Search NASA⌕ Search

SEARCH · Search NASA

Results for “drag modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Hypersonic and planetary entry flight mechanics

The book treats hypersonic flight trajectories and atmospheric entry flight mechanics in light of their importance for space shuttle entry. Following a review of the structures of planetary atmospheres and aerodynamic forces, equations are derived for flight over a spherical planet, and the performance of long-range hypervelocity vehicles in extra-atmospheric flight is analyzed. Consideration is then given to vehicle trajectories in the powered and atmospheric reentry phases of flight, and several first-order solutions are derived for various planetary entry situations. The second-order theory of Loh for entry trajectories is presented along with the classical theories of Yaroshevskii and Chapman for entry into planetary atmospheres, and the thermal problems encountered in hypersonic flight are analyzed. A unified theory for entry into planetary atmospheres is then introduced which allows the performance of a general type of lifting vehicle to be studied, and applied to the analysis of orbit contraction due to atmospheric drag, flight with lift modulation and lateral maneuvers.

Vinh, N. X.↗
NASA NTRS1977

Effect of an integrated scramjet installation on the subsonic performance of an aircraft designed to Mach 6 cruise

Various factors contributing to the high drag caused by the installation of a six-module scramjet engine were determined from wind tunnel tests at Mach numbers from 0.2 to 0.7. Methods for alleviating this drag were also explored. The external exhaust nozzle, required for good cruise performance, was a major contributor. Of the drag produced by the engine modules, a significant fraction was attributable to wall divergence in the combustor. Good drag simulation could be achieved by using a single fuel injection strut having approximately the same cross-sectional area as the three used on the full-scale engine. External exhaust nozzle fences had a small but beneficial effect on maximum L/D and a flap which diverted the flow away from the inlet was effective in decreasing drag but only at low angles of attack.

Johnston, P. J.↗
NASA NTRS2013

Supersonic Aerodynamic Characteristics of Blunt Body Trim Tab Configurations

Trim tabs are aerodynamic control surfaces that can allow an entry vehicle to meet aerodynamic performance requirements while reducing or eliminating the use of ballast mass and providing a capability to modulate the lift-to-drag ratio during entry. Force and moment data were obtained on 38 unique, blunt body trim tab configurations in the NASA Langley Research Center Unitary Plan Wind Tunnel. The data were used to parametrically assess the supersonic aerodynamic performance of trim tabs and to understand the influence of tab area, cant angle, and aspect ratio. Across the range of conditions tested (Mach numbers of 2.5, 3.5, and 4.5; angles of attack from -4deg to +20deg; angles of sideslip from 0deg to +8deg), the effects of varying tab area and tab cant angle were found to be much more significant than effects from varying tab aspect ratio. Aerodynamic characteristics exhibited variation with Mach number and forebody geometry over the range of conditions tested. Overall, the results demonstrate that trim tabs are a viable approach to satisfy aerodynamic performance requirements of blunt body entry vehicles with minimal ballast mass. For a 70deg sphere-cone, a tab with 3% area of the forebody and canted approximately 35deg with no ballast mass was found to give the same trim aerodynamics as a baseline model with ballast mass that was 5% of the total entry mass.

Korzun, Ashley M.↗
NASA NTRSDate not supplied

Jig Twist Optimization of Mach 0.8 Transonic Truss-Braced Wing Aircraft

This paper presents a jig twist optimization study of Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft using FUN3D. The solver has been validated against wind tunnel test data. An aeroelastic model deformation correction method is developed for the wind tunnel model to improve the validation. The flight condition corresponding to Mach 0.8 and design lift coefficient 0.695 is selected for the TTBW aircraft jig twist optimization to reduce the drag coefficient. The static aeroelastic simulation module in FUN3D is used for the aeroelastic simulation. Three different orders of the Chebyshev polynomials are used as shape function to represent the variations of the jig twist distribution along the wing span. The preliminary optimization results show that the Mach 0.8 TTBW aircraft with the optimized jig twist achieves a drag reduction of about 5.7 counts at the design condition when 5 𝑡ℎ order Chebyshev polynomials are used as shape function.

