Search NASA⌕ Search

SEARCH · Search NASA

Results for “cracking”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Crack Propagation Modeling of a High-Speed Outer Rotor Motor

This study aims to investigate the propagation of initial cracks in electric motors and their rate of spread through the rotor structure under various operating conditions. Traction motors are subjected to high centrifugal load owing to their speed and rapid acceleration and deceleration. In the manufacturing process, some initial imperfections or cracks in the rotor components are likely to occur. Under the influence of loading, these cracks will grow, and factors such as loading frequency, material strength, and location of material voids will affect this threshold speed. In the current study, a fracture mechanics–based approach has been used to investigate the crack growth rate for a 100 kW outer rotor motor with a rated speed of 6,000 rpm and a peak speed of 20,000 rpm for an integrated drive application.

Barua, Himel↗
DOE OSTI2024

Modelling of cracking during beam oscillation laser welding of a creep-resistant nickel alloy

During high power laser welding of Inconel 740H, horizontal solidification cracks form at locations between approximately 70–80% of the weld depth. With the integration of circular beam oscillation, the laser energy density distribution and underlying thermo-mechanical conditions were altered. By coupling three-dimensional heat transfer, fluid flow, and stress modelling tools, the role that circular beam oscillation plays in the formation of the strain rates and stresses driving this cracking phenomenon was identified. While the addition of a circular oscillation pattern appeared to lower the stress levels along the solidification front, it did not eliminate the appearance of horizontal cracking. Only when the beam amplitudes reached 1.6 mm did solidification cracking disappear, but the weld depths were also significantly reduced.

Gao, Mingze↗
DOE OSTI2025

Fundamental Study of Fatigue Crack Initiation at Grain and Twin Boundaries in Austentic Stainless Steel (Final Technical Report)

The overarching goal of this project was to understand the dislocation-based mechanisms driving fatigue crack initiation at grain and twin boundaries. The hypothesis of the work is that dislocation structures equivalent to persistent slip bands (PSBs) form in the boundaries, leading to local stress concentrations and fatigue crack initiation. The sub-goals associated with this work include: • Understanding the evolution of the dynamic stress state and dislocation density surrounding PSB/grain boundary interactions. This will require the development of new techniques that couple high resolution electron backscatter diffraction (HREBSD) with in situ scanning electron microscopy (SEM) deformation. • Uncover the mechanisms by which dislocations are accommodated in grain and twin boundaries during fatigue. The proposed approach here is to conduct in situ transmission electron microscopy (TEM) deformation experiments on fatigued samples. • Establish correlations between microstructure, deformation accommodation, and crack initiation across time and length scales. This work primarily focuses on understanding fatigue crack initiation in austenitic stainless steels, though promising work by an undergraduate researcher extended the work to high purity Al.

42 ENGINEERING↗
DOE OSTI2025

Stochastic 3D reconstruction of cracked polycrystalline NMC particles using 2D SEM data

Li-ion battery performance is strongly influenced by the 3D microstructure of its cathode particles. Cracks within these particles develop during calendaring and cycling, reducing connectivity but increasing reactive surface, making their impact on battery performance complex. Understanding these contradictory effects requires a quantitative link between particle morphology and battery performance. However, informative 3D imaging techniques are time-consuming, costly and rarely available, such that analyses often have to rely on 2D image data. This paper presents a novel stereological approach for generating virtual 3D cathode particles exhibiting crack networks that are statistically equivalent to those observed in 2D sections of experimentally measured particles. Consequently, 2D image data suffices for deriving a full 3D characterization of cracked cathodes particles. Such virtually generated 3D particles could serve as geometry input for spatially resolved electro-chemo-mechanical simulations to enhance our understanding of structure-property relationships of cathodes in Li-ion batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Low temperature polyolefin deconstruction via tandem cracking-hydrogenation

