Search NASA⌕ Search

SEARCH · Search NASA

Results for “effect size”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Unifying first-principles theoretical predictions and experimental measurements of size effects in thermal transport in SiGe alloys

We demonstrate the agreement between first-principles calculations and experimental measurements of size effects in thermal transport in SiGe alloys without fitting parameters. Transient thermal grating (TTG) is used to measure the effect of the grating period on the temperature decay. The virtual crystal approximation under the density-functional-theory framework combined with impurity scattering is used to determine the phonon properties for the exact alloy composition of the measured samples. With these properties, classical size effects are calculated for the experimental geometry of reflection mode TTG using the recently developed variational solution to the phonon Boltzmann transport equation, which is verified against established Monte Carlo simulations. Here, we find agreement between theoretical predictions and experimental measurements in the reduction of thermal conductivity (as much as fourfold of the bulk value) across grating periods spanning one order of magnitude. This paper provides a framework for the study of size effects in thermal transport in opaque materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pyroelectric response of ferroelectric nanowires: Size effect and electric energy harvesting

The size effect on pyroelectric response of ferroelectric nanowires is analyzed. The pyroelectric coefficient strongly increases with the wire radius decrease and diverges at critical radius Rcr corresponding to the size-driven transition into paraelectric phase. Size-driven enhancement of pyroelectric coupling leads to the giant pyroelectric current and voltage generation by the polarized ferroelectric nanoparticles in response to the temperature fluctuation. The maximum efficiency of the pyroelectric energy harvesting and bolometric detection is derived, and is shown to approach the Carnot limit for low temperatures.

Morozovska, A. N.↗

Review of Size Effects during Micropillar Compression Test: Experiments and Atomistic Simulations

The micropillar compression test is a novel experiment to study the mechanical properties of materials at small length scales of micro and nano. The results of the micropillar compression experiments show that the strength of the material depends on the pillar diameter, which is commonly termed as size effects. In the current work, first, the experimental observations and theoretical models of size effects during micropillar compression tests are reviewed in the case of crystalline metals. In the next step, the recent computer simulations using molecular dynamics are reviewed as a powerful tool to investigate the micropillar compression experiment and its governing mechanisms of size effects.

36 MATERIALS SCIENCE↗

Finite-size effects in the dynamic conductivity and Faraday effect of quantum anomalous Hall insulators

Here, we theoretically study the finite-size effects in the dynamical response of a quantum anomalous Hall insulator in the disk geometry. Semianalytic and numerical results are obtained for the wave functions and energies of the disk within a continuum Dirac Hamiltonian description subject to a topological infinite mass boundary condition. Using the Kubo formula, we obtain the frequency-dependent longitudinal and Hall conductivities and find that optical transitions between edge states contribute dominantly to the real part of the dynamic Hall conductivity for frequency values both within and beyond the bulk band gap. We also find that the topological infinite mass boundary condition changes the low-frequency Hall conductivity to e 2 / h in a finite-size system from the well-known value e 2 / 2 h in an extended system. The magneto-optical Faraday rotation is then studied as a function of frequency for the setup of a quantum anomalous Hall insulator mounted on a dielectric substrate, showing both finite-size effects of the disk and Fabry-Pérot resonances due to the substrate. Our work shows the vital role played by the boundary condition in the topological properties of finite-size systems through its effects on the electronic wave functions.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Investigation of specimen size effects by in-situ microcompression of equal channel angular pressed copper

Here, micropillar compression testing was implemented on Equal Channel Angular Pressed copper samples ranging from 200 nm to 10 µm in side length in order to measure the mechanical properties yield strength, first load drop during plastic deformation at which there was a subsequent stress decrease with increasing strain, work hardening, and strain hardening exponent. Several micropillars containing multiple grains were investigated in a 200 nm grain sample. The effective pillar diameter to grain size ratios, D/d , were measured to be between 1.9 and 27.2. Specimens having D/d ratios between 0.2 and 5 were investigated in a second sample that was annealed at 200 °C for 2 h with an average grain size of 1.3 µm. No yield strength or elastic modulus size effects were observed in specimens in the 200 nm grain size sample. However work hardening increases with a decrease in critical ratios and first stress drops occur at much lower stresses for specimens with D/d ratios less than 5. For comparison, bulk tensile testing of both samples was performed, and the yield strength values of all micropillar compression tests for the 200 nm grained sample are in good agreement with the yield strength values of the tensile tests.

