SEARCH · Search NASA

Results for “coordinated attacks”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1985

An assessment of some vorticity field-leading edge interactions

A review is undertaken of some recent advances in the following areas: the encounter of distributed and concentrated vorticity at a single frequency with a leading-edge, the interaction of multiple concentrations of vorticity with an edge, the distortion due to finite scale and angle of attack of the leading-edge, and the penetration of the leading-edge interaction into the near-wake region. Time-sequence flow visualization and phase-coordinated pressure measurements provide physical insight into the mechanisms of flow distortion and loading. Promising paths for future research are suggested on the basis of recent progress.

Rockwell, D.↗

NASA NTRS1979

Upper-surface modifications for C sub l max improvement of selected NASA 6-series airfoils

The thickness of the upper surface of 64 airfoils was increased from the leading edge to the position of maximum thickness. The modifications were generated using a numerical optimization routine coupled with an aerodynamic analysis code. The type of modification presented can be used for aircraft design or for the retrofit of current aircraft to improve the stall characteristics and climb performance. The coordinates of the modified airfoils are presented with plots of the forward 45% of the profiles and pressure distributions for both the modified and unmodified sections at an angle of attack of 14 degrees.

Szelazek, C. A.↗

NASA NTRS1991

Control concept for maneuvering in hypersonic flight

This research investigates an approach to provide precise, coordinated maneuver control during excursions from a hypersonic cruise flight path while observing the necessary flight condition constraints. The approach achieves specified guidance commands by resolving altitude and cross-range errors into a load factor and bank angle command through a coordinate transformation which acts as an interface between outer loop guidance controls and inner loop flight controls. This interface, referred to as a 'resolver', applies constraints on angle-of-attack and dynamic pressure perturbations while prioritizing altitude regulation over crossrange. An unpiloted test simulation, in which the resolver was used to drive inner-loop flight controls, produced time histories of responses to guidance commands at Mach numbers of 6, 10, 15, and 20. It is shown that angle-of-attack and throttle perturbation constraints, combined with high-speed flight effects and the desire to maintain constant dynamic pressure, significantly impact the maneuver envelope for a hypersonic vehicle. Turn rate, climb rate, and descent rate limits are expressed in terms of these constraints.

Raney, David L.↗

NASA NTRS1984

Numerical simulation of the viscous flow fields over three-dimensional complicated geometries

A 'thin-layer' Navier-Stokes code capable of predicting steady state viscous flows is applied to complicated three-dimensional flow fields. The code is written in a generalized coordinate system, and a recently developed grid generation procedure is used for the flow-field discretization. Application is made to the vortical flow over a delta wing at high angle of attack, and the computed results are compared with experimental results. The results indicate that the present method can capture the physical phenomenon well. It is observed that a leading-edge separation vortex is formed over the wing, as is a secondary separation vortex near the leading edge. The flow field behind the trailing edge is also well described. Application is also made to the transonic flow over the Shuttle configuration. The result appears to be reasonable even though no experimental data are available for comparison. These results indicate that the present approach is capable of computing complicated three-dimensional flow fields.

Fujii, K.↗

NASA NTRS1979

An efficient user-oriented method for calculating compressible flow about three-dimensional inlets

This method uses a so-called panel method to calculate incompressible flow about arbitrary three-dimensional inlets with or without centerbodies for four fundamental flow conditions: unit onset flows parallel to each of the coordinate axes plus static operation. The computing time is scarcely longer than for a single solution. A linear superposition of these solutions quite rigorously gives incompressible flow about the inlet for any angle of attack, angle of yaw, and mass flow rate. Compressibility is accounted for by applying a well-proven correction to the incompressible flow. Since the computing times for the combination and the compressibility correction are small, flows at a large number of inlet operating conditions are obtained very cheaply. A number of graphical output features are provided to aid the user, including streamline tracing and automatic generation of curves of constant pressure, Mach number, and flow inclination at selected inlet cross sections. This paper describes the method in some detail and presents calculated results.

