Search NASA⌕ Search

SEARCH · Search NASA

Results for “displacement thickness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Hermeticity of SiC/SiC composite and monolithic SiC tubes irradiated under radial high-heat flux

Demonstration of hermetic SiC fiber–reinforced SiC matrix composite cladding under normal operating environments has been identified as one of the most critical feasibility issues for accident-tolerant fuel cladding in light-water reactors. This study provides critical experimental data needed for understanding the effects of irradiation on hermeticity. SiC composite and monolithic tubes were neutron-irradiated to 2 displacements per atom with and without a nominal radial heat flux of 0.6 MW/m2 to produce a simulated in-pile stress state for the normal operation of a light-water reactor. The through-thickness temperature gradient under irradiation results in a gradient in swelling, which causes a significant stress buildup. Such irradiation-induced stress was modeled using a commercial finite element analysis code. The radial heat flux–irradiation synergism was experimentally investigated by constructing a special irradiation capsule and evaluating the helium hermeticity of the specimens. The simulated stress state exhibited a near equi-biaxial tensile axial and hoop stress of ~150 MPa at the inner surface of the SiC composite tube. This stress level is potentially beyond the matrix cracking stress. Degradation of hermeticity of the SiC composite tubes was observed after irradiation, indicating irradiation-induced cracking, whereas the irradiated monolithic SiC tubes remained hermetic. In conclusion, the results indicate that loss of hermeticity caused by radiation-induced microcracking is a potential issue for SiC composite cladding, depending on the magnitude of the temperature gradients. Coating the outer surface of the cladding was identified as a mitigation strategy that might overcome the cracking issue.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Achieving Flat-on Primary Crystals by Nanoconfined Crystallization in High-Temperature Polycarbonate/Poly(vinylidene fluoride) Multilayer Films and Its Effect on Dielectric Insulation

To meet the stringent requirements of next-generation film capacitors for power electronics, multilayer films (MLFs) are fabricated with the advantage of achieving high temperature rating, high energy density, and reasonably low loss simultaneously. In this study, a high permittivity polar polymer, poly(vinylidene fluoride) (PVDF), is multilayered with a linear, low loss dielectric polymer such as high-temperature polycarbonate (HTPC). However, the dielectric loss of these MLFs was still high as compared with current state-of-the-art biaxially oriented polypropylene (BOPP) films. The goal of this work is to decrease the dielectric loss and enhance dielectric insulation by achieving flat-on primary PVDF crystals in MLFs via nanoconfined melt-recrystallization. Based on simultaneous small- and wide-angle X-ray scattering experiments, edge-on lamellar crystals were observed for all as-extruded MLFs, regardless of different PVDF layer thicknesses. However, after melting at 180 °C followed by recrystallization, flat-on primary crystals were successfully achieved when the PVDF layer thickness was below 39 nm. Above 78 nm for the PVDF layer, major edge-on primary crystals with minor flat-on secondary crystals were observed. Furthermore, from leakage current, breakdown, lifetime, and electric displacement-electric field loop studies, MLFs with the flat-on primary crystals exhibited reduced loss and enhanced dielectric insulation as compared to as-extruded MLFs and those with edge-on primary/flat-on secondary crystals. This was attributed to the effective blockage of charge carriers by the flat-on PVDF primary crystals and their reduced ferroelectric switching.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Strain-stabilized interfacial polarization tunes work function over 1 eV in RuO 2 /TiO 2 heterostructures

Interfacial polarization – charge accumulation at the heterointerface – is a well-established tool in semiconductors, but its influence in metals remains unexplored. Here, we demonstrate that interfacial polarization can robustly modulate surface work function in metallic rutile RuO 2 layers in epitaxial RuO 2 /TiO 2 heterostructures grown by hybrid molecular beam epitaxy. Using multislice electron ptychography, we directly visualize polar displacements of transition metal ions relative to oxygen octahedra near the interface, despite the conductive nature of RuO 2 . This interfacial polarization enables over 1 eV modulation of the RuO 2 work function, controlled by small thickness variations (2-3 nm), as measured by Kelvin probe force microscopy, with a critical thickness of ~4 nm – corresponding to the transition from fully-strained to relaxed film. These results establish interfacial polarization as a powerful route to control electronic properties in metals and have implications for designing tunable electronic, catalytic, and quantum devices through interfacial control in polar metallic systems.