36 MATERIALS SCIENCE↗

Very High Cycle Fatigue of a Cast Aluminum Alloy: Size Effect and Crack Initiation

Fatigue properties of an Al-Si-Cu cast alloy were investigated with life up to very high cycle fatigue regime. Particular attention was given to specimen size effect and fatigue crack initiation mechanism. Uniaxial fatigue tests with constant amplitudes were carried out by using ultrasonic fatigue testing machine operating at 20 kHz, compared to the results obtained by using conventional hydraulic fatigue machine at 35 Hz. In order to evaluate the size effect, two sets of specimens with different dimensions were used. The results show that the fatigue strength of the studied alloy decreases with the increase in specimen size. Scanning electron microscopy observation of fracture surfaces revealed that most fatigue cracks initiated from microstructural defects such as porosity located on specimen surface or in subsurface. Weibull statistical analysis of fatigue data accounting for size effect was performed to predict the fatigue life of the Al-Si-Cu alloy in the very high cycle regime. Good agreement was found between the fatigue life prediction and the experimental data.

36 MATERIALS SCIENCE↗

Sample Size Effects on Petrophysical Characterization and Fluid-to-Pore Accessibility of Natural Rocks

Laboratory-scale analysis of natural rocks provides petrophysical properties such as density, porosity, pore diameter/pore-throat diameter distribution, and fluid accessibility, in addition to the size and shape of framework grains and their contact relationship with the rock matrix. Different types of laboratory approaches for petrophysical characterization involve the use of a range of sample sizes. While the sample sizes selected should aim to be representative of the rock body, there are inherent limitations imposed by the analytical principles and holding capacities of the different experimental apparatuses, with many instruments only able to accept samples at the μm–mm scale. Therefore, a total of nine (three limestones, three shales, two sandstones, and one dolomite) samples were collected from Texas to fill the knowledge gap of the sample size effect on the resultant petrophysical characteristics. The sample sizes ranged from 3 cm cubes to <75 μm particles. Using a combination of petrographic microscopy, helium expansion pycnometry, water immersion porosimetry, mercury intrusion porosimetry, and (ultra-) small-angle X-ray scattering, the impact of sample size on the petrophysical properties of these samples was systematically investigated here. The results suggest that the sample size effect is influenced by both pore structure changes during crushing and sample size-dependent fluid-to-pore connectivity.

36 MATERIALS SCIENCE↗

Orientation influence on grain size-effects in ultrafine-grained magnesium

The mechanical behavior of ultrafine-grained magnesium was studied by discrete dislocation dynamics (DDD) simulations. Our results show basal slip yields a strong size effect, while prismatic and pyramidal slips produce a weak one. We developed a new size-strength model that considers dislocation transmission across grain boundaries. Good agreement between this model, current DDD simulations and previous experiments is observed. These results reveal that the grain size effect depends on 3 factors: Peierls stress, dislocation source strength and grain boundary strength.

36 MATERIALS SCIENCE↗

Field-size effect of physical doses in carbon-ion scanning using range shifter plates

A field-size effect of physical doses was studied in scanning irradiation with carbon ions. For the target volumes of 60x60x80, 40x40x80, and 20x20x80 mm{sup 3}, the doses along the beam axis within the spread-out Bragg peaks reduced to 99.4%, 98.2%, and 96.0% of the dose for the target of 80x80x80 mm{sup 3}, respectively. The present study revealed that the observed reductions can be compensated for by adopting the three-Gaussian form of lateral dose distributions for the pencil beam model used in the treatment planning system. The parameters describing the form were determined through the irradiation experiments making flat concentric squared frames with a scanned carbon beam. Since utilizing the three-Gaussian model in the dose optimization loop is at present time consuming, the correction for the field-size effect should be implemented as a ''predicted-dose scaling factor.'' The validity of this correction method was confirmed through the irradiation of a target of 20x20x80 mm{sup 3}.