The use of aluminum chloride in dichloromethane to crack polyolefin chains in tandem with alkylation of the resulting products has been previously reported as an efficient polyolefin recycling route. Building off this work, we report that a tandem cracking-hydrogenation system also efficiently converts polyolefins into gasoline-range light alkanes at mild temperatures without needing a hydrocarbon co-reactant. This Lewis acid and hydrogenation bifunctional system uses anhydrous aluminum chloride as the acid catalyst and Pd/C as a hydrogenation catalyst to achieve nearly 80 % conversion of low-density polyethylene (LDPE) at 70 °C in three hours, with 90+% selectivity towards gasoline-range (C 4 -C 12 ) branched alkanes. By combining the endothermic cracking reaction with the exothermic hydrogenation reaction, the thermodynamic limitations to low-temperature polyolefin deconstruction can be overcome. In using hydrogenation instead of alkylation, the system’s carbon efficiency is greatly improved, the cost of the reactants is reduced and the overall mass of both reactants and products reduced as well.

Alkylation↗
DOE OSTI2024

Consistency of fatigue crack growth behavior of pipeline and low-alloy pressure vessel steels in gaseous hydrogen

Here, this study investigates the fatigue crack growth rate (FCGR) behavior of pipeline and low-alloy pressure vessel steels in high-pressure gaseous hydrogen. Despite a broad range of yield strengths and microstructures ranging from ferrite/pearlite, acicular ferrite, bainite, and martensite, the FCGR in gaseous hydrogen remained consistent (falling within a factor of 2–3). Steels with higher fractions of pearlite, typical of older vintage pipeline steels, exhibited modestly lower crack growth rates in gaseous hydrogen compared to steels with lower fractions of pearlite. Crack growth rates in these materials exhibit a systematic dependence on stress ratio and partial pressure of hydrogen, as captured in the recently published fatigue design curves in ASME B31 code case 220 for pipeline steels and ASME BPVC code case 2938 for pressure-vessel steels.

08 HYDROGEN↗
DOE OSTI2025

Fabrication of surrogate oxide spent fuel with various cracking patterns and design of an axial gas transport apparatus

In this article, understanding gas transport behavior in nuclear fuel rods is important for the design, performance, and safety of nuclear fuels. Surrogate materials help enable efficient research by reducing both the costs and the amount of time required. A parametric study using Darcy’s law is completed that demonstrates the feasibility of observing pressure decay over short 13-to-15-cm specimens to enable full characterization of the fabricated specimens using x-ray computed tomography. This paper demonstrates that thermally shocked and mechanically compressed alumina pellets produce surrogate samples whose various cracking patterns are representative of the severity of cracking observed as a function of burnup in irradiated nuclear fuels. Furthermore, image analyses of the cracking patterns—in conjunction with gas transport testing using surrogate samples—affords a valuable accelerated basis for developing gas transport simulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Materials Degradation in Extreme Environments: Novel In-situ Measurements of Cracking in Molten Salt

The safety and reliability of next-gen reactors, i.e. molten salt reactors (MSR), depends on materials performance and longevity in extreme environments, yet no in-situ, validated measurement techniques for environmentally assisted cracking (EAC), one potential degradation mechanism, exist for these conditions. This project combined the use of in-situ direct current potential drop (DCPD) crack growth rate determination applied to a horizontal load frame with high temperature fittings and novel sample geometries to enable evaluation in MSR environments and develop a full in-situ SCC measurement capability for extreme environments (high conductivity and elevated T), necessary to predict materials reliability. A successful demonstration of DCPD measurement in molten NaNO 3 /KNO 3 salts at 340 o C was accomplished and validated through post-test fractography imaging. This is the first ever public example, to the authors knowledge, of an in-situ crack growth rate measurement in a molten salt environment.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Complex Fluid‐Driven Fractures Caused by Crack‐Parallel Stress

