Influence of Charge Compensation on UV EXCITATION of Rare-Earth Fluorescence
Charge compensation defects influence on UV EXCITATION spectrum of rare earth doped crystals fluorescence
CRYSTAL STRUCTURE DEFECT↗
SEARCH · Search NASA
Results for “defect emission”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Low defect densities in molecular beam epitaxial GaAs achieved by isoelectronic In doping
A study has been made of the effects of adding small amounts of In (0.2-1.2 pct) to GaAs grown by molecular beam epitaxy. The density of four electron traps decreases in concentration by an order of magnitude, and the peak intensities of prominent emissions in the excitonic spectra are reduced with increase in In content. Based on the higher surface migration rate of In, compared to Ga, at the growth temperatures it is apparent that the traps and the excitonic transitions are related to point defects. This agrees with earlier observations by Briones and Collins (1982) and Skromme et al. (1985).
Bhattacharya, P. K.↗
The metal to metal interface and its effect on adhesion and friction
The paper considers the interface between two bulk metals and the effect of this interface on adhesive bonding, resistance to tangential displacements, friction and the interfacial transport from one surface to another. Using Auger emission spectroscopy, field ion microscopy, and low energy electron diffraction techniques, the influence of surface orientation, lattice registry, crystal lattice structure and defects, metal surface chemistry and alloying on the characteristics of the interface was studied for noble, platinum, transition, and Group 4B metals. With dissimilar metals in contact, epitaxial transfer of the cohesively weaker to the cohesively stronger metal has been observed. Surface chemical activity of the noble and platinum metals is shown to affect interfacial behavior as does a valence bonding in the transition metals, and the degree of metallic nature in the Group 4B elements. Alloying elements, e.g., Si and Fe, can alter interfacial behavior by segregation to the surface of metals or by altering bulk properties such as crystal transformation kinetics.
Buckley, D. H.↗
Thermal Inspection of Low Emissivity Surfaces Using a Pulsed Light Emitting Diodes (PLED) Heat Source
Thermal inspections of a structure typically utilize a flash or quartz lamp heat source located on the same side of an infrared camera. The heat source provides light energy for heating while the infrared camera measures the surface transient temperature response. The inspection can be difficult for low emissivity surfaces for several reasons. First, the high intensity light can reflect off the surface and cause “burn-in” to the camera’s detector. The “burn-in” can take time for the sensors to recover and potentially damage the detector. Secondly, the heat source after pulsing, has a transient cool down component. The cool down component can be reflected and therefore superimposed over the structure’s thermal response which can cause an error (false defect indications) in the inspection. Lastly, the heat source is spectrally broad and therefore while heating, infrared components of the heat source can produce non-uniformity in the measured temperature field. Typically for the inspection of reflective surfaces, paint or other emissivity enhancing coatings are applied before inspection. In this paper, a pulsed light emitting diodes (PLED) heat source is used. The PLED heat source is spectrally narrow, contained within the visible band, and therefore not detectable by the infrared camera. The PLED heat source is configured to reduce any transient cool down components that could produce false defect indications. The PLED thermal inspections are compared to commercially available flash thermography inspections on unpainted aluminum samples with simulated corrosion and additively manufactured Ti-6AL-4V metal specimens.
thermal nondestructive evaluation↗
Thermal Inspection of Low Emissivity Surfaces Using a Pulsed Light Emitting Diodes (PLED) Heat Source
Thermal inspections of a structure typically utilize a flash or quartz lamp heat source located on the same side of an infrared camera. The heat source provides light energy for heating while the infrared camera measures the surface transient temperature response. The inspection can be difficult for low emissivity surfaces for several reasons. First, the high intensity light can reflect off the surface and cause “burn-in” to the camera’s detector. The “burn-in” can take time for the sensors to recover and potentially damage the detector. Secondly, the heat source after pulsing, has a transient cool down component. The cool down component can be reflected and therefore superimposed over the structure’s thermal response which can cause an error (false defect indications) in the inspection. Lastly, the heat source is spectrally broad and therefore while heating, infrared components of the heat source can produce non-uniformity in the measured temperature field. Typically for the inspection of reflective surfaces, paint or other emissivity enhancing coatings are applied before inspection. In this paper, a pulsed light emitting diodes (PLED) heat source is used. The PLED heat source is spectrally narrow, contained within the visible band, and therefore not detectable by the infrared camera. The PLED heat source is configured to reduce any transient cool down components that could produce false defect indications. The PLED thermal inspections are compared to commercially available flash thermography inspections on unpainted aluminum samples with simulated corrosion and additively manufactured Ti-6AL-4V metal specimens.
