Search NASA⌕ Search

SEARCH · Search NASA

Results for “defect size distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Tuning gas separation performance of polyimide membranes with macrocyclic crown ether units

Membrane-based gas separation is an energy-efficient alternative to conventional thermally-driven separation processes. However, polymer membranes face the permeability-selectivity trade-off challenge, which stems from the broad size distribution of free volume voids. Here, this study reports a molecular design strategy to address this challenge through incorporating macrocyclic crown ether (CE) moieties into the backbone of Matrimid® polyimide, a commercial gas separation membrane. A series of CE-containing Matrimid®-like copolyimides were synthesized with systematically varied CE molar contents ranging from 3 to 20%. These copolyimides formed ductile, defect-free thin films suitable for membrane fabrication. Gas permeation tests revealed a non-monotonic relationship between permeability/selectivity and CE content. Notably, the copolyimide with only 5% CE demonstrated a 61% increase in CO 2 /CH 4 selectivity and a 13% increase in CO 2 permeability relative to pristine Matrimid®. Higher CE contents did not yield further performance improvements, which is likely due to the competing effects of chain packing disruption and π–π interactions among CE moieties at high content. This hypothesis was supported by wide-angle X-ray scattering (WAXS) analysis, density measurements, and fractional free volume calculations. These findings highlight the potential of macrocyclic crown ether incorporation strategies in fine tuning the microstructure of commercial polyimide gas separation membranes to surpass the traditional permeability-selectivity trade-off.

CO2 separation↗
NASA NTRS1989

Microparticle impacts in space: Results from Solar Max and shuttle witness plate inspections

The Solar Maximum Satellite developed electronic problems after operating successfully in space for several years. Astronauts on Space Shuttle mission STS-41C retrieved the satellite into the orbiter cargo bay, replaced defective components, and re-deployed the repaired satellite into orbit. The defective components were returned to Earth for study. The space-exposed surfaces were examined. The approach and objectives were to: document morphology of impact; find and analyze projectile residue; classify impact by origin; determine flux distribution; and determine implications for space exposure. The purpose of the shuttle witness plate experiment was to detect impacts from PAM D2 solid rocket motor; determine flux and size distribution of particles; and determine abrasion effects on various conditions. Results are given for aluminum surfaces, copper surfaces, stainless steel surfaces, Inconel surfaces, and quartz glass surfaces.

Mckay, David S.↗
DOE OSTI2025

Nanoscale Strain and Octahedral Tilting Removes Structural and Nonradiative Defects in 2D-Templated FAPbI 3

The halide perovskite formamidinium lead iodide (FAPbI 3 ) is a prime candidate for photovoltaics due to its excellent optoelectronic properties, but its application has been limited due to its structural instability. The large size of the FA cation results in metastability of the photoactive cubic phase and a facile degradation into thermodynamically stable hexagonal phases at room temperature. Recently, the incorporation of two-dimensional (2D) Ruddlesden-Popper halide perovskite seeds into a FAPbI 3 precursor solution was shown to template the growth of and stabilize cubic FAPbI 3 . Here, in this study, we investigate the nanoscale structural and optoelectronic mechanisms behind the observed bulk stabilization using synchrotron-based X-ray microscopies. Nanoprobe X-ray diffraction reveals 2D-templated FAPbI 3 films exhibit an average compressive strain normal to the substrate of -3.3%, 2-fold larger than that of MACl-stabilized FAPbI 3 . This compression creates locally templated regions composed of tetragonal-phase FAPbI 3 distributed nonuniformly throughout the film with fewer crystalline defects than purely cubic regions. Scanning X-ray excited optical luminescence (X-ray analog of photoluminescence) reveals that this local templating results in increased radiative recombination and red-shifted band edge and emission. Our results provide insight into the microscopic mechanism for the phase stabilization of FAPbI 3 using 2D perovskites as templates.

