Search NASA⌕ Search

SEARCH · Search NASA

Results for “crosslinked electrolyte”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

65 records · Page 4

Ionomer Optimization for Water Uptake and Swelling in Anion Exchange Membrane Electrolyzer: Hydrogen Evolution Electrode

Green hydrogen produced through anion exchange membrane water electrolysis is a promising, low-cost chemical storage solution for intermittent renewable energy sources. Low-temperature electrolysis using anion exchange membranes (AEM) combines the benefits of established water electrolysis technologies based on alkaline electrolysis and proton exchange membrane electrolysis. The anion conductive ionomers (ACI) used in the AEM electrolyzer (AEMEL) electrodes has been investigated. The ACI serves two primary purposes: (i) facilitate hydroxide conduction between the catalyst and bulk electrolyte and (ii) bind the catalyst to the porous transport layer and membrane. High ion exchange capacity (IEC) ACIs are desired, however, high IEC can cause excessive water uptake (WU) and detrimental ACI swelling. Proper water management is a key factor in obtaining maximum performance in AEM-based devices. In this study, a series of poly(norbornene)-based ACIs were synthesized and deployed in hydrogen evolving AEMEL cathode electrodes. A balance between ionic conductivity, WU and ionomer swelling was achieved in the ACI by varying the IEC and degree of polymer cross-linking. It was found that higher IEC ACIs with light crosslinking are preferred in the HER electrode. Furthermore, such a configuration fine-tuned the WU and ionomer swelling to achieve optimum cell performance and reduce cell operating voltages.

08 HYDROGEN↗

Progress of 3D network binders in silicon anodes for lithium ion batteries

Prompted by its overwhelming benefits, silicon (Si) has evolved as one of the most promising anode materials for high-capacity lithium-ion batteries (LIBs). However, some of the intrinsic drawbacks such as low ionic conductivity and inevitable volume change during the alloying/dealloying process seriously hamper the commercialization of Si-based anodes in LIBs. Among the several strategies to overcome the challenges of the Si anode, the development of designed polymeric binders is imperative for enabling stable and satisfactory performance. The improved cell performance due to the designed binders is recognized as an economical and practical approach, especially from the industrial perspective. In addition to their conventional role in integrating electrode components, binders also play a significant role in alleviating the unfavorable phenomenon of volume expansion, and ultimately stabilizing the Si anode and Si-electrolyte interphase. The polymer architecture of the binders significantly influences the binder performance, and three-dimensional (3D) network binders are generally more effective at coping with the stress resulting from the huge volume change of the Si anode. To develop advanced 3D binders, substantial research efforts have been made including various crosslinking strategies in the past decade. In this review, we focus on diverse crosslinking methods including chemical-, physical-, and topological-crosslinking for rationally designing network binders for Si anodes and take a glance at dynamic interactions to construct healable binders for long-term stability.

25 ENERGY STORAGE↗

Highly swollen ROMP-based gels

In this study, the leakage of organic solvent during the transportation and storage is one of the major threats to the environment. Networks/gels acting as the absorbing materials for organic solvents are the most promising solution for the organic solvent pollution. Here, we report the synthesis of highly swollen networks/gels in high yield (≥95%) via ring opening metathesis polymerization (ROMP) using Grubbs’ first generation catalyst/initiator (G1), a crosslinker (1,1'-(methylenedi-4,1-phenylene)bis-exo-7-oxanorbornenecarboximide) and monofunctional monomer/diluent (exo-N-phenyl-7-oxanorbornenecarboximide). The mesh size of the network was varied by keeping the concentration of monomer constant while changing the concentrations of crosslinker and G1 (initiator). The swelling capacity of the network in N,N-dimethylformamide (DMF) solvent increased from 41 to 53 and to 61 with the increase of theoretical mesh size (molar ratio of monomer to crosslinker) from 20 to 40 and to 60, respectively. By further increasing the mesh size from 60 to 80 there was no significant change in swelling capacities (63). Thus, the gel with the mesh size of 60 was selected for swelling capacity analysis in other polar organic solvents such as dimethyl sulfoxide (DMSO), dichloromethane (DCM), chloroform and lithium-ion battery electrolyte solution (1.0 M LiPF 6 in ethylene carbonate (EC)/diethyl carbonate (DEC) = 50/50 (v/v)). They showed the decreased swelling capacity value from 61 to 57, 40, 31 and 5, respectively. For a controlled mesh size ROMP-based gel, we observed the highest swelling capacity values to date.

36 MATERIALS SCIENCE↗

Graphene macro-assembly-fullerene composite for electrical energy storage

Disclosed here is a method for producing a graphene macro-assembly (GMA)-fullerene composite, comprising providing a GMA comprising a three-dimensional network of graphene sheets crosslinked by covalent carbon bonds, and incorporating at least 20 wt. % of at least one fullerene compound into the GMA based on the initial weight of the GMA to obtain a GMA-fullerene composite. Also described are a GMA-fullerene composite produced, an electrode comprising the GMA-fullerene composite, and a supercapacitor comprising the electrode and optionally an organic or ionic liquid electrolyte in contact with the electrode.

25 ENERGY STORAGE↗

Graphene macro-assembly-fullerene composite for electrical energy storage

Disclosed here is a method for producing a graphene macro-assembly (GMA)-fullerene composite, comprising providing a GMA comprising a three-dimensional network of graphene sheets crosslinked by covalent carbon bonds, and incorporating at least 20 wt. % of at least one fullerene compound into the GMA based on the initial weight of the GMA to obtain a GMA-fullerene composite. Also described are a GMA-fullerene composite produced, an electrode comprising the GMA-fullerene composite, and a supercapacitor comprising the electrode and optionally an organic or ionic liquid electrolyte in contact with the electrode.

