Search NASA⌕ Search

SEARCH · Search NASA

Results for “dark energy experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

67 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1961

A Satellite Borne Cadmium Sulfide Total Corpuscular Energy Detector

The properties of single crystals of cadmium sulfide as radiation detectors are described. It has been found possible to select crystals such that: (a) The ratio of increase of conductivity under irradiation to the rate of absorption of energy in the crystal is substantially independent of particle energy (over the examined ranges of 500 ev to 80 kev for electrons and 5 kev to 180 kev for protons) and of the magnitude of energy flux (over the range from.005 to 10 ergs/cm(sup 2 -sec); and (b) The above ration is substantially the same for protons, electrons, alpha particles, x-rays, and gamma-rays. For a driving voltage of 100 volts, typical crystal yield currents of 10(sup -7) to 10(sup- 6) amperes for each erg/cm(sup 2-sec) of energy absorbed by the crystal. The threshold of such crystal detectors (resulting from dark currents of the order of 10(sup 10 amp) is typically 10(sup -3) ergs/cm(sup 2- sec). For the selected crystals a response-temperature coefficient of -0.25% per degree centigrade is found for the temperature range -50 deg C to + 50 deg C. A description is given of a complete CdS total corpuscular energy detector for the study of geomagnetically trapped radiation by means of a satellite. The detector described has a dynamic range great than 10(sup 4), a solid angle of 10(exp -3) steradian, and a detection threshold of approximately 1 erg/cm(sup 2-sec-sterad). A similar detector employing a small magnet for the selective exclusion of electrons is also described. Noteworthy practical features of these detectors for satellite and space probe experiments are: (a) Use of bare crystals, without covering foils, in order to detect charged particles having energies as low as hundreds of electron volts. (b) Simplicity of electronic auxiliaries. (c) Compactness, lightweight and nechanical ruggedness. (d) Low electrical power requirements; and (e) Conversion of conduction current to the rate of a twostate relaxation oscillator in order to facilitate telemetric transmission of data. A pair of such detectors was flown as part of the s-46 satellite payload on March 23, 1960, but due to vehicular failure an orbit was not achieved and the operation of the CdS detectors was observed for only, six minutes of flight.

Freeman, John W.↗
NASA NTRS2021

Indirect Dark Matter Searches at Ultrahigh Energy Neutrino Detectors

High to ultrahigh energy neutrino detectors can uniquely probe the properties of dark matterχby searching for the secondary products produced through annihilation and/or decay processes. We evaluate the sensitivities to dark matter thermally averaged annihilation cross section〈σv〉and partial decay width into neutrinos Γ χ→ν ̄ν (in the mass scale 10 7 ≤ m χ /GeV ≤ 10 15 ) for next generation observatories like POEMMA and GRAND. We show that in the range 10 7 ≤ m χ /GeV ≤ 10 11 , space-based Cherenkov detectors like POEMMA have the advantage of full-sky coverage and rapid slewing, enabling an optimized dark matter observation strategy focusing on the Galactic center. We also show that ground-based radio detectors such as GRAND can achieve high sensitivities and high duty cycles in radio quiet areas. We compare the sensitivities of next generation neutrino experiments with existing constraints from IceCube and updated 90% C.L. upper limits on〈σv〉and Γ χ→ν ̄ν using results from the Pierre Auger Collaboration and ANITA. We show that in the range 10 7 ≤ m χ /GeV ≤ 10 11 POEMMA and GRAND10k will improve the neutrino sensitivity to particle dark matter by factors of 2 to 10 over existing limits, whereas GRAND200k will improve this sensitivity by two orders of magnitude. In the range 10 11 ≤ m χ /GeV ≤ 10 15 , POEMMA’s fluorescence observation mode will achieve an unprecedented sensitivity to dark matter properties. Finally, we highlight the importance of the uncertainties related to the dark matter distribution in the Galactic halo, using the latest fit and estimates of the Galactic parameters.