X-ray diffraction↗
NASA NTRSDate not supplied

An Electron Backscatter Diffraction (EBSD)-Based Automated Tool for Ceramic Capacitor Grain Size Analysis

Ceramic capacitors continue to be recurring problem parts for NASA, despite best efforts to screen out potential defects and failures through environmental and electrical testing and nondestructive inspection techniques such as acoustic microscopy. The physical properties of ceramic capacitors necessitates thin dielectric layers capable of withstanding significant electric fields. Any defects in those ceramic layers can result in reduced insulation resistance failure modes including short circuit failures, so the quality and consistency of the dielectric material is critical. The size of the individual ceramic grains in the dielectric material is a critical parameter. However, judging “grain size” is not so simple—in a single capacitor there can be wide variation in grain sizes observed. It is theorized that by studying the grain size distributions of “known good” and “known bad” lots of capacitors, some conclusions could be drawn that would allow us to better predict to the reliability of future lots based on grain size distributions. The initial goal of this effort was to find or develop an automated tool that could inspect a capacitor and return grain size distribution results.

Robert Hodson↗
NASA NTRS2000

Structural Characterization of Crystalline Ice Nanoclusters

Water ice nanoclusters are useful analogs for studying a variety of processes that occur within icy grains in the extraterrestrial environment. The surface of ice nanoclusters prepared in the laboratory is similar to the surface of interstellar ice grains. In cold molecular clouds, the silicate cores of interstellar grains are typically approx. 100 nm in diameter and have a coating of impure amorphous water ice. Depositional, thermal and radiolytic processes leave the surface and subsurface molecules in a disordered state. In this state, structural defects become mobile and reactions of trapped gases and small molecules can occur. The large surface area of nanocluster deposits relative to their bulk allows for routine observation of such surface-mediated processes. Furthermore, the disordered surface and subsurface layers in nanocluster deposits mimic the structure of amorphous ice rinds found on interstellar dust grains. Transmission Electron Microscopy (TEM has been used tn characterize the crystallinity, growth mechanism, and size distribution of nanoclusters formed from a mixture of water vapor with an inert carrier gas that has been rapidly cooled to 77K. E M imaging reveals a Gaussian size distribution around a modal diameter that increases from approx. 15 to 30 nm as the percentage of water vapor within the mixture increases from 0.5 to 2.007, respectively . TEM bright and dark field imaging also reveals the crystalline nature of the clusters. h4any of the clusters show a mosaic structure in which crystalline domains originate at the center Other images show mirror planes that are separated by approx. 10 nm. Electron diffraction patterns of these clusters show that the clusters are composed of cubic ice with only a small hexagonal component. Further, the crystalline domain size is approximately the same as the modal diameter suggesting that the clusters are single crystals.

Blake, David↗
NASA NTRS1986

Effects of macroscopic inhomogeneities on electron mobility in semi-insulating GaAs

It is shown that defect inhomogeneities of sizes larger than the electron mean free path are responsible for the low values and anomalous temperature dependence of the electron mobility in semi-insulating (SI) GaAs. The room-temperature electron mobility values below about 6000 sq cm/V s cannot be uniquely used for the determination of the concentration of ionized defects, since the contribution from inhomogeneities usually exceeds that from scattering by ionized impurities. The effects of the macroscopically inhomogeneous distribution of residual acceptors and the major deep donor EL2 diminish at elevated temperatures between 600 and 900 K, which offers a means for identification of inhomogeneities, and furthermore explains recently reported steplike mobility versus temperature behavior in SI-GaAs.

Walukiewicz, W.↗
DOE OSTI2025

Scalable Bottom-Up Synthesis of Nanoporous Hexagonal Boron Nitride ( h -BN) for Large-Area Atomically Thin Ceramic Membranes

Nanopores embedded within monolayer hexagonal boron nitride (h-BN) offer possibilities of creating atomically thin ceramic membranes with unique combinations of high permeance (atomic thinness), high selectivity (via molecular sieving), increased thermal stability, and superior chemical resistance. However, fabricating size-selective nanopores in monolayer h-BN via scalable top-down processes remains nontrivial due to its chemical inertness, and characterizing nanopore size distribution over a large area remains extremely challenging. Here, we demonstrate a facile and scalable approach of exploiting the chemical vapor deposition (CVD) process temperature to enable direct incorporation of subnanometer/nanoscale pores into the monolayer h-BN lattice, in combination with manufacturing compatible polymer casting to fabricate centimeter-scale nanoporous atomically thin ceramic membranes. We leverage diffusive transport of analytes including size-selective Ficoll sieving to characterize subnanometer-scale and nanoscale defects that manifest as pores in centimeter-scale h-BN membranes, overcoming previous limitations in large-area characterization of nanoscale defects in h-BN. Our approach opens a new frontier to advance atomically thin membranes to 2D ceramic materials, such as h-BN via facile and direct formation of nanopores, for size-selective separations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Unveiling Structural Heterogeneity and Imbalance of Gold Decahedral Nanoparticles using Four-dimensional Scanning Transmission Electron Microscopy

