Search NASA⌕ Search

SEARCH · Search NASA

Results for “distillation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Recovery of terephthalic acid from solar PV backsheets using waste solvent from distilled spirits production

Current research on solar photovoltaic (PV) recycling mainly focuses on recovering valuable metals and glass, often neglecting the polymeric components, particularly the backsheets, which are typically landfilled or thermally decomposed. This study explores an innovative approach to upcycle PV backsheets into value-added products, specifically terephthalic acid (TPA), using waste ethanol solvent from the distilled spirits industry. Experimental results show that increasing both exposure time and ethanol concentration significantly enhances backsheet delamination efficiency. Using waste ethanol, a maximum delamination efficiency of 80% was achieved at room temperature after 24 hours. In decomposition trials, both sodium hydroxide (NaOH) and potassium hydroxide (KOH) demonstrated comparable efficiencies (96.6–97.5%) over 8 and 24 hour reactions. With virgin ethanol, NaOH yielded 94–97.5% TPA recovery. Notably, using waste ethanol achieved a TPA recovery efficiency of 96.8%, underscoring the process's economic viability and sustainability. Analytical characterization of TPA recovered after 8 hours showed consistent spectral patterns across both alkalis and solvents, indicating a similar chemical environment and functional groups. The recovered TPA can be repolymerized into high-purity PET, suitable for manufacturing new PV backsheets. This work advances polymer-recycling by demonstrating that an industrial waste solvent (distilled-spirits ‘heads’) can replace virgin ethanol without loss in delamination performance or TPA yield. While PV backsheet PET is a modest share of global PET, using waste ethanol to upcycle this currently under-recycled stream demonstrates a transferable solvent-reuse pathway that can extend to higher-volume PET sources.

Nain, Preeti [Michigan State Univ., East Lansing, ↗
DOE OSTI2022

Distilling Knowledge from Ensembles of Cluster-Constrained-Attention Multiple-Instance Learners for Whole Slide Image Classification

The peculiar nature of whole slide imaging (WSI), digitizing conventional glass slides to obtain multiple high resolution images which capture microscopic details of a patient’s histopathological features, has garnered increased interest from the computer vision research community over the last two decades. Given the unique computational space and time complexity inherent to gigapixel-size whole slide image data, researchers have proposed novel machine learning algorithms to aid in the performance of diagnostic tasks in clinical pathology. One effective algorithm represents a Whole slide image as a bag of smaller image patches, which can be represented as low-dimension image patch embeddings. Weakly supervised deep-learning methods, such as cluster-constrained-attention multiple instance learning (CLAM), have shown promising results when combined with image patch embeddings. While traditional ensemble classifiers yield improved task performance, such methods come with a steep cost in model complexity. Through knowledge distillation, it is possible to retain some performance improvements from an ensemble, while minimizing costs to model complexity. In this work, we implement a weakly supervised ensemble using clustering-constrained-attention multiple-instance learners (CLAM), which uses attention and instance-level clustering to identify task salient regions and feature extraction in whole slides. By applying logit-based and attention-based knowledge distillation, we show it is possible to retain some performance improvements resulting from the ensemble at zero cost to model complexity.

Alamudun, Folami↗
DOE OSTI2023

Measurement of isotopic separation of argon with the prototype of the cryogenic distillation plant Aria for dark matter searches

The Aria cryogenic distillation plant, located in Sardinia, Italy, is a key component of the DarkSide-20k experimental program for WIMP dark matter searches at the INFN Laboratori Nazionali del Gran Sasso, Italy. Aria is designed to purify the argon, extracted from underground wells in Colorado, USA, and used as the DarkSide-20k target material, to detector-grade quality. In this paper, we report the first measurement of argon isotopic separation by distillation with the 26 m tall Aria prototype. We discuss the measurement of the operating parameters of the column and the observation of the simultaneous separation of the three stable argon isotopes: ${}^{36}\hbox {Ar}$, ${}^{38}\textrm{Ar}$, and ${}^{40}\textrm{Ar}$. We also provide a detailed comparison of the experimental results with commercial process simulation software. This measurement of isotopic separation of argon is a significant achievement for the project, building on the success of the initial demonstration of isotopic separation of nitrogen using the same equipment in 2019.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2023