thermal nondestructive evaluation↗
The SRB nozzle erosion related flow analysis
A study was performed to define the solid rocket booster (SRB) nozzle throat flow field, and to investigate one possible mechanism for the severe erosion which occurred on a recent flight. The flow field in the vicinity of the eroded area was not found to be exceptional, and the presence of a notch or scored area near the imbedded region nose did not appear to produce sufficient flow fluctuations to exacerbate the erosion characteristics of the throat liner. An interesting fluctuating mechanism was found in the imbedded cavity, but that mechanism (while of possible importance for erosion of the seal region) did not seem to adversely affect the region of concern. On the basis of this analysis, the conclusion can be drawn that the anomalous erosion did not result from a single mechanical defect (pit, or gouge) since the flow fluctuations which result seem insufficient to induce a repetitive pattern downstream. It further appears that the emission pattern exhibited did not result from a steady flow phenomena in the throat region. This does not rule out acoustic phenomena or severe start-up transients.
Prozan, R. J.↗
Acousto-ultrasonics - Retrospective exhortation with bibliography
Major research on the acousto-ultrasonic (AU) technique (also known as the stress-wave-factor technique) encompassing aspects of acoustic emission and ultrasonic materials characterization methodology is reviewed. AU deals primarily with such factors as the assessment of the integrated effects of diffuse defect states, thermomechanical degradation, and population of subcritical flaws that influence AU measurements correlating with mechanical property variations. AU is used to evaluate fiber-reinforced composites, adhesive bonds, lumber, paper and wood products, cable and rope, and human bone. The AU technique has been demonstrated to be sensitive to interlaminar and adhesive bond strength variations and has been shown to be useful in assessing microporosity and microcracking produced by fatigue cycling. An extensive bibliography ranging from 1985 to 1991 is presented.
Vary, Alex↗
Furnace Cyclic Oxidation Behavior of Multi-Component Low Conductivity Thermal Barrier Coatings
Ceramic thermal barrier coatings will play an increasingly important role in advanced gas turbine engines because of their ability to further increase engine operating temperatures and reduce cooling, thus helping achieve future engine low emission, high efficiency and improved reliability goals. Advanced multi-component zirconia-based thermal barrier coatings are being developed using an oxide defect clustering design approach to achieve the required coating low thermal conductivity and high temperature stability. Although the new composition coatings were not yet optimized for cyclic durability, an initial durability screening of the candidate coating materials was conducted using conventional furnace cyclic oxidation tests. In this paper, furnace cyclic oxidation behavior of plasma-sprayed zirconia-based defect cluster thermal barrier coatings was investigated at 1163 C using 45 min hot cycles. The ceramic coating failure mechanisms were studied using scanning electron microscopy (SEM) combined with X-ray diffraction (XRD) phase analysis after the furnace tests. The coating cyclic lifetime is also discussed in relation to coating processing, phase structures, dopant concentration, and other thermo-physical properties.
Zhu, Dong-Ming↗
Point Defect Distributions in ZnSe Crystals: Effects of Gravity Vector Orientation during Physical Vapor Transport Growth
ZnSe crystals were grown by the physical vapor transport technique under horizontal and vertical (stabilized and destabilized) configurations. Secondary ion mass spectroscopy and photoluminescence measurements were performed on the ZnSe samples to map the distributions of [Si], [Fe], [Cu], [Al] and [Li or Na] impurities as well as Zn vacancy, [V(zn)]. The annealings of ZnSe under controlled Zn pressures were studied to correlate the measured photoluminescence emission intensity to the equilibrium Zn partial pressure. In the horizontal grown crystals the segregations of [Si], [Fe], [Al] and [V(zn)] along the gravity vector direction were observed whereas in the vertically stabilized grown crystal the segregations of these point defects were radially symmetrical. No apparent pattern was observed on the measured distributions in the vertically destabilized grown crystal. The observed segregations in the three growth configurations were interpreted based on the possible buoyancy-driven convection in the vapor phase.
