Search NASA⌕ Search

SEARCH · Search NASA

Results for “differential pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Submersible Multistage Centrifugal Pump for Versatile Test Reactor Cartridge Test Loop

Submersible multistage centrifugal pumps are ideal for pumping in narrow confined spaces and achieving necessary head pressures and flow rates. Once a diameter is determined then manipulation of the number of stages and motor speed are all that are required to meet desired flow conditions. The Versatile Test Reactor (VTR) closed loop cartridge systems will need forced convection cooling independent of the main reactor. A multistage centrifugal pump can meet the necessary flow rates and pumping pressures while minimizing space taken. The pump considered for this work was based off a deep well submersible pump, a variation of a multistage centrifugal pump. We experimented with two pump sizes, 5 cm (2 inch) and 7.5 cm (3 inch) diameters. These diameters were chosen to fit into the inner diameter of standard 5 and 7.5 (2 and 3 inch) Schedule 40 pipe, respectively. This made the design for the test loop both simpler and less expensive as the need for an engineered pump housing was eliminated. Initial test cartridge planning indicated space for only a 5 cm (2 inch) diameter pump, though early testing of this size showed the need for an abnormally high-speed and high-power motor. Fine tuning of the cartridge design allowed a pump size increase to 7.5 cm (3 inches), which was the pump size most extensively tested in this work. The test loop is composed of various sizes of PVC and aluminum piping components in a loop configuration. The pump is driven by a Pittman 250 W (1/3 horsepower) electric motor with maximum speed of 3,450 RPM. Testing consisted of running the pump at a constant motor speed while varying a control valve to restrict flow through the loop, with differential pressure and flow rate recorded. This was done for one and two stage configurations for the 5 cm (2 inch) diameter impeller design and one, two, and three stage configurations for the 7.5 cm (3 inch diameter) impeller design, respectively. Due to pumping power requirements, two and three stage 7.5 cm (3 inch) diameter impeller testing at higher flowrates lowered the motor speed substantially. In regions where motor speed could not be maintained constant, the data were discarded. The test loop was also reconfigured to allow for the pump to be tested for pressure drop in a stalled or inoperable (0 RPM) flow condition. Demonstration of adequate natural convection cooling of the test cartridge fuel type is necessary under accident conditions, and this will depend upon the flow resistance through the impeller assembly when the pump is not operating. Thus, accurate knowledge of the effective impeller assembly loss coefficient is important for safety evaluations. The test loop was modified to provide water inlet and outlets on either side of the pump impeller stack, and a metered flow of lab water was provided in order to measure the pressure drop across the cartridges as a function of flowrate. Data from the pump head curve testing developed as part of this work and supported by analysis using pump head affinity laws indicates that a three stage 7.5 cm (3 inch) pump impeller design will meet target requirements for coolant flow within the VTR cartridge sodium cartridge at full power conditions [1] with margin; this corresponds to a flowrate of 45 l/min (12 gpm) at a pressure drop of 6.1 m (20 feet) of water head. The results of the pressure loss measurements across the impeller assembly when the pump is stationary (i.e., at 0 RPM) indicate that the pressure loss coefficient is 0.921 for a two impeller stack configuration; this value is calculated based on the flow velocity through the minimum available flow area within a single stage of the impeller which corresponds to 1.4 cm2.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

A combination interferometric and morphological image processing approach to rapid quality assessment of additively manufactured cellular truss core components

Advanced manufacturing (AM) processes such as laser powder bed fusion (LPBF) are increasingly capable of fabricating components with useful and unprecedented mechanical properties by incorporating complex internal bracing structures. From the standpoint of quality control and assessment, however, internally complex assemblies present significant build-verification challenges. Here we propose a hybrid approach to the inspection involving the application of computer-aided speckle interferometry (CASI) and morphological image processing as a rapid, inexpensive, and facile method for AM quality control. The described methodology has low capital equipment costs, is full-field and non-contact, can be used in an industrial setting, and has very low requirements in terms of operator training and expertise. Consisting primarily of the combination of image processing software with a simple optical system of variable sensitivity, the method is shown to be effective for inspection of a titanium honeycomb component subjected to differential pressure. Results are compared to those achieved with computed tomography (CT), immersion ultrasound testing (UT), and optical holographic interferometry. Here we propose several possible processing strategies for automated quality assessment based on this powerful hybrid approach.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Rapid determination of supercritical CO 2 and brine relative permeability using an unsteady-state flow method