Efficient and Robust Jet Tagging at the LHC with Knowledge Distillation

The challenging environment of real-time data processing systems at the Large Hadron Collider (LHC) strictly limits the computational complexity of algorithms that can be deployed. For deep learning models, this implies that only models with low computational complexity that have weak inductive bias are feasible. To address this issue, we utilize knowledge distillation to leverage both the performance of large models and the reduced computational complexity of small ones. In this paper, we present an implementation of knowledge distillation, demonstrating an overall boost in the student models' performance for the task of classifying jets at the LHC. Furthermore, by using a teacher model with a strong inductive bias of Lorentz symmetry, we show that we can induce the same inductive bias in the student model which leads to better robustness against arbitrary Lorentz boost.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

A generalized distillation network synthesis model

In this report we propose a generalized superstructure-based distillation network synthesis model with improved modeling capabilities resulting in an extended solution space. The model can assign multiple mixtures to be separated (e.g., reactor network effluents) to different columns of the network while considering the interactions among different separation steps. In terms of outlets, products with general specifications, including pure components and multi-component mixtures, as well as streams without strict specifications (e.g., reactor recycle streams) can be readily handled. Furthermore, stream bypass is considered to avoid unnecessary separations, and thermal coupling is considered to yield novel solutions. The proposed model enables seamless integration with reactor network synthesis models thereby leading to solutions that are superior to the ones obtained by conventional sequential approaches.

42 ENGINEERING↗
DOE OSTI2020

Performance of sweeping gas membrane distillation for treating produced water: Modeling and experiments

Membrane distillation (MD) has shown promise for desalination of produced water (PW), but there are very few studies reported on the performance of MD with real PW and the characteristics of the fouling and scaling in MD. Among different MD configurations, sweeping gas MD (SGMD) is the least studied configuration. Here we report the application of SGMD for treating high-salinity PW (123 g L -1 ). The SGMD operating conditions were first carefully optimized through pure water MD experiments by varying operating conditions. The flux evaluation was accompanied by a detailed Aspen Custom Modeler simulation based on the electrolyte-NRTL thermodynamic model to better understand the heat and mass transfer in the feed and permeate channel. Supported by experiments, modeling results confirmed the partial condensation of the vapor in the permeate channel. Furthermore, it was concluded that the saturation of the sweeping gas is controlling the overall mass transfer through the membrane. Selected membranes and optimized conditions were then used to conduct short-term and long-term performance tests with PW. In long-term MD test, the concentration of the PW increased by a factor of two (50% water recovery), while the membrane exhibited small flux decline. Elemental analysis showed that strontium and sodium were the major scalant compounds.

42 ENGINEERING↗
DOE OSTI2021

Comparative analysis of various pretreatments to mitigate fouling and scaling in membrane distillation

Membrane distillation (MD) has shown strong promise for treating hypersaline produced water (PW) streams. Scaling and fouling on the membrane surface, however, have been identified as major challenges for commercialization and widespread application. The focus of this study was to first identify the nature of foulants and scalants on the membrane surface and then investigate the pretreatment strategies that mitigate the extent of fouling and scaling on the membrane surface. Vacuum MD (VMD) was selected for this study because of its higher flux at more moderate feed temperatures that eventually leads better assessment of fouling and scaling on the membrane surface. VMD flux tests were carried out with three different real PW samples at total dissolved solids concentrations in the range of 120-160 g/L. It was found that an efficient pretreatment prior to MD is required to mitigate the fouling potential of the organic matter, mostly suspended constituents, in PW samples. Suspended organics fouled and quickly wetted the MD membrane. Major conventional treatments, including filtration, oxidation, coagulation, air floatation, and aeration were investigated to pretreat the PW before VMD tests. A comprehensive comparative analysis is presented showing that the ultrafiltration and coagulation pretreatments displayed the best performance in mitigating the fouling and scaling, while oxidative pretreatment was found to be effective in reducing the iron concentration to less than 5 ppm. The surface of scaled membranes was carefully characterized to further evaluate the performance of each pretreatment. The components that had the highest tendency to precipitate on the membrane surface were identified as strontium sulfate, calcium carbonate, sodium chloride, iron oxide, and silica. In closing, these findings are supported by thermodynamic estimation of the saturation index.

