Search NASA⌕ Search

SEARCH · Search NASA

Results for “displacement front”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

Characterization of the Edge Crack Torsion (ECT) Test for Mode III Fracture Toughness Measurement of Laminated Composites

The edge crack torsion (ECT) test is designed to initiate mode III delamination growth in composite laminates. The test has undergone several design changes during its development. The objective of this paper was to determine the suitability of the current ECT test design a mode III fracture test. To this end, ECT tests were conducted on specimens manufactured from IM7/8552 and S2/8552 tape laminates. Three-dimensional finite element analyses were performed. The analysis results were used to calculate the distribution of mode I, mode II, and mode III strain energy release rate along the delamination front. The results indicated that mode IIIdominated delamination growth would be initiated from the specimen center. However, in specimens of both material types, the measured values of GIIIc exhibited significant dependence on delamination length. Load-displacement response of the specimens exhibited significant deviation from linearity before specimen failure. X-radiographs of a sample of specimens revealed that damage was initiated in the specimens prior to failure. Further inspection of the failure surfaces is required to identify the damage and determine that mode III delamination is initiated in the specimens.

Ratcliffe, James G.↗
NASA NTRS1996

Electron Densities in Solar Flare Loops, Chromospheric Evaporation Upflows, and Acceleration Sites

We compare electron densities measured at three different locations in solar flares: (1) in Soft X-Ray (SXR) loops, determined from SXR emission measures and loop diameters from Yohkoh Soft X-Ray Telescope maps (n(sub e, sup SXR) = (0.2-2.5) x 10(exp 11)/ cu cm); (2) in chromospheric evaporation upflows, inferred from plasma frequency cutoffs of decimetric radio bursts detected with the 0.1-3 GHz spectrometer Phoenix of ETH Zuerich (n(sub e, sup upflow) = (0.3-11) x 10(exp 10)/cu cm; and (3) in acceleration sites, inferred from the plasma frequency at the separatrix between upward-accelerated (type III bursts) and downward-accelerated (reverse-drift bursts) electron beams [n(sub e, sup acc) = (0.6-10) x 10(exp 9)/cu cm]. The comparison of these density measurements, obtained from 44 flare episodes (during 14 different flares), demonstrates the compatibility of flare plasma density diagnostics with SXR and radio methods. The density in the upflowing plasma is found to be somewhat lower than in the filled loops, having ratios in a range n(sub e, sup upflow)/n(sub e, sup SXR) = 0.02-1.3, and a factor of 3.6 higher behind the upflow front. The acceleration sites are found to have a much lower density than the SXR-bright flare loops, i.e., n(sub e, sup acc)/n(sub e, sup SXR) = 0.005- 0.13, and thus must be physically displaced from the SXR-bright flare loops. The scaling law between electron time-of-flight distances l' and loop half-lengths s, l'/s = 1.4 +/- 0.3, recently established by Aschwanden et al. suggests that the centroid of the acceleration region is located above the SXR-bright flare loop, as envisioned in cusp geometries (e.g., in magnetic reconnection models).

Aschwanden, Markus J.↗
NASA NTRS1985

Observation of a coronal transient from 1.2 to 6 solar radii

The paper describes in detail the eruptive prominence associated coronal mas ejection of August 5, 1980, as seen in both the Solar Maximum Mission (SMM) coronagraph polarimeter and the Mauna Loa Observatory (MLO) K coronameter and prominence monitor. This event gives the first detailed look at the propagation of a 'depletion' transient into the outer corona. The event begins in the MLO K coronameter as a rising depletion of material, but appears later in the SMM coronograph as an ordinary coronal mass ejection with a three-part structure: a bright core within a dark lunette surrounded by a bright featureles 'loop'. A joint time-height plot of the major structures of the eruption seen by both instruments suggests that the three-part structure in the outer corona can be associated with features in the low corona (prominence, prominence cavity, outer bright front). It is argued from its observed mass that the leading loop in the SMM field of view is probably material that was in the background corona before the event. It is suggested that this material has been displaced and set into motion by the rising 'cavity.'

