Search NASA⌕ Search

SEARCH · Search NASA

Results for “ductile failure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Further observations of SCC in alpha-beta brass Considerations regarding the appearance of crack arrest markings during SCC

A series of constant displacement and constant extension rate stress corrosion cracking (SCC) tests was performed on an alpha-beta brass alloy in 1 N Na2SO4 solutions. The chosen mechanical and electrochemical conditions resulted in predominantly transgranular, cleavage-like failure at high (about 8 to 50 microns/s) average crack propagation rates. Crack arrest markings were observed on selected transgranular facets, which almost exclusively bordered regions of ductile overload failure. It is proposed that the observed crack velocities and the specific nature of the arrest mark appearance are most consistent with a cracking mechanism involving adsorption or some other interaction with a damaging environmental species.

Hintz, M. B.↗
DOE OSTI2024

Effect of non-uniform void distributions on the yielding of metals

High-throughput (several thousand) calculations have been carried out to investigate the yield behavior of porous materials with randomly distributed pores, porosity levels over four orders of magnitude and up to a hundred pores per simulation box. To this end, a Galerkin based fast Fourier transform (FFT) formulation was enhanced to deal with high phase contrast materials. In addition, GPU parallelization was employed in solving the governing equation for strain fluctuations using a Krylov iterative solver. Emphasis is laid on the conditions under which percolation of plastically non-deforming zones through the porous network emerge, a regime termed unhomogeneous yielding. By way of contrast, the regime where the plastic strain fluctuations (associated with the heterogeneous void-matrix aggregate) fall below the percolation threshold is defined as homogeneous yielding. Here, we find that nonuniform pore distributions only affect unhomogeneous yielding and have a universal softening effect. The extent of this distribution softening is analyzed as a function of porosity, cell size and number of realizations. Whether the uncovered universal distribution softening has direct implications on failure resistance of porous materials is discussed.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2020

Localized Strain Analysis of Ce- and Mg-Treated Cast Iron under Uniaxial Compression

Cast iron exhibits a wide range of mechanical properties, depending on its microstructural features. The microstructure of cast iron consists of several microconstituents with different elastic-plastic behavior, making the strain non-uniform across the bulk material. To understand the individual effects of these microconstituents on the overall mechanical behavior, local strain analysis using digital image correlation analysis was carried out. Samples with two different compositions (varying cerium, magnesium and silicon) were processed at different solidification velocities in a Bridgman furnace. Sections of the directionally solidified samples were loaded under uniaxial compression to measure global and local strain behavior. Despite the variability of the microstructure, the stress–strain curves obtained by digital image correlation (DIC) were found to react in a well-controlled way to changes in solidification velocity. It was observed that high-strain failure (greater than 15%) was accompanied by local straining of the softer ferritic phase, but during low-strain failure, local straining was not prominent. Higher nodularities, due to higher solidification velocities, raised the compressive strength without affecting the toughness significantly. Higher percentages of carbides led to higher compressive strengths with corresponding losses in ductility. The continuity of the matrix was also found to play an important role in the behavior during compression.

ductile failure↗
DOE OSTI2021

Bayesian calibration of a physics-based crystal plasticity and damage model

In this work, we present a model parameter calibration procedure for a physics-based crystal plasticity model. The calibration process utilizes a powerful statistics-based Bayesian calibration method. Calibration of the crystal plasticity parameters makes use of experimentally-measured data, i.e. compressive stress–strain response, from $\langle$100$\rangle$ and $\langle$123$\rangle$ single crystal copper dynamically loaded via Kolsky bar tests. The calibration of damage parameters is achieved using experimentally-measured free-surface velocity history data from plate impact test on $\langle$100$\rangle$ and $\langle$110$\rangle$ single crystal copper, which generates shock compression followed by dynamic tensile failure. A validation assessment is then carried out by comparing the calibrated model predictions and experimental measurements of the dynamic tensile damage generated in an impacted bicrystal copper plate. Lastly, a model-informed rationale for the experimentally-observed dependence of the spatial distribution of ductile damage (porosity) on crystallography is provided.