Electronic properties and materials↗
DOE OSTI2022

Visualizing electrode assembly movement and lithiation heterogeneity in lithium-metal batteries using operando energy dispersive X-ray diffraction

There is renewed interest in Li-metal anodes in order to increase the energy density of battery cells. Here, we demonstrate an operando X-ray crystallography method to visualize lithiation gradients and electrode assembly movement during electrochemical cycling of a Li-metal cell containing a Ni-Mn-Co layered oxide cathode (NMC811). During charge, deposition of Li + ions from the cathode increases the Li foil thickness; during discharge, the thickness decreases as Li + ions are stripped off the foil. Additionally, the resulting periodic movement is observed through tracking of Bragg peaks from the ordered phases of the cathode and separator. In addition to this 3.6 μm/mAh displacement, continuous mossy Li build-up on the anode causes an irreversible drift of the assembly, which is similar to 11.3 μm/cycle. Furthermore, our data indicate significant lithiation gradients in the NMC811 cathode during the oxide relithiation, which is not observed during the delithiation.

25 ENERGY STORAGE↗
DOE OSTI2024

High‐throughput combinatorial approach expedites the synthesis of a lead‐free relaxor ferroelectric system

Abstract Developing novel lead‐free ferroelectric materials is crucial for next‐generation microelectronic technologies that are energy efficient and environment friendly. However, materials discovery and property optimization are typically time‐consuming due to the limited throughput of traditional synthesis methods. In this work, we use a high‐throughput combinatorial synthesis approach to fabricate lead‐free ferroelectric superlattices and solid solutions of (Ba 0.7 Ca 0.3 )TiO 3 (BCT) and Ba(Zr 0.2 Ti 0.8 )O 3 (BZT) phases with continuous variation of composition and layer thickness. High‐resolution x‐ray diffraction (XRD) and analytical scanning transmission electron microscopy (STEM) demonstrate high film quality and well‐controlled compositional gradients. Ferroelectric and dielectric property measurements identify the “optimal property point” achieved at the composition of 48BZT–52BCT. Displacement vector maps reveal that ferroelectric domain sizes are tunable by varying {BCT–BZT} N superlattice geometry. This high‐throughput synthesis approach can be applied to many other material systems to expedite new materials discovery and properties optimization, allowing for the exploration of a large area of phase space within a single growth. image

36 MATERIALS SCIENCE↗
DOE OSTI2020

Shear Behavior of Artificial Clay Seams within Bedded Salt Structures

Bedded salt contains thin layers of clay, also known as clay seams, in-between far thicker layers of salt. These inhomogeneities are thought to have first-order effects on the closure of nearby drifts and potential roof collapses. Despite their importance, characterizations of the peak shear strength and residual shear strength of clay seams in salt are extremely rare in the published literature. A previous paper reported results from laboratory direct shear experiments on clay seam samples from the Permian Basin in New Mexico. These clay seams behaved similar to intact salt, which was attributed to the abundance of salt crystals intersecting the clay seams. None of those specimens contained a distinct ¼" - ½" (6 -12 mm) thick clay seam, as has been observed in drifts at the Waste Isolation Pilot Plant (WIPP). Due to the difficulty in obtaining WIPP samples with these types of clay seams, artificial seams of bentonite and brine sandwiched between sections of salt were created and shear tested. Eight 4" diameter samples were created with either a ¼" or ½" a thick seam and then consolidated at 3000 psi prior to shear testing. The direct shear tests on these samples were performed at nominal normal stresses representative of expected WIPP in-situ conditions (500 to 1500 psi). The resulting shear stress vs. shear displacement curves exhibited a peak followed by a gradual decay of shear strength. The shear stress never transitioned to a true residual shear stress plateau, so the final shear strength at the end of each test (0.75" of shear displacement) was analyzed instead. Both the peak shear strength and the final shear strength conformed to Mohr- Coulomb behavior with friction angles and cohesion strengths consistent with a saturated, highly consolidated, clay. These new artificial clay seam results and the previous clay-interspersed-with-salt results likely bound the expected shear behavior of WIPP clay seams.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

High-throughput combinatorial approach expedites the synthesis of a lead-free relaxor ferroelectric system