Illing, R. M. E.↗
NASA NTRS2018

Relevence of 3D Simulations and Sandwich Core Topology for the Modeling of Honeycomb Core Sandwich Panels Undergoing Mode I Delamination

A recently developed cohesive zone traction-separation law, which includes the effects of fiber bridging in a novel way, is extended from 2D to 3D. The proposed cohesive model is applied to low fidelity (i.e. homogenized core representation) and high fidelity (i.e. directly accounting for the core topology) finite element models of a composite panel comprised of carbon fiber reinforced plastic facesheets and a honeycomb sandwich core. This enables the investigation of 2D to 3D parameter transferability, width-dependent effects such as thumbnail-shaped crack growth, and the verification of plane strain / plane stress assumptions. A pronounced curvature of the initial interface-related crack front is observed, while the bridging-related crack front is straight. Furthermore, it is found that the cohesive parameters can easily be transferred from 2D to 3D under plane stress assumptions, but not under plane strain assumptions. The numerical predictions are compared to experimental load-displacement and R-curves.

Composites↗
NASA NTRS2017

Wavefront sensing for a future HabEx space telescope.

HabEx is a concept study for a next generation space telescope having a 4 to 6.5 m primary mirror diameter. Primarily designed for exoplanet science, but also carrying general astrophysics instruments, it will have stability requirements orders of magnitude more stringent than any previously flown space-based observatory. Wavefront control, including active sensing/control of wavefront jitter and drift, will be essential to achieving and maintaining coronagraph performance. There are currently two complementary techniques that can be used to sense the wavefront drift. An attractive method is to use starlight rejected from the coronagraph to sense changes in the wavefront incident on the coronagraph mask. This method suffers from photon noise especially when imaging dim stars. It is also unavailable during slews between target stars. Laser metrology is a complementary system in which a laser “truss” enables rigid body displacements of the optics to be measured from changes in the separation of pairs of optical fiducials which can be separated by many meters. In closed loop with actuated optics, laser metrology actively maintains rigid body alignment of the front-end optics, thereby eliminating the dominant source of wavefront drift. This method can maintain rigid body stability of the telescope optics and thereby wavefront control, even during slews between targets.

Martin, Stefan↗
NASA NTRS1992

Measurements of the interaction of wave groups with shorter wind-generated waves

Fields of statistically steady wind-generated waves produced in a wind wave facility were perturbed by the injection of groups of longer, mechanically generated waves with various slopes. The time histories of the surface displacements were measured at four fetches in ensembles consisting of 100 realizations of each set of experimental conditions; the data were stored and analyzed digitally. Four distinct stages in the overall interaction are identified and characterized. The properties of the wave energy front are documented, and a preliminary discussion is given of the dynamic processes involved in its formation.

Chu, Jacob S.↗
NASA NTRS1997

ENSO Mechanisms

This current leading theory of the El Nino-Southern Oscillation (ENSO) phenomenon involves reflection of equatorial waves on the western ocean boundary to shift the ENSO phase from El Nino to La Nina and vice versa. However, recent satellite altimetry and In situ observations indicate that this theory has several flaws. These include imperfect equatorial wave reflection on the western ocean boundary, a maxima of the simulated coupled wind-sea surface temperature (SST) interaction located too far into the eastern equatorial Pacific, and an excessive role of thermocline displacement on SST in this region. We show that the central equatorial Pacific SST is fundamental in driving the EIVSO ocean-atmosphere coupled system, through the east-west displacement of the eastern edge of the warm pool, perfectly related with ENSO. Within the equatorial wave-guide, the dominance of surface zonal advection in these displacements is demonstrated with four different satellite and in situ data sets and three ocean models. This demonstration is supported by the evidence of a convergence of water masses into the eastern edge of the warm pool, resulting in a well-defined salinity front. All these results lead us to propose a notable modification of the leading delayed-action oscillator theory for the oscillatory nature of ENSO. Simulations with a linearized coupled ocean-atmosphere model result in 3-6 year ENSO-like oscillations, with many Of the variable model parameters found very close to their observed values. This simple model suggests that ocean processes ignored or underestimated in the delayed action oscillator theory, such as zonal current convergence, zonal advection of sea surface temperature and equatorial wave reflection from the eastern-ocean boundary, are fundamental to the development of ENSO, in particular to its manifestations in the central equatorial Pacific.