61 RADIATION PROTECTION AND DOSIMETRY↗

Single- and two-particle finite size effects in interacting lattice systems

Simulations of extended quantum systems are typically performed by extrapolating results of a sequence of finite-system-size simulations to the thermodynamic limit. In the quantum Monte Carlo community, twist-averaging was pioneered as an efficient strategy to eliminate one-body finite size effects. In the dynamical mean field community, cluster generalizations of the dynamical mean field theory were formulated to study systems with nonlocal correlations. In this work, we put the twist-averaging and the dynamical cluster approximation variant of the dynamical mean field theory onto equal footing, discuss commonalities and differences, and compare results from both techniques to the standard periodic boundary technique. At the example of Hubbard-type models with local, short-range and Yukawa-like longer range interactions we show that all methods converge to the same limit, but that the convergence speed differs in practice. We show that embedding theories are an effective tool for managing both one-body and two-body finite size effects, in particular if interactions are averaged over twist angles.

36 MATERIALS SCIENCE↗

Size effects on the thermal conductivity of amorphous silicon thin films

In this study, we investigate thickness-limited size effects on the thermal conductivity of amorphous silicon thin films ranging from 3 to 1636 nm grown via sputter deposition. While exhibiting a constant value up to ~100 nm, the thermal conductivity increases with film thickness thereafter. The thickness dependence we demonstrate is ascribed to boundary scattering of long wavelength vibrations and an interplay between the energy transfer associated with propagating modes (propagons) and nonpropagating modes (diffusons). A crossover from propagon to diffuson modes is deduced to occur at a frequency of ~1.8 THz via simple analytical arguments. These results provide empirical evidence of size effects on the thermal conductivity of amorphous silicon and systematic experimental insight into the nature of vibrational thermal transport in amorphous solids.

36 MATERIALS SCIENCE↗

Finite-size effects on hot hadron-quark mixed phase including hyperons

We study the hadron-quark phase transition with finite size effects at a finite temperature. For the hadron phase, we adopt a realistic equation of state with the Brueckner-Hartree-Fock theory including hyperons. Properties of the mixed phase are clarified by considering the finite size effects under the Gibbs conditions. We find that the equation of state gets closer to that given by the Maxwell construction. We also find that the equation of state becomes softer than that at a zero temperature for some density region. Moreover, the number of hyperons is suppressed by the presence of quarks. These are characteristic features of the hadron-quark mixed phase, and should be important for many astrophysical phenomena such as mergers of binary neutron stars.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Finite-size effects for the gap in the excitation spectrum of the one-dimensional Hubbard model

We study finite-size effects for the gap of the quasiparticle excitation spectrum in the weakly interacting regime one-dimensional Hubbard model with on-site attraction. Two types of corrections to the result of the thermodynamic limit are obtained. Aside from a power law (conformal) correction due to gapless excitations which behaves as 1/N{sub a}, where N{sub a} is the number of lattice sites, we obtain corrections related to the existence of gapped excitations. First of all, there is an exponential correction which in the weakly interacting regime (|U|<<t) behaves as approxexp(-N{sub a}DELTA{sub i}nfinity/4t) in the extreme limit of N{sub a}DELTA{sub i}nfinity/t>>1, where t is the hopping amplitude, U is the on-site energy, and DELTA{sub i}nfinity is the gap in the thermodynamic limit. Second, in a finite-size system a spin-flip producing unpaired fermions leads to the appearance of solitons with nonzero momenta, which provides an extra (nonexponential) contribution delta. For moderate but still large values of N{sub a}DELTA{sub i}nfinity/t, these corrections significantly increase and may become comparable with the 1/N{sub a} conformal correction. Moreover, in the case of weak interactions where DELTA{sub i}nfinity<<t, the exponential correction exceeds higher-order power law corrections in a wide range of parameters, namely for N{sub a} < or approx. (8t/DELTA{sub i}nfinity)ln(4t/|U|), and so does delta even in a wider range of N{sub a}. For a sufficiently small number of particles, which can be of the order of thousands in the weakly interacting regime, the gap is fully dominated by finite-size effects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Characterizing the Joint Effect of Diverse Test-Statistic Correlation Structures and Effect Size on False Discovery Rates in a Multiple-Comparison Study of Many Outcome Measures