Developing novel lead-free ferroelectric materials is crucial for next-generation microelectronic technologies that are energy efficient and environment friendly. However, materials discovery and property optimization are typically time-consuming due to the limited throughput of traditional synthesis methods. In this work, we use a high-throughput combinatorial synthesis approach to fabricate lead-free ferroelectric superlattices and solid solutions of (Ba 0.7 Ca 0.3 )TiO 3 (BCT) and Ba(Zr 0.2 Ti 0.8 )O 3 (BZT) phases with continuous variation of composition and layer thickness. High-resolution x-ray diffraction (XRD) and analytical scanning transmission electron microscopy (STEM) demonstrate high film quality and well-controlled compositional gradients. Ferroelectric and dielectric property measurements identify the “optimal property point” achieved at the composition of 48BZT–52BCT. Displacement vector maps reveal that ferroelectric domain sizes are tunable by varying {BCT–BZT} N superlattice geometry. This high-throughput synthesis approach can be applied to many other material systems to expedite new materials discovery and properties optimization, allowing for the exploration of a large area of phase space within a single growth.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Directing the adsorption and assembly of laponite nano-discs at oil–water interfaces

Achieving tunable controls on the adsorption and self-assembly of nanoscale building blocks at immiscible fluid interfaces is essential for synthesizing advanced materials, stabilizing emulsions, and the sustainable storage and recovery of fluids. Although extensive efforts have been directed toward resolving the assembly of spherical nanoparticles at water–hydrocarbon interfaces, 2D nanoparticles have received far less attention. In this study, we developed novel controls to direct the adsorption and assembly of 2D laponite nano-discs (diameter = ∼30 nm and thickness = ∼1 nm) at water–heptane interfaces using traces of sodium dodecyl sulfate (SDS) surfactant, demonstrated by advanced in situ small-angle X-ray scattering, atomic force microscopy, spinning drop tensiometer measurements and molecular dynamics simulations. The results show that SDS surfactant displaces the adsorbed laponite nano-discs from the interface toward the aqueous phase. The extent of this displacement increases with SDS concentration such that high SDS concentrations convert laponite-rich interfaces to SDS-rich interfaces free of laponite nano-discs. This transformation is associated with significant alterations in the rheological and nanomechanical properties of the host interface. In this context, reduction in interfacial tension and interfacial stiffness and an increase in the interfacial deformation is observed on increasing the SDS concentration from 0 to 0.1 wt%. The displacement of laponite nano-discs from the interface is driven by strong electrostatic interactions between the hydrophilic SDS group and interfacial water molecules. These studies unlock new insights into the adsorption and assembly of 2D nanoscale particles at water–hydrocarbons interfaces that are relevant for various applications related to energy and environmental science and engineering.

interfacial tension↗
DOE OSTI2026

Assembly Bowing Reactivity Calculation Methodology Applied to Lead Fast Reactor

Ducted assemblies bow during operation due to power and temperature gradients which can be influenced by operating flow rates. For fast spectrum cores using ducted assemblies, the bowing behavior follows that of the duct and because there are gaps between the ducts, the bowing can result in compaction or expansion of the active core. This local displacement can have a positive or negative impact and knowing the net effect during transients is important for system reactivity control. Keeping the net bowing reactivity worth low is possible with attentive placement of load pads above the active core and selecting load pad gap thicknesses that result in a desired behavior at standard operating conditions. This paper considers a Lead Fast Reactor (LFR) concept fueled by HALEU UO2 developed by Westinghouse Electric Company (WEC) and applies a workflow of Argonne-developed codes to estimate the core bowing reactivity worth. Using orifice flow rates grouped by assembly type, the net reactivity impact due to core assembly bowing for the LFR was found to be small and in line with other liquid metal fast reactors: +29/+32/+35 pcm, or about +$0.049/+$0.055/+$0.059, for BOEC/MOEC/EOEC, respectively.

bowing reactivity↗
DOE OSTI2025

Factors controlling injection-induced rupture of intersecting faults during geological sequestration of CO 2

This study addresses coupled multiphase fluid flow and geomechanics effects on potential fault activation associated with subsurface CO 2 injection around intersecting faults. An enhanced fault-representation model is used to capture geomechanical responses of two intersecting faults with finite length during CO 2 injection. The faults are embedded in a strike-slip stress regime of a caprock-reservoir-basement system with the faults represented by zero-thickness interfaces with adjacent finite-thickness damage zones. A sensitivity analysis is conducted to study the effect of fault permeability, slip-weakening behavior, well location relative to the orientation of faults, and well placement (the number and location of injection wells). Five metrics (pressure, CO 2 plume, shear state on the fault, as well as shear displacement and stress path at selected fault monitoring points) are selected to assess CO 2 migration and reactivation of intersecting faults. The results show that induced ruptures are favored by low permeability faults due to high pressure buildup and by slip-weakening behavior resulting from fault strength reduction. The location of one injection well relative to fault orientation determines the magnitude of changes in effective normal stress and shear stress, affecting the location of induced ruptures. Well placement (two injection wells used in the paper) dominates pressure diffusion around the intersection and tips of faults. This redistributes changes in effective normal stress caused by each injection well, influencing the spatial distribution of ruptures along faults. A larger injection volume induces far-field ruptures that are controlled by stress transfer within the injection layer. The findings presented here can provide valuable insights into engineering operations for a long-term, safe, and reliable geologic CO 2 storage.