Particle astrophysics↗
NASA NTRS2021

Understanding the Space Weathering of Mercury Through Laboratory Experiments

Introduction: Airless surfaces across the solar system are continually modified by energetic particles from solar wind and micrometeoroid bombardment [1,2]. This process is known as space weathering, and it alters the chemical, microstructural, and optical properties of surface regoliths on airless bodies, including Mercury. On the Moon and S-type asteroids, the reflectance spectral signatures of space weathering include reddening (increasing reflectance with increasing wavelength), darkening (lowering of reflectance), and the attenuation of characteristic absorption bands [2]. Such spectral changes are driven by the production of Fe-bearing nanoparticles(npFe) through both solar wind irradiation and micrometeoroid bombardment. While our understanding of space weathering for the Moon and near-Earth S-types asteroids is advanced, insight into how these processes operate on other planetary bodies is limited. In particular, Mercury experiences a uniquely intense space weathering environment than planetary counterparts at 1 AU, including a moreintense solar wind flux and higher velocity micrometeoroid impacts [4]. Additionally, Mercury has a surface composition unique in the inner solar system, including regions of the surface with very low albedo known as the low reflectance material (LRM), which is enriched in carbon, likely graphite, up to 4wt.% [5].In addition, the concentration of Fe across Mercury’s surface islow (<2 wt.%) compared to the Moonor S-type asteroids asteroids[6]. Our understanding of the effects of space weathering on C-rich and Fe-poor phases is limited. Since Fe plays a critical role inthe development of space weathering characteristicson other airless surfaces(e.g., npFe), its limited availability may significantly affect the development of space weathering features in Mercury surface materials. We can simulate space weathering processes in the laboratory to explore their effects on the microstructural, chemical, and spectral characteristics of Mercury surface materials[7]. Here we used pulsed laser irradiation to simulate the short duration, high-temperature events associated with micrometeoroid impacts. We performed coordinated analyses including reflectance spectroscopy and electron microscopy to investigate the spectral, chemical, and microstructural changes in these mercurian analog samples. Methods: For these experiments, we usedforsteritic olivine with varying FeOcontents, a mineral phase proposed to be abundant on the surface of Mercury. We mixed each sample with graphite to simulate LRM regions of the surface. Wesynthesized the olivinesamplesat 1-bar at NASA’s Johnson Space Centerand prepared pressed powder pellets for laser irradiation [8].We prepared three samples, each with a base layer of olivineto maintain structural integrity and topped witha surface layer containing the graphite-olivine mixture: 1) Sample SC-001 San Carlos olivine(Fo90.91),2)Sample F-S-002 with0.05 wt.% FeO olivine, and 3) F-T-004 with 0.53 wt.% FeO olivine. Each sample was mixed with 5 wt.% powdered graphite and had grain sizes ranging from 45to 125μm. We irradiated each sample usinga pulsed Nd-YAG laser, (l=1064 nm, ~6 ns pulse duration, energy of 48 mJ/pulse) while undervacuumat Northern Arizona University. The laser was rastered1x and then 5x over the surfaceof each sample to simulate progressive space weathering. We collected in situreflectance spectra from the samples after each laser pulse witha Nicolet IS50 Fourier-Transform Infrared spectrometer (lfrom 0.65-2.5 μm). We used an FEI Nova NanoSEM200scanning electron microscope (SEM) and a Hitachi TM4000 Plus benchtop SEM at Purdue University to image the surface morphology and topography of the samples. We extracted thin sections for analysis in the transmission electron microscope(TEM)using the FEI Helios NanoLab 660 focused ion beam (FIB) SEM at the University of Arizona.We performed analysis of the microstructural and chemical characteristics of the samples using the 200 keV JEOL 2500 scanning TEM at Johnson Space Center. Reflectance Spectroscopy Results:Reflectance spectra for each sample are shown in Fig. 1.SC-001:The spectrum of the unirradiated sample exhibits a weak 1.0 μm absorption feature, associated with Fe2+in the olivine,and low overall reflectance (Fig. 1a). Thereflectance and the depth of the absorption band increases after 1x laser raster but are at their lowest after 5x laser rasters.F-T-004:The unirradiated sample has a blue-sloped spectrum with low reflectance without identifiable absorption features (Fig. 1b). With progressive laser irradiation, the sample reflectance increases and becomes strongly red-sloped.F-S-002:The unirradiated sample exhibits a dark, blue-slopedspectrum. The brightness of the sample increases significantly from <0.2average reflectance over >0.8 reflectance in the most irradiated sampleand thespectral slope also becomesslightly reddened (Fig. 1c). Microstructural and Chemical Analysis: Two primary alteration textures were observed in the samples exposed to simulated space weathering: 1) fluffy C-rich,and 2) vesiculated melt. The fluffy C-rich texture is composed oflow-densitydeposits distributed across the surface of the sample(Fig. 2A). Analysis of a FIB section extracted from a low-density C-rich region in sample SC-001 reveals multiple globule-type deposits, discrete from stacked graphite, likely produced via melting from the laser irradiation [9].The vesiculated melt textureis smooth and uniformly distributed across isolated regions of the sample surface. The vesicles measure up to 100s of nmin diameter. Analysis of a FIB section from this texture was extracted from sample F-T-004 reveals a layer of amorphous melt material, close to 100 nm thick and uniform across the FIB section (Fig. 2B). Isolated regions of this melt layer contain small nanoparticles, <5 nm in diameter. Chemical analysis through energy dispersive X-ray spectroscopy reveals the composition of this layer is enriched in Si and depleted in Mg and O compared to the underlying sample. Implications for Space Weathering on Mercury: Previous experiments simulating space weathering of Mercury have showndarkening and reddening of spectra[7,10].However, our use of low-Fe materials and graphite to create a sample set more analogous to the mercurian surface. Our results indicate that sample composition plays a significant and important role in the space weathering of Mercury. In particular, our spectral data demonstrates a strong correlation between spectral slope, Fe content, and simulated space weathering. While the variation in FeO content between samples F-S-002 and F-T-004 is <0.6 wt.%, the spectra deviate from flat to strongly red-sloped(F-T-004). This reddeningmay be linked to the presence of very small nanoparticles observed in the melt textures extracted from sample F-T-004. For the SC-001 sample, the fluffy C-rich textures may be developed by the amalgamation of small graphite particles into these unique morphologies. Such observations indicate that space weathering on Mercury may result in both familiar and new microstructural and chemical characteristics. References: [1]Hapke B. (2001) J. Geophys. Res.-Planet.,106,10039–10073. [2]Pieters C.M. and Noble S.K. (2016) J. Geophys. Res-Planet., 121, 1865–1884. [3] Lucey P.G., and Riner, M.A. (2011) Icarus,212, 451-462.[4]CintalaM.J.(1992)J. Geophys. Res.-Planet.,97,947–973.[5]Klima R.L.et al.(2018)Geophys.Res.Letters, 45, 2945–2953. [6]Nittler L.R., et al. (2011) Science 333, 1847-1850.[7]Sasaki S. and Kurahashi E. (2004) Space weathering on Mercury, Adv.Space Res., 33, 2152-2155.[8] Vander KaadenK.E., et al. (2018) LPSCXLIX, Abstract 1230. [9] McGlaun M.L. et al. (2019) LPSCL, Abstract 2019. [10] TrangD.et al. (2018)LPSCXLIX,Abstract2083

