Search NASASearch

SEARCH · Search NASA

Results for “design of computer experiments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

A simulation-based fault injection experiment to evaluate self-test diagnostics for a fault-tolerant computer

The design and results of a fault injection experiment conducted in the Airlab facility at NASA-Langley using a logic network simulator are described. An attempt was made to determine the effectiveness of the diagnostic self-test sequences used to detect failures in the communicator/interstage (C/I) of a fault-tolerant processor (FTP). Identification of the undetected faults in the C/I Status Register logic resulted in changes in the diagnostic test sequences implemented for the FTP.

Baker, Robert L.

Contribution of Lobe Power to Experiment Heating in the Advanced Test Reactor

In order to ease the computational burden associated with designing irradiation experiments in the Advanced Test Reactor (ATR), scaling factors are often used to estimate design parameters at different lobe powers. Here, this paper examines the validity of long-standing assumptions about the contribution of lobe power to total experiment heating in the ATR. For each of the ATR’s 77 different experiment positions, the fractional contribution of each of the ATR’s five lobes to the total heating in that position is calculated and compared to traditional assumptions. The updated fractional contributions are then used to scale heating rates in a sample problem, and the results are compared to traditional scaling methods as well as explicit MC21 heating calculations. It is concluded that for experiment locations in close proximity to the ATR driver fuel (i.e. flux traps and the A, H, and B positions), heating rates scaled with the updated fractional contributions generally agree better with explicit MC21 calculations than do heating rates scaled using the traditionally assumed contributions. For the I positions, which are located on the very periphery of the ATR core, both scaling methods led to poor results when compared against explicit calculations due to the effect that movement of the outer shim control cylinders has on the experiment heating in those positions.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS

Computational wing design in support of an NLF variable sweep transition flight experiment

A natural laminar flow outer panel wing glove has been designed for a variable sweep fighter aircraft using state-of-the-art computational techniques. Testing of the design will yield wing pressure and boundary-layer data under actual flight conditions and environment. These data will be used to enhance the understanding of the interaction between crossflow and Tollmien-Schlichting disturbances on boundary-layer transition. The outer wing panel was contoured such that a wide range of favorable pressure gradients could be obtained on the wing upper surface. Extensive computations were performed to support the design effort which relied on two- and three-dimensional transonic design and analysis techniques. A detailed description of the design procedure that evolved during this study is presented. Results on intermediate designs at various stages in the design process demonstrate how the various physical and aerodynamic constraints were integrated into the design. Final results of the glove design analyzed as part of the complete aircraft configuration with a full-potential wing/body analysis code indicate that the aerodynamic design objectives were met.

Waggoner, E. G.

Numerical Investigation and Optimization of a Flushwall Injector for Scramjet Applications at Hypervelocity Flow Conditions

An investigation utilizing Reynolds-averaged simulations (RAS) was performed in order to demonstrate the use of design and analysis of computer experiments (DACE) methods in Sandia’s DAKOTA software package for surrogate modeling and optimization. These methods were applied to a flow- path fueled with an interdigitated flushwall injector suitable for scramjet applications at hyper- velocity conditions and ascending along a constant dynamic pressure flight trajectory. The flight Mach number, duct height, spanwise width, and injection angle were the design variables selected to maximize two objective functions: the thrust potential and combustion efficiency. Because the RAS of this case are computationally expensive, surrogate models are used for optimization. To build a surrogate model a RAS database is created. The sequence of the design variables comprising the database were generated using a Latin hypercube sampling (LHS) method. A methodology was also developed to automatically build geometries and generate structured grids for each design point. The ensuing RAS analysis generated the simulation database from which the two objective functions were computed using a one-dimensionalization (1D) of the three-dimensional simulation data. The data were fitted using four surrogate models: an artificial neural network (ANN), a cubic polynomial, a quadratic polynomial, and a Kriging model. Variance-based decomposition showed that both objective functions were primarily driven by changes in the duct height. Multiobjective design optimization was performed for all four surrogate models via a genetic algorithm method. Optimal solutions were obtained at the upper and lower bounds of the flight Mach number range. The Kriging model predicted an optimal solution set that exhibited high values for both objective functions. Additionally, three challenge points were selected to assess the designs on the Pareto fronts. Further sampling among the designs of the Pareto fronts may be required to lower the surrogate model errors and perform more accurate surrogate-model-based optimization.