Fault permeability↗
DOE OSTI2026

Crystal Orientation Independent Strong TERS Response in Anisotropic ReS2 on Gold

Rhenium disulfide (ReS2) crystallizes in a distorted 1T' lattice with triclinic symmetry arising from Re–Re dimerization, which produces in-plane anisotropic properties and a dense set of Raman-active modes with mixed atomic displacements. Unlike far-field Raman spectroscopy, which shows strong polarization and orientation dependence, tip-enhanced Raman spectroscopy (TERS) probes out-of-plane Raman tensor components. Here we use 785 nm (1.58 eV) gap-mode TERS to investigate monolayer to four-layer thick ReS2 crystals.. TERS maps and averaged spectra reveal that all modes remain invariant under 90° rotation of the crystal, and the only thickness-dependent feature is the emergence of the multilayer breathing mode. These results demonstrate that TERS yields a crystal-orientation-independent Raman response in ReS2 and provides direct access to Raman tensor components that are not easily accessible in conventional far-field measurements.

Valencia Acuna, Pavel A.↗
DOE OSTI2021

Prediction of Aluminum to Steel RSW Joint Failure (CRADA 405)

General Motors, LLC has developed a resistance spot welding process to join aluminum sheet to steel for body-in-white manufacturing. Efforts to develop the process for any one joint configuration (combination of alloy and thicknesses) is intensive. To aid in process understanding and eventual reduction in process development efforts, an initiative was created to develop an finite element model of the various destructive test configurations (lap shear, cross-tension, and coach peel) to help predict the failure mode and load displacement curves under tensile testing. This report describes the finite element modeling approach, the means by which local material properties were determined, as well as model validation and refinement efforts.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Low-frequency Raman spectrum of 2D layered perovskites: Local atomistic motion or superlattice modes?

We report the low-frequency Raman spectrum (ω = 10 cm -1 –150 cm -1 ) of a wide variety of alkylammonium iodide based 2D lead halide perovskites (2D LHPs) as a function of A-site cation (MA = methylammonium and FA = formamidinium), octahedral layer thickness (n = 2–4), organic spacer chain length (butyl-, pentyl-, hexyl-), and sample temperature (T = 77 K–293 K). Using density functional theory calculations under the harmonic approximation for n = 2 BA:MAPbI, we assign several longitudinal/transverse optical phonon modes between 30 cm -1 and 100 cm -1 , the eigen displacements of which are analogous to that observed previously for octahedral twists/distortions in bulk MAPbI. Additionally, we propose an alternative assignment for low-frequency modes below this band (<30 cm -1 ) as zone-folded longitudinal acoustic phonons corresponding to the periodicity of the entire layered structure. Furthermore, we compare measured spectra to predictions of the Rytov elastic continuum model for zone-folded dispersion in layered structures. Our results are consistent across the various 2D LHPs studied herein, with energetic shifts of optical phonons corresponding to microscopic structural differences between materials and energetic shifts of acoustic phonons according to changes in the periodicity and elastic properties of the perovskite/organic subphases. This study highlights the importance of both the local atomic order and the superlattice structure on the vibrational properties of layered 2D materials.

2D materials↗
DOE OSTI2023

Magnetic potential based formulation for linear and non-linear 3D RF sheath simulation

Abstract This paper reports a new numerical scheme to simulate the radio-frequency (RF) induced RF sheath, which is suitable for a large 3D simulation. In the RF sheath boundary model, the tangential component of the electric field ( E t ) is given by the gradient of a scalar electric field potential. We introduce two additional scalar potentials for the tangential components of the magnetic field, which effectively impose the normal electric displacement ( D n ) on the plasma sheath boundary condition via in-homogeneous Neumann boundary condition and constrain the tangential electric field on the surface as curl-free ( ∇ × E t = 0 ). In our approach, the non-linear sheath impedance is formulated as a natural extension of the large thickness (or asymptotic) sheath limit ( D n = 0 ), allowing for handling both asymptotic and non-linear regimes seamlessly. The new scheme is implemented using the Petra-M finite element method analysis framework and is verified with simulations in the literature. The significance of non-linearity is discussed in various plasma conditions. An application of this scheme to asymptotic RF sheath simulation on the WEST ICRF antenna side limiters is also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Revealing Defect-Seeded and Interfacial Generation Mechanisms of Photoinduced Coherent Phonons with 4D Ultrafast Electron Microscopy

