Search NASA⌕ Search

SEARCH · Search NASA

Results for “dwellings”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Evaluation of the cyclic behavior of aircraft turbine disk alloys, part 2

Several nickel-base aircraft turbine disk superalloys were evaluated at 650 C for resistance to fatigue crack initiation and propagation under cyclic and cyclic/dwell conditions. Controlled strain low cycle fatigue (LCF) and controlled load crack propagation tests were performed and results utilized to provide a direct comparison among the alloys. Tests were performed on selected alloys to evaluate the effects of hold times, mean stresses, stress-dwell cycle types, inert environment, and contractor test methods. At the lower total strain ranges of interest, the alloys exhibited generally increasing initiation life with increasing tensile strength for both cyclic (0.33 Hz) and cyclic/dwell (900-sec hold per cycle) conditions. Rank order of the alloys by LCF initiation life changed substantially at higher strain ranges, approaching the rank order expected from monotonic tensile ductilities. The effect of the 900 sec (15 min) hold time fatigue life varied significantly from alloy to alloy. Generally, the higher-strength, finer-grained alloys exhibited more significant reductions in fatigue life due to the dwell. The effects of mean strain were found to be negligible and the effects of mean stress were pronounced. At high strain ranges the mean stress was near zero and did not contribute to reduction in life. At low strain ranges, however, mean stresses were large and significant reductions in LCF lives occurred.

Cowles, B. A.↗
NASA NTRS1981

Effects of curved approach paths and advanced displays on pilot scan patterns

The effect on pilot scan behavior of both advanced cockpit and advanced manuevers was assessed. A series of straight-in and curved landing approaches were performed in the Terminal Configured Vehicle (TCV) simulator. Two comparisons of pilot scan behavior were made: (1) pilot scan behavior for straight-in approaches compared with scan behavior previously obtained in a conventionally equipped simulator, and (2) pilot scan behavior for straight-in approaches compared with scan behavior for curved approaches. The results indicate very similar scanning patterns during the straight-in approaches in the conventional and advanced cockpits. However, for the curved approaches pilot attention shifted to the electronic horizontal situation display (moving map), and a new eye scan path appeared between the map and the airspeed indicator. The very high dwell percentage and dwell times on the electronic displays in the TCV simulator during the final portions of the approaches suggest that the electronic attitude direction indicator was well designed for these landing approaches.

Harris, R. L., Sr.↗
NASA NTRS1980

Cyclic behavior of turbine disk alloys at 650 C

Five gas turbine disk alloys representing a range of strengths and processing methods were tested for resistance to both cyclic crack initiation and propagation at 650 C using a 0.33 Hz fatigue cycle and a cycle incorporating a 900 s tensile dwell. At the low strain ranges pertinent to disks, resistance to crack initiation increased with increasing tensile yield strength among the alloys, though the advantage was somewhat smaller for the creep fatigue cycle. Cyclic crack growth resistance, however, decreased with increasing strength and very markedly so for the dwell cycle.

Cowles, B. A.↗
NASA NTRS1981

Experience on the use of MOSTAB-HFW computer code for horizontal-axis wind turbines

Three topics are covered dealing with the frequencies of a rotating beam, the use of the fundamental mode of a uniform cantilever beam, and the analysis of resonance dwell. Immensely high peak loads were generated by the code for resonance dwell indicating further need for including structural damping and for transient analysis capability. The effect of structural damping, newly incorporated in the code, is described.

Yu, Y. Y.↗
NASA NTRS1982

Performance analysis for the expanding search PN acquisition algorithm

An approach is described for approximating the cumulative probability distribution of the acquisition time of the serial pseudonoise (PN) search algorithm. The results are applicable to both variable and fixed dwell time systems. The theory is developed for the case where some a priori information is available on the PN code epoch (reacquisition problem or acquisition of very long codes). Also considered is the special case of a search over the whole code. The accuracy of the approximation is demonstrated by comparisons with published exact results for the fixed dwell time algorithm.