M S Thompson↗
NASA NTRS1998

Evaluation of the Use of Dark and Bright Targets for the In-Flight Calibration of AVIRIS

During a field campaign at Lake Tahoe on June 22, 1995, calibrations of AVIRIS were attempted using both the reflectance-based and radiance-based methods. This experiment shows that the use of dark water targets to calibrate radiometric sensors can result in meaningful sensor characterization. In particular, the reflectance-based method shows promise towards meeting the desired 2-3% uncertainty levels for ocean color sensors since experimental agreement of better than 1.5% is found for the Lake Tahoe AVIRIS experiment. Similarly promising results were found from reflectance-based calibrations at Lunar Lake with large portions of the spectrum having less than a 5% difference between the reflectance-based predictions and the measured AVIRIS radiances. These results are still in the preliminary stage and it is likely that further study of this data set will lead to even better agreement. The results of the radiance-based calibration at Lake Tahoe are quite good at the shorter wavelengths where atmospheric scattering leads to larger signals and smaller effects of specularly reflected solar energy. The results also showed the sensitivity to radiometer pointing when using water targets for vicarious calibration.

K. Thome↗
NASA NTRS1996

Comet Shoemaker-Levy 9, Jupiter, and Impact Shock Chemistry

Four years ago this month, a hitherto unknown comet in loose orbit around Jupiter passed so near the giant planet that it was torn apart into 20 fragments by tides. One orbit later, two years ago this month, the fragments of doomed comet P/Shoemaker Levy (SL9) fell into Jupiter. The enormous energies of these impacts (the largest fragments were nearly 1 km across and, hitting at 60 km/s, released some 2-4 x 10(exp 27) ergs) produced enormous explosions. Several of the ejecta plumes were imaged towering 3000 km above Jupiter's limb. The heat released when the plumes fell was considerable and easily observed on Earth. The impacts produced strong shocks, both promptly at the impact site and again, later, and over thousands of kilometers, when the ejecta plume reentered the atmosphere. The focus of this talk will be to discuss what the SL9 impacts taught us about impact shock chemistry - the processes, the ingredients, the results - and what inferences we may draw for impacts on early Earth. Shock chemistry generates a suite of molecules not usually seen on Jupiter. The most surprising report was of a huge amount of diatomic sulfur S2 at the site of the G impact. Other unusual products include CS, CS2, OCS, H2S, SO2, HCN, CO, and H2O; although H2S and H2O are doubtless abundant below the visible clouds. Hot or enhanced CH4 and NH3 were also detected. A general rule of shock chemistry is that CO forms until either C or O is exhausted. If O greater than C, the other products are oxidized, and excess O goes to H2O. If C greater than O, the other products are reduced, and excess C goes to HCN, C2H2, and a wide variety of more complicated organics. Ultimately, given time, the carbon would react all the way to graphite, but in practice the reactions are incomplete. The dark ejecta debris were probably composed in part of carbonaceous particles generated by the shocks. In a sense, the SL9 impacts performed the famous Miller-Urey experiment on a grand scale, with one result being the production of a lot of complex brown organic solids (called "tholins"). We use, a straightforward chemical kinetics model for the H, N, C, O, S system to follow the nonequilibrium chemistry behind the shocks. The model traces the evolving chemical composition of a parcel of gas by directly integrating the web of chemical reactions. Pressure and temperature histories of the parcels are patterned after those calculated by numerical hydrodynamic simulations of the ejecta plume. A given plume parcel is generally shocked twice; t.e a parcel shocked near the impact site is ejected at high velocity and is shocked again when it reenters the atmosphere. The final state of the gas depends mostly on the second shock, provided that the latter is hot enough. The chemical evidence is ambiguous, but most indications are that C greater than O in the shocked, reacting gas. Telltale signatures of abundant oxygen - SO2, SO, CO2, O2 - were not seen, while signatures of abundant carbon - CS, CS2, and HCN - were. On the other hand, abundant H2O would appear to require O greater than C, and two other observed sulfur species, S2 and OCS, appear to form more easily in a somewhat oxidized gas, presumable vaporized from the comet itself. Since on general principles one expects the -comet to have had a more-or-less cosmic composition, i.e. O greater than C, the production of CS, CS2, and HCN probably requires C greater than O in the shocked jovian air. This in turn implies that even the largest fragments released the bulk of their energy above the jovian water table, in all likelihood above 5 bars . There is no evidence in favor of the proposition that a significant amount of wet jovian air was shocked strongly enough to coax water to react; i.e. wet jovian air saw only temperatures significantly below 2000 K.