Shenoy, Rajiv R.

Computer-Graphical Simulation Of Robotic Welding

Computer program ROBOSIM, developed to simulate operations of robots, applied to preliminary design of robotic arc-welding operation. Limitations on equipment investigated in advance to prevent expensive mistakes. Computer makes drawing of robotic welder and workpiece on positioning table. Such numerical simulation used to perform rapid, safe experiments in computer-aided design or manufacturing.

Fernandez, Ken

Surrogate Modeling and Optimization of a Combustor with an Interdigitated Flushwall Injector

Design and Analysis of Computer Experiments (DACE) methods are applied and used to perform surrogate modeling and optimization of a simplified combustor flowpath with an interdigitated flushwall injector. The objectives of the optimization are the thrust potential and combustion efficiency, which are evaluated across a range of flight Mach numbers, duct heights, spanwise spacings, and injection angles. The focus of this work is to highlight the application of a sequential learning approach, in order to learn about the responses of the objective functions over the design space and to identify local regions of interest for further analysis. This approach is contrasted to a previous effort where only a single sampling set was used to fit surrogate models and perform optimization. The optimal solutions resulting from the previous and present approaches are different, due to surrogate model-guided local refinement of the design space allowed by the sequential learning method. The values of the global error estimates between the previous and present approaches are comparable, but the sequential method proved more computationally cost-effective. Further refinement in the optimal regions might be needed to improve predictive capability of surrogate models and to obtain the optimal solutions sets.

Rajiv R Shenoy

AUTOTEST - Fully automated testing of spacecraft and experiments

AUTOTEST is a large scale real-time computer program designed to automatically test spacecraft and experiments. Resident portions of the program collect and store incoming real-time data and process test control instructions which control experiment turn-on, select tests to be performed, and select data to be displayed.

Blakeslee, W. D.

Software fault-tolerance by design diversity DEDIX: A tool for experiments

The use of multiple versions of a computer program, independently designed from a common specification, to reduce the effects of an error is discussed. If these versions are designed by independent programming teams, it is expected that a fault in one version will not have the same behavior as any fault in the other versions. Since the errors in the output of the versions are different and uncorrelated, it is possible to run the versions concurrently, cross-check their results at prespecified points, and mask errors. A DEsign DIversity eXperiments (DEDIX) testbed was implemented to study the influence of common mode errors which can result in a failure of the entire system. The layered design of DEDIX and its decision algorithm are described.

Avizienis, A.

A computer program to determine the possible daily release window for sky target experiments

A computer program is presented which is designed to determine the daily release window for sky target experiments. Factors considered in the program include: (1) target illumination by the sun at release time and during the tracking period; (2) look angle elevation above local horizon from each tracking station to the target; (3) solar depression angle from the local horizon of each tracking station during the experimental period after target release; (4) lunar depression angle from the local horizon of each tracking station during the experimental period after target release; and (5) total sky background brightness as seen from each tracking station while viewing the target. Program output is produced in both graphic and data form. Output data can be plotted for a single calendar month or year. The numerical values used to generate the plots are furnished to permit a more detailed review of the computed daily release windows.

Michaud, N. H.

Making aerospace technology work for the automotive industry - Introduction

In many cases it has been found that advances made in one technical field can contribute to other fields. An investigation is in this connection conducted concerning subjects from contemporary NASA programs and projects which might have relevance and potential usefulness to the automotive industry. Examples regarding aerospace developments which have been utilized by the automotive industry are related to electronic design, computer systems, quality control experience, a NASA combustion scanner and television display, exhaust gas analyzers, and a device for suppressing noise propagated through ducts. Projects undertaken by NASA's center for propulsion and power research are examined with respect to their value for the automotive industry. As a result of some of these projects, a gas turbine engine and a Stirling engine might each become a possible alternative to the conventional spark ignition engine.

Olson, W. T.

Theoretical analyses of baroclinic flows

Completed and ongoing research activities are discussed briefly, including a three-dimensional, linear stability analysis of the baroclinic Hadley cell and a numerical model of the baroclinic flow between two rotating concentric spheres. This model simulates axisymmetric flow in the Atmospheric General Circulation Experiment configuration. A computer code designed to solve the strongly nonlinear stability problem for the Eady basic state is mentioned.