TTBW↗
NASA NTRS1992

Aerodynamics of the advanced launch system (ALS) propulsion and avionics (P/A) module

This paper discusses the design and testing of candidate Advanced Launch System (ALS) Propulsion and Avionics (P/A) Module configurations. The P/A Module is a key element of future launch systems because it is essential to the recovery and reuse of high-value propulsion and avionics hardware. The ALS approach involves landing of first stage (booster) and/or second stage (core) P/A modules near the launch site to minimize logistics and refurbishment cost. The key issue addressed herein is the aerodynamic design of the P/A module, including the stability characteristics and the lift-to-drag (L/D) performance required to achieve the necessary landing guidance accuracy. The reference P/A module configuration was found to be statically stable for the desired flight regime, to provide adequate L/D for targeting, and to have effective modulation of the L/D performance using a body flap. The hypersonic aerodynamic trends for nose corner radius, boattail angle and body flap deflections were consistent with pretest predictions. However, the levels for the L/D and axial force for hypersonic Mach numbers were overpredicted by impact theories.

Ferguson, Stan↗
NASA NTRS1984

Design and performance analysis of a conical-aerobrake, orbital-transfer vehicle concept

A Shuttle-compatible systems design based on the core concept of attachable modules for the major vehicle components is proposed. The principal features include a disposable cargo/extra-propellant tank module; a porous, radiative, backscattering drag-brake surface material of thin silica cloth; and a lightweight carbon-composite support structure. The mission payload capability for delivery, retrieval, and combined operations is determined for a broad range of missions including NASA/DOD requirements and extending through cis-lunar space. The effects of finite-rate surface catalysis, negative lift, and multiple atmospheric passes in reducing the aerothermal heating rates are also investigated. In addition, the structural and thermal-protection problems of the drag-brake support apparatus are analyzed and recommendations are proposed for future design refinements.

Menees, G. P.↗
NASA NTRS2017

Application of an Optimal Control Allocation Scheme with Structural Load and Aero Heating Feedback for a Morphing Inflatable Aerodynamic Decelerator

Precision landing of large payloads on Mars presents a challenge to the Entry, Descent, and Landing (EDL) community. Previous studies indicated that by incorporating the capability for a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) to morph during reentry would result in a more accurate landing footprint by allowing modulation of the lift- to-drag (L/D) vector directly instead of through bank angle control. However, morphing the HIAD shape for trajectory control may expose the HIAD to potential structural loads or aero heating concerns. In this study, the application of an optimal control allocation (OCA) technique was investigated that would to enable the morphing HIAD to maximize trajectory control capabilities while simultaneously keeping the structural loads and aero heating below some thresholds. This concept was demonstrated in a 3 degree-of-freedom (DOF) EDL simulation and provides basis for future research.

Bassett, George Z.↗
NASA NTRS1976

Behavior of aircraft antiskid braking systems on dry and wet runway surfaces - A velocity-rate-controlled, pressure-bias-modulated system

During maximum braking the average ratio of drag-force friction coefficient developed by the antiskid system to maximum drag-force friction coefficient available at the tire/runway interface was higher on dry surfaces than on wet surfaces. The gross stopping power generated by the brake system on the dry surface was more than twice that obtained on the wet surfaces. With maximum braking applied, the average ratio of side-force friction coefficient developed by the tire under antiskid control to maximum side-force friction available at the tire/runway interface of a free-rolling yawed tire was shown to decrease with increasing yaw angle. Braking reduced the side-force friction coefficient on a dry surface by 75 percent as the wheel slip ratio was increased to 0.3; on a flooded surface the coefficient dropped to near zero for the same slip ratio. Locked wheel skids were observed when the tire encountered a runway surface transition from dry to flooded, due in part to the response time required for the system to sense abrupt changes in the runway friction; however, the antiskid system quickly responded by reducing brake pressure and cycling normally during the remainder of the run on the flooded surface.