In this study, relative permeability of supercritical CO 2 (scCO 2 ) and brine was determined in reactive and non-reactive rock cores using a combination of unsteady-state methodology and computed tomography. Experiments were conducted using a medical grade CT scanner to determine saturation using a custom Python script. The saturation and differential pressure across the core were then used to derive four empirical constants to calculate relative permeability. This methodology increases temporal efficiency while reducing experimental complexity. Additionally, we show that the method can be used to determine scCO 2 relative permeability in a wide range of lithologies and flow rates, and with the ability to account for matrix dissolution during scCO 2 flooding.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Thermal and hydraulic performance of volumetrically heated triply periodic minimal surface heaters

Advanced heat transfer surfaces, mainly Triply Periodic Minimal Surfaces (TPMSs) have great potential to increase heat transfer performance over traditional heat transfer surfaces due to their tortuous flow path and higher surface area-volume ratio. The emergence of additive manufacturing of nuclear fuel motivates experimental investigation of such advanced geometries in the context of a nuclear reactor core. Here, this study employed a novel method to explore the performance of gyroid and diamond TPMS geometries. Volumetrically heated heaters were additively manufactured from conductive polymer filament, and airflow was used to simulate the convective heat transfer from the core within a nuclear reactor. The mass flow and volumetric generation rates were varied, local Nusselt number correlations were obtained using embedded thermocouples to measure the solid and fluid temperature, and friction factor correlations were developed using differential pressure measurements. The gyroid TPMS presented a friction factor 1.5 times higher than the diamond TPMS and 90 times that of the rod bundle. TPMS geometries showed Nusselt numbers 8–10 times higher than that of the rod bundle, also maintaining colder internal temperatures, which suggested that they could sustain 250–275 % higher power density than the rod bundle for a given centerline temperature. Hence, having the potential to greatly increase the safety margins and power output of a nuclear reactor core with similar volume.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Numerical study on spray collapse process of ECN spray G injector under flash boiling conditions

This work features a numerical study of the spray collapse process that occurs under flash-boiling, gasoline-direct-injection conditions. The Engine Combustion Network's Spray G injector was modeled, and iso-octane, n-hexane, and propane were used as fuels with the goal to investigate fuel property effects. The development of individual jets and jet-to-jet interaction were analyzed to reveal the physical mechanisms of spray collapse. The results agreed qualitatively well with the experimental data of propane available from the literature and the predictions revealed the model's ability to capture the near-nozzle shock structures witnessed in the experiments. Simulations showed that the flow development of flashing sprays was strongly tied with the fuel properties. Specifically, under-expanded jets were not observed with iso-octane due to the fuel's low vapor pressure. In the case of n-hexane, the jets were under-expanded, and a low-pressure core was observed inside the jets due to the flow expansion. With propane, the very strong expansion caused the flow to become transonic and generate a unique shock structure near the nozzle exit. The shock structure revealed the formation of primary shock cells within the jets and secondary shock cells induced by jet-to-jet interaction. Based on the results, the spray collapse under flash boiling conditions was mainly attributed to two effects, i.e., the decrease in pressure at the spray center induced by the low-pressure cores inside and between the jets, and the isolation effect due to the jet-to-jet interaction which contributed to maintain the pressure differential between the spray center and the ambient.