Multi-twinned structures have been observed in technologically important crystal systems, for example diamond cubic and face-centered cubic (FCC) lattices, that include materials such as diamond, silicon, a wide range of noble metals, and their nanoscale counterparts. Beyond atomic building blocks, the special arrangements also occur in the self-assembly of nanoparticles (NP) and μm-sized colloidal particles and occupy parts of their phase diagrams. Spanning a wide range of length scales, the universality of the structures arises when the systems attempt to achieve multitwinned structures by overcoming geometric misfits during minimizing surface energies with entirely {111} or close-packing facets. While it is fundamental to understand how strain is sustained upon twinned structures and symmetry breaking, the knowledge will be paramount in practical aspects such as guiding and controlling the thin film growth, anisotropic NP growth, and self-assembly of NPs. Au decahedral (Dh) NP, as the most prevalent multi-twinned model system, fits five tetrahedral motifs into a circle by sharing an axis resulting in a geometric misfit angle of 7.35°, or a disclination with power of -7.35°. Postulating how Au FCC lattice adopts the misfit, theoretical models have been developed to address the underlying lattice symmetry and inhomogeneous strain distribution separately. Yet, experimental reports regarding the former have been limited due to the relatively large X-ray beam sizes that do not fit the sizes of NPs. On the other hand, though the latter has been widely adapted in the thermodynamics of small (<10 nm) multi-twinned nanoparticles, previous literature has shown that, at edge length of 17 nm, the theory’s is invalidated by shear strain that is observed in a defect-free Au Dh NP by high-resolution transmission electron microscopy (HR-TEM) imaging. Though the advancement of aberrationcorrected scanning transmission electron microscopy (AC-STEM) imaging and ab initio calculation techniques brings new opportunities, along with challenges in complicated image analysis and limitation in particle size (usually below 10 nm), the gap between nanoscale and mesoscale has never been extended to gain insight from atomic system with straightforward interaction potentials.

4D-STEM↗
DOE OSTI2025

Editorial: Functionalization of porous materials for sustainable energy applications

Global energy demands are shifting toward a more sustainable future, with the goal of achieving carbon neutrality by 2050. Emerging technologies are driving this transition. The industry, academia, government, non-profit organizations, and the broader community are collaboratively working to reduce greenhouse gas (GHG) emissions and address climate change to ensure a sustainable future. According to the International Energy Agency, in 2022, the production, transportation, and processing of oil and gas resulted in 5.1 billion tons of CO 2 -equivalent emissions, representing nearly 15% of all energy-related GHG emissions. Moreover, the end-use of oil and gas accounted for an additional 40% of emissions. The IEA’s Net Zero Emissions by 2050 Scenario calls for immediate, collective action from the industry, transportation and other stakeholders to mitigate these emissions. In this effort, the development of energy materials will play a critical role in reducing emissions. Among these, porous materials offer an innovative solution, leveraging their high surface area, adjustable pore sizes, and chemical versatility to address these pressing challenges effectively. By carefully designing their nanostructures, the architecture and properties of these materials can be tailored for specific applications. Key factors such as chemical composition, particle size, pore distribution, and surface area optimization enhance the reactivity and energy conversion efficiency. Additionally, pre- and post-functionalization processes can introduce targeted chemical properties, further improving their performance. This Research Topic explores recent advancements in energy and materials science through four scholarly papers, showcasing innovative solutions for sustainable energy technologies while providing valuable insights into the unique properties and structure of porous materials (Figure 1). Li et al. present their work on highly defective NiFeV layered triple hydroxides, highlighting enhanced electrocatalytic activity and stability for oxygen evolution reactions (OER). Kovalskii et al. contribute a mini-review on hydrogen storage using hexagonal boron nitride (h-BN) and BN-based materials, offering an insightful overview of these promising materials. Chava et al. discuss their recent achievements in ceramic electrolytes used for improvement of performance of solid-state batteries. Lastly, Li et al. review the properties of porous materials with a focus on shrinkage behavior during the drying process, shedding light on key considerations for material design.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Algorithms for coordinate reconstruction in position-sensitive virtual Frisch-grid detectors