42 ENGINEERING↗
NASA NTRS1989

Characterization of failure processes in tungsten copper composites under fatigue loading conditions

A fractographic and metallographic investigation was performed on specimens of a tungsten fiber reinforced copper matrix composite (9 vol percent), which had experienced fatigue failures at elevated temperatures. Major failure modes and possible failure mechanisms, with an emphasis placed on characterizing fatigue damage accumulation, were determined. Metallography of specimens fatigued under isothermal cyclic loading suggested that fatigue damage initiates in the matrix. Cracks nucleated within the copper matrix at grain boundaries, and they propagated through cavity coalescence. The growing cracks subsequently interacted with the reinforcing tungsten fibers, producing a localized ductile fiber failure. Examinations of interrupted tests before final failure confirmed the suggested fatigue damage processes.

Kim, Yong-Suk↗
DOE OSTI2021

Irradiation hardening and ductility loss of Eurofer97 steel variants after neutron irradiation to ITER-TBM relevant conditions

Ten Eurofer97 steel variants, produced by non-standard fabrication-processing routes and modified alloying chemistries, were studied by neutron irradiations in the high flux isotope reactor. The irradiations were performed to ITER-TBM relevant conditions of ~255–350 °C, 2.94–3.24 dpa. We quantified the irradiation-induced degradation of the steels using mechanical property tests. All the steels suffered from irradiation hardening, where a significant increase in Vickers microhardness and yield stress (σ YS ) occurred, accompanied with severe loss of tensile elongation. The extent of hardening was material dependent. For T irr = 300±30 °C, most steels showed σ YS increase in the range of ~30% to as high as ~66%, except for a low temperature tempered steel with σYS increase below 15%. Despite large losses in elongation, most failures were ductile. Significant post-necking ductility was retained with reduction in area (RA) between 65–75%, but <50% for low temperature tempered steels. The ultimate tensile stress to yield stress (σ UTS /σ YS ) ratios decreased significantly after irradiation, highlighting irradiation-induced strain hardening capacity reduction. No major effect of irradiation on the plastic instability stress (σ PIS ) and true fracture stress of the steels was observed. By comparing the tensile stresses in true stress units and with literature, the results suggest that RAFM steel designing should target materials with a large separation between σ PIS and σ YS , to ensure the materials can maintain large work hardening and uniform deformation capability after irradiation. The tensile data of the steels additionally revealed a compelling evidence of an inverse trend between the change in RA and increase in σ YS of the neutron irradiated Eurofer97 type steels.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Establishing an acoustic-property relationship in laser powder bed fusion with machine learning

Quality control of Laser Powder Bed Fusion (PBF-LB) additively manufactured parts is an important hurdle inhibiting the technology’s use structural applications. Acoustic monitoring of the laser powder bed fusion process can detect defects in-situ that are known to degrade mechanical properties. However, processing-structure-property (PSP) relationships are required to extrapolate from detected defects to part performance. Here, this study explores how acoustics may be a suitable signature linking processing conditions to properties, thus effectively substituting for structure in the PSP relationship. Establishing such a relationship would enable a part’s mechanical performance to be directly predicted from its acoustic signature, reducing the need for destructive testing or microstructural analysis to ensure a part will meet performance requirements. One hundred CoCrFeMnNi high entropy alloy tensile bars were printed across 13 process conditions in a series of 6 prints. The acoustic signatures of these tensile bars were used to train machine learning models to predict each part’s mechanical properties. By using both process information and acoustic information to predict mechanical properties, yield strength was predicted 18% more accurately and ductility to failure was predicted 10% more accurately than is achieved when using duplicate parts to predict part performance. Finally, individual acoustic frequencies were investigated to determine why acoustic signatures improve mechanical property predictions and the potential physical origins of these signatures. This work demonstrates how blending acoustics, process information, and machine learning can provide in-situ diagnostics of mechanical properties and improve the reliability of the PBF-LB process.

Acoustic emission↗
DOE OSTI2021

A finite element formulation for deformation twinning induced strain localization in polycrystal magnesium alloys