Abstract Managing fluid‐driven fracture networks is crucial for subsurface resource utilization, yet the current understanding of the key controlling factors remains insufficient. While geologic discontinuities have been shown to significantly influence fracture network complexity, this study identifies another major contributor. We conducted a new set of experiments using a transparent true triaxial cell, which enabled video recording of the temporal evolution of fluid‐driven fracture paths. Using pseudo‐2D samples without macroscale structural discontinuities, we observed multiple occurrences of hydraulic fracture curving and branching under anisotropic boundary stresses. We proposed a theoretical model demonstrating that the stress parallel to the crack line in the solid matrix near the crack tip (i.e., the T ‐stress) accounts for the observed fracture curving behavior. This finding suggests that T ‐stress is an additional mechanism contributing to the complexity of fluid‐driven fracture networks in the subsurface, besides the geologic discontinuities.

58 GEOSCIENCES↗
DOE OSTI2026

Reducing the Cost of Fatigue Crack Growth Testing for Storage Vessel Steels in Hydrogen Gas

Hydrogen storage pressure vessels are designed against fatigue crack growth, and the ASME Boiler and Pressure Vessel Code requires the fatigue crack growth rate (da/dN) vs. stress-intensity factor range (ΔK) relationship of the construction steel to be measured directly in hydrogen gas. These measurements are notoriously slow and expensive: the cyclic loading frequencies prescribed by standards (often 0.1 Hz) are two or more orders of magnitude below those for conventional fatigue testing, individual tests run for days to weeks, and the high-pressure test-chamber set-up imposes a significant per-specimen labor cost. Due to these time and cost constraints, near-threshold data—the regime most valuable for extending design fatigue life—are rarely generated for ferritic storage vessel steels in hydrogen gas.

08 HYDROGEN↗
DOE OSTI2026

Strain age cracking in a simulated heat affected zone of Inconel 740H laser-powder bed fusion components

Inconel® 740H components produced via laser-powder-bed fusion (L-PBF) additive manufacturing are ideal for supercritical CO2 primary heat exchangers. Arc welding is often needed, and subsequent post-weld heat treatment aging at 790–840 °C is required to improve strength via gamma prime (γ’) precipitation; however, strain age cracking (SAC) can occur in the heat affected zone (HAZ) during this process. This study uses stress relaxation testing at 800 °C on simulated HAZ specimens from vertically and horizontally built L-PBF IN740H to assess SAC susceptibility across heating rates of 40–3480 °C/h and weld-induced strains of 3–10 %. Vertical builds require greater mechanical energy input and exhibit longer times to fracture than horizontal builds, and time to fracture occurs sooner at slower heating rates. Creep voids were observed in γ’-denuded regions along grain boundaries, and cracking propagated along migrated grain boundaries and at interfaces between elongated secondary phases (γ’ or carbides) and the γ-matrix.

14 SOLAR ENERGY↗
DOE OSTI2026

Multiscale fatigue crack initiation in hierarchical additively manufactured alloys

Bioinspired hierarchical microstructures offer a route toward engineered fatigue resistance in additively manufactured alloys. However, it remains unclear how discrete structural constituents independently govern damage accumulation, particularly during the critical fatigue initiation regime where short cracks strongly interact with local microstructure. Here, we investigate multiscale fatigue initiation in a dual-phase, nanolamellar AlCoCrFeNi 2.1 high-entropy alloy. By comparing microscale specimens that isolate the nanolamellar structure against macroscale specimens containing the full melt-pool architecture, we identify size-dependent fatigue initiation mechanisms. We find that failure is dictated by nanolamellar interfaces at the microscale, whereas mesoscale melt pool boundaries serve to initiate fatigue at the macroscale. This mechanistic shift is accompanied by a transition from macroscale quasi-brittle failure to microscale plasticity-driven crack extension. Our results provide a physical framework for understanding how structural hierarchy governs the transition from discrete microstructural deformation to continuum fatigue fracture behavior, informing the design of damage-tolerant, additively manufactured alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

FY24 Progress Report: Disposition of Cracks & Features Observed in the Inner Can Closure Weld Region (ICCWR) of the 3013 Package