42 ENGINEERING↗
DOE OSTI2025

Experimental investigation of flow distribution in enhanced geothermal systems with deep eutectic solvent

Geothermal energy has been recognized as a valuable alternative to fossil fuels and nuclear power, as it is renewable and reliable. Enhanced Geothermal Systems (EGSs) have the potential to expand geothermal energy production by enabling access to previously untapped geothermal resources. Geothermal short-circuiting poses a significant challenge to EGS development, leading to reduced heat extraction. Deep Eutectic Solvent (DES) exhibits favorable thermal and rheological properties, making it a candidate for geothermal applications. Here, this paper examines Choline Chloride-Based Deep Eutectic Solvent (DES) as a working fluid in geothermal applications and its potential to mitigate geothermal short-circuiting. Hydraulic experiments using a dual fracture flow loop were conducted at high temperatures. The results showed that DES exhibited higher differential pressure behavior compared to water. Flow distribution results revealed that DES enhances flow allocation within the small fracture, particularly when a temperature difference exists between fractures. Specifically, DES increased flow distribution by an average of 11% when the temperature difference was 85°C, and by 13% when the difference was 45°C, relative to water. These findings suggest that DES responds to thermal fracture differences, making it a potential remedy to address geothermal short-circuiting.

15 GEOTHERMAL ENERGY↗
DOE OSTI2025

Innovative duo-recombination layer design for effective hydrogen crossover mitigation in advanced MEAs for PEM water electrolyzers

Hydrogen crossover in proton exchange membrane water electrolyzers (PEMWEs) poses a safety hazard, reduces the overall efficiency, and limits the operational differential pressure range. Here, in this study, a membrane electrode assembly (MEA) with innovative Pt duo-recombination layer (DRL) design is developed by the unique reactive spray deposition technology (RSDT). The novel design comprises two thin RLs integrated within the volume of the membrane and has a total Pt loading of only 0.04 mg Pt cm −2 . Long-term durability test for over 3000 h is performed with as-fabricated MEA at steady-state conditions typical for an industrial hydrogen production system. The results from the durability test show that the newly developed DRL design effectively suppresses the H2 crossover to below 0.5 vol%. Furthermore, comprehensive post-test characterization of the MEA is performed and potential failure mechanisms in the Pt RLs observed during the durability test are identified and discussed in detail for the first time.

08 HYDROGEN↗
DOE OSTI2021

Gouge formation and dilation impacts to flow during fracture shearing

We report flow in fractures is of critical importance to fluid flow in low-permeability shales, particularly when they restrict vertical migration from reservoirs. The Mt. Simon Sandstone is a target for geologic CO 2 sequestration and the overlying Eau Claire Formation is the sealing formation capping this reservoir. The lower Eau Claire, a primary barrier to upward migration of CO 2 from the Mt. Simon, is lithologically heterogenous with a mixture of sandstone and shale. We use a series of flow-through experiments on fractured samples from the Eau Claire to document the morphological changes taking place in the fracture and surrounding rock as it is sheared in a stepwise fashion. The samples were imaged using computed tomography after each shearing episode and flow resistance was calculated based on the pressure differential across each core. We found that gouge accumulations in the fracture plane led to specific instances of self-sealing behavior despite the fact that most samples increased in average fracture aperture and transmissivity. Gouge limited the increase or, in some cases, decreased flow through these samples. Fractures adjacent to shale-rich zones and concordant with bedding were more likely to show evidence of self-sealing, while increased sandstone content and fracture orientation perpendicular to bedding planes was more likely to result in fracture dilation and fracture permeability increases. Reactivation and shearing of vertical fractures in lithologically heterogenous caprocks is more likely to pose risks to long term CO 2 storage scenarios.