Braun, W. R.↗
NASA NTRS1983

VAS operational procedures and results at the Kansas City Satellite Field Services Station

An operational assessment of VAS data by using a Man-computer Interactive Data Access System (McIDAS) terminal linked by a 9600 band telephone line is discussed. Seven hours of VAS data were processed and edited daily. Data was scheduled 16 hours a day, 7 days a week; however, during this time period there were very few days with 16 hours of data to evalute. The McIDAS terminal, which has 10 display frames and 5 graphics, provide access to the sounding data processed. These data are processed using two procedures. The dwell sounding data are generated by using all 12 spectral channels with a spin budget of 39. To provide coverage for most of the United States, soundings are made starting at 18 minutes after the hour from approximately 49 deg N to 36 deg N and at 48 minutes after the hour from 36 deg N to 26 deg N. The dwell imaging mode uses 11 channels but the spin budge is 17. With the reduced spin budget, retrievals can be made at 18 or 48 minutes after the hour for approximately 44 deg N to 27 deg N. With these constraints a schedule, of data sets was proposed to use the schedule and how the data set could be used are shown.

Heckman, B.↗
NASA NTRS1983

Low strain, long life creep fatigue of AF2-1DA and INCO 718

Two aircraft turbine disk alloys, GATORIZED AF2-DA and INCO 718 were evaluated for their low strain long life creep-fatigue behavior. Static (tensile and creep rupture) and cyclic properties of both alloys were characterized. The cntrolled strain LCF tests were conducted at 760 C (1400 F) and 649 C (1200 F) for AF2-1DA and INCO 718, respectively. Hold times were varied for tensile, compressive and tensile/compressive strain dwell (relaxation) tests. Stress (creep) hold behavior of AF2-1DA was also evaluated. Generally, INCO 718 exhibited more pronounced reduction in cyclic life due to hold than AF2-1DA. The percent reduction in life for both alloys for strain dwell tests was greater at low strain ranges (longer life regime). Changing hold time from 0 to 0.5, 2.0 and 15.0 min. resulted in corresponding reductions in life. The continuous cycle and cyclic/dwell initiation failure mechanism was predominantly transgranular for AF2-1DA and intergranular for INCO 718.

Thakker, A. B.↗
NASA NTRS1984

Flight versus simulator scan behavior

It is pointed out that most of the modern flight simulators used for pilot training have included expensive motion bases, while the quantitative justification for motion is lacking. The present investigation is concerned with the effects of flight versus simulator conditions on scan behavior as a function of control mode and the presence or absence of traffic on the map display. Matching tests conducted in flight and in a fixed-base simulator permitted an evaluation of the differences in scanning behavior in the real world (flight) and in the 'less real' world (simulator). Scanning behavior in flight was found to be significantly different from the simulator. In flight, the dwell percentage increased on the Electronic Attitude Direction Indicator (EADI), and decreased on the Electronic Horizontal Situation Indicator (EHSI). The average dwell time on all instruments decreased in flight.

Spady, A. A., Jr.↗
NASA NTRS1985

Time composite sounding

In the time composite sounding mode, the Vertical Atmospheric Sounder (VAS) data is collected in a series of images of one spin each rather than in the dwell sound mode where single lines are repeatedly scanned. A drawback of the time composite method is temporal smearing of the data, but to compensate this there is also the chance that shifting cloud patterns will permit better spatial coverage. Time composite sounding was performed for a single case study, June 14, 1984. Four, ten minute single spin swaths were processed. The principal conclusion was that the time composite results were at least equivalent to the conventional dwell sounding results, despite the fact that compositing was done in a less than optimum way because of software limitations.

Hayden, C.↗
NASA NTRS1988

Rapid code acquisition algorithms employing PN matched filters

The performance of four algorithms using pseudonoise matched filters (PNMFs), for direct-sequence spread-spectrum systems, is analyzed. They are: parallel search with fix dwell detector (PL-FDD), parallel search with sequential detector (PL-SD), parallel-serial search with fix dwell detector (PS-FDD), and parallel-serial search with sequential detector (PS-SD). The operation characteristic for each detector and the mean acquisition time for each algorithm are derived. All the algorithms are studied in conjunction with the noncoherent integration technique, which enables the system to operate in the presence of data modulation. Several previous proposals using PNMF are seen as special cases of the present algorithms.

Su, Yu T.↗
NASA NTRS1991

Closed-Loop Chopping-Mirror Controller

Motion of chopping mirror controlled very precisely by feedback circuit originally developed for mirrors in orbiting infrared telescopes. Mirror position and velocity electronically sensed and commanded. New controller enables selection of different chopping frequencies, angular amplitudes, dwell times, and dwell positions. Also reduces noise and vibration by eliminating mechanical stops and reduces energy consumption in actuator.

