO/LMO Binary Cathode Materials by Froth Flotation Using Oleic Acid

The variability in cathode compositions within recycled lithium-ion battery (LIB) feedstocks poses a significant challenge to efficient downstream refining processes. This study demonstrates the feasibility of using froth flotation with oleic acid as a collector to selectively separate lithium nickel-manganese-cobalt oxide (NMC) and lithium cobalt oxide (LCO) from lithium manganese oxide (LMO) materials. Laboratory-scale flotation tests achieved an 80% separation efficiency in a single stage, producing a froth product with >90% purity of NMC/LCO at approximately 90% yield. Concurrently, the LMO materials were enriched in the sink product with ∼90% purity and ∼90% yield. This approach was further validated using recycled cathode materials, confirming its applicability to realistic feedstocks. The underlying mechanism governing the selective separation of NMC/LCO from LMO was investigated using ζ-potential measurements, contact angle measurements, bubble-particle attachment experiments, and X-ray photoelectron spectroscopy (XPS) analysis. Both contact angle and bubble-particle attachment results confirmed that oleic acid adsorption rendered NMC and LCO surfaces hydrophobic, thereby enhancing flotation recovery. At pH 5, oleic acid adsorbed preferentially onto NMC and LCO surfaces via electrostatic interactions, while exhibiting minimal adsorption on LMO surfaces. However, separation efficiency deteriorated at higher pH, which was attributed to the co-flotation of LMO materials caused by oleate chemisorption on MnOH + species. This work establishes froth flotation as a viable cathode/cathode separation strategy, providing a low-cost, scalable pathway to preconcentrate and enrich nickel-rich and cobalt-rich cathode active materials from incompatible cathode chemistries for direct recycling or hydrometallurgical processing. Furthermore, this study reveals, for the first time, the mechanism of oleate adsorption on the surface of different cathode materials.

PH↗
DOE OSTI2025

Thermal evaporation of thin Li films

Thermal evaporation of lithium is considered a promising technique for the fabrication of clean lithium thin films for solid-state batteries. Here, in this study, we present a practical investigation of nanometer scale lithium films prepared by evaporation on different substrates. These substrates include Li-alloying and nonalloying metals as well as different classes of solid-state lithium-ion conductors. The deposition rate was also varied. For films less than 100 nm thick, the data show that the deposition rate has the biggest impact on the surface coverage. At 50 Å/s, Li forms small particles <1 μm in diameter while higher deposition rate of 150 Å/s resulted in more uniform film morphology on all the substrates. At the lower deposition rates, the wetting of Li to the substrate will impact the particle morphology. We also used the particles to estimate a contact angle between Li and the substrate to qualitatively compare the adhesion from substrate to substrate. The smallest contact angle was observed from lithium films on Li 7 La 3 Zr 2 O 12 and LiPON (nominal Li 2.94 PO 3.5 N 0.31 ) solid-state electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Pool boiling critical heat flux studies of accident tolerant fuel cladding materials

Pool boiling experiments have been performed at atmospheric pressure on potential accident tolerant fuel (ATF) cladding materials (Zirlo®, Cr coated Zirlo®, FeCrAl coated Zirlo®, and monolithic SiC) to evaluate the Critical Heat Flux (CHF) points. Corrosion resistant coatings of Cr and FeCrAl alloy were deposited on flat Zirlo® samples using cold spray technology. The as-prepared samples after uniform surface polishing were subjected to autoclave tests at 360 °C water and 18.6 MPa for 360 h to simulate prototypic corrosion of the ATF cladding materials in LWR normal operation. Surface characteristics potentially influencing CHF such as surface morphology, roughness, static contact angle, and surface chemistry were characterized using a suite of characterization methods including scanning electron microscopy, 3D optical profilometry, optical contact angle measurements, and x-ray photoelectron spectroscopy (XPS). Thermo-physical properties of the samples such as density, thermal conductivity, and heat capacity were measured by differential scanning calorimetry and laser flash thermal diffusivity measurement. FeCrAl coatings showed CHF values comparable to bare Zirlo® samples, while slightly lower CHF values were observed for Cr coated samples and bulk SiC flats (produced by chemical vapor deposition, CVD). As-deposited Cr coatings showed 67% higher CHF than the as-polished Cr coatings due to its higher surface roughness level. The autoclave testing for the prepared samples generally increased the CHF except for the surface polished Cr coatings. Similar CHF values of bare Zirlo®, FeCrAl coating, and CVD SiC samples were observed after autoclave test but there were negligible change CHF of Cr coatings. XPS studies indicated that the formation or deposition of a few monolayers of hydrophobic carbonaceous species on surface can affect CHF values. The trends in CHF data are discussed in terms of evolution of the surface characteristics of the ATF materials.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Quantifying the Effect of Pore‐Size Dependent Wettability on Relative Permeabilities Using Lattice Boltzmann Simulation

Relative permeability is a crucial two-phase property in porous media that can be significantly impacted by wettability conditions. While traditional research has predominantly examined homogeneous wettability, this work explores the less studied pore-size dependent (PSD) wettability, featured by a pore-size dependent wettability distribution. Leveraging high-fidelity Lattice Boltzmann simulations on CT-scanned porous samples, we demonstrate how PSD wettability would impact relative permeability at the pore scale. Our findings reveal that the deviation of relative permeability from the homogeneous wettabilitity induced by PSD wettability can be 5%–20%. The deviation of relative permeability curves increases as the spanning range of the contact angle increases. We also find that this impact is less pronounced as the capillary number increases. By adopting a pore-size-dependent contact angle relationship, our approach provides a more accurate and nuanced understanding of how PSD wettability would impact two-phase flow. These findings discovered at the pore scale may also provide valuable insights on relative permeability at the core to reservoir scales.