58 GEOSCIENCES↗
DOE OSTI2020

Protection of graphite from salt and gas permeation in molten salt reactors

The reactor core, moderator and reflectors of a thermal spectrum advanced molten salt reactor will constitute multi-tons of graphite. Porous reactor-grade graphite, if unprotected, can be permeated by molten salt depending on the infiltrating pressure differential and entrance diameters of accessible graphite pores. Salt and gas permeation of graphite can affect microstructural properties and radiation behavior but also facilitate diffusion, deposition and retention of fission products and tritium. Because of the significant void volume of nuclear graphite, fission products and tritium retention due to salt permeation necessitates seal coatings or pore impregnation to reduce open porosity. Alternatively, very fine-grained graphite grades with low Xe permeability are being developed. In this work, we survey the current technologies for mitigating salt and gas transport into graphite.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Computational modeling of graphite degradation in molten salt reactors: Role of infiltration

Molten salt reactors (MSRs) often employ graphite as a moderator and reflector. An important challenge for deploying graphite in these reactors is that, due to limited experimental data, our understanding of graphite’s structural integrity in molten salt environments remains incomplete. Here, this study addresses heat generation from fuel-bearing salt that has infiltrated open pores in the graphite, driven primarily by pressure differentials. This is one of multiple identified physical and chemical mechanisms through which molten salt could potentially degrade graphite. Thermally driven stresses are quantified using the Molten-Salt Reactor Experiment (MSRE) graphite moderator elements as a case study. Finite element simulations predict stress distributions at varying infiltration levels, indicating that thermal stresses increase with higher infiltration. Rare-event simulations using the parallel subset simulation framework identify the combinations and corresponding ranges of input parameters that lead to stresses above a specified threshold. In particular, combinations involving high infiltration amounts, high power density, and low thermal conductivity tend to induce the highest stresses. Under the inputs and assumptions considered in this work, the magnitudes of the thermally driven stresses are quite low, with a very low likelihood of causing failure due to exceeding the graphite’s tensile strength. Additionally, rare-event simulations were performed for two more scenarios: a scaled-up moderator geometry and a localized hotspot in the original geometry. Both cases resulted in increased susceptibility to failure, though not to a detrimental extent. Furthermore, the combined effects of irradiation and infiltration-induced thermal stresses were evaluated. The results showed that thermal stresses from infiltration were negligible compared to those caused by irradiation. The findings of such a study are inherently component-specific, but the methodology presented here could be used for similar assessments of salt-infiltration effects in other graphite components.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Pure-Water-Fed Forward-Bias Bipolar Membrane CO 2 Electrolyzer

Coupling renewable electricity to reduce carbon dioxide (CO 2 ) electrochemically into carbon feedstocks offers a promising pathway to produce chemical fuels sustainably. While there has been success in developing materials and theory for CO 2 reduction, the widespread deployment of CO 2 electrolyzers has been hindered by challenges in the reactor design and operational stability due to CO 2 crossover and (bi)carbonate salt precipitation. Herein, we design asymmetrical bipolar membranes assembled into a zero-gap CO 2 electrolyzer fed with pure water, solving both challenges. By investigating and optimizing the anion-exchangelayer thickness, cathode differential pressure, and cell temperature, the forward-bias bipolar membrane CO 2 electrolyzer achieves a CO faradic efficiency over 80% with a partial current density over 200 mA cm –2 at less than 3.0 V with negligible CO 2 crossover. In addition, this electrolyzer achieves 0.61 and 2.1 mV h –1 decay rates at 150 and 300 mA cm –2 for 200 and 100 h, respectively. Postmortem analysis indicates that the deterioration of catalyst/polymer– electrolyte interfaces resulted from catalyst structural change, and ionomer degradation at reductive potential shows the decay mechanism. Furthermore, all these results point to the future research direction and show a promising pathway to deploy CO 2 electrolyzers at scale for industrial applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

The charge reduction rate for multiply charged polymer ions via ion–ion recombination at atmospheric pressure