Deformation twinning induces shear strain localization in hexagonal close-packed crystals and is critical for the material’s ductility and failure. Cracks often occur at twin-twin or twin-grain boundary intersections and propagate along twin bands. However, most crystal plasticity models for deformation twinning are based on a “pseudo-slip” approach and do not capture the localized deformation associated with the formation of each discrete twin band. The few exceptions are discrete twin models that involve very complex numerical algorithms and are often compromised in accuracy due to the numerical convergence. These factors make the discrete twin models hard to adopt. This paper proposes a modification to the conventional finite element weak form, to fully incorporate a twin-induced heterogeneous deformation that does not depend on the “pseudo-slip” assumption. The model starts by splitting the deformation gradient into elastic-slip-twinning components. The twin-induced deformation gradient component is computed separately by solving a microstructural evolution problem and then implemented into finite element weak form by constructing a global “twin-force” vector. The constitutive update (e.g., in the user-defined material subroutine, or UMAT, for ABAQUS) therefore avoids dealing with the twinning and recovers to the form of a regular slip-based crystal plasticity model. The results presented here indicate that the twin-induced strain localization and the associated stress-reversal phenomena near the twin band were naturally captured in the model, which was validated against an in-situ synchrotron X-ray micro-diffraction experiment.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Inference of phase field fracture models

The phase field approach to modeling fracture uses a diffuse damage field to represent cracks. This representation mollifies singularities that arise in computations with sharp interface models and some of the resultant difficulties in the mathematical and numerical treatment of fracture. Phase field fracture models have proven effective at representing crack propagation, branching, and merging. Specific formulations, beginning with brittle fracture, have also been shown to converge to classical solutions. Extensions to cover the range of material failure, including ductile and cohesive fracture, lead to an array of possible models. There exists a large body of literature focusing on this class of models and on the impact of model form on the predicted crack evolution. However, there have not been systematic studies into how optimal models may be chosen. Here, we take a first step in this direction by developing formal methods for identification of the best parsimonious model of phase field fracture given full-field data on the damage and deformation fields. We consider some of the main models that have been used for the degradation of elastic response due to damage and its propagation. Our approach builds upon Variational System Identification (VSI), a weak form variant of the Sparse Identification of Nonlinear Dynamics (SINDy). Furthermore, in this first communication we focus on synthetically generated data but we also consider central issues associated with the use of experimental full-field data, such as data sparsity and noise.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Post-irradiation examination of commercial tantalum alloys following neutron irradiation

Post irradiation examination of two commercial tantalum alloys (based on Ta-8 %W) revealed significant irradiation hardening following neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory. Tensile samples of commercial Ta alloys T-111 and ASTAR-811C were irradiated to a total neutron fluence (E > 0.1 MeV) in the range (2–4)x10 21 n/cm 2 (0.39–0.75 dpa) at an irradiation temperature near 900 °C. Tensile testing conducted at room temperature and at 800 °C revealed significant irradiation hardening under all test conditions. Samples that were tensile tested at room temperature exhibited brittle failure, whereas ductility was maintained for elevated temperature testing. The irradiation hardening and embrittlement noted for both alloys was attributed to irradiation-induced dislocation loop formation as confirmed through scanning transmission electron microscopy analysis. Corresponding energy dispersive x-ray spectroscopy revealed radiation-induced segregation of Hf in these loop populations. This Hf enrichment is shown to result in eventual co-precipitation of elongated (Hf,O)-rich precipitates along the dislocation loops. Further, these results show that irradiation hardening is enhanced via irradiation-enhanced precipitation at elevated irradiation temperatures. Consequently, the minimum recommended operating temperature window for Ta alloys should be increased to account for observed hardening/embrittlement at irradiation temperatures as high as 900 °C (1,173 K).

36 MATERIALS SCIENCE↗
NASA NTRS2003

Addendum to the User Manual for NASGRO Elastic-Plastic Fracture Mechanics Software Module

The elastic-plastic fracture mechanics modules in NASGRO have been enhanced by the addition of of the following: new J-integral solutions based on the reference stress method and finite element solutions; the extension of the critical crack and critical load modules for cracks with two degrees of freedom that tear and failure by ductile instability; the addition of a proof test analysis module that includes safe life analysis, calculates proof loads, and determines the flaw screening 1 capability for a given proof load; the addition of a tear-fatigue module for ductile materials that simultaneously tear and extend by fatigue; and a multiple cycle proof test module for estimating service reliability following a proof test.