Zahnle, Kevin↗
NASA NTRS2019

The Simons Observatory: Science Goals and Forecasts

The Simons Observatory (SO) is a new cosmic microwave background experiment being built on CerroToco in Chile, due to begin observations in the early 2020s. We describe the scientific goals of the experiment, motivate the design, and forecast its performance. SO will measure the temperature and polarization anisotropy of the cosmic microwave background in six frequency bands centered at: 27,39, 93, 145, 225 and 280 GHz. The initial configuration of SO will have three small-aperture 0.5-mtelescopes and one large-aperture 6-m telescope, with a total of 60,000 cryogenic bolometers. Our key science goals are to characterize the primordial perturbations, measure the number of relativistic species and the mass of neutrinos, test for deviations from a cosmological constant, improve our understanding of galaxy evolution, and constrain the duration of reionization. The small aperture telescopes will target the largest angular scales observable from Chile, mapping≈10% of the sky to a white noise level of 2μK-arcmin in combined 93 and 145 GHz bands, to measure the primordial tensor-to-scalar ratio, r, at a target level ofσ(r) = 0.003. The large aperture telescope will map ≈40% of the sky at arcminute angular resolution to an expected white noise level of 6μK-arcminin combined 93 and 145 GHz bands, overlapping with the majority of the Large Synoptic Survey Telescope sky region and partially with the Dark Energy Spectroscopic Instrument. With up to an order of magnitude lower polarization noise than maps from the Planck satellite, the high-resolution sky maps will constrain cosmological parameters derived from the damping tail, gravitational lensing of the microwave background, the primordial bispectrum, and the thermal and kinematic Sunyaev–Zel’dovich effects, and will aid in delensing the large-angle polarization signal to measure the tensor-to-scalar ratio. The survey will also provide a legacy catalog of 16,000 galaxy clusters and more than20,000 extragalactic sources.

Peter Ade↗
NASA NTRS2019

The Simons Observatory: science goals andforecasts

The Simons Observatory (SO) is a new cosmic microwave background experiment being built on Cerro Toco in Chile, due to begin observations in the early 2020s. We describe the scientific goals of the experiment, motivate the design, and forecast its performance. SO will measure the temperature and polarization anisotropy of the cosmic microwave background in six frequency bands centered at: 27, 39, 93, 145, 225 and 280 GHz. The initial configuration of SO will have three small-aperture 0.5-m telescopes and one large-aperture 6-m telescope, with a total of 60,000 cryogenic bolometers. Our key science goals are to characterize the primordial perturbations, measure the number of relativistic species and the mass of neutrinos, test for deviations from a cosmological constant, improve our understanding of galaxy evolution, and constrain the duration of reionization. The small aperture telescopes will target the largest angular scales observable from Chile, mapping ≈ 10% of the sky to a white noise level of 2 μK-arcmin in combined 93 and 145 GHz bands, to measure the primordial tensor-to-scalar ratio, r, at a target level of σ(r)=0.003. The large aperture telescope will map ≈ 40% of the sky at arcminute angular resolution to an expected white noise level of 6 μK-arcmin in combined 93 and 145 GHz bands, overlapping with the majority of the Large Synoptic Survey Telescope sky region and partially with the Dark Energy Spectroscopic Instrument. With up to an order of magnitude lower polarization noise than maps from the Planck satellite, the high-resolution sky maps will constrain cosmological parameters derived from the damping tail, gravitational lensing of the microwave background, the primordial bispectrum, and the thermal and kinematic Sunyaev-Zel'dovich effects, and will aid in delensing the large-angle polarization signal to measure the tensor-to-scalar ratio. The survey will also provide a legacy catalog of 16,000 galaxy clusters and more than 20,000 extragalactic sources.

Peter Ade↗
NASA NTRS2013

Nanoscale Mineralogy and Composition of Experimental Regolith Agglutinates Produced under Asteroidal Impact Conditions

On the Moon, the energetics of smaller impactors and the physical/chemical characteristics of the granular regolith target combine to form a key product of lunar space weathering: chemically reduced shock melts containing optically-active nanophase Fe metal grains (npFe0) [1]. In addition to forming the optically dark glassy matrix phase in lunar agglutinitic soil particles [1], these shock melts are becoming increasingly recognized for their contribution to optically active patina coatings on a wide range of exposed rock and grain surfaces in the lunar regolith [2]. In applying the lessons of lunar space weathering to asteroids, the potential similarities and differences in regolith-hosted shock melts on the Moon compared to those on asteroids has become a topic of increasing interest [3,4]. In a series of impact experiments performed at velocities applicable to the asteroid belt [5], Horz et al. [6] and See and Horz [7] have previously shown that repeated impacts into a gabbroic regolith analog target can produce melt-welded grain aggregates morphologically very similar to lunar agglutinates [6,7]. Although these agglutinate-like particles were extensively analyzed by electron microprobe and scanning electron microscopy (SEM) as part of the original study [7], a microstructural and compositional comparison of these aggregates to lunar soil agglutinates at sub-micron scales has yet to be made. To close this gap, we characterized a representative set of these aggregates using a JEOL 7600 field-emission scanning electron microscope (FE-SEM), and JEOL 2500SE field-emission scanning transmission electron microscope (FE-STEM) both optimized for energy dispersive X-ray spectroscopy (EDX) compositional spectrum imaging at respective analytical spatial resolutions of 0.5 to 1 micron, and 2 to 4 nm.