Stubbs, S. M.↗
NASA NTRS1999

Entry Guidance for the Reusable Launch Vehicle

The X-33 Advanced Technology Demonstrator is a half-scale prototype developed to test the key technologies needed for a full-scale single-stage reusable launch vehicle (RLV). The X-33 is a suborbital vehicle that will be launched vertically, and land horizontally. The goals of this research were to develop an alternate entry guidance scheme for the X-33 in parallel to the actual X-33 entry guidance algorithms, provide comparative and complementary study, and identify potential new ways to improve entry guidance performance. Toward these goals, the nominal entry trajectory is defined by a piecewise linear drag-acceleration-versus-energy profile, which is in turn obtained by the solution of a semi-analytical parameter optimization problem. The closed-loop guidance is accomplished by tracking the nominal drag profile with primarily bank-angle modulation on-board. The bank-angle is commanded by a single full-envelope nonlinear trajectory control law. Near the end of the entry flight, the guidance logic is switched to heading control in order to meet strict conditions at the terminal area energy management interface. Two methods, one on ground-track control and the other on heading control, were proposed and examined for this phase of entry guidance where lateral control is emphasized. Trajectory dispersion studies were performed to evaluate the effectiveness of the entry guidance algorithms against a number of uncertainties including those in propulsion system, atmospheric properties, winds, aerodynamics, and propellant loading. Finally, a new trajectory-regulation method is introduced at the end as a promising precision entry guidance method. The guidance principle is very different and preliminary application in X-33 entry guidance simulation showed high precision that is difficult to achieve by existing methods.

Lu, Ping↗
NASA NTRS1986

Propulsion apparatus and method using boil-off gas from a cryogenic liquid

A propulsion system and method are disclosed for controlling the attitude and drag of a space vehicle. A helium dewar contains liquid helium which cools an experiment package. The helium is heated or vented to keep the temperature between 1.5 and 1.7 degrees K to maintain adequate helium boil-off gas as a propellant without adversely affecting the experiment package which is contained in the helium dewar for protection from solar heating. The apparatus includes auxiliary heater and temperature sensor for controlling the temperature of the helium. The boil-off gas propellant is delivered to thruster modules to control vehicle attutude and compensate for drag.

Blount, D. H.↗
NASA NTRS1985

Design and Performance Analysis of a Conical Aerobrake Orbital Transfer Vehicle Concept

A Shuttle-compatible systems design based on the core concept of attachable modules for the major vehicle components is proposed. The principal features include a disposable cargo/extra-propellant tank module; a porous, radiative, back-scattering drag-brake surface material of thin silica cloth; and a lightweight carbon-composite support structure. The mission payload capability for delivery, retrieval, and combined operations is determined for a broad range of missions including NASA/DOD requirements and extending through cislunar space. The effects of finite-rate surface catalysis, negative lift, and multiple atmospheric passes in reducing the aerothermodynamic heating rates are also investigated. In addition, the structural and thermal protection problems of the drag-brake support apparatus are analyzed, and recommendations are proposed for future design refinements.

Menees, Gene P.↗
NASA NTRS1993

Mountain-wave drag in the stratosphere and mesosphere inferred from observed winds and a simple mountain-wave parameterization scheme

A daily analysis of mountain-wave propagation through observed, global wind, and temperature fields in January and August is presented. Winds and temperatures are obtained from the daily 18-level NMC Climate Analysis Center. Mountain-wave properties are deduced from a simple, gravity wave parameterization scheme in which the effects of topographic anisotropy (ridge orientation) are explicitly included. Planetary waves in the northern winter stratosphere are found to play an important role in modulating the magnitude and distribution of inferred mountain-wave drag in the middle atmosphere. The Aleutian anticyclone is found to effectively block mountain waves generated over western North America from reaching the mesosphere by inducing local mountain-wave-critical levels in the stratosphere. Stratospheric sudden warmings have a similar effect at all longitudes so that during months with sudden warmings the average inferred drag in the mesosphere is reduced by a factor of 4 to 5 from its normal value. Partly as a consequence of larger planetary-wave filtering in the Northern Hemisphere, inferred mountain-wave drag in the southern winter mesosphere is found to be comparable to that in the northern winter mesosphere. Almost all of the mountain wave drag exerted on the southern middle atmosphere is found to originate over the southern Andes and Antarctic Peninsula.