The long-term integrity of the 3013 containers is of interest for the safe storage of Pu materials. Although the 3013 standard embodies multiple barrier concept, the integrity of the inner container is considered to be crucial since it protects the Safety Class outer container from its contents. The container is designed to withstand high pressures that could result from the complete radiolysis of the maximum water content permissible by the 3013 standard. Shelf-life studies and destructive examination have not found high gas pressures but have found that corrosive gases are generated. Pitting and stress corrosion cracking (SCC) are considered to be critical corrosion modes for the performance of the inner container and have been observed during destructive examinations. Considerable research has been conducted on the possibility of aqueous electrolytes condensing on the inner container that can promote SCC. These studies indicate the uncertainties surrounding the formation of corrosive environments and the corrosion behavior of container materials. In this initial report, a Bayesian network (BN) model is described that can consider the uncertainties and the causal connections between various factors influencing the corrosion modes of the inner container. The BN model is preliminary and provides an initial framework to identify the necessary information. The report also provides initial experimental results on the electrochemical behavior of stainless steels in anticipated condensed environments from gas phase migration of acidic gases. The experimental results are consistent with the corrosion model. Recommendation for further work on the BN model include assembling an expert group to provide input to the BN structure and quantification of the conditional probability matrix, experimental studies to characterize the microstructure of the container, electrochemical studies to identify critical potentials for localized corrosion and SCC, and crack growth rate studies

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Surrogate Model Integration with MOOSE XFEM for Creep Crack Growth

Ferritic-martensitic steels are key structural materials for advanced reactors but experience time-dependent deformation and damage under prolonged high temperature and irradiation, leading to creep-driven crack initiation and growth. High-fidelity models—crystal plasticity with irradiation mechanisms, phase-field for microstructural evolution, and continuum-damage viscoplasticity—capture the underlying physics but are too computationally intensive for broad design-space exploration and uncertainty quantification. This milestone advances a scalable alternative by integrating a microstructure-sensitive surrogate creep model into the Multiphysics Object-Oriented Simulation Environment (MOOSE) finite element framework and extending it to fracture via the extended finite element method (XFEM). The surrogate model, developed with collaborators at Sandia and Los Alamos National Laboratories, maps relevant microstructural descriptors to the viscoplastic response of HT9. We embed this surrogate within a coupled deformation-damage workflow in MOOSE/XFEM to simulate creep-driven crack initiation and propagation. Implementation enhancements include updates to the material interface, a plastic correction phase involving microstructure evolution, and fracture criteria to ensure numerical robustness and compatibility with the surrogate structure. Demonstrations on canonical creep benchmarks spanning uniaxial and multiaxial states show that the surrogate reproduces key trends of high-fidelity models while substantially reducing computational cost. The resulting capability bridges physics fidelity and performance, providing a practical path to a predictive, microstructure-aware assessment of creep and fracture in reactor materials.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

You Only Look Once v5 and Multi-Template Matching for Small-Crack Defect Detection on Metal Surfaces

This paper compares the performance of Deep Learning (DL) and multi-template matching (MTM) models for detecting small defects. DL models extract distinguishing features of objects but require a large dataset of images. In contrast, alternative computer vision techniques like MTM need a relatively small dataset. The lack of large datasets for small metal-surface defects has inhibited the adoption of automation in small-defect detection in remanufacturing settings. This motivated this preliminary study to compare template-based approaches, like MTM, with feature-based approaches, such as DL models, for small-defect detection on an initial laboratory and remanufacturing industry dataset. This study used You Only Look Once v5 (YOLOv5) as the DL model and compared its performance against the MTM model for small-crack detection. The findings of our preliminary investigation are as follows: (i) YOLOv5 demonstrated higher performance than MTM in detecting small cracks; (ii) an extra-large variant of YOLOv5 outperformed a small-size variant; (iii) the size and object variety of the data are crucial in achieving robust pre-trained weights for use in transfer learning; and (iv) enhanced image resolution contributes to precise object detection.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Improving the Concrete Crack Detection Process via a Hybrid Visual Transformer Algorithm