Gregg, M. Wayne↗
NASA NTRS2012

Design and Characterization of Thin Stainless Steel Burst Disks for Increasing Two-Stage Light Gas Launcher Efficiency

Laser etched 300 series Stainless Steel Burst Disks (SSBD) ranging between 0.178 mm (0.007-in.) and 0.508mm (0.020-in.) thick were designed for use in a 17-caliber two-stage light gas launcher. First, a disk manufacturing method was selected using a combination of wire electrical discharge machining (EDM) to form the blank disks and laser etching to define the pedaling fracture pattern. Second, a replaceable insert was designed to go between the SSDB and the barrel. This insert reduced the stress concentration between the SSBD and the barrel, providing a place for the petals of the SSDB to open, and protecting the rifling on the inside of the barrel. Thereafter, a design of experiments was implemented to test and characterize the burst characteristics of SSBDs. Extensive hydrostatic burst testing of the SSBDs was performed to complete the design of experiments study with one-hundred and seven burst tests. The experiment simultaneously tested the effects of the following: two SSBD material states (full hard, annealed); five SSBD thicknesses 0.178, 0.254, 0.305, 0.381 mm (0.007, 0.010, 0.012, 0.015, 0.020-in.); two grain directions relative); number of times the laser etch pattern was repeated (varies between 5-200 times); two heat sink configurations (with and without heat sink); and, two barrel configurations (with and without insert). These tests resulted in the quantification of the relationship between SSBD thickness, laser etch parameters, and desired burst pressure. Of the factors investigated only thickness and number of laser etches were needed to develop a mathematical relationship predicting hydrostatic burst pressure of disks using the same barrel configuration. The fracture surfaces of two representative SSBD bursts were then investigated with a scanning electron microscope, one burst hydrostatically in a fixture and another dynamically in the launcher. The fracture analysis verified that both burst conditions resulted in a ductile overload failure indicated by transgranular microvoid coalescence, non-fragmenting rupture and mixed tensile and shear failure modes, regardless of the material states tested. More testing is underway to determine the relationship between SSBD burst pressure and projectile velocity.

Tylka, Jonathan M.↗
DOE OSTI2024

Tailoring Carbide Dispersed Steels: A Path to Increased Strength and Hydrogen Tolerance

The use of transition metal carbides is reported for use as a hydrogen trapping mechanism for ferritic and austenitic steel materials. The program combined computational modeling and simulations to guide experiments towards candidate metal carbide traps, both for interfacial and interior trapping. It was found that interfacial trapping is less effective than interior trapping, with the group IVB transition metal carbides being the most effect internal traps with a loss of carbon. The sub-stoichiometric rocksalt structure accommodate the hydrogen atoms in its octahedral interstices. Using percolation theory, carbon loss of approximately 25% or more was sufficient to ensure an interconnected network of vacancies for such trapping from the surface to the internal sites within the carbide. Using this as a guide, the program developed a means to provide a uniform dispersion of ZrC nanoparticles with either Fe or 304L micron-scale powders which was then consolidated by direct current sintering. Electrolytic hydrogen diffusivity studies confirmed the reduction of hydrogen diffusion in the matrix with increasing ZrC content, which was a linear response over the sample range studied (0.01 to 1.0 wt.%). The consolidated material was micro-tensile tested in either a non-hydrogen or hydrogen charge condition and compared to a control with no carbides. Additions up to 0.05 wt.% ZrC increased the yield strength with no loss in ductility in either the non-hydrogen or hydrogen tested condition. ZrC concentrations above this amount further increased the yield strength at the expense of ductility. While these samples had a lower absolute ductility value prior to failure, the relative change in ductility between the non-hydrogen and hydrogen charge states was less for the carbides than that of the control. Metal-rich ZrC nanoparticles were fabricated through a conformal coating process yielding ZrC0.66 particles that were then incorporated into a metal matrix. Notch fatigue testing in a hydrogen environment was conducted where the number of cycles to failure was found to be less in the control than that of the carbide addition. However, the spread in experimental data and the number of samples tested limits a conclusive outcome based on defects noticed in the gauge section of all the powder processed samples. The collective outcomes of this report provide further insight into the mechanisms by which carbides act as hydrogen traps; a means to process such carbides through powder metallurgy; and their associated mechanical performance in either a non-hydrogen or hydrogen-charged condition.