Lorell, Kenneth R.↗
NASA NTRS1990

Geoscience Laser Ranging System - Estimated accuracy of geodetic parameters and their dependence on system characteristics

Covariance analysis of the performance of the Geoscience Laser Ranging System (GLRS) indicates that three-dimensional relative positions can be recovered to an accuracy of several millimeters over spatial scales from a few kilometers to several hundred kilometers and over temporal scales as short as several days. The key factors influencing the accuracy are range noise, number of targets and their locations, system pointing capability, dwell time on the targets, orbital geometry, and gravity field uncertainties. Based on the present trade-off studies, GLRS is designed to provide range measurements with 10 mm or better accuracy, fire at a rate of 40 pulses-per-second, point over a cone extending to 50 deg from nadir, and operate with a dwell time on individual targets of 2 s or less. Given a strain rate of 10 to the -14th/s, estimated GLRS accuracy parameters suggest that the deformation can be detected in less than a month if it extends over 100 km and in less than 6 months if it extends over 10 km.

Cohen, Steven C.↗
NASA NTRS1993

Techniques used for the analysis of oculometer eye-scanning data obtained from an air traffic control display

The methodology and techniques used to collect and analyze look-point position data from a real-time ATC display-format comparison experiment are documented. That study compared the delivery precision and controller workload of three final approach spacing aid display formats. Using an oculometer, controller lookpoint position data were collected, associated with gaze objects (e.g., moving aircraft) on the ATC display, and analyzed to determine eye-scan behavior. The equipment involved and algorithms for saving, synchronizing with the ATC simulation output, and filtering the data are described. Target (gaze object) and cross-check scanning identification algorithms are also presented. Data tables are provided of total dwell times, average dwell times, and cross-check scans. Flow charts, block diagrams, file record descriptors, and source code are included. The techniques and data presented are intended to benefit researchers in other studies that incorporate non-stationary gaze objects and oculometer equipment.

Crawford, Daniel J.↗
NASA NTRS1994

Doppler radar detection of vortex hazard indicators

Wake vortex experiments were conducted at White Sands Missile Range, NM using the AN/MPS-39 Multiple Object Tracking Radar (MOTR). The purpose of these experiments was twofold. The first objective was to verify that radar returns from wake vortex are observed for some time after the passage of an aircraft. The second objective was to verify that other vortex hazard indicators such as ambient wind speed and direction could also be detected. The present study addresses the Doppler characteristics of wake vortex and clear air returns based upon measurements employing MOTR, a very sensitive C-Band phased array radar. In this regard, the experiment was conducted so that the spectral characteristics could be determined on a dwell to-dwell basis. Results are presented from measurements of the backscattered power (equivalent structure constant), radial velocity and spectral width when the aircraft flies transverse and axial to the radar beam. The statistics of the backscattered power and spectral width for each case are given. In addition, the scan strategy, experimental test procedure and radar parameters are presented.

Nespor, Jerald D.↗
NASA NTRS1995

Description and Simulation of a Fast Packet Switch Architecture for Communication Satellites

The NASA Lewis Research Center has been developing the architecture for a multichannel communications signal processing satellite (MCSPS) as part of a flexible, low-cost meshed-VSAT (very small aperture terminal) network. The MCSPS architecture is based on a multifrequency, time-division-multiple-access (MF-TDMA) uplink and a time-division multiplex (TDM) downlink. There are eight uplink MF-TDMA beams, and eight downlink TDM beams, with eight downlink dwells per beam. The information-switching processor, which decodes, stores, and transmits each packet of user data to the appropriate downlink dwell onboard the satellite, has been fully described by using VHSIC (Very High Speed Integrated-Circuit) Hardware Description Language (VHDL). This VHDL code, which was developed in-house to simulate the information switching processor, showed that the architecture is both feasible and viable. This paper describes a shared-memory-per-beam architecture, its VHDL implementation, and the simulation efforts.