The charge reduction of multiply charged macromolecular ions via recombination with small ions in the gas phase is commonly employed to modulate the charge on macromolecules prior to mass spectrometric and mobility analyses. We employ a recently developed continuum-Molecular Dynamics (MD) calculation approach to determine the recombination rate coefficient of multiply charged (1 to 7 excess positive charged) polyethylene glycol ions (mass of 4600 Da) with smaller singly charged anions, modeled as NO 2 – ions. The continuum-MD approach accounts explicitly for the influence of the background gas on the recombination process, accounts explicitly for ion translational, vibrational, and rotational motion, and enables recombination rate coefficient calculation in nitrogen near atmospheric pressure, wherein neither low pressure nor high pressure recombination theories are strictly applicable. Continuum-MD simulations yield recombination rate coefficients near 3.9 × 10 –14 m 3 s –1 for singly charged ions, increasing to 3.0 × 10 –11 m 3 s –1 for the +7 ion. Pre-existing collision rate coefficient expressions for rigid ions are found to be within a factor of 2–5 of calculations for all charge states, but their use requires knowledge of an appropriate collision distance, which is not well-defined for flexible polymer ions. Continuum-MD-inferred rate coefficients are incorporated into a model of charge reduction, and the charge state distribution versus anion concentration determined with it is compared to charge reduction measurements made via atmospheric pressure differential mobility analysis. Furthermore, good agreement is observed between simulations and experiments; although results are extremely sensitive to the recombination rate coefficients, experimental results are bound by models utilizing rates within a factor of 2 (0.5–2.0×) of the continuum-MD rates.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Performance and durability of anion exchange membrane water electrolyzers using down-selected polymer electrolytes

Over the last decade, several stable anion exchange polymer electrolytes have been developed for electrochemical devices. Herein, we investigate how chemical structure and physical properties of polymer electrolytes affect performance and durability of anion exchange membrane water electrolyzers (AEMWEs). We select polymer electrolytes with high alkaline stability and consider their polymer properties including conductivity, mechanical/chemical stability, and material interactions to interpret the performance and durability of AEMWEs. Here, the AEMWE with a poly(phenylene) membrane and a poly(fluorene) ionomeric binder exhibited the best performance among those tested in this study; the AEMWE showed ~1 A cm –2 at 2 V under 1 wt% K 2 CO 3 -fed conditions. The voltage degradation rate was 270–550 μV h –1 for several hundred operating hours at a constant current density of 750 mA cm –2 and a differential pressure of 100 pounds per square inch gauge. Based on these results, we discuss research needs of polymer electrolytes for practical AEMWEs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Plasma window performance and scaling for an accelerator-based neutron source

A “plasma window” was developed for use with a SHINE accelerator-based neutron source. In this work, the design of the plasma window is presented along with results demonstrating successful operation in deuterium over a range of aperture diameters (5–12 mm), gas flow rates (3.5 to 12.5 slm), and input powers (10–55 kW). Here, an empirically determined relationship between the aperture diameter, deuterium gas flow rate, input power, and plasma window pressure differential is also presented.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Radon Kinetics in a Basement Space Measured with Different Devices

Although indoor monitoring of radon and benchmarking of radon measurement devices remain important research topics, few intercomparisons of active radon measurement devices have been performed under realistic conditions, let alone dynamic ones enabling comparison of their transient behavior. Five different radon monitors were therefore placed in a poorly ventilated basement space under three different conditions: 24 h under a steady, elevated radon level, 24 h with fans turned on to produce a radon washout transient, and 9 d with fans turned off for a radon buildup transient. Resulting radon concentrations varied between ~200 and ~2,000 Bq m -3 . Accuracy of the devices were evaluated using root-mean-square error, and ventilation data were fit to first order linear compartmental models. To more accurately model behaviors such as cyclic diurnal variations, the source term corresponding to entry of radon from soil into the basement was considered to be non-constant, as it is likely to vary drastically with both the indoor-outdoor pressure differential and soil concentration variations. Here, the improved radon washout model fit very well with the measurements. Despite a wide variety in list prices, all devices performed similarly during transients and at different radon concentrations.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

An Efficient Three-Dimensional CFD-Based Numerical Wave Tank for a Wave Energy Converter in Extreme Irregular Waves