42 ENGINEERING↗
DOE OSTI2022

Optimization-based modeling and economic comparison of membrane distillation configurations for application in shale gas produced water treatment

Membrane distillation (MD) is an emerging membrane technology with great potential for treatment of hypersaline wastewater generated by unconventional (shale) oil and gas reservoirs. However, the low energy efficiency of this technology makes the operating cost of MD systems relatively high, especially in the absence of waste heat. There are several MD configurations with inherent advantages and disadvantages and varying performance. As such, there is a need for thermo-economic optimization of MD systems in a systematic manner to assess their economic performance. Here we present an optimization framework to model and compare the performance of six MD configurations (DCMD, AGMD, PGMD, CGMD, SGMD, and VMD) in continuous recirculation mode for treatment of hypersaline wastewater. The optimization results show that AGMD with small gap size operated at low stream Reynolds number outperforms all other configurations with treatment cost of 4.57 US $/m 3 of feed. However, restricting the system design to more practically relevant operating conditions, such as higher Reynolds number and larger gap size, diminishes the cost superiority of AGMD over other configurations. We also observed that treatment cost using PGMD configuration approaches those of CGMD and DCMD, particularly when modules with small gaps are used.

42 ENGINEERING↗
DOE OSTI2022

Comparative techno-economic assessment of osmotically-assisted reverse osmosis and batch-operated vacuum-air-gap membrane distillation for high-salinity water desalination

New developments in pressure- and thermally driven membrane desalination technologies offer the potential to cost-effectively treat high-salinity waters, especially when powered by low-cost solar electricity and thermal energy. This paper presents a comparative techno-economic assessment of the state-of-the-art most promising pressure- and thermally driven membrane technologies for high recovery desalination, namely, osmotically-assisted reverse osmosis (OARO) and batch-operated vacuum-air-gap membrane distillation (batch V-AGMD), to produce potable water while concentrating brine within the range of 140–290 g/L TDS for minimum-liquid-discharge (MLD) and zero-liquid-discharge (ZLD) applications. It is shown that both OARO and batch V-AGMD can treat feedwater and brines with TDS in the range of 30–125 g/L with corresponding fresh water recovery rates of 85–25%. When low cost solar electricity and thermal energy are used, the resulting levelized cost of water (LCOW) from OARO is in the range of 0.70–6.28 $/m 3 , and that from batch-V-AGMD is in the range of 1.74–2.77 $/m 3 . OARO is more cost-effective than batch V-AGMD when feedwater salinity is below 70 g/L and recovery below 75%, whereas batch V-AGMD is more cost-effective at higher recovery rates and salinity levels. Finally, the sensitivity of this comparison on energy prices and module costs is discussed.

42 ENGINEERING↗
DOE OSTI2022

Laboratory and pilot-scale studies of membrane distillation for desalination of produced water from Permian Basin

Substantial quantities of produced water generated during the extraction of oil and gas from unconventional reservoirs present significant environmental concern and increase the operating cost for this industry. Membrane Distillation (MD) can serve as a potential solution for beneficial reuse of produced water by generating high-quality permeate and reducing the volume of produced water requiring disposal. This study investigated treatment of produced water from Permian Basin in both laboratory and pilot-scale studies. Laboratory tests revealed the potential to successfully recover 50% of produced water although some increase in permeate conductivity was observed due to the passage of ammonia from the feed side. Initial pilot-scale test with filtration of raw produced water as the only pre-treatment step led to precipitation of SrSO 4 , NaCl, and Fe in the system once the solubility limits for these salts were exceeded. However, chemical pretreatment that included pH adjustment, aeration, and barite precipitation, allowed successful steady-state operation of the AGMD pilot system for 5 days where the produced water was concentrated from 127 g/L to 255 g/L (~50% water recovery) while recovering high quality permeate. Overall, greater than 99.7 % salt rejection was achieved with the average permeate flux of 1.86 LMH. Finally, mass balance analysis suggested potential Ba and Ca precipitation in the system but there was no impact on AGMD performance and permeate quality during 5 days of continuous operation in the field.