Christoffersen, Roy↗
NASA NTRS2004

Effects of heavy ions on visual function and electrophysiology of rodents: the ALTEA-MICE project

ALTEA-MICE will supplement the ALTEA project on astronauts and provide information on the functional visual impairment possibly induced by heavy ions during prolonged operations in microgravity. Goals of ALTEA-MICE are: (1) to investigate the effects of heavy ions on the visual system of normal and mutant mice with retinal defects; (2) to define reliable experimental conditions for space research; and (3) to develop animal models to study the physiological consequences of space travels on humans. Remotely controlled mouse setup, applied electrophysiological recording methods, remote particle monitoring, and experimental procedures were developed and tested. The project has proved feasible under laboratory-controlled conditions comparable in important aspects to those of astronauts' exposure to particle in space. Experiments are performed at the Brookhaven National Laboratories [BNL] (Upton, NY, USA) and the Gesellschaft fur Schwerionenforschung mbH [GSI]/Biophysik (Darmstadt, FRG) to identify possible electrophysiological changes and/or activation of protective mechanisms in response to pulsed radiation. Offline data analyses are in progress and observations are still anecdotal. Electrophysiological changes after pulsed radiation are within the limits of spontaneous variability under anesthesia, with only indirect evidence of possible retinal/cortical responses. Immunostaining showed changes (e.g. increased expression of FGF2 protein in the outer nuclear layer) suggesting a retinal stress reaction to high-energy particles of potential relevance in space. c2004 COSPAR. Published by Elsevier Ltd. All rights reserved.

NASA Center JSC↗
NASA NTRS2012

Radar Scattering and Block Size Properties of Lunar Crater Ejecta From Mini-RF and LROC NAC Data

A major objective of the Mini-RF experiment is to distinguish lunar surfaces that may contain water/ice deposits [1,2]. Better understanding of the backscattering properties of craters of varying age and size is crucial for interpreting data received from the Mini-RF. The Mini-RF transmits a circularly polarized RF electromagnetic energy and coherently receives orthogonal linear polarization echoes [1]. The Mini- RF maps in two separate bands ( =12.6 and 4.5 cm) at a high resolution mode of 30 m/pixel [1]. Given the variables mentioned, the four stokes parameters are reconstructed. The Circular Polarization Ratio (CPR) is calculated for the purposes of understanding subsurface and surface roughness. The CPR is determined from reflections acquired from the ratio of power of the transmitted radio wave in same sense to the reflected radio wave in the opposite sense [1]. Ice in the permanently shadowed regions (PSRs) would be transparent to radar, but the inclusions of materials and imperfections would cause the radio wave to reflect multiple times [3], enhancing the number of same sense reflections and increasing the CPR. In addition, ice also displays the coherent backscatter opposition effect (CBOE), an interferrometric addition of same sense backscatter that further increases the CPR of ice targets [7]. High CPR values also correlate to multiple reflections and are typically associated with very rough surfaces [3]. The average dry lunar surface has a CPR in the range of 0.2-0.4 at 48deg incidence [3]. The purpose of this study is to begin to quantify degrees of surface wavelength-scale roughness with CPR and to understand how such surface roughness is created and gradually destroyed by erosion on the lunar surface. Another goal is to identify and isolate the possible causes of high CPR within the shadowed areas of anomalous polar craters [3]. All the studied craters are non-polar, so that we can see into their interiors in NAC images. The idea is to understand what controls blockiness in these craters so that we can rule out rocks (and rule in ice) for the anomalous polar dark ones [3].