Picaut, Joel↗
NASA NTRS1987

Energy dissipation associated with crack extension in an elastic-plastic material

Crack extension in elastic-plastic material involves energy dissipation through the creation of new crack surfaces and additional yielding around the crack front. An analytical procedure, using a two-dimensional elastic-plastic finite element method, was developed to calculate the energy dissipation components during a quasi-static crack extension. The fracture of an isotropic compact specimen was numerically simulated using the critical crack-tip-opening-displacement (CTOD) growth criterion. Two specimen sizes were analyzed for three values of critical CTOD. Results from the analyses showed that the total energy dissipation rate consisted of three components: the crack separation energy rate, the plastic energy dissipation rate, and the residual strain energy rate. All three energy dissipation components and the total energy dissipation rate initially increased with crack extension and finally reached constant values.

Shivakumar, K. N.↗
NASA NTRS1987

Energy dissipation associated with crack extension in an elastic-plastic material

Crack extension in elastic-plastic material involves energy dissipation through the creation of new crack surfaces and additional yielding around the crack front. An analytical procedure, using a two-dimensional elastic-plastic finite element method, was developed to calculate the energy dissipation components during a quasi-static crack extension. The fracture of an isotropic compact specimen was numerically simulated using the critical crack-tip-opening-displacement (CTOD) growth criterion. Two specimen sizes were analyzed for three values of critical CTOD. Results from the analysis showed that the total energy dissipation rate consisted of three components: the crack separation energy rate, the plastic energy dissipation rate, and the residual strain energy rate. All three energy dissipation components and the total energy dissipation rate initially increased with crack extension and finally reached constant values.

Shivakumar, K. N.↗
NASA NTRS1979

Definition of Mutually Optimum NDI and Proof Test Criteria for 2219 Aluminum Pressure Vessels. Volume 2: Optimization and Fracture Studies

Certain behavioral aspects associated with fracture and crack extension that cannot be studied using other techniques were evaluated with the ultrasonic method. Characterization of collimated beam techniques showed that significant beam width reduction could be accomplished. Techniques for collimation are given. The crack-opening displacement-gage correction-factor study showed that displacement resulting from crack opening and that from plasticity could be readily differentiated. Crack closure studies using both ultrasonic and crack-opening displacement measurements showed an opening and closing behavior associated with load-unload curves. The results of this work were in general agreement with the closure concepts of Elber. Ultrasonic measurements used to study the nature of flaw extension characteristics associated with failure of the ligament between the flaw front and back surface showed that penetration could occur by an abrupt fracturing after subcritical growth or by continuous growth.

Schwartzberg, F. R.↗
NASA NTRS1992

An inverse method for the calculation of through-thickness fatigue crack closure behavior

An inverse technique was used to calculate through-thickness fatigue crack closure behavior. The through-thickness variation in crack opening stress-intensity factor was calculated by considering the variation in the three-dimensional stress-intensity factor, the variation in crack growth rate along the crack front, and a relationship between the crack growth rate and effective stress-intensity factor range (da/dN-Delta-K(eff)). The three-dimensional stress-intensity factor variation was obtained from an elastic finite element analysis of specific crack-front profiles observed experimentally. The variation in crack growth rate along the crack front was obtained experimentally from comparison of observed crack front changes. The da/dN-Delta-K(eff) relationship was estimated from high stress ratio, constant load amplitude, and fatigue crack growth tests. The through-thickness crack opening stress-intensity factor results agreed with crack opening measurements obtained from fatigue striations, near-tip strain gages, and remote strain and displacement gages.

Dawicke, D. S.↗
NASA NTRS2004

Particle Acceleration, Magnetic Field Generation, and Emission in Relativistic Shocks

Shock acceleration is an ubiquitous phenomenon in astrophysical plasmas. Plasma waves and their associated instabilities (e.g., the Buneman instability, two-streaming instability, and the Weibel instability) created in the shocks are responsible for particle (electron, positron, and ion) acceleration. Using a 3-D relativistic electromagnetic particle (m) code, we have investigated particle acceleration associated with a relativistic jet front propagating through an ambient plasma with and without initial magnetic fields. We find only small differences in the results between no ambient and weak ambient parallel magnetic fields. Simulations show that the Weibel instability created in the collisionless shock front accelerates particles perpendicular and parallel to the jet propagation direction. New simulations with an ambient perpendicular magnetic field show the strong interaction between the relativistic jet and the magnetic fields. The magnetic fields are piled up by the jet and the jet electrons are bent, which creates currents and displacement currents. At the nonlinear stage, the magnetic fields are reversed by the current and the reconnection may take place. Due to these dynamics the jet and ambient electron are strongly accelerated in both parallel and perpendicular directions.