08 HYDROGEN↗
DOE OSTI2022

304L Can Crush Validation Studies

Accurate prediction of ductile behavior of structural alloys up to and including failure is essential in component or system failure assessment, which is necessary for nuclear weapons alteration and life extensions programs of Sandia National Laboratories. Modeling such behavior requires computational capabilities to robustly capture strong nonlinearities (geometric and material), rate- dependent and temperature-dependent properties, and ductile failure mechanisms. This study's objective is to validate numerical simulations of a high-deformation crush of a stainless steel can. The process consists of identifying a suitable can geometry and loading conditions, conducting the laboratory testing, developing a high-quality Sierra/SM simulation, and then drawing comparisons between model and measurement to assess the fitness of the simulation in regards to material model (plasticity), finite element model construction, and failure model. Following previous material model calibration, a J 2 plasticity model with a microstructural BCJ failure model is employed to model the test specimen made of 304L stainless steel. Simulated results are verified and validated through mesh and mass-scaling convergence studies, parameter sensitivity studies, and a comparison to experimental data. The converged mesh and degree of mass-scaling are the mesh discretization with 140,372 elements, and a mass scaling with a target time increment of 1.0e-6 seconds and time step scale factor of 0.5, respectively. Results from the coupled thermal-mechanical explicit dynamic analysis are comparable to the experimental data. Simulated global force vs displacement (F/D) response predicts key points such as yield, ultimate, and kinks of the experimental F/D response. Furthermore, the final deformed shape of the can and field data predicted from the analysis are similar to that of the deformed can, as measured by 3D optical CMM scans and DIC data from the experiment.

36 MATERIALS SCIENCE↗
NASA NTRS2003

Flaw Tolerance In Lap Shear Brazed Joints

This paper presents results of the second part of an on-going effort to gain better understanding of defect tolerance in braze joints. In the first part of this three-part series, we mechanically tested and modeled the strength of the lap joints as a function of the overlap distance. A failure criterion was established based on the zone damage theory, which predicts the dependence of the lap joint shear strength on the overlap distance, based on the critical size of a finite damage zone or an overloaded region in the joint. In this second part of the study, we experimentally verified the applicability of the damage zone criterion on prediction of the shear strength of the lap joint and introduced controlled flaws into the lap joints. The purpose of the study was to evaluate the lap joint strength as a function of flaw size and its location through mechanical testing and nonlinear finite element analysis (FEA) employing damage zone criterion for definition of failure. The results obtained from the second part of the investigation confirmed that the failure of the ductile lap shear brazed joints occurs when the damage zone reaches approximately 10% of the overlap width. The same failure criterion was applicable to the lap joints containing flaws.

Wang, Len↗
NASA NTRS1990

Tidal disruption of solid bodies

The problem of stress, strain, and breakup in solid satellites and stray bodies subject to tidal perturbations is presently addressed in view of three novel considerations. After presenting a new analytic solution for the stress tensor in a homogeneous and compressible elastic sphere, where the inclusion of compressibility alters stresses by several percent, realistic failure criteria are noted to demonstrate the general failure of such ductile bodies as iron meteoroids by plastic shear, while brittle ice bodies fail by either tensile or shear fracture. A reexamination of crack propagation after initial failure allows the diverse breakup criteria to be reconciled.

Dobrovolskis, Anthony R.↗
DOE OSTI2026

Effect of deposition rate on microstructure and mechanical properties of 17-4 PH stainless steel fabricated by laser engineered net shaping

Laser engineered net shaping (LENS) is an additive manufacturing technique for fabricating and repairing metallic components. However, the relationships between its process parameters and the resulting mechanical properties of alloys such as 17-4 precipitation-hardening (PH) stainless steel require further investigation to enable reliable application. This study examines the specific effect of LENS deposition rate on the microstructure and mechanical properties of 17-4 PH stainless steel. Specimens were fabricated at two different deposition rates (8.47 and 9.31 mm s−1), subjected to subsequent solution and H900 aging treatment, and then evaluated via tensile testing, hardness measurements, and microscopy. A higher deposition rate results in a finer grain structure but increased porosity, leading to greater ultimate tensile strength (∼1294 MPa) yet lower ductility (strain at failure ∼5.8%) compared to the slower deposition rate (∼1266 MPa, ∼9.0% strain). Hardness follows the same trend as tensile strength. Tensile fracture surfaces for both conditions exhibited a mixed mode of ductile dimples and brittle quasi-cleavage regions, with chromium/silicon oxide particles identified within dimples. Complementary finite element modeling indicates that small void fractions primarily reduce ductility by enhancing localized plasticity, with only a marginal decrease in tensile strength. These integrated experimental and numerical results elucidate the mechanical properties linked to deposition rate, providing insight into tailoring LENS processes to achieve desired properties of 17-4 PH stainless steel.

17-4 PH stainlesssteel↗