Spudis, P. D.↗
NASA NTRSDate not supplied

X-Ray Missions Based on LTD Technologies

Microcalorimeter arrays used as imaging spectrometers will enable ground-breaking science in X-ray astrophysics. Their development has been one of the driving applications of the low temperature detector community since the early 1980s. While their application in space remains in relative infancy, we are on the verge of an era in which microcalorimeter spectrometers are likely to dominate instrumentation for high-energy astrophysics missions. NASA sounding rocket experiments such as the X-ray Quantum Calorimeter (XQC) and Micro-X have now paved the way for orbital observatories. JAXA’s Astro-H gave us a glimpse of this fantastic new capability before its unfortunate demise. The launch of XRISM later this year should finally demonstrate the sort of large suite of observations that X-ray microcalorimeter arrays will make major contributions to. In the mid-2030s, we will see the launch of ESA’s flagship Athena mission, that will further advance the imaging and spectroscopic capabilities for the high-energy X-ray community enormously. Numerous other potential new mission concepts using X-ray microcalorimeters have been studied in detail such as NASA’s Lynx and the Light Element Mapper (LEM), JAXA’s Super-DIOS, and China’s Hot Universe Baryon Surveyor (HUBS). In the first half of this presentation, I will review the development and desired requirements of the X-ray microcalorimeter missions and concepts, and describe the current progress and status missions being implemented and proposed. In the second half of this presentation, I will focus on The Line Emission Mapper (LEM) which is a probe-class mission concept under study by NASA that is designed to provide unprecedented insight into the physics of galaxy formation, including stellar and black-hole feedback and flows of baryonic matter into and out of galaxies. LEM incorporates a light-weight X-ray optic with 10” angular resolution and a large-format microcalorimeter array with a 15” pixel pitch over a 29’ field of view (FOV). The main microcalorimeter array and readout design takes advantage of mature technology that has been developed for Athena X-IFU. The central 7’ region of the array consists of ~ 800 transition-edge sensors (TESs), optimized for a bandpass of 0.3-2 keV and with an energy resolution of 1.2 eV at 1 keV. The rest of the FOV is covered by 4-pixel TES hydras with 2.5 eV energy resolution at 1 keV. Hydras are position-sensitive (‘thermally multiplexed’) detectors that enable extremely large numbers of effective pixels in an array, without a commensurate increase in the number of wires, bias circuit, and readout components. In total the array will have ~ 4k TESs with ~ 14k imaging elements on a 290 micron-pitch. The array will be read out with state-of-the-art time-division multiplexing (TDM), implement with 59 pixels (and 1 dark pixel) in each of the 69 TDM columns. Here we present a detailed overview of the baseline microcalorimeter detector design and present first results from both single pixel TESs and 4-pixel hydras. Our prototype LEM pixels utilize 15um x 50um Mo/Au TESs with a transition temperature of around 58 mK. These pixels incorporate high-fill-factor Au absorbers of thickness 0.54um. We have demonstrated an energy resolution of 0.90+/-0.02 eV and 1.90 +/-0.02 eV at 1.5 keV for single pixel and 4-pixel hydras, respectively, meeting the performance requirements of LEM. We show how the position discrimination in the hydra pixels can be achieved, down to energies of a few 100 eV, using the measured pulse rise-times. Finally, we will show that the properties of the LEM pixels are well optimized for the proposed TDM read out architecture.

Simon Richard Bandler↗
NASA NTRS1976

Missile impact craters (White Sands Missile Range, New Mexico) and applications to lunar research: Contributions to astrogeology

Craters in natural materials at White Sands Missile Range, N. Mex., were produced by the impact of high-velocity to hypervelocity missiles traveling along oblique trajectories with kinetic energies between 2.1 and 81 × 1014 ergs. The oblique impacts produce craters 2 to 10 m across with morphologies and ejecta that are bilaterally symmetrical with respect to the plane of the missile trajectory. Rims are high and the amount of ejecta large in down-trajectory and lateral directions, whereas rims are low to nonexistent and ejecta thin to absent up-trajectory. Symmetry development and modifications of the symmetry are a function of target material, local topography, and angle of impact. Seven mappable units can be recognized in and around the craters. Three of these are ejecta: thick ejecta near the crater, thin to discontinuous ejecta at greater distances, and scattered ejecta at the greatest distances to the limit of throwout. These ejecta units may be absent on the up-trajectory side; if present, they are rarely as thick or continuous as on other sides of the crater. Three units are target materials: undeformed target material exposed in local patches through thin to discontinuous ejecta and everywhere between the fragments of scattered ejecta, tilted and broken target material exposed in upper crater walls, and shattered and fractured target material exposed on the up-trajectory crater wall. The seventh unit is slope material composed of talus and fallback within the crater. Development, character, and exposure of these units varies chiefly with the target material. Ejecta from the craters is chiefly broken but relatively undeformed target material that may range in size from very fine grained debris to large blocks. Where the target is porous, significant amounts of the ejecta are composed of sheared and compressed fragments, some coated with dark layers of mixed projectile pieces, powder, and fused metal mixed with crushed target material. For layered targets, the original stratigraphic sequence is crudely preserved and in inverted order in thick ejecta. Secondary impact craters are produced by the impact of ejected fragments when the surrounding surface materials are sufficiently weak. A wide variety of secondary impact crater relations may result. Secondary craters nearest the primary crater have blocks in them that are larger than or the same size as the crater they produced. Farther from the primary crater, the fragments are generally smaller than the secondary crater and are ejected from it. Excavation of four craters revealed a mixed breccia beneath the crater floor composed of missile pieces, sheared and compressed target material, and crushed debris. Banded, disaggregated target material and nonmixed breccia surrounded the mixed breccia, and these breccias were surrounded by a zone of conjugate fractures. Beneath the ejecta on the lateral and down-trajectory crater flanks, the target materials were tilted upward and broken. Up-trajectory, open fractures and downward displacement occurred in two of the craters. No displacement was observed for the other two. Beneath the down-trajectory rims of craters with distinct layering, overturned synclines were observed. Missile breakup and behavior during cratering are a function of target and missile properties. Missile breakup depends on missile velocity and is most extensive at high velocities, where the missile is fragmented, powdered, and partly fused. Burial of missile or its fragmented, powdered, and fused remains is greatest for porous targets and least for dense cohesive targets. For very porous targets, camouflet structures containing the fragmented missile may form. Least squares fit to the data on craters in dry to moist targets indicate V(a) = 10^(-11.433)E(p)^(1.205) where V(a) is the volume of the apparent crater and E(p) is the kinetic energy of the missile. This equation is consistent with expectations of the equations relating apparent depth and radius to kinetic energy. Extrapolation of displaced masses and kinetic energies for laboratory impacts with sand and rock converge near 10^(15) to 10^(16) ergs, where the extrapolations are near the data on missile impact craters, corrected for impact angle. Displaced masses of craters produced by missile impacts and by chemical explosives with small scaled depths of burial are about the same when the kinetic energies of the missiles (corrected for angle of impact) are equal to the TNT equivalent energy of the explosive. The problem of equivalent scaled depth of burst for an impact crater is complicated and not entirely resolved, however. Both missile impact craters and chemical explosive craters in water-saturated targets are larger than their counterparts in dry to moist materials. Data collected during the study of missile impact craters have helped resolve a number of problems in lunar research: (1) the soillike nature of lunar surface materials was predicted, (2) sizes of craters produced by artificial impacts were correctly predicted, (3) certain features imaged by Surveyor were found to be analogous to features associated with missile impact craters, {4) missile impacts were used in support of the Apollo passive seismic experiment, (5) craters seen in Apollo orbital photographs were found to be similar to some missile impact craters, (6) missile impact craters supplied data on sample collection and crater phenomenology used in training astronauts, and (7) some returned lunar samples are similar to coated, sheared, and compressed fragments ejected from missile impact craters.