Arrays of position-sensitive virtual Frisch-grid (VFG) CdZnTe (CZT) detectors provide a cost-effective solution for integrating large-area arrays for gamma-ray imaging and spectroscopy. These detectors employ high-aspect ratio CZT crystals (bars) with thicknesses up to 50 mm and cross-sections of up to 10 × 10 mm 2 . Despite the long drift distances of charge carriers in such crystals, the detectors have demonstrated excellent performance, achieving energy resolutions better than 1 % full width at half maximum (FWHM) at 662 keV and 3D position resolutions finer than 1 mm. The high spatial resolution is a critical feature of these detectors, as it enables correction of response non-uniformities caused by crystal defects, which remain present even in the highest-quality CZT material. Dislocations and dislocation walls are the primary defects responsible for variations in charge carrier losses as they drift from the interaction points toward the charge-collecting electrodes. The mechanism by which these defects affect carrier transport is generally well understood. Dislocations and sub-grain boundaries act as sinks for carrier-trapping centers, primarily impurities and secondary phases such as tellurium inclusions and precipitates. Here, these regions exhibit significantly higher carrier-trapping rates, leading to variations in the μτ-products. Because the locations of these micron-sized regions are fixed within the detector volume, fluctuations in the total collected charge arise from the random distribution of interaction sites. This results in non-uniform detector responses and degradation of energy resolution. However, by measuring the interaction-site locations with sufficient precision, charge-loss variations can be accurately corrected, allowing recovery of nearly intrinsic energy resolution.

47 OTHER INSTRUMENTATION↗
NASA NTRS1998

Microstructural, Chemical and Mechanical Characterization of Polymer-Derived Hi-Nicalon Fibers with Surface Coatings

Room temperature tensile strengths of as-received Hi-Nicalon fibers and those having BN/SiC, p-BN/SiC, and p-B(Si)N/SiC surface coatings, deposited by chemical vapor deposition, were measured using an average fiber diameter of 13.5 microns. The Weibull statistical parameters were determined for each fiber. The average tensile strength of uncoated Hi-Nicalon on was 3.19 +/- 0.73 GPa with a Weibull modulus of 5.41. Strength of fibers coated with BN/SiC did not change. However, coat with p-BN/SiC and p-B(Si)N/SiC surface layers showed strength loss of approx. 10 and 35 percent, respectively, compared with as-received fibers. The elemental compositions of the fibers and the coatings were analyzed using scanning Auger microprobe and energy dispersive x-ray spectroscopy. The BN coating was contaminated with a large concentration of carbon and some oxygen. In contrast, p-BN, p-B(Si)N, and SiC coatings did not show any contamination. Microstructural analyses of the fibers and the coatings were done by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and selected area electron diffraction. Hi-Nicalon fiber consists of the P-SIC nanocrystals ranging in size from 1 to 30 nm embedded in an amorphous matrix. TEM analysis of the BN coating revealed four distinct layers with turbostatic structure. The p-BN layer was turbostratic and showed considerable preferred orientation. The p-B(Si)N was glassy and the silicon and boron were uniformly distributed. The silicon carbide coating was polycrystalline with a columnar structure along the growth direction. The p-B(Si)N/SiC coatings were more uniform, less defective and of better quality than the BN/SiC or the p-BN/SiC coatings.

Bansal, Narottam P.↗
DOE OSTI2025

Role of Computational Parameters on Predicting Self-Consistent Residual Stress and Distortion during Wire Arc Additive Manufacturing

Production of three-dimensional metallic parts through integration of an articulated robot and gas metal arc welding, also known as wire arc additive manufacturing (WAAM), can produce large-scale components with moderate geometrical complexity. This technology is particularly appealing due to its high deposition rates, scalability, and cost-effective feedstock compared to other AM processes. Despite its advantages, WAAM adoption is hindered by challenges in ensuring geometric conformity without extensive distortion, defect-free structures, and consistent mechanical properties. Finite element analysis (FEA) is often used to address the challenge of geometrical conformity. As the size of parts increases, the best practices for mesh size and temporal resolution known in the literature become computationally unviable. This research examined the effects of mesh and time-step resolutions during transient FEA of a large-scale (248 layers) metallic part. The impact of computational parameters on the thermal history, displacement, and residual stress distributions were evaluated. The results showed that predicted distortion was consistent across resolutions, while time-step length significantly affected predicted thermal history, and mesh size influenced residual stress distributions. To investigate this relationship further, directionally biased meshes were considered and analyzed. The results indicated that increasing mesh resolution perpendicular to the welding path yielded stress predictions that aligned closely with higher-resolution models while offering substantial computational savings. In conclusion, the significances of this research are related to verification and validation of WAAM models for widespread industrial adoption and pragmatic guidelines for optimizing computation parameters for balancing computational efficiency and predictive accuracy of residual stress and distortion.