42 ENGINEERING↗
DOE OSTI2022

Optimization-based technoeconomic comparison of multi-stage membrane distillation configurations for hypersaline produced water desalination

Unconventional oil and gas production raises concerns regarding sustainable management of high salinity wastewaters generated in this process. Membrane distillation (MD) is a thermal desalination process capable of treating hypersaline brines such as produced water. The low single pass recovery in MD systems operated in a single stage requires a large recycle stream to achieve the desired recovery, resulting in high energy consumption and operating cost. Multistage configurations in continuous recirculation operation mode offer the potential to reduce the energy intensity of MD systems. However, rigorous analysis is needed to assess the performance of MD configurations when operating in multi-stage mode. Here, we present an optimization-based comparison of economic and energetic performance for five configurations of MD (including DCMD, AGMD, PGMD, CGMD, and VMD) operating in multi-stage continuous recirculation mode. Our findings demonstrate that multistage operation reduces the treatment cost and energy intensity of all MD configurations compared to single stage MD, with the greatest benefit for VMD and PGMD. AGMD with five stages outperforms other configurations with 3.58 $/m 3 feed treatment cost, followed by VMD, CGMD, DCMD, and PGMD with 3.8, 4.2, 5.4, and 9.06$/m 3 feed treatment costs corresponding to twelve, eight, eight, and sixteen stages, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Combined chlorine dioxide–membrane distillation for the treatment of produced water

Membrane distillation (MD) is a promising technique for desalinating hypersaline brine, such as produced water (PW). To date, fouling and scaling have remained as major challenges for MD implementation. In this study, chlorine dioxide combined with induced air floatation (ClO 2 -IAF) was systematically investigated as a pretreatment prior to MD. First, the ClO 2 generation based on sodium chlorite and hydrochloric acid was optimized to maximize the on-demand ClO 2 production. The maximum production yield of 18.4% was obtained with 4wt.% NaClO 2 and 20wt.% HCl solutions, with a molar ratio of 1:1.25. Then, two real PW samples were pretreated, and removal efficiencies for total suspended solids (TSS), turbidity, iron, and total organic carbon (TOC) were comprehensively studied by varying the ClO 2 dosage between 6 and 91 mg/L. The ClO 2 -IAF pretreatment displayed TSS and turbidity removals above 90% and TOC removal close to 55%. Further, the PW constituents such as benzene, toluene, ethylbenzene, xylene (BTEX), and total petroleum hydrocarbons (TPH) were analyzed and quantified throughout the cascade of the treatments. The volatiles like BTEX were mainly removed by air floatation, while saturated hydrocarbons such as TPH were retained by the hydrophobic membrane. The MD long-term stability without any in-place cleaning was evaluated, and the membrane withstood for twenty two days without wetting, suggesting that optimizing oxidation pretreatment is critical for mitigating the fouling in MD. Results suggest that organic fouling in PW could be effectively reduced by the pretreatment, but further treatment is required to mitigate the scaling, which resulted in MD wetting.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Fouling characterization and treatment of water reuse concentrate with membrane distillation: Do organics really matter