25 ENERGY STORAGE↗
DOE OSTI2020

Significance of a Solid Electrolyte Interphase on Separation of Anode and Cathode Materials from Spent Li-Ion Batteries by Froth Flotation

The separation of electrode active materials from spent Li-ion batteries (LIBs) by froth flotation is challenging due to the changes in surface properties of electrode active materials from cycling as well as the presence of organic binders. In this work, the froth flotation separation of aged anode and cathode composite materials from spent LIBs was systematically investigated after the materials were heat treated. The results show that aged anode and cathode materials from spent LIBs can be well separated from each other after a heating process in air at 400 degrees C and at which some of the PVDF binder remains intact. The underlying mechanism was investigated by X-ray photoelectron spectroscopy (XPS), contact angle measurements, and scanning transmission electron microscopy (STEM) coupled with energy-dispersive X-ray spectroscopy (EDX). The results from the XPS and contact angle measurements show that there is a hydrophilic and oxygen-rich layer on the surface of aged anode materials. This hydrophilic surface, associated with the solid electrolyte interface (SEI) layer, impacts the froth flotation process significantly. The results also show that both the SEI layers and PVDF binder residues on the surface are removed at 400 degrees C for an hour, restoring the hydrophobicity of the anode materials, which, in turn, benefits the separation of anode and cathode materials. The STEM/EDX elemental analysis data confirms that there are 20 nm-thick oxygen-rich SEI layers on the surfaces, which can be removed after a heating process. The present result illustrates the significance of the SEI layers in flotation separation of electrode materials and sheds new lights into the future development of the recycling processes for the separation of anode and cathode composite materials from spent Li-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Molecular Dynamics Investigation of Oil Wetting on Synthetic Polymer Substrates

Understanding the interaction of polymer surfaces with nonpolar, low surface tension liquids, or whether a substrate is oleophobic versus oleophilic, is critical for applications ranging from antifingerprint coatings to oil–water separation membranes and oil spill remediation. Despite its technological importance, the molecular mechanisms underpinning polymer–oil wetting are not well characterized. Here, we employ molecular dynamics simulations to investigate the behavior of n-hexadecane in contact with chemically distinct polymer surfaces, spanning eight constitutional unit chemistries as well as amorphous and crystalline morphologies. This permits a critical examination of both thermodynamic and dynamic descriptors of oleophobicity, including oil contact angle, dewetting free energy, interfacial diffusivity, and a proposed “ghost probe energy,” which does not require explicit simulation of oil–polymer interactions. We find that the oil contact angle does not reliably distinguish oleophobic behavior across polymer chemistries, whereas other metrics provide clearer and more consistent differentiation. Analysis of the results reveals that polymer–oil wetting behavior is primarily governed by interfacial van der Waals interactions and modulated by surface flexibility and morphology. Collectively, this work establishes a computational framework for characterizing oil wetting and provides additional insight into what molecular-level factors dictate trends in oleophobicity.

lipids↗
DOE OSTI2022

Toward controlling wetting hysteresis with nanostructured surfaces derived from block copolymer self-assembly

The synthesis of nanostructured surfaces via block copolymer (BCP) self-assembly enables a precise control of the surface feature shape within a range of dimensions of the order of tens of nanometers. Herein, this work studies how to exploit this ability to control the wetting hysteresis and liquid adhesion forces as the substrate undergoes chemical aging and changes in its intrinsic wettability. Via BCP self-assembly we fabricate nanostructured surfaces on silicon substrates with a hexagonal array of regular conical pillars having a fixed period (52 nm) and two different heights (60 and 200 nm), which results in substantially different lateral and top surface areas of the nanostructure. The wetting hysteresis of the fabricated surfaces is characterized using force–displacement measurements under quasistaic conditions and over sufficiently long periods of time for which the substrate chemistry and surface energy, characterized by the Young contact angle, varies significantly. The experimental results and theoretical analysis indicate that controlling the lateral and top area of the nanostructure not only controls the degree of wetting hysteresis but can also make the advancing and receding contact angles less susceptible to chemical aging. These results can help rationalize the design of nanostructured surfaces for different applications such as self-cleaning, enhanced heat transfer, and drag reduction in micro/nanofluidic devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Influence of Surface Treatment on the Interfacial and Mechanical Performance of Metal-Insert Overmolded Composites