Solsbee, Brandon [Univ. of Tennessee, Knoxville, T↗
NASA NTRS1997

Theoretical and Experimental Evaluation of the Bond Strength Under Peeling Loads

Reliable applications of adhesively bonded joints require understanding of the stress distribution along the bond-line and the stresses that are responsible for the joint failure. To properly evaluate factors affecting peel strength, effects of defects such as voids on the stress distribution in the overlap region must be understood. In this work, the peel stress distribution in a single lap joint is derived using a strength of materials approach. The bonded joint is modeled as Euler-Bernoulli beams, bonded together with an adhesive. which is modeled as an elastic foundation which can resist both peel and shear stresses. It is found that for certain adhesive and adherend geometries and properties, a central void with the size up to 50 percent of the overlap length has negligible effect on the peak peel and shear stresses. To verify the solutions obtained from the model, the problem is solved again by using the finite element method and by treating the adherends and the adhesive as elastic materials. It is found that the model used in the analysis not only predicts the correct trend for the peel stress distribution but also gives rather surprisingly close results to that of the finite element analysis. It is also found that both shear and peel stresses can be responsible for the joint performance and when a void is introduced, both of these stresses can contribute to the joint failure as the void size increases. Acoustic emission (AE) activities of aluminum-adhesive-aluminum specimens with different void sizes were monitored. The AE ringdown counts and energy were very sensitive and decreased significantly with the void size. It was observed that the AE events were shifting towards the edge of the overlap where the maximum peeling and shearing stresses were occurring as the void size increased.

Nayeb-Hashemi, Hamid↗
DOE OSTI2026

Time at Temperature Experiments on Neutron Irradiated Zircaloy-2 using Conventional & Flash DSC

Dryout events in Boiling Water Reactors (BWRs) are currently treated by NRC regulations as automatic disqualification for continued fuel rod operation, even though this criterion does not account for the rate or duration of power increases, associated changes in material behavior, or the possibility of rewetting. Operational history from Anticipated Operational Occurrences (AOOs) shows that short, transient power excursions often demand only modest heat removal, and industry experience suggests that fuel can briefly enter dryout yet return to safe, stable operation. The lack of detailed understanding of the material response during such events motivates the present series of experiments. This study uses unique and innovative methods to investigate microstructural evolution in irradiated Zircaloy-2 exposed to high temperatures in inert environments. Differential Scanning Calorimetry (DSC) and FlashDSC are combined to build a comprehensive experimental framework capable of identifying the a–ß phase transformation in zirconium and examining defect annealing under steep thermal gradients. FlashDSC enables rapid heating and cooling of Focused Ion Beam (FIB)–prepared large-area lift-outs (LALOs) of irradiated Zircaloy-2 at rates of 1,000 K/s to peak temperatures of 600°C, 750°C, and 900°C. The goal is to determine whether these conditions produce measurable microstructural changes that could influence cladding performance in typical BWR environments. Microstructural characterization includes quantifying dislocation density and assessing secondary phase particle (SPP) size and distribution using Transmission Electron Microscopy (TEM). Ongoing analysis, such as diffraction pattern indexing and 4D STEM processing, will further refine these observations.

36 - MATERIALS SCIENCE↗
NASA NTRS1994

Computation of turbulent boundary layers employing the defect wall-function method

In order to decrease overall computational time requirements of spatially-marching parabolized Navier-Stokes finite-difference computer code when applied to turbulent fluid flow, a wall-function methodology, originally proposed by R. Barnwell, was implemented. This numerical effort increases computational speed and calculates reasonably accurate wall shear stress spatial distributions and boundary-layer profiles. Since the wall shear stress is analytically determined from the wall-function model, the computational grid near the wall is not required to spatially resolve the laminar-viscous sublayer. Consequently, a substantially increased computational integration step size is achieved resulting in a considerable decrease in net computational time. This wall-function technique is demonstrated for adiabatic flat plate test cases from Mach 2 to Mach 8. These test cases are analytically verified employing: (1) Eckert reference method solutions, (2) experimental turbulent boundary-layer data of Mabey, and (3) finite-difference computational code solutions with fully resolved laminar-viscous sublayers. Additionally, results have been obtained for two pressure-gradient cases: (1) an adiabatic expansion corner and (2) an adiabatic compression corner.