Ultrafast photoexcitation of coherent phonons is driven by an impulsive, collective displacement of constituent atoms from their average equilibrium lattice positions [1]. Models describing the generation of coherent acoustic modes typically invoke the creation of an anisotropic strain profile arising from the relatively instantaneous absorption of an ultrafast laser pulse [2]. If the skin depth is shallow relative to the specimen thickness, a steep tensile strain gradient perpendicular to the surface ($\frac{∂ε}{∂z}$) results. Initial relaxation occurs via rapid contraction of the surface layers followed by subsequent coherent oscillations of the lattice and launch of a train of coherent elastic strain waves [i.e., coherent acoustic phonons (CAPs)]. Macroscopically, responses are generally well-described by constitutive relations as gleaned from data gathered using ultrasonic methods or ultrafast spectroscopies. Furthermore, at the atomic to nanoscale level, individual lattice discontinuities and their impact on CAP behaviors can be modeled using multiscale methods [3,4]. Further, average unit-cell level responses on ultrafast timescales can be probed using femtosecond electron and X-ray scattering [5,6].

Flannigan, David J. [University of Minnesota, Minn↗
DOE OSTI2020

Ultralow Voltage Manipulation of Ferromagnetism

Spintronic elements based on spin transfer torque have emerged with potential for on-chip memory, but they suffer from large energy dissipation due to the large current densities required. In contrast, an electric-field-driven magneto-electric storage element can operate with capacitive displacement charge and potentially reach 1-10 µJ cm -2 switching operation. In this paper, magneto-electric switching of a magnetoresistive element is shown, operating at or below 200 mV, with a pathway to get down to 100 mV. A combination of phase detuning is utilized via isovalent La substitution and thickness scaling in multiferroic BiFeO 3 to scale the switching energy density to ≈10 µJ cm -2 . This work provides a template to achieve attojoule-class nonvolatile memories.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Similarities and differences between nickelate and cuprate films grown on a SrTiO 3 substrate

The recent discovery of superconductivity in Sr-doped NdNiO 2 films grown on SrTiO 3 started a novel field within unconventional superconductivity. Therefore, to understand the similarities and differences between nickelate and cuprate layers on the same SrTiO 3 substrate, here based on the density functional theory we have systematically investigated the structural, electronic, and magnetic properties of NdNiO 2 / SrTiO 3 and CaCuO 2 / SrTiO 3 systems. Our results revealed a strong lattice reconstruction in the case of NdNiO 2 / SrTiO 3 , resulting in a polar film, with the surface and interfacial NiO 2 layers presenting opposite displacements. To avoid the “polar catastrophe,” the NiO 2 surface to the vacuum reconstructs as well. However, for CaCuO 2 / SrTiO 3 , the distortions of those same two CuO 2 layers were in the same direction. In addition, we found this distortion to be approximately independent of the studied range of film thickness for the nickelate films. Furthermore, we also observed a two-dimensional electron gas at the interface between NdNiO 2 and SrTiO 3 , caused by the polar discontinuity, in agreement with recent literature. For NdNiO 2 / SrTiO 3 the two-dimensional electron gas extends over several layers, while for CaCuO 2 / SrTiO 3 this electronic rearrangement is very localized at the interface between CaCuO 2 and SrTiO 3 . The electronic reconstruction found at the interface involves a strong occupation of the Ti 3 d x y state. In both cases, there is a significant electronic charge transfer from the surface Ni or Cu layers to the Ti interface layer. The interfacial Ni and Cu layers are hole and electron doped, respectively. By introducing magnetism and electronic correlation, we observed that the d 3 z 2 - r 2 orbital of Ni becomes itinerant while the same orbital for Cu remains doubly occupied, establishing a clear two- vs one-orbital active framework for the description of these systems. Furthermore, we also observed a strong magnetic reconstruction at the NdNiO 2 surface to vacuum layer where magnetism is basically suppressed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