A numerical wave tank approach for computational fluid dynamics (CFD) modelling of an extreme irregular seastate is presented. The technique couples a potential flow solution with a CFD solver for more efficient numerical predictions. This method has recently become attractive both for the research community and the industry working with offshore structures. The model is used to determine the response of a submerged pressure differential wave energy converter (WEC) in a fully nonlinear irregular wave condition using the high-fidelity CFD code, STAR-CCM+. Potential flow based numerical models are commonly used to predict motions and performance of wave energy converters. Wave kinematics can deviate from potential flow predictions for extreme wave conditions; the excitation loads on an absorber can also be increasingly influenced by viscous effects, not predicted by potential flow engineering level models. In these extreme conditions, a Reynolds-averaged Navier-Stokes CFD model can better predict motions and loads for a WEC. Long time series with varying random seed numbers can be used to identify singular extreme wave events from a stochastic irregular sea state. This approach simulates a more realistic wave series for a given sea state than a regular wave or a focused wave. However, it is computationally infeasible to run these long time series for three-dimensional (3D) CFD simulations. In this work, two-dimensional (2D) CFD simulations with a long domain allow the full development of an extreme nonlinear wave condition. The results are used to identify extreme events from a 50-year storm condition for the PacWave site off the coast of Oregon. A relatively short time window including this extreme event is then mapped to a 3D simulation using a user defined wave methodology. Convergence studies for domain length, wave forcing lengths, and time before the extreme event were conducted.

CFD↗
DOE OSTI2023

Tailoring the Mass Transport to Achieve High-Performing Unitized Regenerative Fuel Cells Considering Practical Operating Conditions

Unitized regenerative fuel cells (URFCs) convert electrical energy to chemical bonds in hydrogen during charge and convert chemical energy to output electricity during discharge, offering a promising solution to long-term energy storage. Recent studies indicate that the round-trip-voltaic efficiency (RTE) and longevity of URFCs are limited by complex mass transport during charging and discharging. Here, we first investigate how different porous transport layer (PTL) structures can impact URFC performance. The preferred PTL has a low tortuosity and high porosity, leading to a high RTE above 50% at 1 A cm −2 using Nafion 212. Moreover, thicker membranes, such as Solvay 90, are required to ensure mechanical stability and minimize H 2 crossover when operating under high differential pressure. Although this assembly inevitably leads to a higher ohmic loss, the RTE can be improved by further tailoring the electrode structures to facilitate mass transport by using supported catalyst, which still achieves over 50% RTEs at 1 A cm −2 . Optimization of porous structure to mitigate mass transport resistance with appropriate materials down selection considering practical application requirements can be a key design principle for achieving high-performing URFCs.

25 ENERGY STORAGE↗
DOE OSTI2024

Modeling In-Reactor Temperature Gradients in Lithium Aluminate Ceramic Pellets

In reactor thermal performance of lithium aluminate ceramic pellets are calculated to determine operating temperatures if internal components shift during irradiation. A 2D conduction model was setup to model this scenario with additional physics, including thermal expansion of components to reactor temperatures, creep down of the cladding due to differential pressure between the inside of the rod and reactor coolant system, and net radiation exchange between components. The non-linear coupling of the governing equations presented convergence challenges due to the very different effects from a small temperature change on the radiation vs radial and circumferential conduction equations. Initial temperature guesses for the multidimensional solution were provided from conservative 1D models simulating bounding scenarios. Convergence was greatly improved by taking small steps towards the root solutions and averaging with initial guesses. The final method robustly converged all 132 points at an axial plane after a few dozen iterations. The temperature results show that the additional physics have a secondary effect as the dominant heat transfer mechanism is radial conduction across the gas gap followed by circumferential conduction around components. Circumferential conduction in the lithium aluminate pellets is enhanced by the relatively high thermal conductivity of this ceramic.

Carstens, Nathan A.↗