Membrane distillation (MD) for the treatment of concentrated brines has been limited in part by membrane fouling, resulting in subsequent flux decline and membrane wetting. This study provides new insight into the identification of fouling and scaling mechanisms and pretreatment strategies for mitigating flux decline with MD treatment of water reuse reverse osmosis concentrate (ROC). Bench-scale direct contact MD experiments were performed with untreated and pretreated ROC. Biological activated carbon (BAC), chemical water softening, or fluidized bed crystallization reactor coupled with ion exchange (FBCR-IX) were selected as pretreatment strategies to isolate the effects of organic fouling and calcium scaling. Organic and inorganic compounds were analyzed by high-performance liquid chromatography (HPLC) and inductively coupled plasma mass spectrometry (ICP-MS). Calcium ions were found to be the major contributor to flux decline despite the high organic content in the ROC. Minimal organic fouling is likely because the organic matter in the ROC is hydrophilic, limiting hydrophobic-hydrophobic interactions between the organics and the membrane. Furthermore, the water flux declined by 63 % after removing organic compounds by BAC pretreatment, with 60 % of the calcium mass precipitating from the solution. Whereas, the water flux remained constant after removing multivalent ions with fluidized bed crystallization. Cleaning the membrane by acid washing and temperature reversal recovered 73 % and 12 % of the water flux, respectively. The analyses outlined in this study can assist in selecting appropriate fouling and scaling mitigation strategies for water reuse ROC and a wide range of feed solutions used in MD applications.

42 ENGINEERING↗
DOE OSTI2020

Cost optimization of high recovery single stage gap membrane distillation

Estimating the cost of membrane distillation (MD) processes at scale is confounded by the vast array of possible process configurations, module configurations, and operating conditions and the extreme sensitivity of MD costs to these parameters. This work develops a comprehensive MD cost optimization framework for minimizing the levelized cost of water (LCOW) as a function of feed salinity and temperature. Our single stage gap MD model fully captures solution properties, heat transfer, and mass transfer relationships in the modules to determine the cost optimal design as a function of multiple decision variables, including process configuration (feed location and connectivity between the hot and cold-side), the gap type (air, permeate, conductive), equipment sizes (membrane, heater, chiller, and heat exchanger units), and operating conditions (flow rates, hot and cold side temperatures, and heating and cooling duties). We estimate that the minimum LCOW of conductive gap MD ranges between $\$$10 and $\$$16 per m 3 for feed salinities of 25 g/L to 200 g/L and water recoveries of 30%–75%. Further, we update several heuristic assumptions for cost optimal system operation, including: increased thermal conductivity of the gap decreases system costs; cost optimal MD operates at the highest allowable temperature; and the LCOW is a strong function of brine salinity. Finally, we find that improving membrane properties and lowering heating and cooling costs will provide only modest reductions in costs (<25%).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Life-cycle energy use and greenhouse gas emissions of palm fatty acid distillate derived renewable diesel

This study aims to quantify life-cycle fossil energy use and greenhouse gas (GHG) emissions for palm fatty acid distillate (PFAD) derived renewable diesel (RD) taking into consideration different feedstock classifications that are applicable to PFAD (residue, byproduct, or coproduct), and incorporating updated data for key processes. Under the three classifications, the PFAD to RD pathway was modeled using the Greenhouse gases, Regulated Emissions, and Energy Use in Technologies (GREET®) model. PFAD-derived RD could reduce fossil energy consumption by 77%–88%, relative to petroleum diesel. GHG emissions are very sensitive to PFAD classification and coproduct handling methods. Considering the production of palm oil and PFAD and economic value, we maintain that PFAD should be treated as a byproduct in palm oil refineries. With this treatment, PFAD-derived RD could achieve 84% GHG emissions reductions, compared to the emissions of petroleum diesel. We also employed a substitution method to address the substitution of PFAD by other materials in the marketplace. Compared to coproduct allocation results, we found substituting PFAD by tallow, soy oil, barley, and canola oil results in lower GHG emissions. Due to high induced land-use change emissions associated with palm farming, if PFAD is treated as a coproduct with refined palm oil, PFAD-derived RD may not deliver GHG reductions. A sensitivity analysis identified key parameters such as palm fruit yield, oil extraction efficiency in oil mills, and energy use intensity for RD production affects LCA results significantly; future efforts to improve these parameters could result in further GHG reductions.