H. J. Moore↗
NASA NTRS1998

Proposed Mars Surveyor Landing Sites in Northern Meridiani Sinus, Southern Elysium Planitia, and Argyre Planitia

Our objective is to propose two landing sites that the Mars Surveyor 2001 Lander and Athena Rover could go to on Mars that should meet the safety requirements of the spacecraft landing system and optimize surface operations (chiefly driven by power and communications requirements). An additional site within Argyre Planitia, initially proposed by Parker to the Mars Surveyor Landing Site program, is also proposed for potential consideration for post-2001 missions to Mars, as it is well outside the current latitude limits for the Athena Rover. All three sites are designed to be situated as close to a diversity of geologic units within a few kilometers of the landing site so that diversity can be placed in a geologic context. This objective is very different from the Mars Pathfinder requirement to land at a site with a maximum chance for containing a diversity of rocks within a few tens of meters of the lander. That requirement was driven by the Sojourner mobility limit of a few tens of meters. It can be argued that the Athena project, with its much larger mobility capability, might actually want to avoid such a site, because placing collected samples in geologic context would be difficult. While it has been argued, both before and after the Mars Pathfinder landing, that the provenance for local blocks may be determined by orbiter spectra, primarily from the MGS TES instrument, our ability to do so has yet to be demonstrated. Indeed, several months after conclusion of the Pathfinder mission, we have yet to reach a consensus on the composition of local materials. Our primary data set for selecting a landing site within the latitude and elevation constraints of the 2001 mission is the Viking Orbiter image archive. The site must be selected to place the landing ellipse so as to avoid obvious hazards, such as steep slopes, large or numerous craters, or abundant large knobs. For this purpose, we chose a resolution limit of better than 50 m/pixel. This necessarily excludes from the present study images from current and future orbiter spacecraft, until such data does become readily available. Within each proposed region, it may be possible to identify additional sites once these data become available. Second, the fine-component thermal inertia data, should be greater than about 5 or 6 cgs Units (10(exp -3) cal/sq cm s(exp -0.5)/K). Low thermal inertias imply dusty environments, which could pose a mobility hazard. Similarly, the albedo of the site should not be particularly high, which would also suggest dusty surfaces. Low albedos are preferred, as they often coincide with low Viking red:violet ratios and indicate less dusty surfaces. Next, the Modeled Block Abundance should also not be too high or too low. Based on the Viking Lander and Mars Pathfinder experiences, percentages of blocks should be on the order of 5-25%. Too many blocks could pose a hazard to the landing and mobility. Too few blocks could also indicate a dusty surface. Primary Landing Site: Northern Meridiani Sinus (Proposed by T. J. Parker and K., S. Edgett) Vital Statistics: (1) Latitude, Longitude: 0-3 N, 350-2 W. *Elevation (Viking): about0.5-1.5 Ian. (2) Viking Orbiter Image coverage: Excellent coverage by 15 - 25 m/pixel images (orbits 709A and 410B). Possible stereo coverage in region where two orbits overlap (probably small parallax angle, as these orbits are not listed in NASA Contractor Report 3501) (3) Albedo: about .18 -.26 (4) Block Abundance: 5-26% (5)Fine-Component Thermal Inertia: 5-9 cgs units This region consists of bright deposits similar to those described by Edgett et al, that also lie within a prominent dark albedo region. These deposits are flat-lying, to such a degree that they ramp against topography rather than draping over it. This led Edgett and Parker to suggest that they may be subaqueous sediments, possibly lacustrine or marine evaporites, laid down sometime from the late Noachian to middle Hesperian (age determination pending crater counts). A contact between this material and elevated, dissected highlands to the south was identified , and is described by Edgett et al. Our desire in proposing this landing site is to sample the edge of this deposit where it has been exposed through etching, presumably eolian deflation (the deposit, though in the highlands, is itself only lightly to moderately cratered). This should enable access to in situ stratigraphy. The actual landing site will be selected where slopes are not expected to be steep, such that the rover itself should be able to traverse them and sample layered materials on the way, either up or down the slope. Perhaps due to uncertainties at this time as to the friability or meter-scale roughness of the deposit, it might make sense to place the landing ellipse on the exhumed highland surface adjacent to the deflated margin of the deposit and plan on driving to the deposit rather than landing on it and driving