Antar, B. N.

Dynamics of three-dimensional space crane - Motion requirements and computational considerations

Preliminary design requirements for a space crane are surveyed and some theoretical and computational issues that need to be addressed in support of the design activities are identified. Computational experiments conducted so far on rigid space crane models indicate that the sizing of joint actuators and operational constraints can be assessed by quasi-static rigid crane maneuvering simulations. Limited numerical experiments on flexible crane models raise several difficulties in developing control strategies, maneuvering speeds, maximum torque sustainable, and modeling detailed flexibility effects on the tip positioning accuracy. Computational algorithms development that will alleviate some of these difficulties are discussed and illustrated via example test runs.

Park, K. C.

Design and Implementation of the PALM-3000 Real-Time Control System

This paper reflects, from a computational perspective, on the experience gathered in designing and implementing realtime control of the PALM-3000 adaptive optics system currently in operation at the Palomar Observatory. We review the algorithms that serve as functional requirements driving the architecture developed, and describe key design issues and solutions that contributed to the system's low compute-latency. Additionally, we describe an implementation of dense matrix-vector-multiplication for wavefront reconstruction that exceeds 95% of the maximum sustained achievable bandwidth on NVIDIA Geforce 8800GTX GPU.

PALM-3000

Portable computing - A fielded interactive scientific application in a small off-the-shelf package

Experience with the design and implementation of a portable computing system for STS crew-conducted science is discussed. Principal-Investigator-in-a-Box (PI) will help the SLS-2 astronauts perform vestibular (human orientation system) experiments in flight. PI is an interactive system that provides data acquisition and analysis, experiment step rescheduling, and various other forms of reasoning to astronaut users. The hardware architecture of PI consists of a computer and an analog interface box. 'Off-the-shelf' equipment is employed in the system wherever possible in an effort to use widely available tools and then to add custom functionality and application codes to them. Other projects which can help prospective teams to learn more about portable computing in space are also discussed.

Groleau, Nicolas

Inverse problems and optimal experiment design in unsteady heat transfer processes identification

Experimental-computational methods for estimating characteristics of unsteady heat transfer processes are analyzed. The methods are based on the principles of distributed parameter system identification. The theoretical basis of such methods is the numerical solution of nonlinear ill-posed inverse heat transfer problems and optimal experiment design problems. Numerical techniques for solving problems are briefly reviewed. The results of the practical application of identification methods are demonstrated when estimating effective thermophysical characteristics of composite materials and thermal contact resistance in two-layer systems.

Artyukhin, Eugene A.

AMMPER: a user-friendly agent-based model that recapitulates simple metabolic responses of yeast to deep-space radiation

For humans venturing to deep space, radiation exposure poses a major health risk. Fundamental research into the biological effects of space radiation are essential for enabling exploration, and the first experimental organisms we send to deep space will be microbial. Yet there are many ways in which microorganisms are likely to experience the effects of high-energy particle radiation (such as Galactic Cosmic Rays) differently from multicellular animals, partly due to the simple fact that microbes are small and unicellular-- less likely to get hit in the first place, and less likely to communicate damage between cells. Computational modeling can aid in designing experiments and predicting the biological effects of radiation, but thus far particle radiation models have not focused on microbes. Here we present the latest developments in AMMPER, the Agent-based Model for Microbial Populations Exposed to Radiation. Originally written in 2021, AMMPER is a Python-based model that incorporates radiation track data from NASA's RITRACKS software and simulates the growth, damage, and death of yeast cells in 3D. It is now freely available as an open-source package on NASA's GitHub repository. Recent improvements include the ability to simulate the dynamics of alamarBlue, a color-changing redox dye commonly used to track metabolic activity in microbial spaceflight experiments. We demonstrate that a simple blue-pink-clear transition model is able to recapitulate key features observed in empirical data from ground studies. AMMPER also includes a new graphical user interface and introductory tutorial to facilitate ease of use by a wider audience. AMMPER can help us to understand how spatially heterogeneous particle radiation damage at the single-cell level can translate to growth differences at the population level, ultimately allowing us to better interpret experiments using microbes as model organisms and how well their results apply to humans.

yeast