Hess, J. L.↗

NASA NTRS1979

An efficient user-oriented method for calculating compressible flow in an about three-dimensional inlets

A panel method is used to calculate incompressible flow about arbitrary three-dimensional inlets with or without centerbodies for four fundamental flow conditions: unit onset flows parallel to each of the coordinate axes plus static operation. The computing time is scarcely longer than for a single solution. A linear superposition of these solutions quite rigorously gives incompressible flow about the inlet for any angle of attack, angle of yaw, and mass flow rate. Compressibility is accounted for by applying a well-proven correction to the incompressible flow. Since the computing times for the combination and the compressibility correction are small, flows at a large number of inlet operating conditions are obtained rather cheaply. Geometric input is aided by an automatic generating program. A number of graphical output features are provided to aid the user, including surface streamline tracing and automatic generation of curves of curves of constant pressure, Mach number, and flow inclination at selected inlet cross sections. The inlet method and use of the program are described. Illustrative results are presented.

Hess, J. L.↗

NASA NTRS1985

Preliminary design study of a lateral-directional control system using thrust vectoring

A preliminary design of a lateral-directional control system for a fighter airplane capable of controlled operation at extreme angles of attack is developed. The subject airplane is representative of a modern twin-engine high-performance jet fighter, is equipped with ailerons, rudder, and independent horizontal-tail surfaces. Idealized bidirectional thrust-vectoring engine nozzles are appended to the mathematic model of the airplane to provide additional control moments. Optimal schedules for lateral and directional pseudo control variables are calculated. Use of pseudo controls results in coordinated operation of the aerodynamic and thrust-vectoring controls with minimum coupling between the lateral and directional airplane dynamics. Linear quadratic regulator designs are used to specify a preliminary flight control system to improve the stability and response characteristics of the airplane. Simulated responses to step pilot control inputs are stable and well behaved. For lateral stick deflections, peak stability axis roll rates are between 1.25 and 1.60 rad/sec over an angle-of-attack range of 10 deg to 70 deg. For rudder pedal deflections, the roll rates accompanying the sideslip responses can be arrested by small lateral stick motions.

Lallman, F. J.↗

NASA NTRS1983

Numerical simulation of the leading-edge separation vortex for a wing and strake-wing configuration

In the present investigation, the 'thin layer' Navier-Stokes equations are used to compute the flow about a delta wing and a strake-delta wing configuration. Both configurations possess blunt noses and rounded leading edges. The computational grid about these configurations is generated using a newly developed three-dimensional grid-generation code which solves a set of Poisson equations with spherical coordinate variables using an alternating direction implicit (ADI) scheme. Computational results are obtained for an isolated wing with 60 deg sweep and a strake-wing configuration with 80-60 deg sweep. Computations for angles of attack in the range from 6 to 30 deg are presented. Attention is given to the effect of the angle of attack, the Mach number, and the Reynolds number. Theoretical results are compared with experimental data.

Fujii, K.↗

NASA NTRS1989

Worldnet

The expanding use of powerful workstations coupled to ubiquitous networks is transforming scientific and engineering research and the the ways organizations around the world do business. By the year 2000, few enterprises will be able to succeed without mastery of this technology, which will be embodied in an information infrastructure based on a worldwide network. A recurring theme in all the discussions of what might be possible within the emerging Worldnet is people and machines working together in new ways across distance and time. A review is presented of the basic concepts on which the architecture of Worldnet must be built: coordination of action, authentication, privacy, and naming. Worldnet must provide additional functions to support the ongoing processes of suppliers and consumers: help services, aids for designing and producing subsystems, spinning off new machines, and resistance to attack. This discussion begins to reveal the constituent elements of a theory for Worldnet, a theory focused on what people will do with computers rather than on what computers do.

