Search NASA⌕ Search

SEARCH · Search NASA

Results for “edge modes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Graph-based real-time fault diagnostics

A real-time fault detection and diagnosis capability is absolutely crucial in the design of large-scale space systems. Some of the existing AI-based fault diagnostic techniques like expert systems and qualitative modelling are frequently ill-suited for this purpose. Expert systems are often inadequately structured, difficult to validate and suffer from knowledge acquisition bottlenecks. Qualitative modelling techniques sometimes generate a large number of failure source alternatives, thus hampering speedy diagnosis. In this paper we present a graph-based technique which is well suited for real-time fault diagnosis, structured knowledge representation and acquisition and testing and validation. A Hierarchical Fault Model of the system to be diagnosed is developed. At each level of hierarchy, there exist fault propagation digraphs denoting causal relations between failure modes of subsystems. The edges of such a digraph are weighted with fault propagation time intervals. Efficient and restartable graph algorithms are used for on-line speedy identification of failure source components.

Padalkar, S.↗
NASA NTRS2004

Numerical and Experimental Dynamic Characteristics of Thin-Film Membranes

Presented is a total-Lagrangian displacement-based non-linear finite-element model of thin-film membranes for static and dynamic large-displacement analyses. The membrane theory fully accounts for geometric non-linearities. Fully non-linear static analysis followed by linear modal analysis is performed for an inflated circular cylindrical Kapton membrane tube under different pressures, and for a rectangular membrane under different tension loads at four comers. Finite element results show that shell modes dominate the dynamics of the inflated tube when the inflation pressure is low, and that vibration modes localized along four edges dominate the dynamics of the rectangular membrane. Numerical dynamic characteristics of the two membrane structures were experimentally verified using a Polytec PI PSV-200 scanning laser vibrometer and an EAGLE-500 8-camera motion analysis system.

Young, Leyland G.↗
NASA NTRS2014

Development and Characterization of Embedded Sensory Particles Using Multi-Scale 3D Digital Image Correlation

A method for detecting fatigue cracks has been explored at NASA Langley Research Center. Microscopic NiTi shape memory alloy (sensory) particles were embedded in a 7050 aluminum alloy matrix to detect the presence of fatigue cracks. Cracks exhibit an elevated stress field near their tip inducing a martensitic phase transformation in nearby sensory particles. Detectable levels of acoustic energy are emitted upon particle phase transformation such that the existence and location of fatigue cracks can be detected. To test this concept, a fatigue crack was grown in a mode-I single-edge notch fatigue crack growth specimen containing sensory particles. As the crack approached the sensory particles, measurements of particle strain, matrix-particle debonding, and phase transformation behavior of the sensory particles were performed. Full-field deformation measurements were performed using a novel multi-scale optical 3D digital image correlation (DIC) system. This information will be used in a finite element-based study to determine optimal sensory material behavior and density.

Cornell, Stephen R.↗
NASA NTRSDate not supplied

Modeling Boundary-Layer Transition in Subsonic Flow over a Swept Wing

Predicting the onset of boundary-layer transition is often more accurate using physics-based models that directly compute disturbance growth rather than phenomenological models often implemented into industrial CFD codes. The aim of this ongoing study is to calibrate linear, physics-based computations of transition in subsonic flows over swept wings against a large set of experimental data. Advancing the calibration of linear models of transition contributes to the CFD-Vision-2030 goal of automated boundary-layer transition prediction. This progress report uses the dual N-factor method to model transition over the swept NACA 64-2-015A wing. The flow conditions match selected test conditions from an extensive experimental dataset acquired from the NASA Ames 12-ft Pressure Tunnel. The OVERFLOW 2.4b flow solver is used to obtain laminar basic states based on an infinite-span assumption. Stability analyses are performed on 365 distinct configurations with linear stability theory (LST) and parabolized stability equations (PSE) from the Langley Stability and Transition Analysis Codes (LASTRAC), modeling the growth of Tollmien-Schlichting (TS) and stationary crossflow (SCF) disturbances. From a total of 67 data points for unswept, i.e., TS-dominant configurations, the critical N-factor based on PSE is found to be N_TS = 9. The SCF critical N-factor is found to be near 8 for the highly swept, SCF-dominant configurations. Dual N-factor curves for both LST and PSE computations demonstrate a high level of interaction between TS and SCF. It may be worthwhile to investigate an alternate metric to visualize maximal SCF amplification upstream of the transition location to account for the growth of SCF modes near the leading edge, which is not considered in the conventional applications of the dual N-factor criterion.