Su, Ching-Hua↗
Improved Model for MOS Breakdown
With an improved model, accelerated high-field tests can be used to predict gate-oxide breakdown in metal-oxide-semi-conductor (MOS) structures. Principal mechanism in MOS breakdown is mobile-ion emission from metal/oxide interface, which occurs during application of positive gate-bias field. Breakdown is related to clustering of emitted ions at localized defect sites in oxide/silicon interface. Using new model to interpret data, tests that normally take several weeks at low fields to accumulate sufficient statistics can be completed in only a few hours at high fields.
Li, S. P.↗
Point Defect Distributions in ZnSe Crystals: Effects of Gravity Vector Orientation During Physical Vapor Transport Growth
ZnSe crystals were grown by the physical vapor transport technique under horizontal and vertical (stabilized and destabilized) configurations. Secondary ion mass spectroscopy and photoluminescence measurements were performed on the grown ZnSe samples to map the distributions of [Si], [Fe], [Cu], [Al] and [Li or Na] impurities as well as Zn vacancy, [V (sub Zn)]. Annealings of ZnSe under controlled Zn pressures were studied to correlate the measured photoluminescence emission intensity to the equilibrium Zn partial pressure. In the horizontal grown crystals the segregations of [Si], [Fe], [Al] and [V (sub Zn)] were observed along the gravity vector direction whereas in the vertically stabilized grown crystal the segregation of these point defects was radially symmetrical. No apparent pattern was observed on the measured distributions in the vertically destabilized grown crystal. The observed segregations in the three growth configurations were interpreted based on the possible buoyancy-driven convection in the vapor phase.
Su, Ching-Hua↗
A quantitative method for photovoltaic encapsulation system optimization
It is pointed out that the design of encapsulation systems for flat plate photovoltaic modules requires the fulfillment of conflicting design requirements. An investigation was conducted with the objective to find an approach which will make it possible to determine a system with optimum characteristics. The results of the thermal, optical, structural, and electrical isolation analyses performed in the investigation indicate the major factors in the design of terrestrial photovoltaic modules. For defect-free materials, minimum encapsulation thicknesses are determined primarily by structural considerations. Cell temperature is not strongly affected by encapsulant thickness or thermal conductivity. The emissivity of module surfaces exerts a significant influence on cell temperature. Encapsulants should be elastomeric, and ribs are required on substrate modules. Aluminum is unsuitable as a substrate material. Antireflection coating is required on cell surfaces.
Garcia, A., III↗
Review of acousto-ultrasonic NDE for composites
Acousto-ultrasonics utilizes simulated stress waves to detect and quantify defect states, damage conditions, and variations of mechanical properties in fiber reinforced composites. The term acousto-ultrasonics denotes a combination of aspects of acoustic emission methodology with ultrasonic materials characterization. The acousto-ultrasonic approach was developed to deal primarily with evaluation of the integrated effect of minor flaws and diffuse flaw populations of subcritical flaws in composite and bonded structures. These factors singly and collectively also influence acousto-ultrasonic measurements that, in turn, correlate with dynamic response and mechanical property variations. Since it was first introduced, the acousto-ultrasonic approach was successfully applied to a variety of materials, including polymeric, metallic, and ceramic matrix composites; adhesively bonded materials; paper and wood products; cable and rope; and also human bone. Examples of applications and limitations of the approach are reviewed. Basic methods and guidelines are discussed. The underlying hypothesis and theory development needs are indicated.
Vary, Alex↗
Effects of moisture in infrared thermography of resin matrix composites
Several multiply graphite polyimide composite specimens were examined by real-time infrared thermography in order to study the effects of moisture on their thermograms. Heat was injected from one side and IR emission detected on the opposite side using AGA Thermovision System-680. No differences between the thermograms of dry and water containing specimens were detected for defect-free specimens. However, the presence of trapped water in defective specimens modified the thermographic contrast significantly. It is concluded that: (1) IR thermography can be used to detect moisture in defective composites, and (2) because of the possibility of moisture camouflaging defects, IR thermography for subsurface defect detection should be supplemented by other techniques - such as acoustical imaging and X-radiography.