Nishikawa, Ken-IchiI.↗
NASA NTRS2005

Particle Acceleration, Magnetic Field Generation in Relativistic Shocks

Shock acceleration is an ubiquitous phenomenon in astrophysical plasmas. Plasma waves and their associated instabilities (e.g., the Buneman instability, two-streaming instability, and the Weibel instability) created in the shocks are responsible for particle (electron, positron, and ion) acceleration. Using a 3-D relativistic electromagnetic particle (REMP) code, we have investigated particle acceleration associated with a relativistic jet front propagating through an ambient plasma with and without initial magnetic fields. We find only small differences in the results between no ambient and weak ambient parallel magnetic fields. Simulations show that the Weibel instability created in the collisionless shock front accelerates particles perpendicular and parallel to the jet propagation direction. New simulations with an ambient perpendicular magnetic field show the strong interaction between the relativistic jet and the magnetic fields. The magnetic fields are piled up by the jet and the jet electrons are bent, which creates currents and displacement currents. At the nonlinear stage, the magnetic fields are reversed by the current and the reconnection may take place. Due to these dynamics the jet and ambient electron are strongly accelerated in both parallel and perpendicular directions.

Nishikawa, Ken-Ichi↗
NASA NTRS2004

Characterization of the Edge Crack Torsion (ECT) Test for Mode III Fracture Toughness Measurement of Laminated Composites

The edge crack torsion (ECT) test is designed to initiate mode III delamination growth in composite laminates. An ECT specimen is a rectangular laminate, containing an edge delamination at the laminate mid-plane. Torsion load is applied to the specimens, resulting in relative transverse shear sliding of the delaminated faces. The test data reduction schemes are intended to yield initiation values of critical mode III strain energy release rate, G(sub IIIc), that are constant with delamination length. The test has undergone several design changes during its development. The objective of this paper was to determine the suitability of the current ECT test design as a mode III fracture test. To this end, ECT tests were conducted on specimens manufactured from IM7/8552 and specimens made from S2/8552 tape laminates. Several specimens, each with different delamination lengths are tested. Detailed, three-dimensional finite element analyses of the specimens were performed. The analysis results were used to calculate the distribution of mode I, mode II, and mode III strain energy release rate along the delamination front. The results indicated that mode III-dominated delamination growth would be initiated from the specimen center. However, in specimens of both material types, the measured values of G(sub IIIc) exhibited significant dependence on delamination length. Furthermore, there was a large amount of scatter in the data. Load-displacement response of the specimens exhibited significant deviation from linearity before specimen failure. X-radiographs of a sample of specimens revealed that damage was initiated in the specimens prior to failure. Further inspection of the failure surfaces is required to identify the damage and determine that mode III delamination is initiated in the specimens.

Ratcliffe, James G.↗
NASA NTRS2003

Nanolaminate Mirrors With "Piston" Figure-Control Actuators

Efforts are under way to develop a special class of thin-shell curved mirrors for high-resolution imaging in visible and infrared light in a variety of terrestrial or extraterrestrial applications. These mirrors can have diameters of the order of a meter and include metallic film reflectors on nanolaminate substrates supported by multiple distributed piezoceramic gpiston h-type actuators for micron-level figure control. Whereas conventional glass mirrors of equivalent size and precision have areal mass densities between 50 and 150 kg/sq m, the nanolaminate mirrors, including not only the reflector/ shell portions but also the actuators and the backing structures needed to react the actuation forces, would have areal mass densities that may approach .5 kg/m2. Moreover, whereas fabrication of a conventional glass mirror of equivalent precision takes several years, the reflector/shell portion of a nanolaminate mirror can be fabricated in less than a week, and its actuation system can be fabricated in 1 to 2 months. The engineering of these mirrors involves a fusion of the technological heritage of multisegmented adaptive optics and deformable mirrors with more recent advances in metallic nanolaminates and in mathematical modeling of the deflections of thin, curved shells in response to displacements by multiple, distributed actuators. Because a nanolaminate shell is of the order of 10 times as strong as an otherwise identical shell made of a single, high-strength, non-nanolaminate metal suitable for mirror use, a nanolaminate mirror can be made very thin (typically between 100 and 150 m from the back of the nanolaminate substrate to the front reflecting surface). The thinness and strength of the nanolaminate are what make it possible to use distributed gpiston h-type actuators for surface figure control with minimal local concentrated distortion (called print-through in the art) at the actuation points.