boundary-layer transition↗
NASA NTRSDate not supplied

Modeling Boundary-Layer Transition in Subsonic Flow over a Swept Wing

Predicting the onset of boundary-layer transition is often more accurate using physics-based models that directly compute disturbance growth rather than phenomenological models often implemented into industrial CFD codes. The aim of this ongoing study is to calibrate linear, physics-based computations of transition in subsonic flows over swept wings against a large set of experimental data. Advancing the calibration of linear models of transition contributes to the CFD-Vision-2030 goal of automated boundary-layer transition prediction. This progress report uses the dual N-factor method to model transition over the swept NACA 64-2-015A wing. The flow conditions match selected test conditions from an extensive experimental dataset acquired from the NASA Ames 12-ft Pressure Tunnel. The OVERFLOW 2.4b flow solver is used to obtain laminar basic states based on an infinite-span assumption. Stability analyses are performed on 365 distinct configurations with linear stability theory (LST) and parabolized stability equations (PSE) from the Langley Stability and Transition Analysis Codes (LASTRAC), modeling the growth of Tollmien-Schlichting (TS) and stationary crossflow (SCF) disturbances. From a total of 67 data points for unswept, i.e., TS-dominant configurations, the critical N-factor based on PSE is found to be N_TS = 9. The SCF critical N-factor is found to be near 8 for the highly swept, SCF-dominant configurations. Dual N-factor curves for both LST and PSE computations demonstrate a high level of interaction between TS and SCF. It may be worthwhile to investigate an alternate metric to visualize maximal SCF amplification upstream of the transition location to account for the growth of SCF modes near the leading edge, which is not considered in the conventional applications of the dual N-factor criterion.

computational modeling↗
NASA NTRS1981

On eigensolutions for discontinuous liners in a duct containing uniform mean flow

Sound attenuation in a rectangular acoustically lined duct containing uniform mean flow is analytically investigated using the generalized Wiener-Hopf technique. Uniqueness of the solution is enforced for lined sections of the finite axial extent by imposing edge conditions at the liner interface. Possible edge conditions are considered, including the Kutta condition, and the causal solution corresponding to edge conditions is considered the best choice. Solution methods such as the mode matching and singularity methods imply differing edge conditions, and results show that power attenuation is insensitive to the imposed edge conditions, although significant differences are observed for the reflection coefficient. The amplitude of the exponentially increasing instability mode in the lined section must be set to zero as a first approximation to the nonlinear situation, and results indicate that measurements of the reflection factor can be used to make a more definite decision about physically appropriate edge conditions.

Koch, W.↗
NASA NTRS1992

Slow mode transition in the frontside magnetosheath

Three magnetosheath passes with density enhancements in front of the magnetopause are studied with data from ISEE 1, 2, and 3. The density structure appears to be locally generated and slow mode in nature. In one pass when ISEE 1 and 2 were well separated, the motion of the density structure can be determined. The density structure appears to stand in the magnetosheath flow. Thus, it propagates upstream in the rest frame of the flow. The flow in and near the density structure appears to be closer to isothermal than adiabatic. The flow velocity decreases from super-slow to being close to the intermediate and slow mode velocities at the outer edge of the density structure. This study provides additional evidence that the density structure in front of the magnetopause is a slow mode transition in which the flow velocity decreases to the MHD slow mode velocity. The slow mode transition may consist of two wave fronts and a region with strong slow mode waves. This slow mode transition may play an important role in establishing the flow and field pattern near the magnetopause.