Brown, Douglas L.↗
DOE OSTI2025

From Structure to Function: Zn/Mn-Modified Maghemite as an Advanced Nanoplatform for Magnetic Hyperthermia and Radionuclide Therapy

The development of nanoplatforms capable of efficient heat generation and stable radionuclide delivery is essential for effective bimodal cancer therapy. Here, in this study, binary (Fe–M) and ternary (Fe–M–M′) metal oxide nanoparticles were synthesized via a polyol method optimized to produce flower-like γ-Fe 2 O 3 (maghemite) structures, with M and M′ representing Zn and/or Mn. Comprehensive structural and magnetic characterization was conducted to explain the relationship between composition, defect structure, and hyperthermic performance. The analyses revealed that cation substitution induced an Fe-site vacancy, primarily at octahedral positions, leading to local structural distortions, as confirmed by powder X-ray diffraction and pair distribution function analysis. The optimized composition, with Zn/Mn/Fe = 0.040:0.182:1, exhibited the highest concentration of vacancies and structural disorder. These vacancies altered the bonding environment, enhancing magnetic interactions at tetrahedral sites while weakening those at the octahedral positions. The resulting multicore nanoflowers (20–63 nm; core size 13–18 nm) displayed strong heating performance, with intrinsic loss power ranging from 0.34 to 5.77 nHm 2 kg –1 . The optimized sample achieved a temperature increase of 30 °C within 2 min and a specific absorption rate of 369 W g –1 . This composition was further coated with citrate (CA) and successfully radiolabeled with 177 Lu, achieving a radiolabeling yield of 92.7% and excellent stability, thus forming a robust nanoplatform for combined magnetic hyperthermia and radionuclide therapy. Biological evaluation of the optimized S5 composition revealed selective cytotoxicity toward HeLa and LS174 cells, while toxicity was significantly lower to A549, A375, and normal MRC-5 cells. Citrate coating of S5 nanoparticles (S5@CA) drastically reduced their cytotoxicity across all tested cell lines (IC 50 > 200 μg mL –1 ), confirming their enhanced biocompatibility for therapeutic applications. In HeLa cells subjected to magnetic hyperthermia, the viability decreased to approximately 84% after 30 min and 61% after 60 min of treatment, demonstrating the sustained hyperthermic effect at a controlled working temperature of 48 °C. These results underscore the effectiveness of cation substitution and vacancy engineering in tailoring the functional properties of maghemite-based nanomaterials for advanced multimodal cancer therapies.

36 MATERIALS SCIENCE↗
NASA NTRSDate not supplied

Investigation of the Effect of Etch Pits on the Material Properties of Carbon Fiber Structures

It is well known that etch pits are formed on carbon surfaces during their consumption in reactive gas environments such as during ablation of carbon-based thermal protection system (TPS) materials. These pits start out from atomic defects on the carbon surface, grow in size and then ultimately lead to the complete removal of the solid carbon material. However, the effect of such etch pits on the material properties of carbon ablators such as FiberForm are poorly understood, as the maximum size of pits are on the order of microns in size, which makes them hard to observe experimentally. Hence, we have developed a module within the Porous Microstructure Analysis code PuMA that can generate etch pits on an arbitrary material surface, with a prescribed distribution of pit size and density. We use this newly developed module to calculate material properties of FiberForm, which is the base material for one of the most commonly used TPS materials - Phenolic Impregnated Carbon Ablator (PICA). The detailed microstructure of FiberForm in PuMA will either be generated synthetically or obtained from X-ray microtomography. Our simulations show that material properties such as the thermal conductivity and tortuosity decrease with increasing degree of pitting. This will be helpful to more accurately predict the degradation of carbon-based TPS during ablation, and furthermore may allow us to identify previously unknown TPS failure modes due to pitting.

PuMA↗