Singh, J. J.↗
Experimental Observations of Damage States in Unnotched and Notched 3D Orthogonal Woven Coupons Loaded in Tension
This paper describes a series of unnotched and notched tensile tests on two 3D orthogonal woven architectures. Dog bone specimens were used for the unnotched tests, and open-hole specimens were used for the notched tests. For each architecture and test type, two specimens were loaded under monotonic displacement control to failure and two specimens were incrementally loaded to failure in five steps. X-ray computed tomography (CT) was used to characterize the woven architecture and defects on each specimen prior to testing. Digital image correlation (DIC) images were obtained from both sides of the specimen throughout the loading and unloading. Acoustic emission (AE) data were also continuously acquired throughout the loading. For the incremental tests, X-ray CT was used to document the damage progression after each load increment. The damage progression was analyzed based on the results from these three techniques. The results for both architectures and test specimens followed a pattern where matrix cracks formed at the surface perpendicular to the tensile load direction. New surface cracks formed continuously throughout the loading and cracks extended in depth and width. In general, fiber failure was not detected until specimen failure.
Wade C Jackson↗
Advanced Low Conductivity Thermal Barrier Coatings: Performance and Future Directions (Invited paper)
Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. In this presentation, thermal barrier coating development considerations and performance will be emphasized. Advanced thermal barrier coatings have been developed using a multi-component defect clustering approach, and shown to have improved thermal stability and lower conductivity. The coating systems have been demonstrated for high temperature combustor applications. For thermal barrier coatings designed for turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability. Erosion resistant thermal barrier coatings are being developed, with a current emphasis on the toughness improvements using a combined rare earth- and transition metal-oxide doping approach. The performance of the toughened thermal barrier coatings has been evaluated in burner rig and laser heat-flux rig simulated engine erosion and thermal gradient environments. The results have shown that the coating composition optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic durability. The erosion, impact and high heat-flux damage mechanisms of the thermal barrier coatings will also be described.
Zhu, Dongming↗
Advanced Low Conductivity Thermal Barrier Coatings: Performance and Future Directions
Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. In this presentation, thermal barrier coating development considerations and performance will be emphasized. Advanced thermal barrier coatings have been developed using a multi-component defect clustering approach, and shown to have improved thermal stability and lower conductivity. The coating systems have been demonstrated for high temperature combustor applications. For thermal barrier coatings designed for turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability. Erosion resistant thermal barrier coatings are being developed, with a current emphasis on the toughness improvements using a combined rare earth- and transition metal-oxide doping approach. The performance of the toughened thermal barrier coatings has been evaluated in burner rig and laser heat-flux rig simulated engine erosion and thermal gradient environments. The results have shown that the coating composition optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic durability. The erosion, impact and high heat-flux damage mechanisms of the thermal barrier coatings will also be described.
Zhu, Dongming↗
Development and Characterization of Lightweight Durable Composite Conductor for Cables
Sustainable aviation in the form of electrified propulsion is likely to lead to an increase in the electrical assets contained within a single aircraft. As a result, it is desirable to design light weight conductor materials, thus reducing the payload of components like motor windings, low voltage signal cables, and transmission cables for data and power. One approach involves replacing pure Cu wiring with metalized CNT composites. This paper evaluates a framework for modeling overall conductivity and current sharing within such composites. Processing methods and parameters were refined. Select electroplated samples outperformed pure Cu in conductivity and had comparable ultimate tensile strengths. Tensile strengths are expected to improve with an additional densification step during processing. Acoustic emission data was used to predict the failure mechanism of the composite. Theories explaining improved intrinsic conductivity are discussed, with a focus on chemical and mechanical interactions at the Cu-CNT interface. These include Cu infiltration of CNT crevices, CNT oxidation, activity at defects in CNT walls, and the release of carbide-forming metals from CNT walls. Validating any or all these theories will require further work replicating data, collecting electron micrographs and conducting chemical analyses.
Metalized CNT↗