Song, P.↗
NASA NTRS2000

Flame Spread Along Free Edges of Thermally Thin Samples in Microgravity

The effects of imposed flow velocity on flame spread along open edges of a thermally thin cellulosic sample in microgravity are studied experimentally and theoretically. In this study, the sample is ignited locally at the middle of the 4 cm wide sample and subsequent flame spread reaches both open edges of the sample. The following flame behaviors are observed in the experiments and predicted by the numerical calculation; in order of increased imposed flow velocity: (1) ignition but subsequent flame spread is not attained, (2) flame spreads upstream (opposed mode) without any downstream flame, and (3) the upstream flame and two separate downstream flames traveling along the two open edges (concurrent mode). Generally, the upstream and downstream edge flame spread rates are faster than the central flame spread rate for an imposed flow velocity of up to 5 cm/s. This is due to greater oxygen supply from the outer free stream to the edge flames than the central flames, For the upstream edge flame, the greater oxygen supply results in a flame spread rate that is nearly independent of, or decreases gradually, with the imposed flow velocity. The spread rate of the downstream edge, however, increases significantly with the imposed flow velocity.

Mell, W. E.↗
NASA NTRS1999

Reflections of AE Waves in Finite Plates: Finite Element Modeling and Experimental Measurements

The capability of a three-dimensional dynamic finite element method for predicting far-field acoustic emission signals in thin plates of finite lateral extent, including their reflections from the plate edges, was investigated. A lead break (Hsu-Neilsen) source to simulate AE was modeled and used in the experimental measurements. For the thin plate studied, the signals were primarily composed of the lowest order symmetric (S0) and antisymmetric (A0) Lamb modes. Experimental waveforms were detected with an absolutely calibrated, wideband, conical element transducer. The conditions of lead fractures both on the surface of the plate as well as on the edge of the plate were investigated. Surface lead breaks preferentially generate the A0 mode while edge lead breaks generate the S0 mode. Reflections of developed plate waves from both normal and oblique incidence angles were evaluated. Particularly interesting for the case of the lead break on the plate edge were S0 waves produced by the interaction of a Rayleigh wave with the plate corner and by a bulk shear wave mode converting at the side edge. The Rayleigh wave, in this case, propagated along the specimen edge. For all cases considered, the experimental measurements were in good agreement with the predictions of the finite element model.

Prosser, W. H.↗
NASA NTRS2000

Flame Spread Along Free Edges of Thermally Thin Samples in Microgravity

The effects of imposed flow velocity on flame spread along open edges of a thermally thin cellulosic sample in microgravity were studied experimentally and theoretically. In this study, the sample was ignited locally at the middle of the 4 cm wide sample, and subsequent flame spread reached both open edges of the sample along the direction of the flow. The following flame behaviors were observed in the experiments and predicted by the numerical calculation, in order of increased imposed flow velocity: (1) ignition but subsequent flame spread was not attained, (2) flame spread upstream (opposed mode) without any downstream flame, and (3) the upstream flame and two separate downstream flames traveled along the two open edges (concurrent mode). Generally, the upstream and downstream edge flame spread rates were faster than the central flame spread rate for an imposed flow velocity of up to 5 cm/s. This was due to greater oxygen supply from the outer free stream to the edge flames and more efficient heat transfer from the edge flames to the sample surface than the central flames. For the upstream edge flame, flame spread rate was nearly independent of, or decreased gradually with, the imposed flow velocity. The spread rate of the downstream edge, however, increased significantly with the imposed flow velocity.

MICROGRAVITY↗
NASA NTRS1983

Noise generation by a finite span swept airfoil

An analysis is developed for the noise generated by a convected gust interacting with a single swept airfoil. The airfoil spans a channel with infinite parallel walls which contains a uniform subsonic mean flow. High frequency gusts, for which the noise generation is concentrated at the airfoil leading edge, are considered. The solution utilizes the Wiener-Hopf technique applied to the equations in nonorthogonal coordinates. Closed form expressions for the farfield acoustic pressure are obtained. The convected gust is assumed to be a plane wave, i.e., the lowest order spanwise mode. Because of the swept leading edge, this convected gust generates acoustic modes of all orders. At high frequencies and low Mach numbers, moderate sweep angles produce substantial noise reductions. The residual acoustic energy is carried mainly by the higher modes. The airfoil sweep also modulates the basic high frequency farfield directivity, producing lobed patterns. The angular modulation of the directivity patterns is most pronounced for the lower order modes.