09 BIOMASS FUELS↗
DOE OSTI2021

Molecular thermodynamics for scaling prediction: Case of membrane distillation

Membrane distillation (MD) for water treatment is significantly impaired by the scaling of dissolved minerals. The type and content of minerals generally measured as total dissolved solids (TDS) in hypersaline brines not only reduce the MD flux but also control the scaling behavior on the membrane surface. The scaling-induced pore blockage further reduces water flux and eventually leads to membrane wetting. The scaling problem is even more pronounced in the treatment of produced water (PW) as it contains 3–7 times higher TDS concentrations, compared to seawater. Theoretically, the necessary conditions for a salt to precipitate can be traced from its solubility product constant and activity of the constituents within the solution. Therefore, a comprehensive thermodynamic model is necessary to represent the electrolyte behavior and to predict the precipitation of different salts in a complex solution like PW. We pursued electrolyte Nonrandom Two Liquid Theory (eNRTL), a state-of-the-art electrolyte model, to address the PW fluid phase equilibria. With a fully parameterized eNRTL model, we predicted salt precipitations in two different PW samples and compared the results against the experimental findings. Furthermore, here we forecast the precipitation of salts in response to the change in PW concentration and temperature in the MD operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Energy and exergy analysis of multi-stage vacuum membrane distillation integrated with mechanical vapor compression

Membrane distillation (MD) is a promising candidate for desalinating hypersaline brine, but its poor energy efficiency has remained a major barrier for widespread application. One possible solution to this issue is to recover the latent heat in the process. In this work, a multi-stage vacuum MD (MSVMD) was integrated with a mechanical vapor compressor (MVC) to enhance the latent heat recovery, and the energetic and exergetic performance of this integrated process was examined. A comprehensive energy and exergy analysis is provided to compare MSVMD and MSVMD-MVC processes for desalination of hypersaline brine. This analysis was conducted by examining the effect of the compression ratio on the energetic and exergetic performance, and the findings are reported in terms of specific thermal energy consumption (STEC), specific electricity consumption (SEC), and exergetic efficiency. The energy analysis shows that thermal energy consumption can be reduced as the compression ratio increases, due to the enhancement of latent heat recovery. The MSVMD-MVC process can be operated in a steady-state condition, without the need for thermal heat input; with STEC and SEC of 0 and 49 kWh/m 3 at the feed temperature of 50 °C and MVC compression ratio of 2.14. Moreover, exergy analysis demonstrates the efficacy of the eNRTL model in exergy calculation. Exergy destruction can be greatly reduced by increasing the compression ratio to an optimal value. For high salinity brine (124 g/L), MSVMD-MVC achieved a higher exergetic efficiency of 6.85%, compared to 2.42% in MSVMD. Furthermore, the result suggests that the application of MVC can intensify the energy efficiency and exergetic efficiency of the MSVMD system, although this process cannot outperform the current desalination technologies from the standard primary energy point of view.

42 ENGINEERING↗
DOE OSTI2023

Understanding flow dynamics in membrane distillation: Effects of reactor design on polarization

Optimization and design of full-scale membrane distillation (MD) systems usually require Sherwood and Nusselt correlations that are developed from lab-scale systems. However, entrance effects in lab-scale systems can significantly impact heat, mass and momentum transfer in the reactor, therefore affect the accuracy of the developed experimental Sherwood and Nusselt correlations. Here, Computational Fluid Dynamics (CFD) simulations using OpenFOAM are performed to understand the effects of right-angled bends and inlet design on flow dynamics, temperature and concentration polarization in MD systems. Simulation results show that the presence of right-angled bends and inlets with sudden expansions lead to the formation of Dean vortices. Dean vortices enhance perpendicular mixing in MD systems and reduce both temperature and concentration polarization. Temperature and concentration polarization coefficients in MD systems with right-angled bends and inlets with sudden expansions vary significantly for the same volumetric flow rate. Our studies show that lab-scale systems with the same volumetric flow rate but different designs lead to significantly different Nusselt and Sherwood correlations. Here, this study demonstrates the importance of CFD-informed design of lab-scale systems to minimize entrance effects and suppress Dean vortices for consistent model development and calibration across multiple scales.

42 ENGINEERING↗