Inspections of concrete bridges across the United States represent a significant commitment of resources, given their biannual mandate for many structures. With a notable number of aging bridges, there is an imperative need to enhance the efficiency of these inspections. This study harnessed the power of computer vision to streamline the inspection process. Our experiment examined the efficacy of a state-of-the-art Visual Transformer (ViT) model combined with distinct image enhancement detector algorithms. We benchmarked against a deep learning Convolutional Neural Network (CNN) model. These models were applied to over 20,000 high-quality images from the Concrete Images for Classification dataset. Traditional crack detection methods often fall short due to their heavy reliance on time and resources. This research pioneers bridge inspection by integrating ViT with diverse image enhancement detectors, significantly improving concrete crack detection accuracy. Notably, a custom-built CNN achieves over 99% accuracy with substantially lower training time than ViT, making it an efficient solution for enhancing safety and resource conservation in infrastructure management. These advancements enhance safety by enabling reliable detection and timely maintenance, but they also align with Industry 4.0 objectives, automating manual inspections, reducing costs, and advancing technological integration in public infrastructure management.

42 ENGINEERING↗
DOE OSTI2024

Unlocking Larger Scales and Aspect Ratios in 3D Printed Glass: Coupling Active Mixing and UV Curing for Advanced Printability and Crack Resistance

Recent developments in additive manufacturing (AM) of glass via silica-filled inks have facilitated fabrication of previously unattainable geometries and compositions. However, the maximum processable size of 15 mm limits the use of these prints in applications such as optics. A key limitation lies in the trade-off between material printability and green strength: increasing silica content in the feedstock improves crack resistance and reduces shrinkage but results in dramatic changes in viscoelastic properties that hinder flowability. Here, this paper presents a novel approach that offers expanded versatility in processable size, feedstock formulation, and printing. Described here is a direct ink writing (DIW) system coupled with an active high-shear micromixer and UV light source, capable of simultaneously printing multiple inks with a wide range of rheological properties. Choice of silica sourc, solvent, UV-curable binder, and dispersant is used to tune the ink rheology and improve printability and mechanical properties. Imparting high shear with the micromixer while UV-curing the extrudate allows for increased ink viscosities and reduced nozzle diameters, enabling printing finer feature sizes. With these advances, thin-walled high-aspect ratio structures and a crack-free glass disk measuring 44 mm in diameter are demonstrated, an increase of 3× in the greatest dimension compared to current state-of-the-art.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Crack mitigation and wear performance of high-strength steel coatings deposited by high-speed laser cladding

This article investigates the fabrication of defect-free Rockit® 606, a high‑carbon, vanadium- and chromium-enriched precipitation-hardening martensitic steel coating, using high-speed laser cladding (HSLC). Compared to conventional laser cladding, HSLC offers higher deposition efficiency, improved coating quality, minimal thermal distortion, and a reduced heat-affected zone. Various HSLC parameters—including laser power, travel speed, powder feed rate, and overlap distance—were optimized to achieve superior coating properties. Microstructural analysis revealed solidification cracks in coatings deposited on carburized steel, regardless of processing parameters. However, preheating the substrate to 250 °C effectively eliminated cracking by reducing thermal gradients. The coatings exhibited a columnar dendritic microstructure, with coarser dendrites near the substrate and finer dendrites towards the surface. Hardness measurements confirmed that all coatings significantly exceeded the industry-specified threshold of 60 HRC, with preheating having minimal effect on overall hardness distribution. Reciprocating sliding wear tests demonstrated a substantial improvement in wear resistance for the defect-free HSLC coatings compared to baseline carburized steel. These findings underscore the potential of HSLC for producing high-performance, wear-resistant coatings suitable for industrial applications.

36 MATERIALS SCIENCE↗