Kerschen, E. J.↗
NASA NTRSDate not supplied

Simulating Meteor Ablation at the Hypersonic Materials Environmental Test System

The ablation mechanisms of stony meteorite material and a terrestrial analog were investigated at the Hypersonic Materials Environmental Test System (HyMETS) facility at NASA’s Langley Research Center. The primary analyte (Tamdakht-H5) and arc-jet test conditions were chosen to simulate the entry of an ordinary chondrite through the Earth’s mesosphere. Basalt was selected to compare the meteorite response against material with enhanced polymerization and an elevated concentration of volatile species. The initial ablation process for each material commences with the vaporization of volatile species and germination of a viscous melt layer on the stagnation surface. However, each material exhibited distinct mass loss mechanisms, with basalt recessing at twice the rate of Tamdakht. Inspection of high-speed video and chemical analysis of the post-test melt layer suggests the dominant mode of mass loss of Tamdakht is expressed through the vaporization of volatile compounds. Vaporization rates of Tamdakht are 18x higher than basalt under the most severe test conditions which provides enhanced thermal shielding. Furthermore, Tamdakht produces a relatively stable melt flow, as evidenced by perpetual growth at the sidewall and the exiguous detachment of molten material into the flow. The ablation mechanism of basalt is markedly different from Tamdakht and is governed by volatile species in the virgin material. The dominant mode of mass loss for basalt is attributed to the detachment of large sections of the stagnation surface near the edge radius. An additional but subordinate mode of mass loss is assigned to the removal of melt flow as it passes over the edge radius, where shear forces overcome the rheological properties of the molten matter. Finally, mechanistic details will be discussed in terms of designing future test campaigns, developing meteorite-based materials response models, and impacting the broader scope of the Asteroid Threat Assessment Project (ATAP).

Meteor Ablation↗
NASA NTRS1995

Simplified data reduction methods for the ECT test for mode 3 interlaminar fracture toughness

Simplified expressions for the parameter controlling the load point compliance and strain energy release rate were obtained for the Edge Crack Torsion (ECT) specimen for mode 3 interlaminar fracture toughness. Data reduction methods for mode 3 toughness based on the present analysis are proposed. The effect of the transverse shear modulus, G(sub 23), on mode 3 interlaminar fracture toughness characterization was evaluated. Parameters influenced by the transverse shear modulus were identified. Analytical results indicate that a higher value of G(sub 23) results in a low load point compliance and lower mode 3 toughness estimation. The effect of G(sub 23) on the mode 3 toughness using the ECT specimen is negligible when an appropriate initial delamination length is chosen. A conservative estimation of mode 3 toughness can be obtained by assuming G(sub 23) = G(sub 12) for any initial delamination length.

Li, Jian↗
NASA NTRS1989

Magneto-inductive skin sensor for robot collision avoidance: A new development

Safety is a primary concern for robots operating in space. The tri-mode sensor addresses that concern by employing a collision avoidance/management skin around the robot arms. This rf-based skin sensor is at present a dual mode (proximity and tactile). The third mode, pyroelectric, will complement the other two. The proximity mode permits the robot to sense an intruding object, to range the object, and to detect the edges of the object. The tactile mode permits the robot to sense when it has contacted an object, where on the arm it has made contact, and provides a three-dimensional image of the shape of the contact impression. The pyroelectric mode will be added to permit the robot arm to detect the proximity of a hot object and to add sensing redundancy to the two other modes. The rf-modes of the sensing skin are presented. These modes employ a highly efficient magnetic material (amorphous metal) in a sensing technique. This results in a flexible sensor array which uses a primarily inductive configuration to permit both capacitive and magnetoinductive sensing of object; thus optimizing performance in both proximity and tactile modes with the same sensing skin. The fundamental operating principles, design particulars, and theoretical models are provided to aid in the description and understanding of this sensor. Test results are also given.