25 ENERGY STORAGE↗

Synthesis of highly sulfonated 2,6-diphenyl-p-Phenylene oxide: A highly conductive membrane

Highly sulfonated aromatic polymers are desired for the possible highest performance of polymer electrolytes in fuel cells and electrolyzer applications. Here, we reported the method to prepare highly sulfonated 2,6-diphenyl-p-phenylene oxide (SP3O), a commercially available aromatic polymer, with the highest IEC of 4.42 meq/g. Three sulfonation reagents including chlorosulfonic acid (HSO3Cl), concentrated sulfuric acid (conc. H2SO4), and trimethylsilyl chlorosulfonate (TMSCS) were investigated for single and two-step sulfonation reactions. In addition, DMSO-assisted thermal crosslinking method was applied to prepare crosslinked SP3O membranes to improve their mechanical strength and film-forming ability. Proton exchange membrane from crosslinked SP3O displayed a proton conductivity as high as 250 mS/cm at 95 % RH and 60 °C.

Khomein, Piyachai↗

An inverse vulcanized conductive polymer for Li–S battery cathodes

Polymers with a broad range of properties, structural diversity, and mechanical flexibility have been adopted in all aspects of Li–S batteries. However, currently explored polymers for Li–S cathodes suffer from low conductivity, low S content, and poor cycling performance. In this first-principles study, we theoretically design a new polymer, poly(2-vinyl,1,4-phenylene sulfide), by modifying the conductive poly(1,4-phenylene sulfide) via the vinyl group to enhance its ability to vulcanize with element S. Furthermore, we compare the properties of the experimentally realized sulfur vulcanized polymers via condensation and our designed sulfur vulcanized polymers via crosslinking as Li–S battery cathodes, in terms of gravimetric and specific capacities, as well as structural stability during the lithiation. Overall, we find that our designed polymer possesses better conductivity, higher specific capacity and gravimetric energy density, and better kinetic stability, and restricts the shuttle effect more efficiently than the current experimentally explored one. Also, the cross-linked sulfur compounds can be activated efficiently due to the short transport lengths rather than dissolution in the electrolyte during battery operation. Therefore, we believe our designed polymer cathode is promising for practical applications.

25 ENERGY STORAGE↗

Poly(cyclohexadiene)-Based Polymer Electrolyte Membranes for Fuel Cell Applications

The goal of this research project was to create and develop fuel cell membranes having high proton conductivity at high temperatures and high chemical and mechanical durability. Poly(1,3-cyclohexadiene) (PCHD) is of interest as an alternative polymer electrolyte membrane (PEM) material due to its ring-like structure which is expected to impart superior mechanical and thermal properties, and due to the fact that PCHD can readily be incorporated into a range of homopolymer and copolymer structures. PCHD can be aromatized, sulfonated, or fluorinated, allowing for tuning of key performance structure and properties. These factors include good proton transport, hydrophilicity, permeability (including fuel gas impermeability), good mechanical properties, morphology, thermal stability, crystallinity, and cost. The basic building block, 1,3-cyclohexadiene, is a hydrocarbon monomer that could be inexpensively produced on a commercial scale (pricing typical of other hydrocarbon monomers). Optimal material properties will result in novel low cost PEM membranes engineered for high conductivity at elevated temperatures and low relative humidities, as well as good performance and durability. The primary objectives of this project were: (1) To design, synthesize and characterize new non-Nafion PEM materials that conduct protons at low (25-50%) RH and at temperatures ranging from room temperature to 120 C; and (2) To achieve these objectives, a range of homopolymer and copolymer materials incorporating poly(cyclohexadiene) (PCHD) will be synthesized, derivatized, and characterized. These two objectives have been achieved. Sulfonated and crosslinked PCHD homopolymer membranes exhibit proton conductivities similar to Nafion in the mid-RH range, are superior to Nafion at higher RH, but are poorer than Nafion at RH < 50%. Thus to further improve proton conductivity, particularly at low RH, poly(ethylene glycol) (PEG) was incorporated into the membrane by blending and by copolymerization. Conductivity measurements at 120 C over RH ranging from 20 to 100% using the BekkTech protocol showed much improved proton conductivities. Conductivities for the best of these new membranes exceed the DOE Year 3 milestone of 100 mS/cm at 50% RH at 120 C. Further optimization of these very promising low cost membranes could be pursued in the future.

08 HYDROGEN↗

Molecular Layer Deposition of Crosslinked Polymeric Lithicone for Superior Lithium Metal Anodes

In this work, we for the first time developed a novel lithium-containing crosslinked polymeric material, a lithicone that enables excellent protection effects over lithium (Li) metal anodes. This new lithicone was synthesized via an accurately controllable molecular layer deposition (MLD) process, in which lithium tert -butoxide (LTB) and glycerol (GL) were used as precursors. The resultant LiGL lithicone was analyzed using a suite of characterizations. Furthermore, we found that the LiGL thichicone could serve as an exceptional polymeric protection film over Li metal anodes. Our experimental data revealed that the Li electrodes coated by this LiGL lithicone can achieve a superior cycling stability, accounting for an extremely long cyclability of >13,600 Li-stripping/plating cycles and having no failures so far in Li/Li symmetric cells at a current density of 5 mA/cm 2 and an areal capacity of 1 mAh/cm 2 . We found that, with a sufficient protection by this LiGL coating, Li electrodes could realize long-term stable cyclability with little formation of Li dendrites and solid electrolyte interphase. This novel LiGL represents a facile and effective solution to the existing issues of Li anodes and potentially paves a technically feasible route for lithium metal batteries.

Meng, Xiangbo↗