downslope. This should also enable imaging the margin for evidence of layering should it prove too difficult to climb. A target ellipse on the highland surface should also allow Athena access to ancient Noachian highland materials, particularly if placed near crater ejecta or an inlier of knobby material. Secondary Landing Site: Southern Elysium Planitia (Proposed by T. J. Parker) Vital Statistics: (1) Latitude, Longitude: 1.5-3.5 S, 195-198 W. (2) Elevation (Viking): -1.0 km. (3) Viking Orbiter Image coverage: Excellent coverage by 15 - 25 m/pixel images (orbit 725). Possible stereo coverage between images from beginning and end of orbit that overlap (probably small parallax angle) (4) Albedo: about .27-.28 (5) Block Abundance: 4-7% (6) Fine-Component Thermal Inertia: about 3 cgs units This region consists of eroded knobby material, probably of Noachian age, though much of the crater population has been destroyed, that is onlapped at a sharp contact by an extensive plains unit in southern Elysium Planitia that is Amazonian in age. The plains materials have been attributed to unusually low-viscosity flood lavas from fissures south of the Elysium volcanic rise, or to lacustrine materials associated with a large, Amazonian lake at the source of Marte Vallis. Parker and Schenk presented evidence in support of the latter interpretation, though they attributed the putative shore morphology to an embayment of a northern plains ocean into the southern Elysium region. Detailed examination of the margin of the deposit, showing erosion, not simply burial, of small crater rims and fluidized ejecta blankets, also points to lacustrine or marine sedimentation rather than volcanic plains burial. The plains surface exhibits a "crusty" appearance that many researchers have attributed to pressure ridges in lava flows. In a lacustrine context, they also resemble pressure ridges in desiccated evaporite deposits and salt-rimmed pools (now dry) similar in scale and morphology to spectacular, hundred meter-scale pool rims in alkaline Lake Natron, East African Rift. The eroded highland margin surface adjacent to these plains appears to be fairly smooth, even at 15 m/pixel. Isolated knob inliers are scattered from a few kilometers to several tens of "kilometers apart. Heights of the knobs have not been measured yet but, based on experience with similar features in the Pathfinder landing ellipse, are probably typically on the order of several tens of meters high and smaller, though some of the largest knobs in the region are probably up to a few hundred meters high. Two craters larger than a kilometer in diameter, with fluidized deposits, lie nearby the proposed landing site. Very high-resolution images from MOC should help to determine whether a landing site navigable by the Athena rover could be placed in this region. The space between knobs and craters is large enough to enable placement of a target landing ellipse between them but still provide access to one or more of them and to the margin of the Elysium plains material. Post-2001 Mars Surveyor Landing Site: Argyre Planitia (Proposed by T. J. Parker) Vital Statistics: (1) Latitude, Longitude: 55-56 S, 41-43 W. (2) Elevation (Viking): 1.0 km. (3) Viking Orbiter Image coverage: Excellent coverage by 40 m/pixel images (orbits 567B, 568B, and 569B). Excellent stereo coverage with large parallax angles over the entire landing site region, and much of central and southern Argyre. (4) Albedo: about .23-.24 (5) Block Abundance: No data (6) Fine-Component Thermal Inertia: No data The floors of both the Argyre and Hellas basins contain etched layered materials that are probably thick accumulations of channel or lacustrine sediments. The deposits in Hellas are much more eroded than those in Argyre, and Hellas lacks a channel outlet. Argyre is unique in that Uzboi Vallis flowed out of the basin, requiring overflow of a standing body of water within Argyre. This makes it the largest impact basin on Mars with channels both draining into it and flowing out from it. Hellas' channels may be catastrophic flood channels, whereas Argyre was fed by modest-scale valley networks, though the outlet at Uzboi Vallis was a catastrophic flood Highland craters and basins of this kind should be high-priority landing targets for missions intended to focus on the search for either prebiotic organic materials or even simple fossil microorganisms. Basins with internally-draining valley networks should be preferred over flood channels, as they could have provided the long-term influx of water favorable to the origin of life. (Catastrophic floods are not conducive to fossil preservation, due to their very short durations and high transportation energies). They also afford an opportunity to study the evolution of the planet's climate and volatiles during the period of time between the late Noachian and early Hesperian, when a drastic change from a proposed early warm, wet climate to one more closely resembling the modern environment is thought to have occurred. Large basin

Parker, T. J.↗