Denning, Peter J.↗

NASA NTRSDate not supplied

Blade Displacement Measurements of a Rotor in Forward Flight in the Langley 14- by 22-Ft Wind Tunnel

Stereo photogrammetry was used to measure the elastic bending and twist of a three-bladed rotor in forward flight in the NASA Langley 14-by 22-Ft Subsonic Wind Tunnel. The rotor was imaged from below by two cameras mounted at windows of a large turntable in the floor of the test section. At each test condition, the turntable and cameras were rotated and the cameras were triggered to allow measurements over a range of blade azimuth angles. Retro-reflective targets were applied along the leading and trailing edges of the lower surface of each blade. Image blur due to blade motion was minimized by illuminating the targets with high-intensity LED flash lamps mounted next to each camera. The cameras were re-calibrated at each angular position of the turntable using the positions in each image of retro-reflective targets on the ceiling of the test section whose spatial coordinates had been very accurately measured. The blade displacement measurements yielded elastic bending and twist along each blade as functions of blade azimuth, thrust coefficient, and advance ratio, all at a constant rotor angle-of-attack. In addition, the measurements produced estimates of the rigid-body blade pitch, flap, and lag angles.

rotor blade displacement↗

NASA NTRS1978

A split-recoupled-semidirect computational technique applied to transonic flow over lifting airfoils

A new version of the semidirect iterative method eliminates significant restrictions of previous versions of the method. A semidirect method solves finite-difference equations by a rapid globally implicit iterative process driven by a fast direct elliptic solver. The new approach can treat complex systems of equations in an efficient 'correction form', and allows the use of general, nonorthogonal, boundary-fitted coordinate transformations. These features are expected to lead to significant practical applications with conservation-equation systems in either two or three dimensions. The present application to the full potential equations for steady transonic flow over an airfoil at angle of attack illustrates the utility of the technique.

Martin, E. D.↗

NASA NTRS1990

Control research in the NASA high-alpha technology program

NASA is conducting a focused technology program, known as the High-Angle-of-Attack Technology Program, to accelerate the development of flight-validated technology applicable to the design of fighters with superior stall and post-stall characteristics and agility. A carefully integrated effort is underway combining wind tunnel testing, analytical predictions, piloted simulation, and full-scale flight research. A modified F-18 aircraft has been extensively instrumented for use as the NASA High-Angle-of-Attack Research Vehicle used for flight verification of new methods and concepts. This program stresses the importance of providing improved aircraft control capabilities both by powered control (such as thrust-vectoring) and by innovative aerodynamic control concepts. The program is accomplishing extensive coordinated ground and flight testing to assess and improve available experimental and analytical methods and to develop new concepts for enhanced aerodynamics and for effective control, guidance, and cockpit displays essential for effective pilot utilization of the increased agility provided.

Gilbert, William P.↗

NASA NTRS2014

Toward Improved CFD Predictions of Slender Airframe Aerodynamics Using the F-16XL Aircraft (CAWAPI-2)

A coordinated project has been underway to improve CFD predictions of slender airframe aerodynamics. The work is focused on two flow conditions and leverages a unique flight data set obtained with an F-16XL aircraft. These conditions, a low-speed high angleof- attack case and a transonic low angle-of-attack case, were selected from a prior prediction campaign wherein the CFD failed to provide acceptable results. In this paper the background, objectives and approach to the current project are presented. The work embodies predictions from multiple numerical formulations that are contributed from multiple organizations, and the context of this campaign to other multi-code, multiorganizational efforts is included. The relevance of this body of work toward future supersonic commercial transport concepts is also briefly addressed.

Luckring, James M.↗

NASA NTRS1984

Incorporation of wind shear terms into the governing equations of aircraft motion

Conventional analyses of aircraft motion in the atmosphere have neglected wind speed variability on the scales associated with many atmospheric phenomena such as thunderstorms, low-level jets, etc. These phemonena produce wind shears that have been determined as the probable cause in many recent commercial airline accidents. This paper derives the six degrees equations of motion or an aircraft incorporating the variable wind terms. The equations are presented in several coordinate systems (i.e., body coordinates, inertial coordinates, etc.). The wind shear terms, including the temporal and spatial gradients of the wind, appear differently in the various coordinate system. These terms are discussed. Also, the influence of wind shear on inputs to computing the aerodynamic coefficients such as the effects of wind velocity vector rotation on relative angular rates of rotation and on the time rate of change of angles of attack and side slip are addressed.