Quintana, Jorge A.↗
NASA NTRS1998

Liquid Motion in a Rotating Tank Experiment (LME)

The Liquid Motion Experiment (LME), which flew on STS 84 in May 1997, was an investigation of liquid motions in spinning, nutating tanks. LME was designed to quantify the effects of such liquid motions on the stability of spinning spacecraft, which are known to be adversely affected by the energy dissipated by the liquid motions. The LME hardware was essentially a spin table which could be forced to nutate at specified frequencies at a constant cone angle, independently of the spin rate. Cylindrical and spherical test tanks, partially filled with liquids of different viscosities, were located at the periphery of the spin table to simulate a spacecraft with off-axis propellant tanks; one set of tanks contained generic propellant management devices (PMDs). The primary quantitative data from the flight tests were the liquid-induced torques exerted on the tanks about radial and tangential axes through the center of the tank. Visual recordings of the liquid oscillations also provided qualitative information. The flight program incorporated two types of tests: sine sweep tests, in which the spin rate was held constant and the nutation frequency varied over a wide range; and sine dwell test, in which both the spin rate and the nutation frequency were held constant. The sine sweep tests were meant to investigate all the prominent liquid resonant oscillations and the damping of the resonances, and the sine dwell tests were meant to quantify the viscous energy dissipation rate of the liquid oscillations for steady state conditions. The LME flight data were compared to analytical results obtained from two companion IR&D programs at Southwest Research Institute. The comparisons indicated that the models predicted the observed liquid resonances, damping, and energy dissipation rates for many test conditions but not for all. It was concluded that improved models and CFD simulations are needed to resolve the differences. This work is ongoing under a current IR&D program.

Deffenbaugh, D. M.↗
NASA NTRS2000

The Effect of Boron on the Low Cycle Fatigue Behavior of Disk Alloy KM4

The durability of powder metallurgy nickel base superalloys employed as compressor and turbine disks is often limited by low cycle fatigue (LCF) crack initiation and crack growth from highly stressed surface locations (corners, holes, etc.). Crack growth induced by dwells at high stresses during aerospace engine operation can be particularly severe. Supersolvus solution heat treatments can be used to produce coarse grain sizes approaching ASTM 6 for improved resistance to dwell fatigue crack growth. However, the coarse grain sizes reduce yield strength, which can lower LCF initiation life. These high temperature heat treatments also can encourage pores to form. In the advanced General Electric disk superalloy KM4, such pores can initiate fatigue cracks that limit LCF initiation life. Hot isostatic pressing (HIP) during the supersolvus solution heat treatment has been shown to improve LCF initiation life in KM4, as the HIP pressure minimizes formation of the pores. Reduction of boron levels in KM4 has also been shown to increase LCF initiation life after a conventional supersolvus heat treatment, again possibly due to effects on the formation tendencies of these pores. However, the effects of reduced boron levels on microstructure, pore characteristics, and LCF failure modes in KM4 still need to be fully quantified. The objective of this study was to determine the effect of boron level on the microstructure, porosity, LCF behavior, and failure modes of supersolvus heat treated KM4.

Gabb, Timothy↗
NASA NTRS2004

Microstructural Evaluation of KM4 and SR3 Samples Subjected to Various Heat Treatments

The gamma-gamma microstructures of two advanced powder metallurgy disk alloys, KM4 and SR3, were quantified after a series of heat treatments using transmission electron microscopy and image analysis. Relationships between the heat treatments and the resulting gamma distributions were evaluated. Statistical correlations between the gamma distributions and the reported tensile strengths, creep resistances, and dwell crack growth resistances were separately assessed for each alloy. To avoid the effects of grain size related mechanisms, the grain size of the samples used in the correlations for each alloy were limited to narrow ranges of about 1.5 in ASTM grain size number. In both alloys, yield and tensile strength increased with increasing fraction of medium sized gamma. The strength increased as the size of the medium gamma decreased and the size of the fine gamma increased. Time to 0.2 percent creep in SR3 increased with increasing medium gamma volume fraction, and decreasing fine gamma sizes. However, 0.2 percent creep time was not clearly correlated with the gamma microstructures of KM4 specimens, apparently due to effects of stabilization heat treatments which greatly suppress creep resistance. Dwell fatigue crack growth rate decreased with increasing medium gamma volume fraction, indicating more medium gamma is beneficial. The crack growth rate also decreased with decreasing gamma size, indicating finer gamma is better.

Ellis, David↗