Bacmeister, Julio T.↗
NASA NTRS1980

To encounter a star - The Solar Probe mission

Trajectory and technology requirements for the Solar Probe mission, whereby a spacecraft will attain a perihelion of a few solar radii, are discussed. Planetary gravity assist trajectories are considered that use Jupiter and possibly the earth, and that are needed for large payloads to be carried. Hardware technology development includes a lightweight thermal shield, a high energy propulsion module, and new power generation capability. Also discussed are a drag compensation system making the spacecraft drag free to a level of 10 to the -10th g, and a telecommunications system with doppler tracking accuracy of 0.1 mm/sec.

Randolph, J. E.↗
NASA NTRS1985

The atmospheric heat source over the Tibetan plateau May-August 1979

Estimates of the time and space variability of the atmospheric heat source over Tibet are presented for the summer of 1979. These estimates rely on new data from the People's Republic of China allowing a better assessment of the surface heat fluxes, and on new satellite data from Nimbus-7 giving the radiation balance at the top of the atmosphere. The estimates of the atmospheric heat source turned out to be considerably smaller than those provided earlier in the literature, mainly because of different assumptions of the drag coefficient. The atmospheric heat source over Tibet is mainly modulated by the release of latent heat. Over the southeastern and southwestern plateau regions the heat source appears to be in phase with the precipitation yield of the Indian summer monsoon, whereas central Tibet reveals an out-of-phase behavior. Over western Tibet there appears to be hardly any net import of moisture from outside the region, whereas the maintenance of the hydrological cycle over eastern Tibet requires moisture flux convergence from outside the region of up to 40 percent of the mean rainfall, in agreement with what is known about the surface hydrology of Tibet.

Chen, L.↗
NASA NTRS1976

Low-G fluid transfer technology study

Technology gaps and system characteristics critical to cryogenic and noncryogenic in-orbit fluid transfer were identified. Four different supply systems were conceptually designed as space shuttle payloads. These were; (1) space tug supply - LH2, LO2, N2H4, He - linear acceleration for liquid acquisition with supply module and tug separated from shuttle, (2) tug supply using orbiter drag, (3) orbiter supply - N2O4,MMH,He, H2,O2 - surface tension screens, (4) multiple receivers supply 0 solar electric propulsion stage, Hg, diaphragm - HEAO B, HEe, paddle fluid rotation-satellite control section, N2H4, screens. It was found that screens had the best overall potential for low weight and simplicity, however, thermal problems with cryogenics still need final resolution.

Stark, J. A.↗
NASA NTRS1997

The endomembrane sheath: a key structure for understanding the plant cell?

Recent evidence suggests that integrin is abundant in endomembranes of plant cells, and the endomembranes are clad by a sheath of cytoskeleton including F-actin. A role for endomembrane integrin and the endomembrane sheath is proposed: this system might orchestrate metabolic regulation by providing and modulating loci for channelling, and might accelerate channeling as needed by dragging the endoplasmic reticulum (ER) and organelles through the cytoplasm. To accomplish this "streaming", F-actin might lever against the rest of the endomembrane sheath and the ER might also lever against adhesion sites (i.e., plasmodesmata and plasmalemmal control centers). As an important agent in the control of cellular activities, according to this model, the endomembrane sheath would play a major part in responses to diverse signals and stresses, and under extreme stress cell survival would depend on the ability of the system to maintain enough integrity to direct critical syntheses and degradations.

NASA Discipline Plant Biology↗
NASA NTRS1993

Hypersonic aerodynamic characteristics for Langley Test Technique Demonstrator

Experimental longitudinal and lateral-directional aerodynamic characteristics were obtained for a generic transatmospheric vehicle concept referred to as the Langley Test Technique Demonstrator. The baseline configuration, without engine modules, was longitudinally and directionally unstable over the hypersonic Mach number range of the investigation and exhibited untrimmed (L/D)max levels between 2.6 and 2.8. Adding various engine modules to the baseline configuration produced mainly, degradations in lift-to-drag ratio. In general, longitudinal aerodynamic coefficients predicted with an engineering code referred to as Aerodynamic Preliminary Analysis System (APAS) were in qualitative, and often quantitative agreement with measurement.

Phillips, W. P.↗