Frost, W.↗

NASA NTRS1996

Twin Tail/Delta Wing Configuration Buffet Due to Unsteady Vortex Breakdown Flow

The buffet response of the twin-tail configuration of the F/A-18 aircraft; a multidisciplinary problem, is investigated using three sets of equations on a multi-block grid structure. The first set is the unsteady, compressible, full Navier-Stokes equations. The second set is the coupled aeroelastic equations for bending and torsional twin-tail responses. The third set is the grid-displacement equations which are used to update the grid coordinates due to the tail deflections. The computational model consists of a 76 deg-swept back, sharp edged delta wing of aspect ratio of one and a swept-back F/A-18 twin-tails. The configuration is pitched at 32 deg angle of attack and the freestream Mach number and Reynolds number are 0.2 and 0.75 x 10(exp 6) respectively. The problem is solved for the initial flow conditions with the twin tail kept rigid. Next, the aeroelastic equations of the tails are turned on along with the grid-displacement equations to solve for the uncoupled bending and torsional tails response due to the unsteady loads produced by the vortex breakdown flow of the vortex cores of the delta wing. Two lateral locations of the twin tail are investigated. These locations are called the midspan and inboard locations.

Kandil, Osama A.↗

NASA NTRS1973

On electromagnetic field problems in inhomogeneous media

Analysis of electromagnetic fields in inhomogeneous media is of practical interest in general scattering and propagation problems and in the study of lenses. For certain types of inhomogeneities, the fields may be represented in terms of two scalars. In a general orthogonal coordinate system, these potentials satisfy second order differential equations. Exact solutions of these equations are known only for a few particular cases and in general, an approximate or numerical technique must be employed. The present work reviews and generalizes some of the main methods of attack of the problem. The results are presented in a form appropriate for numerical computation.

Mohsen, A.↗

NASA NTRS1986

A direct-inverse method for the prediction of transonic and separated flows about airfoils at high angles of attack

A direct-inverse technique and computer program called TAMSEP that can be used for the analysis of the flow about airfoils at subsonic and low transonic freestream velocities is presented. The method is based upon a direct-inverse nonconservative full potential inviscid method, a Thwaites laminar boundary layer technique, and the Barnwell turbulent momentum integral scheme; and it is formulated using Cartesian coordinates. Since the method utilizes inverse boundary conditions in regions of separated flow, it is suitable for predicting the flowfield about airfoils having trailing edge separated flow under high lift conditions. Comparisons with experimental data indicate that the method should be a useful tool for applied aerodynamic analyses.

Carlson, L. A.↗

NASA NTRS1996

Aerostructural Vortical Flow Interactions with Applications to F/A-18 and F-117 Tail Buffet

The buffet response of the flexible twin-tail configuration of the F/A-18 and a generic F-111 aircraft are computationally simulated and experimentally validated. The problem is a multidisciplinary one which requires the sequential solution of three sets of equations on a multi-block grid structure. The first set is the unsteady, compressible, full Navier-Stokes equations. The second set is the aeroelastic equations for bending and torsional twin-tail responses. The third set is the grid-displacement equations which are used to update the grid coordinates due to the tail deflections. The computational models consist of a 76 deg. swept back, sharp edged delta wing of aspect ratio of one and a swept-back F/A-18 or F-117 twin-tail. The configuration is pitched at 30 deg. angle-of-attack. The problem is solved for the initial flow conditions with the twin tails kept rigid. Next, the aeroelastic equations of the tails are turned on along with the grid-displacement equations to solve for the bending and torsional tails responses due to the unsteady loads produced by the vortex breakdown flow of the leading-edge vortex cores of the delta wing. Several spanwise locations of the twin tails are investigated. The computational results are validated using several existing experimental data.

Kandil, Osama A.↗