Lowman, Andrew↗
NASA NTRS1975

On fracture toughness evaluation for semi-brittle fracture

The existing methods of assessing the fracture toughness of materials exhibiting semi-brittle fracture are critically reviewed. The methods concern the Crack Growth Resistance (R-curve), the Crack Opening Displacement (COD), and the J-integral. An analysis of the shortcomings of the methods described makes it possible to formulate a new definition of fracture toughness appropriate to semi-brittle fracture. An improved simple experimental method for measuring fracture toughness for semi-brittle fracture is proposed which takes into account both crack growth and plastic nonlinear effects at crack front. The proposed method is shown to be free of the theoretical and experimental discrepancies encountered in the R-curve, COD, and J-integral methods.

Eftis, J.↗
NASA NTRS2004

Characterization of Transport Errors in Chemical Forecasts from a Global Tropospheric Chemical Transport Model

We propose a new methodology to characterize errors in the representation of transport processes in chemical transport models. We constrain the evaluation of a global three-dimensional chemical transport model (GEOS-CHEM) with an extended dataset of carbon monoxide (CO) concentrations obtained during the Transport and Chemical Evolution over the Pacific (TRACE-P) aircraft campaign. The TRACEP mission took place over the western Pacific, a region frequently impacted by continental outflow associated with different synoptic-scale weather systems (such as cold fronts) and deep convection, and thus provides a valuable dataset. for our analysis. Model simulations using both forecast and assimilated meteorology are examined. Background CO concentrations are computed as a function of latitude and altitude and subsequently subtracted from both the observed and the model datasets to focus on the ability of the model to simulate variability on a synoptic scale. Different sampling strategies (i.e., spatial displacement and smoothing) are applied along the flight tracks to search for systematic model biases. Statistical quantities such as correlation coefficient and centered root-mean-square difference are computed between the simulated and the observed fields and are further inter-compared using Taylor diagrams. We find no systematic bias in the model for the TRACE-P region when we consider the entire dataset (i.e., from the surface to 12 km ). This result indicates that the transport error in our model is globally unbiased, which has important implications for using the model to conduct inverse modeling studies. Using the First-Look assimilated meteorology only provides little improvement of the correlation, in comparison with the forecast meteorology. These general statements can be refined when the entire dataset is divided into different vertical domains, i.e., the lower troposphere (less than 2 km), the middle troposphere (2-6 km), and the upper troposphere (greater than 6 km). The best agreement between the observations and the model is found in the lower and middle troposphere. Downward displacements in the lower troposphere provide a better fit with the observed value, which could indicate a problem in the representation of boundary layer height in the model. Significant improvement is also found for downward and southward displacements in the upper troposphere. There are several potential sources of errors in our simulation of the continental outflow in the upper troposphere which could lead to such biases, including the location and/or the strength of deep convective cells as well as that of wildfires in Southeast Asia.

Bey, I.↗
NASA NTRS1989

A high resolution electro-optical displacement measurement system

An improved electrooptical system has been developed to sense wind tunnel model position. The original system using 25.6 mm, 1024-element linear photodiode arrays (PDAs) is being successfully used at a NASA wind tunnel but has a limited range. A new two-channel system using 61.44 mm, 4096-element PDAs has been developed to double the range of vertical and pitch measurement and increase the resolution by 60 percent. The PDAs are illuminated by expanding the beam of a single low power helium neon laser into a collimated sheet of light. An object placed in front of the two parallel PDAs produces a shadow on the array apertures which determines the object's position or size. The system has an overall precision of 12.7 microns and + or - 0.015 degrees in linear and angular measurements.

Schott, Timothy D.↗