In their 2009 Annals of Statistics paper, Gavrilov, Benjamini, and Sarkar report the results of a simulation assessing the robustness of their adaptive step-down procedure (GBS) for controlling the false discovery rate (FDR) when normally distributed test statistics are serially correlated. In this study we extend the investigation to the case of multiple comparisons involving correlated non-central t-statistics, in particular when several treatments or time periods are being compared to a control in a repeated-measures design with many dependent outcome measures. In addition, we consider several dependence structures other than serial correlation and illustrate how the FDR depends on the interaction between effect size and the type of correlation structure as indexed by Foerstner s distance metric from an identity. The relationship between the correlation matrix R of the original dependent variables and R~, the correlation matrix of associated t-statistics is also studied. In general R~ depends not only on R, but also on sample size and the signed effect sizes for the multiple comparisons.

Feiveson, Alan H.↗

Finite size effects in L1{sub o}-FePt nanoparticles

Finite size effects on the temperature dependence of the uniaxial magnetic anisotropy, longitudinal and transverse susceptibilities and specific heat are examined for L1{sub o}-ordered FePt nanoparticles using an atomistic model based on an effective classical spin Hamiltonian. At low temperatures below criticality, we study the intrinsic uniaxial magnetic anisotropy energy (MAE) K{sub 1} and its scaling with magnetization K{sub 1}(T)∼M{sub s}(T){sup δ} and using Langevin dynamics simulations we show that the dependence of the exponent δ on the size L and aspect ratio of the grain arises from decomposition of the MAE into bulk and surface dependent terms. Monte Carlo simulations in the critical regime near the Curie temperature T{sub c}, show that the temperature variation of the specific heat and longitudinal susceptibility is given by finite size scaling relations c=L{sup α/ν}c{sup ~}(L{sup 1/ν}ϵ) and χ=L{sup γ/ν}χ{sup ~}(L{sup 1/ν}ϵ), respectively, where ϵ=(T−T{sub c})/T{sub c} is the reduced temperature, and the susceptibility scaling function χ{sup ~} can be approximated by a Lorentzian. Our estimates of the critical exponents α,γ, and ν appear to be in agreement with the universality class of the 3D Ising model.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Finite-size effects on the radiative energy loss of a fast parton in hot and dense strongly interacting matter

We consider finite-size effects on the radiative energy loss of a fast parton moving in a finite-temperature, strongly interacting medium, using the light-cone path integral formalism put forward by B. G. Zakharov [JETP Lett. 63, 952 (1996); 65, 615 (1997)]. We present a convenient reformulation of the problem that makes possible its exact numerical analysis. This is done by introducing the concept of a radiation rate in the presence of finite-size effects. This effectively extends the finite-temperature approach of Arnold, Moore, and Yaffe [J. High Energy Phys. 11 (2001) 057; 12 (2001) 009; 06 (2001) 030] (AMY) to include interference between vacuum and medium radiation. We compare results with those obtained in the regime considered by AMY, with those obtained at leading order in an opacity expansion, and with those obtained deep in the Landau-Pomeranchuk-Migdal regime.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