Structural composites with metal inserts are gaining increasing interest enabling light weight design for energy efficiency, provide insulation, corrosion protection without compromising mechanical integrity. Such over molded metal-polymer composites show strong potential in many automotive and aerospace component parts, e.g. car bumper, chassis, door, brackets, fasteners, etc. Despite several advantages, metal-polymer dissimilar interface remains a weak spot in structural design, requiring further investigation to improve interfacial interlocking. The current work focuses on enhancing the metal-polymer adhesion between stainless steel inserts and polymer matrices (e.g. acrylonitrile butadiene styrene resin (ABS), and polyamide 66 (PA66) through surface treatment via chemical etching and mechanical roughening. In the chemical etching process, metal substrates were treated with aqua regia solution for different time intervals to evaluate surface roughness measured by water contact angle and morphology analysis. For mechanical roughening approach, metal inserts were subjected to blasting for surface abrasion. Treated samples were also functionalized with aminosilane coupling agent which showed successful grafting on the surface measured by water contact angle. Metal inserts with micro level surface roughness through etching exhibited significant 21% improvement in adhesion strength compared to untreated inserts; however, the effect of silane treatment on the interfacial strength was found to be highly matrix dependent.

Saha, Subhabrata [ORNL] (ORCID:000000033966064X)↗
DOE OSTI2022

Design optimization of gap distance for the capillary limitation of a heat pipe with annular-type wick structure

In this study, an experimental investigation was conducted on the rising height and contact angle of fluid in an annular wick-type heat pipe. The annular wick-type heat pipe was characterized by a small gap between the wick structure and tube wall, which compensated for the pressure drop along the porous media and created additional capillary force. To describe and model the advantage of this gap, the rising of a wetting liquid in the gap between a vertical solid plate and a mesh (with a small angle between them) was experimentally measured and analyzed. An additional experiment was performed to investigate the effect of curvature on the capillary rise using tubes and meshes of varying radii. Resultantly, we confirmed that the linear combination of the contact angles of the solid plate and mesh could be applied to calculate the rising height from the Laplace–Young equation. Furthermore, the effect of curvature on the rising height of the liquid was negligible. These results were extended to the investigation of finding the optimal gap distance for the annular wick-type heat pipe by referring to previous studies. We observed that a gap distance of 1.27 mm provided the largest permeability (K) over the effective pore radius (r eff ) value for a heat pipe with ethanol, which in turn resulted in the highest capillary limitation. For a sodium heat pipe, a gap distance of 0.84 mm resulted in the highest capillary limitation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Aging of Limestones and Silane–Siloxane-Based Protective Hydrophobics: The Impact of Heating–Cooling and Freeze–Thaw Cycles

Stones are traditionally used in construction and architectural applications as building elements due to their aesthetic and technical/structural performance. Like other environmental factors (rain, humidity, moisture, salt presence, biological activity, etc.), heating–cooling and freeze–thaw cycles significantly threaten the longevity of stone materials. Hence, considering the socio-economic and cultural value of stones, preventive actions such as hydrophobic coatings are applied to prevent or mitigate damage. The scope of this study is the performance assessment of limestones with different characteristics and the efficiency of various commercial silane/siloxane-based hydrophobic coatings when exposed to thermal variation and freeze–thaw. For that purpose, the standards EN 14066:2013 (determination of resistance to aging by thermal shock) and EN 12371:2010 (determination of frost resistance) were followed. Open porosity and static contact angles were estimated to assess the stone durability and water protection capabilities of the hydrophobics. Additionally, sound speed propagation velocity, quality of building material index, elastic modulus and flexural strength were measured to evaluate the variation of mechanical properties. Static contact angle revealed that the coatings maintained an efficient level of hydrophobicity even after thermal-shock and freeze–thaw weathering tests. The study also revealed a critical interaction between freeze–thaw cycles, hydrophobic coatings and structural integrity of the stones, mostly on more porous ones. When they are subjected to harsh environmental conditions, untreated porous limestones keep structural cohesion, allowing for the natural absorption and release of water during freezing and thawing. On the contrary, when limestones are treated, the hydrophobic coatings can moderately obstruct the water release due to the partial saturation of the porous framework by the products. It also probably resulted from the different mechanical behavior between the inner matrix and layer of stone coated, resulting in a premature breakout and mechanical damage of the stone.

Lisci, Carla (ORCID:000000032179130X)↗
DOE OSTI2024

Corrosion protection of mild steel by superhydrophobic magnetite coating

Corrosion-resistant hydrophobic magnetite coatings on mild steel surfaces were developed by immersion method. The effect of steel surface roughness (R a ) on its hydrophobicity was systematically studied using contact angle measurement (CAM), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The corrosion resistance of hydrophobic magnetite coatings was evaluated using a potentiodynamic polarization test. The durability of the coatings was assessed in air, tap water, and 3.5 wt% NaCl environments. Hydrophobic magnetite coating with a water contact angle of 146-152° showed excellent resistance to corrosion, longevity in atmospheric air, and significant self-cleaning properties. The primary focus of this study was to develop a quick and simple immersion technique to create hydrophobic surfaces on mild steel. Finally, results suggest that surface roughness plays a significant role in surface hydrophobicity, and enhancing the hydrophobicity of mild steel improves its corrosion resistance.

36 MATERIALS SCIENCE↗