Chauhan, D. S.↗
NASA NTRS2013

Geometric Effects on the Amplification of First Mode Instability Waves

The effects of geometric changes on the amplification of first mode instability waves in an external supersonic boundary layer were investigated using numerical techniques. Boundary layer stability was analyzed at Mach 6 conditions similar to freestream conditions obtained in quiet ground test facilities so that results obtained in this study may be applied to future test article design to measure first mode instability waves. The DAKOTA optimization software package was used to optimize an axisymmetric geometry to maximize the amplification of the waves at first mode frequencies as computed by the 2D STABL hypersonic boundary layer stability analysis tool. First, geometric parameters such as nose radius, cone half angle, vehicle length, and surface curvature were examined separately to determine the individual effects on the first mode amplification. Finally, all geometric parameters were allowed to vary to produce a shape optimized to maximize the amplification of first mode instability waves while minimizing the amplification of second mode instability waves. Since first mode waves are known to be most unstable in the form of oblique wave, the geometries were optimized using a broad range of wave frequencies as well as a wide range of oblique wave angles to determine the geometry that most amplifies the first mode waves. Since first mode waves are seen most often in flows with low Mach numbers at the edge of the boundary layer, the edge Mach number for each geometry was recorded to determine any relationship between edge Mach number and the stability of first mode waves. Results indicate that an axisymmetric cone with a sharp nose and a slight flare at the aft end under the Mach 6 freestream conditions used here will lower the Mach number at the edge of the boundary layer to less than 4, and the corresponding stability analysis showed maximum first mode N factors of 3.

Kirk, Lindsay C.↗
NASA NTRS1984

Leading edge flap system for aircraft control augmentation

Traditional roll control systems such as ailerons, elevons or spoilers are least effective at high angles of attack due to boundary layer separation over the wing. This invention uses independently deployed leading edge flaps on the upper surfaces of vortex stabilized wings to shift the center of lift outboard. A rolling moment is created that is used to control roll in flight at high angles of attack. The effectiveness of the rolling moment increases linearly with angle of attack. No adverse yaw effects are induced. In an alternate mode of operation, both leading edge flaps are deployed together at cruise speeds to create a very effective airbrake without appreciable modification in pitching moment. Little trim change is required.

Rao, D. M.↗
NASA NTRS1991

Analysis of matrix cracking and local delamination in (0/theta/-theta)sub s graphite epoxy laminates under tension load

Several 3D finite element analyses of (0/theta/-theta)sub s graphite epoxy laminates, where theta=15, 20, 25, 30, and 45 deg, subjected to axial tension load were performed. The interlaminar stresses in the theta/-theta interface were calculated with and without a matrix crack in the central -theta plies. The interlaminar normal stress changes from a small compressive stress when no matrix crack is present to a high tensile stress at the intersection of the matrix crack and free edge. The analysis of local delamination from the -theta matrix crack indicates a high strain energy release rate and a localized mode I component near the free edge, within one ply distance from the matrix crack. In order to examine the stress state causing the matrix cracking the maximum principal normal stress in a plane perpendicular to the fiber direction in the -theta ply was calculated in an uncracked laminate. The corresponding shear stress parallel to the fiber was also calculated. The principal normal stress at the laminate edge increases through the ply thickness and reached a very high tensile value at the theta/-theta interface indicating that the crack in the -theta ply may initiate at the theta/-theta interface. Crack profiles on the laminate edge in the -theta ply were constructed from the principal stress directions. The cracks were found to be more curved for layups with smaller theta angles, which is consistent with experimental observations in the literature.

Salpekar, S. A.↗
NASA NTRS1991

Analysis of matrix cracking and local delamination in (O/theta/-theta)sub s graphite epoxy laminates under tension load

Several 3D finite element analyses of (O/theta/-theta)sub s graphite epoxy laminates, where theta = 15, 20, 25, 30, and 45 deg, subjected to axial tension load were performed. The interlaminar stresses in the theta/-theta interface were calculated with and without a matrix crack in the central -theta plies. The interlaminar normal stress changes from a small compressive stress when no matrix crack is present to a high tensile stress at the intersection of the matrix crack and free edge. The analysis of local delamination from the -theta matrix crack indicates a high strain energy release rate and a localized mode I component near the free edge, within one ply distance from the matrix crack. In order to examine the stress state causing the matrix cracking the maximum principal normal stress in a plane perpendicular to the fiber direction in the -theta ply was calculated in an uncracked laminate. The corresponding shear stress parallel to the fiber was also calculated. The principal normal stress at the laminate edge increases through the ply thickness and reached a very high tensile value at the theta/-theta interface indicating that the crack in the -theta ply may initiate at the theta/-theta interface. Crack profiles on the laminate edge in the -theta ply were constructed from the principal stress directions. The cracks were found to be more curved for layups with smaller theta angles, which is consistent with experimental observations in the literature.

Salpekar, S. A.↗